Digital Commons Network^™

Properties Of Air-Entrained Concrete At Early Ages, Ugur Ozoguz

Masters Theses

"This study, entitled "Properties of Air-Entrained Concrete at Early Ages" concerns a group of tests designed to provide quantitative information regarding the effect of entrained air on the strength and durability of concrete before it reaches its 28 day strength.

Experiences in the field and laboratories have demonstrated that the addition of a moderate amount of air to any concrete mix will bring a marked increase in resistance to the disintegrating effects of freezing and thawing.

There have been extensive studies made on the subject of durability of air entrained concrete. Most of these studies were based on the effect …

An Experimental Study Of The Effects Of Additives On The Collapsibility Of Carbon Dioxode-Sodium Silicate Bonded Foundry Cores, Robert G. Liptai

Masters Theses

"Every foundry is searching for methods and tools to raise product quality and production while lowering cost. In early 1954 published articles on the new carbon dioxide-sodium silicate process of core hardening began to stir the imagination of most of the foundries throughout the United States, This process has probably claimed more space in the foundry journals than any other subject, hailed by some as a cure-all and dismissed by others as unsatisfactory.

The list of advantages of this process was impressive, but anyone associated with the process was confronted with daily problems that had to be solved regardless of …

Critical Load For A Rectangular Plate Simply Supported On Three Edges, Built In On The Fourth Edge, And Compressed On Two Opposite Simply Supported Edges By A Load In The Plane Of The Plate, Bert Louis Smith

Masters Theses

"There are many engineering structures in which thin plates are used extensively, some examples of which can be found in ship and airplane structures, bridges, etc. The problem contained in this thesis is the analysis of a thin rectangular plate simply supported on three edges, built in on the fourth edge, and compressed on two opposite simply supported edges by a load in the plane or the plate. This problem becomes one of stability, and the object of the solution is to find the smallest load that will cause the plate to buckle"--Introduction, page vi.

A Method Of Design For Spiral Reinforced, Eccentrically Loaded, Concrete Columns, Lloyd O. Senter

Masters Theses

"This thesis presents a method of designing spiral reinforced, eccentrically loaded, concrete columns on the basis of the 1957 American Association of State Highway Officials specifications.

Equations from AASHO, in conjunction with equations derived in this thesis, are programmed for and solved by the IBM 650 digital computer. The data obtained from the computer is plotted such that, given the normal load and moment on a column, the minimum required area or reinforcing steel may be read directly from the graph.

The derivation or equations, the computer program, and the graphs are included in the thesis"--Introduction, page 1.

The Missouri Miner, December 18, 1959

The Missouri Miner Newspaper

No abstract provided.

The Missouri Miner, November 13, 1959

The Missouri Miner Newspaper

No abstract provided.

Missouri S&T Magazine, November-December 1959, Miner Alumni Association

Missouri S&T Magazine

No abstract provided.

Missouri S&T Magazine, September-October 1959, Miner Alumni Association

Missouri S&T Magazine

No abstract provided.

Missouri S&T Magazine, July-August 1959, Miner Alumni Association

Missouri S&T Magazine

No abstract provided.

The Missouri Miner, May 15, 1959

The Missouri Miner Newspaper

No abstract provided.

Missouri S&T Magazine, May-June 1959, Miner Alumni Association

Missouri S&T Magazine

No abstract provided.

Missouri S&T Magazine, March-April 1959, Miner Alumni Association

Missouri S&T Magazine

No abstract provided.

The Missouri Miner, February 27, 1959

The Missouri Miner Newspaper

No abstract provided.

The Effect Of Rare Earth Additions On Low Alloy Steel, Sukh Dev Sehgal

Masters Theses

"Rare earth metals have for some years been used as an inoculant in nonferrous foundry practice and lately in the production of nodular iron. It has been reported that addition of rare earth metal to certain grades of stainless steel so improve the hot malleability that reduction of large size ingots in the blooming mill is now possible. It has been reported that considerable improvement in soundness and mechanical properties of steel castings and wrought products have been attained as a result of small additions of rare earth metals and oxides. In practically all investigations, it has been reported that …

X-Ray Diffraction Study Of The Metal Powder Compacts, Rajendra Sharan

Masters Theses

"Various theories have been put forward about the mechanism of compacting and sintering processes. None of these theories are confirmed. The reason is that most of these theories are based on observations on metallographic specimens, which is not a particularly good tool for such a study. Little data using xray diffraction analysis is available and there seems to be a great need of making a thorough investigation in this direction.

The main object of this investigation is to study xray diffraction patterns of green compacts of aluminum, nickel and copper powders pressed under different compacting pressures to see if any …

Geology Of The Copper Deposits In The Eminence Region, Shannon County, Missouri, Lanny Lee Evans

Masters Theses

"Copper has been known to occur in Shannon County, Missouri since the early 1830's. A number of small deposits in an area around Eminence has been worked intermittently up to the present day. Little detailed geologic information is available on these deposits. The geology of the Eminence region consists of Precambrian rhyolite porphyry knobs projecting through dolomites and sandstones of Upper Cambrian and Ordovician age. A conglomerate of limited horizontal extent overlying the Precambrian is found at certain localities within the region. The only structures noted are the structural highs formed where the Paleozoic sediments lap upon the knobs. The …

Bonded Joint Strength Versus Loading Rate, Charless William Fowlkes

Masters Theses

"The purpose of this investigation was to determine the influence of the rate of loading variable on the apparent shear strengths of joints bonded with some of the currently available metal-to-metal adhesives. The effects of this variable are sometimes neglected by testing laboratories. The results of an experimental evaluation of the mechanical behavior of a group on modern metal-to-metal adhesives as a function of the rate of load application are used to more accurately establish the importance of rate of load considerations in adhesive joint testing. An attempt is made to explain observations of other investigators engaged in adhesive joint …

Stability Of Rectangular Plates By Arbitrary Deflection Method, James Arthur Jones

Masters Theses

"Many engineering structures use thin rectangular plates as members. These plates may be loaded and supported in numerous ways. The edges may be freely supported, rigidly supported, or supported by elastic members. The load may be applied normal to the plane of the plate, in which case the problem becomes essentially one of bending. If the load is applied in the plane of the plate, placing it in compression, the problem becomes one of stability.

This investigation is concerned with the stability of plates rigidly supported on all edges and having a compressive load applied to two opposite edges of …

Linear And Vortex Flow Heat Transfer Coefficients, Edward Robert Schmidt Jr.

Masters Theses

"In order to make possible better, more efficient equipment, a higher and higher rate of heat transfer has been the goal of engineers for many years. The need for heat transfer rates never thought of 25 years ago has been brought about by the advent of modern high-performance devices such as nuclear reactors and rocket motors. "A heat release of about 40,000 Btu/hr.cu.ft. is considered good practice in a modern boiler, but in a rocket or a nuclear reactor it may be 1,000,000,000 Btu/hr.cu.ft." This heat must be removed by transfer to a coolant or converted into work or the …

A Preliminary Search For Subionizers, Joseph B. Hughes

Masters Theses

"A number of physicists of recent years have been attempting to explain the basic nature of the universe in terms of particles. A few particles have been predicted theoretically, and some of these, along with many others have appeared experimentally, Searches for them have presented some interesting experimental problems and brought forth some invaluable experimental apparatus. One of these devices is the Wilson cloud chamber, with which this thesis is concerned.

Of the particles that have been discovered thus far, only the electron and the proton appear to be stable. The rest ultimately decay by the emission of photons and …

Steady State Temperature Distribution In A Rotating Disk, George Henry Morgan

Masters Theses

"The purpose of this investigation was to obtain an expression for the steady state temperature distribution of a disk of uniform thickness rotating at a constant speed in ambient air while absorbing heat through the periphery at a constant rate. Engineers encounter such problems in connection with brakes of several varieties. The general solution obtained here could be extended to similar physical problems such as grinding wheels, disk clutches, and so on.

A differential equation was obtained for the temperature in the disk by the application of Fourier's conduction law and Newton’s convection law. A solution of this equation was …

Lattice Constants, Thermal Expansion Coefficients And Perfection Of The Phase Tio, Hsiung Wei Li

Masters Theses

"TiO is one of the intermediate phases in the titanium - oxygen system with a crystal structure of the sodium chloride type. The phase extends from about 22 to 29 weight or about 46 to 55 atomic percent oxygen. A comprehensive survey of the physical properties of the phase has been made in previous investigations (see review of literature), but only impure titanium was available at that time. Therefore, some revision of the measurements had to be made. Also, neither the thermal expansion coefficients nor the temperature at which the lattice constants were measured were reported.

For precision determination of …

The Missouri Miner, December 12, 1958

The Missouri Miner Newspaper

No abstract provided.

Missouri S&T Magazine, November-December 1958, Miner Alumni Association

Missouri S&T Magazine

No abstract provided.

The Missouri Miner, October 24, 1958

The Missouri Miner Newspaper

No abstract provided.

The Missouri Miner, October 10, 1958

The Missouri Miner Newspaper

No abstract provided.

Missouri S&T Magazine, March-April 1958, Miner Alumni Association

Missouri S&T Magazine

No abstract provided.

The Missouri Miner, February 28, 1958

The Missouri Miner Newspaper

No abstract provided.

Investigation Of The Geometric Effects Connected With The U-Effect-Iii, Anthony Edward Hoffman

Masters Theses

"Statement of Problem: The investigation reported herein is of the dependence of the voltage output due to the U-Effect-III upon the geometry of the tube. The geometry of the tube is defined to include the inner diameter of the tube as well as the size and number of the mercury and electrolyte drops. The previous experimental study of the effect did not include an investigation of the effects of the geometry of the tube, as defined above, on the voltage output. It seems that information as to the dependence of the output voltage on the geometry of the tube would …

Rheological Measurement Of A Starch Suspension As A Dilatant Fluid, Earl Edward Pape

Masters Theses

"The measurement of the rheological properties, consistency of viscosity and fluid type, necessary for system design calculations, has fallen behind the industrial applications for non-Newtonian fluids. In the petroleum industry in particular, the process of well flow stimulation known as Hydraulic Fracturing utilizes the properties of various non-Newtonian fluids to carry sand at high flow rates to the formation to be fractured. Other non-Newtonian fluids in the petroleum industry are Bentonite clay drilling fluids, whose unique gelling properties are helpful in suspending drill cuttings when the circulation of the fluid has ceased. In Newtonian liquids and gases the consistency is …