Digital Commons Network^™

The Missouri Miner, January 25, 1979

The Missouri Miner Newspaper

No abstract provided.

Newtruck: A Comprehensive Long-Term Project In Computer Science, Daniel C. St. Clair

Mathematics and Statistics Faculty Research & Creative Works

No abstract provided.

Processing Of Copper Refinery Anode Slimes, Shrirang Anant Kulkarni

Masters Theses

"A study of commercial copper refinery anode slimes has been conducted to evaluate the separation of valuable metals contained in the slimes. The slimes contain substantial quantities of Ag, Sn, Au, Pb, and Cu. The values were present principally as AgCl, SnO₂, Au, PbSO₄, Cu and CuSO₄.

A Roast-Leach-Roast-Leach (RLRL) technique solubilized up to 91 pct of the Ag and 99 pct of the Cu from raw slimes.

The Pb-Sn separation was investigated using the following hydrometallurgical techniques: 1) DETA (diethylene triamine) leaching; 2) NaOH leaching; 3) (NH₄)₂CO₃ leaching; …

Pelletizing Of A Lead Sinter Machine Feed, Hung-Yang Tsai

Masters Theses

"A typical lead sinter machine feed can be pelletized in a drum pelletizer using tap water as a binding liquid. The green pellets produced have return sinter as cores, and an outer layer of new material and fluxes. The moisture content of the pellets produced is about 5%. The pelletizing procedure developed used raw materials from the Amax Lead Smelter, with only a minor amount of feed preparation. The importance of proper moisture control, use of binders, method of adding moisture, speed of pelletizing drum, etc. were investigated. The stability of pellets under extreme storage conditions was also determined"--page ii.

A Metallurgical Evaluation Of The Mi Vida Prospect: A Mixed Copper Sulfide-Carbonate Ore Body, Sells, Pima County, Arizona, Kevin Michael Kenney

Masters Theses

"A copper-prospect in south-central Arizona has been evaluated on a metallurgical basis. Primary chalcocite and secondary covellite, plus the copper oxides malachite and brochantite, constitute the economic mineralization. The deposit outcrops as a steeply dipping (70°SW), intensely brecciated, copper-bearing quartz vein with discontinuous lenticular ore shoots.

Acid leaching techniques alone and in conjunction with froth flotation utilizing four copper oxide specific collectors were used to evaluate the amenability of this ore to processing. Direct acid leaching was examined and found to be ineffective. Removal of the chalcocite by froth flotation with xanthate was easy and gave better results to subsequent …

Two-Dimensional Scattering From A Medium Of Finite Thickness, Dwight C. Look

Mechanical and Aerospace Engineering Faculty Research & Creative Works

No abstract provided.

Motion‐Compensated Transform Coding, A. N. Netravali, J. A. Stuller

Electrical and Computer Engineering Faculty Research & Creative Works

Interframe Hybrid Transform/dpcm Coders Encode Television Signals by Taking a Spatial Transform of a Block of Picture Elements in a Frame and Predictively Coding the Resulting Coefficients using the Corresponding Coefficients of the Spatial Block at the Same Location in the Previous Frame. These Coders Can Be Made More Efficient for Scenes Containing Objects in Translational Motion by First Estimating the Translational Displacement of Objects and Then using Coefficients of a Spatially Displaced Block in the Previous Frame for Prediction. This Paper Presents Simulation Results for Such Motion‐compensated Transform Coders using Two Algorithms for Estimating Displacements. the First Algorithm, Which …

Reduction Of Transmission Error Propagation In Adaptively Predicted, Dpcm Encoded Pictures, N. F. Maxemchuk, J. A. Stuller

Electrical and Computer Engineering Faculty Research & Creative Works

A New Technique for Reducing Transmission Error Propagation in Adaptively Predicted, dpcm‐encoded Pictures is Described. the Basis for the Technique is a Generalization of the Notion of Predictor Output Attenuation, Described by Graham, to Include Attenuation of the Adaptive Prediction Function. Simulation Results Are Presented that Show that Application of the Technique to Graham's Codec Results in Significant Reduction in Error Propagation Without Degradation of Picture Quality. the Technique Requires No Increase in Transmission Rate. © 1979 the Bell System Technical Journal

Backscatter Inversion In Spherically Asymmetric Ionosphere, R. (Richard) E. Dubroff, N. Narayana Rao, K. C. Yeh

Electrical and Computer Engineering Faculty Research & Creative Works

It is Well Known that Various Diurnal and Morphological Features of the Ionosphere Reveal Substantial Departures from the Normally Simplified Assumption of Spherical Symmetry at Certain Times of the Day or at Certain Geographic Locations. a Radio Ray Passing through Such an Ionosphere Must Bear Information About its Horizontal Gradients. the Leading Edge of a Backscatter Ionogram is Formed by Obliquely Propagated Radio Rays of Minimum Time Delay and Hence is Useful in Deducing Information About the Ionospheric Horizontal Gradients. in This Regard, the Ionospheric Electron Density Distribution is Modeled by a Locally Quasi‐parabolic Layer with Six Parameters. This Six‐parameter …

Series Induction/Parallel Inverter Power Stage And Power Staging Method For Dc-Dc Power Converter, Don Cronin, John J. Biess

Mechanical and Aerospace Engineering Faculty Research & Creative Works

An improved series inductor/parallel inverter power stage and power staging method for a transistor controlled DC-DC power converter in which the integrating capacitance is located in the output of the power stage transformer and the series inductor has a secondary winding connected across this capacitance for transferring stored energy from the inductor primary directly to the transformer output rather than through the transformer, and current flow through the transformer primary is controlled by two parallel, alternately conducting pulse-width-modulated transistors in a manner such that only a single transistor is located in the main current flow path at any given time. …

Transform Domain Motion Estimation, J. A. Stuller, A. N. Netravali

Electrical and Computer Engineering Faculty Research & Creative Works

This Paper Introduces an Algorithm for Estimating the Displacement of Moving Objects in a Television Scene from Spatial Transform Coefficients of Successive Frames. the Algorithm Works Recursively in Such a Way that the Displacement Estimates Are Updated from Coefficient to Coefficient. a Promising Application of This Algorithm is in Motion‐compensated Interframe Hybrid Transform‐dpcm Image Coding. We Give a Statistical Analysis of the Transform Domain Displacement Estimation Algorithm and Prove its Convergence under Certain Realistic Conditions. an Analytical Derivation is Presented that Gives Sufficient Conditions for the Rate of Convergence of the Algorithm to Be Independent of the Transform Type. This …

Structural Stability Research Council: Proceedings 1979, Structural Stability Research Council

CCFSS Library (1939 - present)

One of the purposes of the Council is to maintain a forum where problems related to the design and behavior of columns and other compression elements in metal structures can be presented for evaluation and discussion. The Annual Technical Session provides an opportunity to carry out this function. The 1979 Annual Technical Session was held on April 24 and 25 at The William Penn Hotel in Pittsburgh, Pennsylvania. Eighty-five persons attended the Session and twenty-seven papers were delivered. A panel discussion on "Stability of Space Frame Structures" was held in the evening of April 24, 1979. The panelists were R. …

Molybdenum Stability In Coal Slags At 1400⁰C: Corrosion Properties For Mhd Electrode Applications., Kenton Brian Wright

Masters Theses

"Molten coal slag corrosion studies conducted on molybdenum at 1400°C used static and stirred slag experiments and electrical current experiments to parallel electrode conditions of slagging duct MHD generators. Crucibles containing molybdenum and slag were exposed to combustion-type gases in a tube furnace. Carbon monoxide-carbon dioxide gas mixtures controlled oxygen partial pressures at selected values between 10^-11 and 10^-3 atm. Metallograph and microprobe examination of polished sample sections defined corrosion characteristics.

At 1400°C, molybdenum metal is stable below 10^-9 atm oxygen pressure. Molybdenum dioxide is stable at higher pressure, but volatile molybdenum trioxides prevent formation of stable …

Negative Ion Charge Transfer Of The Reaction Of S⁻ And O⁻ With Atomic Hydrogen Producing H⁻ Ions From 1500 To 10 Kev, George F. Hagner

Doctoral Dissertations

"The charge transfer reactions of 0^-, S^- with atomic hydrogen were studied from 1.5 to 10 KeV, and the reaction Cl^- + O₂ + O₂^- + Cl was studied from 10 eV to 10 KeV. The reactions studied were normalized to the reaction H^- + H + H + H^-. The maximum measured cross sections were 4.6 x 10^-16 cm² for the reaction Cl^- + O₂ + O₂^- + Cl and 4.4 x 10^-15 cm² for the reaction 0^- + H …

Plasma Polymerization Of Tetrafluoroethylene. Iii. Capacitive Audio Frequency (10 Khz) And Ac Discharge, N. (Nicholas) C. Morosoff, H. Yasuda, E. S. Brandt, C. N. Reilley

Chemical and Biochemical Engineering Faculty Research & Creative Works

The plasma polymerization of tetrafluoroethylene (TFE) is studied in a capacitively coupled system with internal electrodes using a 10 kHz (af) and a 60 Hz (ac) source. The emphasis is on identifying conditions that are compatible with continuous coating of plasma polymer on a substrate moving through the center of the interelectrode gap. Operation at a pressure below 100 mTorr is most favorable for deposition of a substantial portion of the plasma polymer on this substrate. Plasma polymer deposited in this way is characterized by ESCA and by deposition rate data and compared to that deposited using rf power in …

Plasma Polymerization Of Tetrafluoroethylene. Ii. Capacitive Radio Frequency Discharge, N. (Nicholas) C. Morosoff, H. Yasuda, E. S. Brandt, C. N. Reilley

Chemical and Biochemical Engineering Faculty Research & Creative Works

The plasma polymerization of tetrafluoroethylene (TFE) is studied in a capacitively coupled system with internal electrodes using radio frequency (13.56 MHz) power. The emphasis is on identifying conditions that are compatible with continuous coating of plasma polymer on a substrate moving through the center of the interelectrode gap. At high pressure (500 mTorr), deposition of plasma polymer is primarily on the electrodes rather than on a substrate placed midway between electrodes. Glow is observed in only part of the interelectrode gap at low powers and fills the gap only at high power levels. The use of a magnetic field effects …

Southwinds - Spring 1979

Southwinds: The Literary and Arts Magazine of Missouri S&T

SOUTHWINDS is published by the Greater Rolla-UMR Metropolitan Literary Society and is not an official publication of the University of Missouri--Rolla.

Mechanical Degradation Of High Molecular Weight Polymers In Dilute Solution, J. F.S. Yu, J. L. Zakin, Gary Kent Patterson

Chemical and Biochemical Engineering Faculty Research & Creative Works

The mechanical shear degradation of polydisperse Poly isobutene and monodisperse polystyrene in oils of different viscosities in the concentration range of 0.1% to 1% was studied using a high‐shear concentric cylinder viscometer under laminar and uniform well‐defined shear field conditions. Molecular weight distributions (MWDs) were measured by gel permeation chromatography (GPC). Degradation of polydisperse Poly isobutene solutions narrows the distributions principally through the breaking down of large molecules. Degradation of monodisperse polystyrene broadens the distributions at lower shear stress. At higher shear stresses, the distributions do not broaden as much but are still broader than those of the original polymer. …

Negative Ion Production Rates In Rare Gas-Halide Lasers, Kaare J. Nygaard, Howard L. Brooks, Scott R. Hunter

Physics Faculty Research & Creative Works

This paper reports on dissociative electron attachment in F2, NF3, Cl2, and I2. The principle of the method is to produce a short burst of photoelectrons from a photocathode by means of light from an argon-fluoride laser. Subsequently, by studying the motion of electrons and negative ions in a constant electric field (E) region, information is obtained about drift velocities and effective attachment cross sections. Helium, argon, and nitrogen were used as buffer gases. Of particular interest is a very strong temperature dependence of the attachment coefficient in I2. Measurements were taken from 35 to 110°C, covering an E/N range …

Precision Doubly Differential Cross Section Measurements, John T. Park

Physics Faculty Research & Creative Works

Ion Energy Loss Spectrometry has been applied to the measurement of cross sections differential in both scattering angle and ion energy loss. Differential cross sections obtained for excitation of the n=2 level of atomic hydrogen by various ions provides unexpectedly good agreement with the available theories. Copyright © 1978 by The Institute of Electrical and Electronics Engineers, Inc.

Temperature Dependence Of The Electron Attachment Coefficient In Iodine, Howard L. Brooks, Scott R. Hunter, Kaare J. Nygaard

Physics Faculty Research & Creative Works

The attachment coefficient for iodine in a (1% I2+99% N 2) mixture, 50 Torr total pressure, has been measured in an electron swarm experiment from 1 to 50 Townsends (1 Townsend=1Td=10-17 V cm2). As the temperature was increased from 35 to 110°C, the attachment coefficient increased for any E/N (electric field intensity/gas number density) values greater than 7 Td. These results are compared to other experimental data and an explanation for the temperature dependence, based on the population of upper vibrational states, is presented. © 1979 American Institute of Physics.

Recovery Of Lead From Lead Smelter Mattes, Cheng-Ping Chang

Masters Theses

"A by-product of lead smelting is a matte which consists mostly of lead and copper sulfides. Experiments were conducted to determine the feasibility of removing lead from molten matte by adding iron as a reducing agent. The effectiveness of iron at 1000 and 1100°C was a function of matte composition, but not of temperature except near iron saturation. The lead content of matte could be decreased to as low as 9.0 to 11.6 wt pct (2.3 to 3.0 at. pct) at 1000°C, depending on composition. The effect of oxygen in the matte on lead recovery from iron-saturated mattes was also …

Cadmium In Forest Ecosystems Around Lead Smelters In Missouri, Nord L. Gale, Bobby G. Wixson

Biological Sciences Faculty Research & Creative Works

The development of Missouri's new lead belt within the past decade has provided an excellent opportunity to study the dissemination and effects of heavy metals in a deciduous forest ecosystem. Primary lead smelters, within the new lead belt have been identified as potential sources of cadmium as well as lead, zinc, and copper. Sintering and blast furnace operations tend to produce significant quantities of small particulates highly enriched in cadmium and other heavy metals. At one smelter, samples of stack particulate emissions indicate that as much as 0.21 lb of cadmium may be released to the atmosphere per hour. This …

Film Boiling Of Freon 113, Normal Pentane, Cyclopentane And Benzene From Cylindrical Surfaces At Moderate Pressures, G. J. Capone, Efton Park

Chemical and Biochemical Engineering Faculty Research & Creative Works

An investigation of film boiling heat transfer in saturated pools of liquid Freon 113, normal pentane, cyclopentane and benzene was conducted. The fluids were boiled from copper, cylindrical heat transfer surfaces 0.0762m (3 in) long, and 0.01397,0.01905 and 0.0254m (0.55,0.75 and 1.0 in) in diameter. The data covers a moderate range of pressures up to 1.67 (10)6 N/m2 (242.5 psia). The experimental data are compared with existing film boiling correlations. The existing film boiling correlations were found to be inadequate in predicting heat-transfer coefficients for the conditions of this investigation. © 1979.

Cndo Calculations On The Structure Of A Liquid Sodium Carboxylate-Carboxylic Acid Compound, Beverly Bendiksen, Stig Friberg, Patricia L.M. Plummer

Chemistry Faculty Research & Creative Works

The molecular interactions in a carboxylic acid/sodium carboxylate compound which is a liquid at room temperature were calculated using a CNDO/2 approach. The calculations gave results distinguishing the energy for different conformations in the molecular compound. The maximum binding energy was found for a structure in which the four acids were bridging with a hydrogen bond from the acid OH group to the carboxylate group and the acid carbonyl groups forming a ligand bond to the carboxylate sodium ion. © 1979 Academic Press, Inc.

Plasma Polymerization Of Tetrafluoroethylene. I. Inductive Radio Frequency Discharge, H. Yasuda, N. Morosoff, E. S. Brandt, C. N. Reilley

Chemistry Faculty Research & Creative Works

The plasma polymerization of tetrafluoroethylene in an inductively coupled radio frequency glow discharge, using a flow system, was studied. A simple long tube reactor, with the coupling coil placed at the middle of the tube and gas entrance and exit at the respective ends, was used. Deposition rates and the chemical nature of the polymer (as revealed by ESCA spectra and surface energy studies) are obtained as a function of location in the reactor tube with respect to the coupling coil and of applied energy per unit mass of tetrafluoroethylene (W/FM). It was found that a fluorine poor polymer, containing …

Phase 1 Inspection Report: National Dam Safety Program. Missouri - Kansas City Basin. Binder Lake Dam, Cole County, Missouri, Hoskins-Western-Sonderegger, Inc. Consulting Engineers, Lincoln, Nebraska

Missouri Dam Safety Inspection Reports

This report presents the results of field inspection and evaluation of the Binder Lake Dam.

It was prepared under the National Program of Inspection of Non-Federal Dams.

This dam has been classified as unsafe, non-emergency by the St. Louis District as a result of the application of the following criteria:
1) Spillway will not pass the Probable Maximum Flood.
2) Overtopping could result in dam failure.
3) Dam failure significantly increases the hazard to loss of life downstream.

Phase Equilibria In Aqueous Magnesium Chloride, Sulfate, Chromate And Phosphate Systems, Ladawan Urwongse

Doctoral Dissertations

"In the first part of the present study, which is presented in Paper I, solubility of MgO in aqueous HCl solutions at 23° ± 3°C was measured and combined with analyses of neat magnesium oxychloride cements to construct an equilibrium phase diagram for the system MgO-MgCl₂-H₂O. Invariant liquids in equilibrium with Mg(OH)₂ and 5Mg(OH)₂·MgCl₂·8H₂O (5.1.8), with 5·1·8 and 3Mg(OH)₂·MgCl₂·8H₂O (3·1·8), and with 3·1·8 and MgCl₂·6H₂O were located at 0.8 ± 0.2 MgO, 17.0 ±0.5 MgCl₂; at 1.0 …

Stress-Strain Properties Of Compacted Modified Memphis Loess, Danny Lloyd Kerns

Masters Theses

"A study was made of the stress-strain characteristics of compacted samples of a modified loessial soil obtained near Memphis, Tennessee. The study consisted of compacting samples at a constant water content and at unit weights of 92, 96 and 100 pounds per cubic foot (1470, 1540 and 1600 kg/m³). Triaxial tests were performed on unsaturated compacted specimens to obtain stress-strain-volume change data. These data were used to determine stress-dependent functions for tangent modulus and Poisson's ratio"--Abstract, page ii.

A Planning System For Research Management In A University Environment, Russell Lee Goldammer

Masters Theses

"The research project director at a college or university has few, if any, of the traditional management tools that are available for other forms of management, especially in performing the early, crucial stages of planning. This is particularly distressing since managing a program in this type of environment can be very difficult, due to bureaucratic red tape and interdepartmental concerns. The purpose here is to develop an aid for managers with these problems, for more effective research management in a university environment.

After developing a general model for a typical research project at a university, the Gasification Research On Wood …