Digital Commons Network^™

Dielectric Loss Tangent Extraction Using Two Single-Ended Striplines Of Different Width, Jiangshuai Li, Yuanzhuo Liu, Liang Liu, Shengxuan Xia, Scott Hinaga, Victor Khilkevich

Electrical and Computer Engineering Faculty Research & Creative Works

Frequency-dependent electrical properties of dielectric materials are one of the most important factors for high-speed signal integrity design. Recently a method of accurately measuring the dielectric loss tangent ($\tan \delta$) of differential lines was proposed. By taking into account the ratio between the differential and common mode per-unit-length resistances the surface roughness contribution to the total loss is eliminated and dielectric parameters can be determined. In this article a similar method is applied to a combination of two single-ended lines. To evaluate the accuracy of the extraction, the impact of the de-embedding errors was investigated, which allows to optimize the …

A Segmentation Strategy For Structures With Common Mode Coupling, James Hunter, Shengxuan Xia, Aaron Harmon, Mohamed Z.M. Hamdalla, Ahmed M. Hassan, Victor Khilkevich, Daryl G. Beetner

Electrical and Computer Engineering Faculty Research & Creative Works

The level of electromagnetic coupling to electronic devices can vary widely from one device to another. When considering the induced voltage from an incoming plane wave on printed circuit boards (PCBs) and their attached cable harnesses, there is significant variety in the configuration of the devices that could be seen. This encourages the use of segmentation, so that the components of these devices (PCBs, connectors, and harnesses) can be modeled separately to alleviate simulation burden. This allows for a more flexible model and a 'toolbox' to construct devices with. The goal of this work is to use segmentation to model …

Practical Fixture Design For Passive Intermodulation Tests For Flexible Metallic Contacts, Shengxuan Xia, Yuchu He, Yansheng Wang, Hanfeng Wang, George Mankaruse, Danny Chan, Haicheng Zhou, Warren Lee, Nicholas Mcdonnell, Chulsoon Hwang

Electrical and Computer Engineering Faculty Research & Creative Works

Passive intermodulation (PIM) commonly exists in non-ideal metallic contacts. Since PIM typically represents an extremely low level of nonlinearity, it has not drawn enough attention over the years except for extremely high-power applications such as base stations. However, in recent years, the study on PIM has become essential in universally used consumer electronics design because of the higher requirement on the radio frequency (RF) sensitivity of wireless communications. The metal contacts caused PIM can create the sideband spectrum to interfere with the receiving band in the frequency divide duplex (FDD) mode. Therefore, the study on PIM for the frequently used …

Peec-Based On-Chip Pdn Impedance Modeling Using Layered Green's Function, Chaofeng Li, Biyao Zhao, Bo Pu, Xu Wang, Donghyun Kim, Jun Fan

Electrical and Computer Engineering Faculty Research & Creative Works

This paper presents an impedance model of on-chip power distribution network (PDN), which is an efficient criterion for estimating simultaneous switching noises (SSNs) on 3-D integrated circuit (IC). The impedance of on-chip PDN, including the effect of silicon substrate, is accurately modeled based on partial element equivalent circuit (PEEC) and layered Green's function (LGF). The equivalent circuit model of PDN is extracted based on the physical dimensions and electrical material characteristic of PDN at first. And then the LGF is used to consider the effect of silicon substrate for improving the accuracy of on-chip PDN impedance model. The effectiveness of …

3d Printed Multilayer Microwave Absorber, Wei Zhang, Rui Mi, Victor Khilkevich

Electrical and Computer Engineering Faculty Research & Creative Works

This paper explores the possibility to create 3D printed multilayer electromagnetic absorbers. The proposed design is similar to the thin-film filters used in optics and consists of interleaving high and low permittivity layers. Based on transmission line theory, the multilayer absorber can be designed in a circuit simulator. Analytical equations, circuit simulations, and measurements are used to analyze and validate the designed absorber. Multilayer absorbers based on 3D printed material can be an inexpensive option for engineering usage with great design flexibility and fast fabrication.

A Practical Simulation Flow For Singing Capacitor Based Acoustic Noise Analysis, Xin Yan, Songping Wu, Mingfeng Xue, Chi Kin Benjamin Leung, Daryl G. Beetner, Jianmin Zhang

Electrical and Computer Engineering Faculty Research & Creative Works

Multilayer ceramic capacitors (MLCCs) are widely used in modern electronics. Due to the piezoelectric effect of the ceramic material, however, MLCCs subjected to electrical noise may vibrate and generate acoustic noise, as 'singing'. Acoustic noise can be annoying for users, especially within mobile devices, so it becomes important to perform acoustic noise analysis before a product is released. In this paper, a practical simulation flow for singing capacitor based acoustic noise is presented. The simulation flow and analysis method are developed on Ansys Sherlock and Mechanical. In Ansys Sherlock, local library and Approved Vendor List (AVL) files were used to …

Physics-Based Modeling For Determining Transient Current Flow In Multi-Layer Pcb Pi Designs, Yifan Ding, Matthew S. Doyle, Samuel Connor, Dale Becker, James L. Drewniak

Electrical and Computer Engineering Faculty Research & Creative Works

A physics-based modeling methodology for determining the transient current flow path in multi-layer PI designs is given in this paper using a commercial board with a complicated structure as an example. Board structure analysis is done first to provide a physical basis of post-layout analytical and equivalent circuit modeling. A match of the PDN impedance between commercial tool simulation, post-layout analytical calculation, and the physics-based equivalent circuit modeling was achieved to support the model for the transient simulation. By analyzing the current response in all the vias, a clear representation of transient current flow across all via segments can be …

Identifying Sources Of Conducted Emissions By Measuring The Coherence Function, Xin Yan, Fuwei Ma, Wei Zhang, Kaustav Ghosh, Sameer Walunj, Philippe Sochoux, Victor Khilkevich

Electrical and Computer Engineering Faculty Research & Creative Works

Conducted emissions (CE) is one of the electromagnetic interference (EMI) issues that pose serious compliance problems for electronic devices. For a system with several sources, estimating the contribution of each source to conducted emission at different frequencies can be a challenge. In this article, a coherence function-based signal separation method is presented and validated on two commercial power supply units (PSU). The noise generated by the PSU and measured at the line impedance stabilization network (LISN) port contains two predominantly uncorrelated signals associated with the power factor correction (PFC) and H -bridge/rectifier circuits with unknown contributions at different frequencies. Two …

A New Discontinuous Conduction Mode In A Transformer Coupled High Gain Dc-Dc Converter, Kartikeya J.P. Veeramraju, Jacob Eisen, Joshua L. Rovey, Jonathan W. Kimball

Electrical and Computer Engineering Faculty Research & Creative Works

Electrospray space propulsion thrusters often employ transformer coupled high gain dc-dc converters. These thrusters have a unique load resistance profile that can vary dramatically during operation. Transformer coupled high gain dc-dc converters working in very low power modes can enter a unique discontinuous conduction mode (DCM) caused by a coupling effect between the boost and magnetization inductors in the converter. The transformer magnetization current prevents the boost inductors from discharging properly, which causes premature loss of boost action and higher than expected boost inductor voltages. This mechanism generates abnormally high voltages on the converter's output side, leading to converter and …

Effects Of Vacancies And Electron Temperature On The Electron Phonon Coupling In Cubic Silicon Carbide And Their Connection To The Inelastic Thermal Spike, Salah Al-Smairat

Doctoral Dissertations

“The electron-phonon interaction is an important interaction in many solids as it influences transport phenomena and related quantities such as the electrical and thermal conductivities, especially in nuclear and space applications. The importance of the electron-phonon interaction in primary damage production in 3C-SiC is the subject of this research.

The electron-phonon coupling factor was calculated using a hybrid Density Functional Perturbation Theory - Classical Electron Gas model. The coupling factor was calculated as a function of electron temperature in pristine and defective 3C-SiC, and relaxed defective cells. The electron-phonon coupling is found to depend strongly on the electronic temperature and …

The Utilization And Loss Of Available Energy In Aerospace Systems, Mohammad Abbas

Doctoral Dissertations

“Theoretical principles and analytical methodology for the control volume-based energy availability methodology for aerospace vehicles are developed; applications are made to jet-propelled and rocket-propelled vehicles as well as to stand-alone engine systems. Energy availability utilization characteristics of a modeled turbojet engine are studied across a wide range of operating conditions of throttle setting, flight altitude, and flight Mach number. The method is also extended to consider jet-powered vehicles. Fundamental principles regarding entropy generation and energy availability are developed, including directly linking entropy generation and maximum range and endurance of a powered aircraft. Theory and application of the energy utilization methodology …

Theoretical And Experimental Application Of Neural Networks In Spaceflight Control Systems, Pavel Galchenko

Doctoral Dissertations

“Spaceflight systems can enable advanced mission concepts that can help expand our understanding of the universe. To achieve the objectives of these missions, spaceflight systems typically leverage guidance and control systems to maintain some desired path and/or orientation of their scientific instrumentation. A deep understanding of the natural dynamics of the environment in which these spaceflight systems operate is required to design control systems capable of achieving the desired scientific objectives. However, mitigating strategies are critically important when these dynamics are unknown or poorly understood and/or modelled. This research introduces two neural network methodologies to control the translation and rotation …

Modeling Strategy For Emi Filter And Flyback Transformer, Ruijie He

Doctoral Dissertations

“The switch-mode power supply is key to miniaturizing power adapters. However, the switching nature of the circuit introduces issues in conducted emissions. In a flyback converter, the transformer serves as the path for common mode current flowing from the primary side to the secondary side. Different winding technologies have been invented and implemented to reduce the capacitance between the primary side and the secondary side. But the repeatability of the winding is still poor due to the fluctuations of the winding machine. Thus, the resulting conducted emission has a fluctuation that can lead to failure in the compliance tests. EMI …

Numerical Simulation Study Of Gel Treatment For Conformance Control From Lab To Field, Jianqiao Leng

Doctoral Dissertations

“Gel treatment has been widely applied to control reservoir conformance and thus improve the sweep efficiency of injection fluids. Quite a few numerical simulations have been conducted to investigate the factors impacting gel treatment and assist to optimize treatment design and predict the performance. However, there exists significant barrier between the simulation approaches and lab experiments. In this study, two comprehensive reviews have been conducted to identify the gaps between lab and current simulations for in-situ polymer treatment and preformed particle gel treatment, separately.

Based on the identified gaps, the effect of a few major factors which are very important …

Characterization And Modeling Of Esd Events, Risk And Protection, Jianchi Zhou

Doctoral Dissertations

“The ESD (Electrostatic discharge) failures have been raising critical reliability problems in electronic devices design. However, not all the ESD scenarios have been specified by the IEC standard and the characterizations of the ESD risk for different scenarios are essential to evaluate the ESD robustness of the devices in the real word.

The insulation of plastic enclosures provides protection against ESD to the electronic system inside. However, seams between plastic parts are often unavoidable. Different plastic arrangements are constructed to investigate the spark length and current derivatives and to understand the ESD spark behavior for geometries having spark lengths longer …

Investigation Of The Thermodynamics Of Iron Phosphate Melts And Stability Of Iron Phosphate Glasses: Effects Of Composition And Iron Redox Ratio, Melodie Linda Schmitt

Doctoral Dissertations

“Iron phosphate glasses with Fe/P = 0.33 - 0.67, O/P = 3.0 - 3.5 and Fe²⁺/ΣFe = 0.16- 0.52 were prepared by altering batch compositions and melt conditions. Thermal analyses indicate polyphosphate glasses with intermediate chain lengths are most stable against devitrification. Heterogeneous crystallization occurs on the glass surface and is dependent on iron valence state, particle size, heating rate, temperature and oxygen availability in the atmosphere. Oxidation of ferrous iron on the glass surface occurs at temperatures as low as Tg, and thus crystallization behavior and stability can be altered via post-melt heat treatments. A novel preparation …

Evaluation Of Recrosslinkable Preformed Particle Gel (Rppg) As A Fluid Loss Control Material During Drilling Operations, Mohamed Saad M. Ahdaya

Doctoral Dissertations

"One of the most intense, expensive, and time-consuming problems during drilling operations is the loss of circulation, which could result in several consequences, including wellbore collapse, fluid inflow, formation damage, environmental issues, and nonproductive time. This research aims to evaluate novel materials that can mitigate lost circulation and overcome the limitation of other materials. In this research, a comprehensive evaluation of a re-crosslinkable preformed particle gel (RPPG) has been conducted to determine the extent to which it can be used to control drilling fluid losses during drilling operations. The RPPG consists of swellable gel particles that can self-crosslink to form …

Synthesis And Process Optimization Of Colloidal Unimolecular Polymer, Cup, Particle Formation, And Its Interfacial Surface Tension Behavior, Ashish Zore

Doctoral Dissertations

"Colloidal Unimolecular Polymer (CUP) particles are 3-9 nm size single-chain polymer nanoparticles that are made from amphiphilic acrylic co-polymers using the process of water reduction. The formation of CUP particles was driven by the polymer-polymer interactions being greater than polymer-solvent interactions as well as the charge-charge repulsion due to the increasing dielectric of the medium. CUPs provide a surfactant or additive-free nanoparticle system that was useful for studying the interfacial behavior of pure aqueous nanoparticles using a maximum bubble pressure tensiometer. The equilibrium surface tension shows a dependence on concentration and the charge density of the CUP particle. The equilibrium …

Advances In Control Of Uncertain Dynamical Systems With Optimal And Adaptive Approaches, Meryem Deniz

Doctoral Dissertations

"This research starts with designing optimal control for uncertain systems, adding the adaptive control input to suppress the uncertainty. It then follows with designing the optimal control for state constraint, designing the optimal nonlinear reference model, designing adaptive control to handle state constraint and uncertainty. Finally, it designs the finite-time controller for uncertain multiagent systems.

It is well known that the design of the control algorithm for an uncertain dynamical system is not trivial. Motivated by this standpoint, this study focuses on optimal and adaptive control approaches with stability and performance guarantees for uncertain sole and multiagent dynamical systems. From …

Design Methods For Pressure Relief Well Systems At Dams And Levees, Andrew Keffer

Doctoral Dissertations

"Flood risk reduction structures such as dams and levees are important systems that provide significant benefits to the nation. Relief wells reduce the substratum water pressures that can compromise them via internal erosion. The U.S. Army Corps of Engineers (USACE) analytical method to design relief well systems by calculating discharge and excess head along an infinite line of wells was developed from the 1930s – 1950s. The research presented here increases our understanding of the method’s history and uses analytical and numerical models to improve current infinite and finite well system design practices. The historical development of this method was …

Joining Of Ultra-High Temperature Ceramics To The Same And Refractory Metals Via Fusion Welding, Jecee Jarman

Doctoral Dissertations

"This research focuses on the joining of ultra-high temperature ceramics to either themselves or refractory metals/alloys via fusion welding and the mechanical strength of produced joints. The ceramics studied consisted of compositions within a diboride-carbide-carbide ternary system while metals studied consisted of molybdenum and a molybdenum alloy. SiC-ZrB2-ZrC ceramics on a binary join between pure SiC and the ternary eutectic composition were found to be weldable when SiC content was below ~57.5 vol%. Compositions above 57.5 vol% SiC were unweldable based on pitting and off-gassing behavior. Welded strength of ceramics was ~180-300 MPa in the SiC-ZrB2-ZrC ternary eutectic composition, ~180-220 …

Establishing Pteridine Metabolism In A Breast Cancer Cell Model And Quantification Of Silver Nanoparticle Interactions With Yeast Cells Using Mass Spectrometry, Lindsey Katherine Rasmussen

Doctoral Dissertations

"Recent advances in analytical methods have furthered the quantitative insights that can be gleaned from cellular analyses, with applications in cancer and nanoparticle research. In the first part of the research presented, a recently developed HPLC-MS/MS method was advanced to elucidate pteridine metabolism in an isogenic progressive MCF10A breast cancer cell model. The folate-derived pteridine pathway in breast cells was established by individually dosing cell cultures with folic acid and 15 pteridines. Eight potential pteridine biomarkers in breast cancer cells were identified including pterin and isoxanthopterin, which yielded the first in vitro evidence for the cellular metabolisms behind previously reported …

Processing To Enable Direct-Write Additive Manufacturing Of Ceramics And Ceramic Composites, Austin Martin

Doctoral Dissertations

"This research focuses on the processing of novel feedstocks for and during direct-write additive manufacturing (AM), specifically the direct ink writing (DIW) and Ceramic On-Demand Extrusion (CODE) manufacturing processes, in order to produce ceramic and ceramic-based composite components. Strongly dispersed, concentrated (φ = 0.42), nanoparticle (d₅₀ ~0.3 µm), zirconia (ZrO₂) pastes were used to print densely filled, large continuous volume (≳ 1 cm³) ceramic components. An elastic shear modulus (G’) of 56,000 Pa and yield stresses between 6 and 10 Pa allowed for printed components of 34.5 mm in height over 115 layers without slumping …

Secure And Efficient Information Management In Delay(Disruption) Tolerant Network, Shudip Datta

Doctoral Dissertations

"In environments like international military coalitions on the battlefield or multi-party relief work in a disaster zone, multiple teams are deployed to serve different mission goals by the command-and-control center (CC). They may need to survey damages and send information to the CC for situational awareness and also transfer messages to each other for mission purposes. However, due to the damaged network infrastructure in the emergency, nodes need to relay messages using the store and forward paradigm, also called Delay-tolerant Networks (DTNs). In DTN, the limited bandwidth, energy, and contacts among the nodes, and their interdependency impose several challenges such …

Accuracy Improvement Of Cable Harness Modeling & Analytical Modeling Of Multi-Reflections In High-Speed Signal Channels, Muqi Ouyang

Doctoral Dissertations

"Cable harnesses are widely used in modern vehicles to power electric systems locating at different locations throughout the vehicle and to establish signal channels for data communications between these systems. Generally, a cable harness consists of multiple wires and its geometry can be very complicated, making full-wave modeling and simulation approaches computational resource-intensive. To cut down the computational effort, the hybrid multiconductor transmission-line (MTL) method has been developed, and the generalized MTL (GMTL) method and the multiple scattering (MS) method have been developed to improve the accuracy of the hybrid MTL method. In this research, the convergence issue in the …

The Effect Of Mass Transport On Deposit Quality In Copper Electrowinning, Joseph Bauer

Doctoral Dissertations

"Roughness and nodulation of copper electrodeposits depend strongly on mass transfer conditions of copper ions to the electrode surface. Mass transfer properties in electrowinning electrolytes were first characterized. The effective diffusivity of cupric ion was measured with a rotating disk electrode in CuSO₄-H₂SO₄ electrolytes at temperatures relevant to electrowinning, with and without additives. Adding 20 mg L^-1 of chloride ion increased the measured diffusion coefficient, but commercial smoothing additives had little effect. An empirical formula to predict cupric diffusivity was generated for later use in mass transport modeling.

Boundary layer thickness information for commercial …

Multifunctional Behaviors Of Two-Dimensional Materials And Their Composites, Yanxiao Li

Doctoral Dissertations

"Two-dimensional (2D) materials, including graphene, transition metal carbides or nitrides (TMC/Ns), have rich surface chemistry, superb electrical and mechanical properties. These unique properties make them ideal for multifunctional devices. Among them, we focused on graphene and TMC/Ns (i.e., MXenes), as well as their composites. Unlike the well-known graphene, MXenes, are relatively new and typically synthesized by the selective etching of the “A” layers from the layered carbides and /or nitrides known as MAX phases, which introduce MXenes with rich terminal groups (e.g. -O-, -OH, -F).

During my Ph.D. study, firstly, the adhesive and frictional behaviors, which are related to successful …

Laterally Heterogeneous Seismic Anisotropy Investigated By Shear Wave Splitting Analyses, Yan Jia

Doctoral Dissertations

"Numerous geophysical studies suggest that seismic anisotropy is a nearly ubiquitous property of the Earth’s crust and upper mantle. In this study, we utilize the shear wave splitting technique to investigate the piercing-point-dependent azimuthal anisotropy beneath the northeastern edge of the Sichuan Basin in central China, and the spatial and temporal variations of anisotropy near the 2019 M7.1 Ridgecrest earthquake in California, respectively. A clear back azimuthal dependence of the splitting parameters and the lack of a 90° or 180° periodicity of azimuthal variation in the observed fast orientations provide strong evidence for the existence of piercing-point-dependent anisotropy beneath the …

Groundwater Withdrawal Estimation Using Integrated Remote Sensing Products And Machine Learning, Sayantan Majumdar

Doctoral Dissertations

"The rising demands for water, food, and energy primarily driven by the increasing global population constitute a pressing issue worldwide. Therefore, the water-food-energy nexus plays a substantial role in developing globally applicable sustainable solutions. Recent technological advancements, including the earth observation programs using spaceborne remote sensing platforms, have enabled us to monitor various critical components affecting the globe. Groundwater, which comprises the world's 30% freshwater, is one such key component of the global water resources and supplies nearly half of the global drinking water.

Despite groundwater overdraft in many parts of the world, including the United States (US), there are …

Mantle Flow And Transition Zone Discontinuities Beneath The Carribean Plate: Constraints From Shear Wave Splitting And Receiver Function Analyses, Tu Xue

Doctoral Dissertations

"Azimuthal anisotropy quantified by teleseismic SKS, SKKS, PKS (“XKS”) and local S wave splitting parameters is used to investigate lithospheric deformation and asthenospheric flow beneath the boundary zone of the North American and Caribbean plates and adjacent areas. A total of 4915 XKS and 1202 pairs of local S wave splitting parameters were obtained at 24 broad band seismic stations. The XKS observations can be divided into two groups based on the spatial distribution of the resulting fast polarization orientations. Those observed on the Caribbean Plate are mostly WNW-ESE which are roughly trench-parallel. In contrast, the fast orientations observed on …