Digital Commons Network^™

Dielectric Constant Of Absorbed Water, Reiji Funabiki

University of the Pacific Theses and Dissertations

That the dielectric constant of a substance is one of its important properties is a fact that has been very commonly taken into consideration by electrical engineers in design of apparatus and transmission lines. The importance of the dielectric constant is equally evident to the chemist working in the field of nonaqueous solutions, and Walden and others have spent a great deal of time and energy in attempting to measure the relationship of the dielectric constant of a solvent to its solvent ability, the degree of ionization of a solute dissolved in it, etc. Indeed it has become very common …

The Influence Of A Halowax Oil On The Viscosity Of Lubricating Oil At Various Temperature, Clarence J. Riordan

Bachelors’ Theses

Halowax Oil is used as a.filler in plastic compounds, on wood as an insecticide against termites, and the Petroleum industry finds it a very good valve lubricant in internal combustion engines and a solvent for tarry residues which deposit on combustion chambers. Due to its low viscosity and very low congealing point it would therefore seem logical to investigate this further with the idea of using Halogenated oils as winter lubricants for automobile engines. The work naturally suggested further study, such as its effect on corrosion of steel, aluminum, iron and copper, the flash and fire points, viscosity at various …

General Steps In The Evolution Of The Calculus From The Time Of The Ancients To The Present, Sister Mary Virginia Ssf

Electronic Theses and Dissertations

This thesis, submitted to Xavier University in partial fulfillment of requirements for a Bachelor of Science degree in 1931, traces the historical development of the calculus from ancient Greek mathematics through the early twentieth century. The study is organized chronologically across eight sections. The introduction defines key mathematical terms including calculus, variable, and limit, and situates the calculus as the most powerful instrument of mathematical investigation. The thesis then examines the Method of Exhaustion developed by Greek mathematicians including Antiphon (430 B.C.), Eudoxus (370 B.C.), and Archimedes (225 B.C.), whose summation of infinite series represents the nearest ancient approach to …

The Viscosity Of Liquids, Mary Bede Brielmaier

Bachelors’ Theses

This thesis contains a review of the principal methods of determining the viscosity of liquids, with an experimental investigation of the oscillating disk method.

Iowa Academy Of Science, Jacob W. Swisher

Iowa Academy of Science Documents

Reprinted from the July 1931 issue of the Iowa Journal of History and Politics published by the State Historical Society of Iowa,

Preliminary Construction Of A Photo-Electric Cell Concentrator, Stanley S. Williams

Bachelors Theses and Reports, 1928 - 1970

The separation of the valuable portion from the waste portion of an ore is an individual problem for every ore. However, the various methods for accomplishing this end, more or less classify themselves by the physical properties of the constituents of the ore. Most of the properties of minerals have been utilized in some way or other to affect the separation of the valuable from the invaluable parts. Practically nothing has been done so far with color and luster to attain this purpose.

It is believed that the photo—electric cell could also be used in concentrating a certain class of …

The Effect Of Alternating Current On The Rectifying Properties Of Metallic Salts In Contact With Metals, William Howard Schumaker

Bachelors’ Theses

However much may be said regarding the advantages of direct current, there is little doubt at present, that from the viewpoint of power generation and transmission, alternating current has considerable advantages over direct current. While such is the case, there is, and probably always will be, a need for direct current. According to our present development, this direct current is indispensable in wireless work, radio, and in the laboratory test shops, where it is necessary to work with very sensitive meters, which are inexpensive and easy enough to secure for direct current measurements, but which necessitates an elaborate and costly …

Solubility Curves Of Various Commercial Waxes In Several Organic Solvents, Lawson Joseph Ford

Bachelors’ Theses

The introduction contained herein is- merely meant to acquaint the reader with the common waxes. The subject matter itself has been purposely condensed. For more detailed accounts references are made to well known authorities throughout.

Current Efficiency Of The Commercial Chromium Plating Bath, John Kaczmarowski

Bachelors’ Theses

The subject matter of this thesis deals with the character of the chromium plate, the amount of hydrogen liberated at the cathode, the weight of the chromium deposited, and the cathode efficiency.

This investigation was made for the purpose of aiding .further research work to increase the cathode efficiency of the chromium plating bath. If greater efficiency can be obtained, then, chromium, as nickel, can be plated on small articles in rotating barrels.

A Volumetric Method Of Chromium Determination With Mercurous Nitrate, Gerald W. Lawton

Bachelors’ Theses

Boncyk in his research on potentiometric titrations, made the observation that apparently mercurous nitrate could be used to titrate chromic acid solution. He used potassium iodide as an outside indicator and found that a slight excess of mercurous nitrate gave a gray precipitate with potassium iodide solution. The precipitate seemed to indicate the end point, or the neutralization of the chromic acid; a slight excess of the mercurous nitrate causing the immediate formation of a gray precipitate. Not knowing the exact normality and purity of the solutions used, he could not ascertain whether the gray was the true end point, …

A Study Of The Plating Prohibitive Properties Of Various Separators, Bruno J. Pozorski

Bachelors’ Theses

The problem of this thesis is to study the plating prohibitive properties of the various materials commonly used in the manufacturing of separators, and to indicate which material would be most serviceable and feasible in a separator. At one time positives and negatives were kept not more than 0.25 inches apart, with the idea of reducing the intervening layers of electrolyte, and, therefore, the internal resistance of the cell, as much as possible. It was, however, found that the output could actually be increased by putting the plates at greater distances, the fact being that the larger bulk of solution …

Age Relationships Of Ore Deposits Of Southwestern Montana (A Microscopic Study), Charles R. Trueworthy

Bachelors Theses and Reports, 1928 - 1970

Although considerable work has been undertaken by some prominent geologists, the best known of which is that of Paul Billingsley and J. A. Grimes', in investigating the ore deposits of the Boulder Batholith and surrounding area, there has not been any complete microscopic investigation of these deposits, as a whole, published in the literature. With this in mind it was suggested to the writer by Professor Paul A. Schafer, of the Montana School of Mines, that a microscopic study of the ores of this region would be a worthwhile geologic problem.

It was thought that the mineral association and the …

A Preliminary Study Of The Separation Of The Copper Sulfides From Sphalerite And The Effect Of Certain Reagents On Some Of The Pure Copper Minerals In Synthetic Mixtures, Gailen T. Vandel

Bachelors Theses and Reports, 1928 - 1970

The problem of separating the copper sulfide minerals from sphalerite, in copper - zinc ores, has been a difficult one. This is largely due to the lack of adequate research and the small amount of data obtainable on the behavior of copper and zinc sulfide minerals in flotation circuits.

A Bibliography Of The Theory Of Relativity, Ruth E. Richardson

University of the Pacific Theses and Dissertations

This thesis, a Bibliography of Relativity, has begun with a very meager knowledge of the amount of literature which has been written on the subject of relativity either s explanation or commentary. The project was to 11at all the books and periodical articles written on or about the subject Relativity which are on file in the libraries of the College of the Pacific, University of California and stanford up to and including the year 1920.

Test 185: Rumely Model 6a, Nebraska Tractor Test Lab

Nebraska Tractor Tests

All tractors tested at the Nebraska Tractor Test Laboratory were certified by their manufacturers as being stock model machines, conforming to specifications filed with the application for test. No special or high-test fuels were used except as recommended by the manufacturer as necessary.

All results within the official tractor test report were actually attained in tests and are without correction or allowances for friction, temperature, altitude, etc. The results were initially accomplished with the tractor in charge of skilled operators employed by the University.

Unless otherwise noted, each tractor was apparently in good condition at the end of the testing …

Test 191: Massey-Harris "General Purpose", Nebraska Tractor Test Lab

Nebraska Tractor Tests

All tractors tested at the Nebraska Tractor Test Laboratory were certified by their manufacturers as being stock model machines, conforming to specifications filed with the application for test. No special or high-test fuels were used except as recommended by the manufacturer as necessary.

All results within the official tractor test report were actually attained in tests and are without correction or allowances for friction, temperature, altitude, etc. The results were initially accomplished with the tractor in charge of skilled operators employed by the University.

Unless otherwise noted, each tractor was apparently in good condition at the end of the testing …

Test 195: Cletrac Model 40-30, Nebraska Tractor Test Lab

Nebraska Tractor Tests

All tractors tested at the Nebraska Tractor Test Laboratory were certified by their manufacturers as being stock model machines, conforming to specifications filed with the application for test. No special or high-test fuels were used except as recommended by the manufacturer as necessary.

All results within the official tractor test report were actually attained in tests and are without correction or allowances for friction, temperature, altitude, etc. The results were initially accomplished with the tractor in charge of skilled operators employed by the University.

Unless otherwise noted, each tractor was apparently in good condition at the end of the testing …

Test 186: Bates Steel Mule Model 35, Nebraska Tractor Test Lab

Nebraska Tractor Tests

No abstract provided.

Test 196: Cletrac Model 15, Nebraska Tractor Test Lab

Nebraska Tractor Tests

All tractors tested at the Nebraska Tractor Test Laboratory were certified by their manufacturers as being stock model machines, conforming to specifications filed with the application for test. No special or high-test fuels were used except as recommended by the manufacturer as necessary.

All results within the official tractor test report were actually attained in tests and are without correction or allowances for friction, temperature, altitude, etc. The results were initially accomplished with the tractor in charge of skilled operators employed by the University.

Unless otherwise noted, each tractor was apparently in good condition at the end of the testing …

Test 197: Minneapolis- Moline Universal Model Mt, Nebraska Tractor Test Lab

Nebraska Tractor Tests

All tractors tested at the Nebraska Tractor Test Laboratory were certified by their manufacturers as being stock model machines, conforming to specifications filed with the application for test. No special or high-test fuels were used except as recommended by the manufacturer as necessary.

All results within the official tractor test report were actually attained in tests and are without correction or allowances for friction, temperature, altitude, etc. The results were initially accomplished with the tractor in charge of skilled operators employed by the University.

Unless otherwise noted, each tractor was apparently in good condition at the end of the testing …

Test 194: Mccormick Deering Industrial Model 20, Nebraska Tractor Test Lab

Nebraska Tractor Tests

All tractors tested at the Nebraska Tractor Test Laboratory were certified by their manufacturers as being stock model machines, conforming to specifications filed with the application for test. No special or high-test fuels were used except as recommended by the manufacturer as necessary.

All results within the official tractor test report were actually attained in tests and are without correction or allowances for friction, temperature, altitude, etc. The results were initially accomplished with the tractor in charge of skilled operators employed by the University.

Unless otherwise noted, each tractor was apparently in good condition at the end of the testing …

Test 189: Allis-Chalmers "All Crop", Nebraska Tractor Test Lab

Nebraska Tractor Tests

All tractors tested at the Nebraska Tractor Test Laboratory were certified by their manufacturers as being stock model machines, conforming to specifications filed with the application for test. No special or high-test fuels were used except as recommended by the manufacturer as necessary.

All results within the official tractor test report were actually attained in tests and are without correction or allowances for friction, temperature, altitude, etc. The results were initially accomplished with the tractor in charge of skilled operators employed by the University.

Unless otherwise noted, each tractor was apparently in good condition at the end of the testing …

Test 190: John Deere Gp, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF TEST REPORT: John Deere GP

TEST A: The manufacturer's representative operates the tractor for a minimum of 12 hours using light to heavy drawbar loads in each gear.

This serves as a period for limber up, general observation and adjustments. Adjustments that are permissible include valve tappet clearance, breaker ,point gap, spark plug gaps, clutch and others of a similar nature. No new parts or accessories can be installed without having mention made of it in the report. No data' are recorded during this preliminary run except the time that the engine is operated.

BELT HORSEPOWER TESTS

TEST …

Test 187: Bates Steel Mule Model 45, Nebraska Tractor Test Lab

Nebraska Tractor Tests

All tractors tested at the Nebraska Tractor Test Laboratory were certified by their manufacturers as being stock model machines, conforming to specifications filed with the application for test. No special or high-test fuels were used except as recommended by the manufacturer as necessary.

All results within the official tractor test report were actually attained in tests and are without correction or allowances for friction, temperature, altitude, etc. The results were initially accomplished with the tractor in charge of skilled operators employed by the University.

Unless otherwise noted, each tractor was apparently in good condition at the end of the testing …

Test 192: Bradley "General Purpose", Nebraska Tractor Test Lab

Nebraska Tractor Tests

All tractors tested at the Nebraska Tractor Test Laboratory were certified by their manufacturers as being stock model machines, conforming to specifications filed with the application for test. No special or high-test fuels were used except as recommended by the manufacturer as necessary.

All results within the official tractor test report were actually attained in tests and are without correction or allowances for friction, temperature, altitude, etc. The results were initially accomplished with the tractor in charge of skilled operators employed by the University.

Unless otherwise noted, each tractor was apparently in good condition at the end of the testing …

Test 193: Allis Chalmers Model Ek, Nebraska Tractor Test Lab

Nebraska Tractor Tests

All tractors tested at the Nebraska Tractor Test Laboratory were certified by their manufacturers as being stock model machines, conforming to specifications filed with the application for test. No special or high-test fuels were used except as recommended by the manufacturer as necessary.

All results within the official tractor test report were actually attained in tests and are without correction or allowances for friction, temperature, altitude, etc. The results were initially accomplished with the tractor in charge of skilled operators employed by the University.

Unless otherwise noted, each tractor was apparently in good condition at the end of the testing …

Test 198: Mccormick-Deering Farmall "F-30", Nebraska Tractor Test Lab

Nebraska Tractor Tests

All tractors tested at the Nebraska Tractor Test Laboratory were certified by their manufacturers as being stock model machines, conforming to specifications filed with the application for test. No special or high-test fuels were used except as recommended by the manufacturer as necessary.

All results within the official tractor test report were actually attained in tests and are without correction or allowances for friction, temperature, altitude, etc. The results were initially accomplished with the tractor in charge of skilled operators employed by the University.

Unless otherwise noted, each tractor was apparently in good condition at the end of the testing …

Test 199: Mccormick-Deering "Tractractor", Nebraska Tractor Test Lab

Nebraska Tractor Tests

All tractors tested at the Nebraska Tractor Test Laboratory were certified by their manufacturers as being stock model machines, conforming to specifications filed with the application for test. No special or high-test fuels were used except as recommended by the manufacturer as necessary.

All results within the official tractor test report were actually attained in tests and are without correction or allowances for friction, temperature, altitude, etc. The results were initially accomplished with the tractor in charge of skilled operators employed by the University.

Unless otherwise noted, each tractor was apparently in good condition at the end of the testing …

A Study Of An Objective Placement Examination For Sectioning College Physics Classes, John Milton Willson

Masters Theses

"For several years the Department of Physics of the Missouri School of Mines has practiced sectioning of its classes in general physics. The aim has been to segregate in one section the students of superior ability, giving them a course including both the fundamentals of physics and their applications in engineering. The remainder are given a course in fundamentals without placing so much stress upon the applications...Another criterion used to supplement the first-year grade record is the student's score on the Iowa Placement Examinations. The physics examination consists of two parts, the Training Series and the Aptitude Series. These examinations …

Some Results Of Magnetometric Surveying In Missouri, John Gustave Grohskopf

Masters Theses

"This thesis describes the results of a series of magnetic surveys carried on in the state of Missouri. The financial assistance required for the work was granted in the form of a fellowship to the author by the Industrial Club of the Industrial Bureau of St. Louis; Mr. George S. Smith, Director. Since the progress of any industrial center is accelerated by the mineral resources contiguous to it, the Industrial Club believed that further research upon known and also undeveloped mineral deposits might result in the development of them. It was decided that geophysical methods of research might show greater …