Digital Commons Network^™

Test 236: John Deere D, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF TEST REPORT: John Deere D

TEST A: The manufacturer's representative operates the tractor for a minimum of 12 hours using light to heavy drawbar loads in each gear.

This serves as a period for limber up, general observation and adjustments. Adjustments that are permissible include valve tappet clearance, breaker ,point gap, spark plug gaps, clutch and others of a similar nature. No new parts or accessories can be installed without having mention made of it in the report. No data' are recorded during this preliminary run except the time that the engine is operated.

BELT HORSEPOWER TESTS

TEST …

The Thiem Method For Determining Permeability Of Water-Bearing Materials, L. K. Wenzel

Conservation and Survey Division: Faculty and Staff Publications

No abstract provided.

Some Contributions To Iodometric Technique, Justin Kimber Dyche

University of the Pacific Theses and Dissertations

Analysis is a very important branch of chemistry, for it is such a practical part of the science. Analysis is itself divided into two parts. Qualitative analysis discovers what things are present in the material in question. Quantitative analysis then determines how much of each ingredient is present. This thesis considers a limited section of quantitative analysis.

This thesis deals with the use of iodine in volumetric analysis, which is called either iodimetry or iodometry. In this type of analysis, the iodine is used in solution and reacts with some other material, also in solution, and takes up electrons. That …

Investigations Concerning Bentonite Deposits Near Ramsay, Montana, Anton A. Anjel, John F. Sullivan

Bachelors Theses and Reports, 1928 - 1970

The purpose of Part I of this report is to determine the origin of the bentonite deposits, also to locate them with reference to section corners in the vicinity and to determine their extent.

The field work for this report was done in the fall of 1933 and during the spring of 1934. The roads, geologic contacts, and culture in general were mapped with the use of an open sight alidade and plane table. Distances were determined on the roads by the speedometer on the automo­bile; the detailed survey in the immediate vicinity of the deposits was done with use …

Supergene Enrichment Of Silver Ores With Special Reference To Those From Neihart, Montana., Thomas Walker Page

Bachelors Theses and Reports, 1928 - 1970

In the development of a technique it was necessary to learn the fundamentals of ore microscopy as applied to the various minerals of silver, which included the use of reflected polarized light, etch reactions, micro­chemical analysis, and sight recognition of mineral. In addition it was necessary to become familiar with the accepted criteria of sequence, replacement, and other textural phenomena.

Geology And Ore Deposits Of The Butte-Highland Gold Mine., Stockton Veazey Jr.

Bachelors Theses and Reports, 1928 - 1970

The Butte-Highland mine is situated at the head of Basin Creek, in the Highland mining district, Silver Bow County, about 14 miles south of Butte. The tunnel portal and present surface plant are at an elevation of about 7350 feet above sea level, facing westward across the head of Basin Creek valley. The "ghost" mining town of Highland lies a mile to the east, near the forks of Fish Creek. Access to the mine is obtained at present from Beaudine's siding, 12 miles west. The property may also be reached, with difficulty, over poor roads from Limekiln hill, or from …

Preliminary Floatation Tests On The Beneficiation Of A Low-Grade Montana Bituminous Coal., William Packwood Given

Bachelors Theses and Reports, 1928 - 1970

Coal is an aggregation of vegetal matter with varying small amounts of mineral and animal matter which have been so changed by the processes of sedimentation, decay and metamorphism that it has become a dense, dark, combustible substance. It occurs in beds varying in thickness from one foot or less to over 300 feet. The horizontal extent of a bed is sometimes continuous over an area as large as the State of Montana.

Auriferous Tertiary Gravels Near Rocker, In Silver Bow County, Montana, William C. Mclaughlin

Bachelors Theses and Reports, 1928 - 1970

Between the villages of Rocker and Silver Bow, in south­western Montana, are found an interesting group of placers. Gold occurs in Tertiary gravel beds that are interstratified with beds of rhyolitic volcanic ash. With the aid of a plane table and open-sight alidade, a small portion of the lake-bed area near Rocker was mapped; all distances were paced, but numerous checks assure a fairly accurate map.

The Age-Hardening Of Duralumin, Allison Richard Dyer

Bachelors Theses and Reports, 1928 - 1970

The development of wrought alloys of aluminum to which high strength and ductility can be imparted by heat treatment began with the work of Wilm and Claesser in Germany, 1905­-1911. During this time an alloy was developed which was later commercially produced in that country under the tradename of duralumin. The need for strong, light alloys for aircraft during the World War greatly hastened the development of duralumin.

Ammoniacal Sulphate Leach Of Ananconda Zinc Calcine Recovery Of The Zinc By Electrolysis., Authur Jewett Bovee Jr.

Bachelors Theses and Reports, 1928 - 1970

Zinc is produced from ores by two general methods, distillation and electrolysis.

The general principles involved in the electrolytic zinc process of today were known as far back as 1880. Difficulties encountered in purifying the solution for electrolysis and lack of suitable mechanical apparatus were the main reasons that such a long time elapsed before the process was used to produce zinc in commercial quantities.

Precipitation Of Gold, Silver, And Copper From Cyanide Solutions On Activated Charcoal., Rayworth Francis Howe

Bachelors Theses and Reports, 1928 - 1970

Charcoal has been known for a considerable length of time to have the property of recovering gold, silver, and copper from cyanide solutions of these metals. Quantita­tive data that may shed light on the mechanism of the re­moval of these metals is very limited except that char­coal in a form known as activated has the power to abstract gold and silver in considerable quantities from the above solutions.

The Effect Of Impurities On The Electrodeposition Of Zinc From Zinc Sulfate Solution Containing Antimony., Emmitt L. Klebba

Bachelors Theses and Reports, 1928 - 1970

It has been proven by research and years of experience, that before electrolytic zinc is possible, the electrolyte, as zinc sulfate solution must be prepared as pure as is economical. In other words, the ideal electrolyte must only be a solution of one metal - zinc. Every other metal and carbon must be excluded if good recovery and a firm deposit is to be obtained.

Alloys Of Lead And Tellurium, Ettore A. Peretti

Bachelors Theses and Reports, 1928 - 1970

Prior to the last few years little practical use was made of the element tellurium, which is obtained from gold and silver tellurides and from the slimes of electro­lytic copper refineries. Lately, however, more study has been made of its properties when alloyed with other metals. It was the purpose of this thesis to study the effects of the addition of tellurium to lead, particularly in small amounts.

Conodonts From The Quadrant Shales Of Montana, Don R. Cubbage

Bachelors Theses and Reports, 1928 - 1970

Conodonts have not been known to exist in Montana prior to the discovery of the specimens discussed and described in this paper. With this fact in mind, the author has endeavored to correlate the species of seven genera found in the Quadrant formation of Montana with similar micro-organisms from other North American areas.

The Sine-Function, Audrey Siehr

Bachelors’ Theses

Since the sine function is one of the most important elements of that phase of mathematics known as Trigonometry, it is only proper that we pause a moment for a short explanation of that subject. Trigonometry originated with the Greeks as the name itself implies. It was derived from the two Greek words trlgonon, meaning triangle; and metria, meaning measure. Trigonometry, then, dealt with problems related to measuring triangles.

The Effect Of Halowax 1012, 1013 & 1014 On The Melting Points Of Various Waxes, Louis Henry Kroening

Bachelors’ Theses

This thesis is concerned with the melting points of various waxes and the effect of Halowax 1012, 1013 and 1014 upon their physical constants. Interest in this problem was aroused "by the fact that Halowax as shown by Nathan Smith in his thesis, "The Effect of Halowax Upon Lubricating Oils and Greases”, decreases the viscosity of oils. Since lubricating oils contain waxes it is logical to expect that this decrease in viscosity is due to the lowering of the melting point of the waxes present. It was to investigate the truth of this assumption that this work was begun.

A Study Of Melting Points Of Various Ternary Mixtures Of Waxes, Leonard Anthony Veranth

Bachelors’ Theses

The work undertaken in this thesis is a continuation of the work done by George John Hable entitled, "A Study of Melting Points of Various Binary Mixtures of Waxes". In the present work, the melting points of ternary mixtures of waxes is studied. The experimental work is presented in the form of graphs so that the reader is afforded a better representation and clearer conception of the work done and the results obtained.

A Contribution To The Preparation Of Synthetic Rubber From Butadiene. Ii., Joseph Patrick Iding

Bachelors’ Theses

Since the World War, the production of synthetic rubber has become the problem not only of the laboratory, but of commerce as well. Several factors demanded this research.

In the first place, the World War made the dependence of countries on each other strikingly evident in several ways, one of which was the need for rubber by great nations whose situations prohibited the planting of the rubber tree and consequently put them under obligation to other countries for their supply.

And now in the last few years this demand for rubber has been increased enormously, through the increased production of …

Roasting And Leaching Bulk Copper-Zinc Sulfide Concentrates With The Subsequent Recovery Of The Metals By Electrolysis, Carl Wesley Sawyer

Bachelors Theses and Reports, 1928 - 1970

The aim of this research was to investigate the possibilities of roasting and leaching a bulk copper-zinc sulfide concentrate, and the subsequent separation of the metals from the leach solution by electro­lytic deposition.

The Equilibrium Relations Of Nickel Sulfide With Copper And Sodium Sulfides, Walter A. Hamilton

Bachelors Theses and Reports, 1928 - 1970

The equilibrium relations of many of the metallic sulfides have long been a source of scientific and commer­cial interest, of particular interest, are the sulfides of nickel and copper, since the economic recovery of both of these useful metals, from their ores, involves the formation of a sulfide at some stage of the operations.

Effect Of Manganese And Arsenic Upon Current Efficiency In The Deposition Of Zinc From Zinc Sulphate Solution, Justin Kelly

Bachelors Theses and Reports, 1928 - 1970

Throughout the entire experiment the electrolysis were conducted in an eight-hundred cubic centimeter beaker. An excellent circulation of the solution was assured by means of an electric stirrer, vigorous gas evolution from the anodes, and by means of a regulated feed-discharge system. By means of this balance, solution of the same impurity concentration as that of the electrolyte was fed in the cell just as fast as the discharge was syphoned out.

Test 226: Caterpiller Model 22, Nebraska Tractor Test Lab

Nebraska Tractor Tests

All tractors tested at the Nebraska Tractor Test Laboratory were certified by their manufacturers as being stock model machines, conforming to specifications filed with the application for test. No special or high-test fuels were used except as recommended by the manufacturer as necessary.

All results within the official tractor test report were actually attained in tests and are without correction or allowances for friction, temperature, altitude, etc. The results were initially accomplished with the tractor in charge of skilled operators employed by the University.

Unless otherwise noted, each tractor was apparently in good condition at the end of the testing …

Test 221: Mccormick Deering Farmall F-20, Nebraska Tractor Test Lab

Nebraska Tractor Tests

No abstract provided.

Test 222: John Deere A, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF TEST REPORT: John Deere A

TEST A: The manufacturer's representative operates the tractor for a minimum of 12 hours using light to heavy drawbar loads in each gear.

This serves as a period for limber up, general observation and adjustments. Adjustments that are permissible include valve tappet clearance, breaker ,point gap, spark plug gaps, clutch and others of a similar nature. No new parts or accessories can be installed without having mention made of it in the report. No data' are recorded during this preliminary run except the time that the engine is operated.

BELT HORSEPOWER TESTS

TEST …

Test 223: Allis-Chalmers Model Wc, Nebraska Tractor Test Lab

Nebraska Tractor Tests

All tractors tested at the Nebraska Tractor Test Laboratory were certified by their manufacturers as being stock model machines, conforming to specifications filed with the application for test. No special or high-test fuels were used except as recommended by the manufacturer as necessary.

All results within the official tractor test report were actually attained in tests and are without correction or allowances for friction, temperature, altitude, etc. The results were initially accomplished with the tractor in charge of skilled operators employed by the University.

Unless otherwise noted, each tractor was apparently in good condition at the end of the testing …

Test 228: Caterpiller Model 22, Nebraska Tractor Test Lab

Nebraska Tractor Tests

All tractors tested at the Nebraska Tractor Test Laboratory were certified by their manufacturers as being stock model machines, conforming to specifications filed with the application for test. No special or high-test fuels were used except as recommended by the manufacturer as necessary.

All results within the official tractor test report were actually attained in tests and are without correction or allowances for friction, temperature, altitude, etc. The results were initially accomplished with the tractor in charge of skilled operators employed by the University.

Unless otherwise noted, each tractor was apparently in good condition at the end of the testing …

Test 225: Caterpiller Model R-2, Nebraska Tractor Test Lab

Nebraska Tractor Tests

All tractors tested at the Nebraska Tractor Test Laboratory were certified by their manufacturers as being stock model machines, conforming to specifications filed with the application for test. No special or high-test fuels were used except as recommended by the manufacturer as necessary.

All results within the official tractor test report were actually attained in tests and are without correction or allowances for friction, temperature, altitude, etc. The results were initially accomplished with the tractor in charge of skilled operators employed by the University.

Unless otherwise noted, each tractor was apparently in good condition at the end of the testing …

Test 231: Mccormick-Deering "W-12" (Gasoline), Nebraska Tractor Test Lab

Nebraska Tractor Tests

All tractors tested at the Nebraska Tractor Test Laboratory were certified by their manufacturers as being stock model machines, conforming to specifications filed with the application for test. No special or high-test fuels were used except as recommended by the manufacturer as necessary.

All results within the official tractor test report were actually attained in tests and are without correction or allowances for friction, temperature, altitude, etc. The results were initially accomplished with the tractor in charge of skilled operators employed by the University.

Unless otherwise noted, each tractor was apparently in good condition at the end of the testing …

Test 227: Caterpiller Model R3, Nebraska Tractor Test Lab

Nebraska Tractor Tests

All tractors tested at the Nebraska Tractor Test Laboratory were certified by their manufacturers as being stock model machines, conforming to specifications filed with the application for test. No special or high-test fuels were used except as recommended by the manufacturer as necessary.

All results within the official tractor test report were actually attained in tests and are without correction or allowances for friction, temperature, altitude, etc. The results were initially accomplished with the tractor in charge of skilled operators employed by the University.

Unless otherwise noted, each tractor was apparently in good condition at the end of the testing …

Test 224: Caterpiller Model R-5, Nebraska Tractor Test Lab

Nebraska Tractor Tests

All tractors tested at the Nebraska Tractor Test Laboratory were certified by their manufacturers as being stock model machines, conforming to specifications filed with the application for test. No special or high-test fuels were used except as recommended by the manufacturer as necessary.

All results within the official tractor test report were actually attained in tests and are without correction or allowances for friction, temperature, altitude, etc. The results were initially accomplished with the tractor in charge of skilled operators employed by the University.

Unless otherwise noted, each tractor was apparently in good condition at the end of the testing …