Digital Commons Network^™

Heat Transfer Through A Honeycomb Sandwich Panel, Jayantilal J. Darji

Masters Theses

"Progress brought about by human ingenuity and technological developments has been always accompanied by fresh problems, the successful solution of which enables still further progress.

The recent developments in space exploration and exploitations are astounding. The coming years are likely to bring forth many remarkable achievements. Except for several engineering problems encountered with these developments the pace of progress is to study the heat transfer from honeycomb sandwich panels as an outer skin of high performance flight vehicles. The quantity of heat transferred through the panel is important in study of such vehicles, and methods or equations for determining this …

Experimental Stress Analysis Of Bolts In A Flange Coupling, Bansidhar Shah

Masters Theses

"This thesis deals with the strength of a bolted joint which is subjected to tensile and bending loads. The purpose of this investigation was to derive expressions for the stresses developed in the bolts and the load producing separation of the joint.

A laboratory study of a flange coupling was made and the behaviour of flange bolts under different clamping forces was studied in tension and bending tests. The strain in the bolt was measured by mounting the strain gages on the shank of the bolt. From this, a graph of applied load versus strain in the bolt was plotted. …

A Parametric Study Of The Heat Transfer Characteristics Of A Moving Band Heat Exchanger, Larry Hyde Brim

Theses and Dissertations

In recent years much attention has been devoted to the development of efficient heat exchangers. The regenerative or moving matrix heat exchanger is one type which has been considered. Most regenerative heat exchangers use one of the conventional types of high area matrices mounted in a drum or disk in such a manner that it can be moved in a continuous cycle from a cold fluid stream to a hot fluid stream and back again. A rather different approach to the design of a regenerative heat exchanger which has been patented in this country is a set of flexible moving …

Stress Analysis Of An Infinite Cylinder With An Irregular Shaped Cavity Using Complex Variable Techniques, Gerald H. Lindsey

Theses and Dissertations

The advancement of modern technology has brought with It a demand upon the engineer for more thorough analysis techniques. This has been precipitated by the advent of missiles and space-craft that do not permit regular inspections to determine causes of failure, crack propagation, design weaknesses, etc. Thus, a more complete analytical work must be performed to facilitate a foreknowledge of reaction and performance of a particular design to its environment.

A Literature Review Covering The Effect Of Residual Stresses On Fatigue Strength Of Steel, Clarence A. Calder

Theses and Dissertations

Fatigue fracture usually is defined as the failure of a part at a stress below its breaking stress due to repetitive loading conditions. It is now a well known fact that a part, designed for a maximum stress well below the yield point of the material, may be very apt to fail under cyclic loading conditions over a period of time. The metal appears to "wear out" after a time just like humans do and fatigue failure occurs. Metal fatigue may be contrasted to animal fatigue in that l) its detection before the latter stages is normally difficult if not …

Experimental Investigation Of The Interaction Of An Oblique Shock Wave With A Turbulent Boundary Layer, Amado Arthur Trujillo

Mechanical Engineering ETDs

The purpose of the investigation was to accurately describe the interaction of a shock wave and a turbulent boundary layer based upon the measurement and subsequent analysis of both static and impact pressure throughout the interaction region.

A Study Of Temperature Measurement Precision In Debye-Scherrer Specimens During High Temperature X-Ray Diffraction Measurement Of Thermal Expansion, Roy Glenn Merryman

Mechanical Engineering ETDs

The literature cited covers a comprehensive survey on temperature measurement methods in thermal expansion determination utilizing X-ray diffraction from 1921 through 1961 and a compilation of all published data on the thermal expansion of gold from 1916 through 1960 and magnesium oxide from 1906 through 1961. References for comparison of the MgO results with those of the Bureau of Mines Interlaboratory Program of Thermal Expansion Measurements on MgO are also presented. The literature on temperature measurement was limited to those articles featuring camera design or temperature conditions, since to examine publications on all phases of thermal expansion was found to …

Determination Of Thermal Stresses At Interior Points, Siegfried Thunborg Jr.

Mechanical Engineering ETDs

Existing theory was used to determine the thermal stresses and strains throughout a long thick walled cylinder under equilibrium thermal conditions when the thermal gra­dient through the wall is dependent on radial position only.

A thick walled cylindrical model, made of a plastic material, was constructed and strain gages were imbedded in and mounted on the cylinder to determine strains at interior and surface locations. The cylinder was subjected to equi­librium and transient thermal conditions and thermal strains were measured. In the equilibrium thermal condition the measured strains were compared with those predicted by theory.

The results show that imbedded …

Radial Dislocations In Plane Stress., William J. Sieger

Mechanical Engineering ETDs

The elastic dislocation theory was used to obtain stress potentials for the dual dislocation problem. These solutions give the stress field for an infinite plane region containing a centrally located circular hole with two radial dislocations originating from opposite sides of the hole and extending into the region along a line perpendicular to the axis of applied load. Solutions were obtained for both the case of a linear dislocation relation along the cuts and for a parabolic relation.

The Aerodynamic Drag Of Spheres, Leon Rouzelle Scott

Theses and Dissertations

A literature survey was conducted to determine the factors which affect aerodynamic drag of spheres. Graphs are presented which show the effect of each variable where such information was available. Equipment was designed and built for the purpose of studying the effects of acceleration on the aerodynamic drag of spheres. Special emphasis was placed on the measurement and control of each of the other variables which can affect the drag. Tests were conducted using large spheres in air and water to show that the method presented can produce a valid determination of the drag coefficients. The numerical values of the …

Plastic Models For The Study Of Thermal Stresses, Carl W. Theisen

Mechanical Engineering ETDs

The purpose of this thesis was to determine and evaluate an experimental method for accurately measuring thermal stresses in structural shapes subjected to large transient thermal gradients, without introducing the problems of high temperature instrumentation, or expensive and elaborate test facilities. Most experimental methods consist of mounting high temperature strain gages on the prototype or model of the metal structure to be evaluated, thermal shocking the structure and then recording the accompanying strains. This method is used quite extensively in the aircraft field, and in others, where the effects of thermal stresses must be considered. However, problems are encountered when …

The Development Of A Static Pressure Probe For The Interaction Region Of Shock Waves And Boundary Layers, John Rode

Mechanical Engineering ETDs

The purpose of this investigation was to develop a static pressure probe for measuring static pressures in the region of interaction of a shock wave and a boundary layer. Requirements of such a probe are: small size to permit measurement of pressure variations within the thin boundary layer, pressure coefficient close to unity to permit precise static pressure measurements in regions of unknown and varying velocity and proper response to large pressure gradients.

Irrigating Dry Season Crops In The Ord Valley : How To Prepare Land For Sowing, D F. Beech

Journal of the Department of Agriculture, Western Australia, Series 4

THE best way to grow dry season crops of safflower, linseed and rapeseed under irrigation in the Ord Valley is by sowing on to broad flat ridges, separated by small furrows 3 ft. 6 in. apart.

This system of sowing is called the "corrugation" method.

The Effects Of Tillage Implements On Cereal Yields, H M. Fisher

Journal of the Department of Agriculture, Western Australia, Series 4

Careful soil preparation is essential for cereal crops grown without fallow on clover ley land.

Crops give better yields where the land is broken up with a mouldboard or disc plough rather than a scarifier or similar machine.

The implements differ appreciably in their capacity to control weed growth and this is largely responsible for variations in cereal yields. "Takeall" disease is reduced by efficient weed control.

A Modified Copper Hot Water System, F J. Fielder

Journal of the Department of Agriculture, Western Australia, Series 4

A good supply of hot and boiling water for cleansing and sterilising utensils is essential for hygienic milk production.

Dairy Instructor F. Fielder, M.D.D., describes an efficient and economical modification of a copper hot water system for this purpose.

SINGLE copper units of 14 or 16 gallon capacity to supply hot and boiling water for the dairy are no longer good enough for most dairy farms.

Australian Tractor Tests : International A554d : Report On Test No. 36 (Farmers' Edition), G H. Vasey, W. F. Baillie

Journal of the Department of Agriculture, Western Australia, Series 4

THIS Report is taken from the full Technical Report No. 36; results are shown here in briefer form: fuller explanations are added.

Values quoted may be rounded out to two instead of three significant figures; to this extent the values may differ slightly but not significantly from those shown in the Technical Report.

Check Your Milking Machine, T Pavy

Journal of the Department of Agriculture, Western Australia, Series 4

MILKING machine efficiency testing carried out by officers of the Department of Agriculture's Dairying Division have shown that many machines are not up to standard.

One reason for this is that farmers do not check their machines regularly.

The Importance Of Rapid And Complete Milking, K Needham, W. G. Robinson

Journal of the Department of Agriculture, Western Australia, Series 4

COMPLETE withdrawal of milk from the udder as quickly as possible after the process of "let-down" has started, is an essential in good milking; management.

Development Of A Simple Bar Method Thermal Conductivity Test, V. J. Flanigan

Masters Theses

"A linear flow bar method type apparatus was set up for finding thermal conductivities by comparison techniques. Comparison technique consist of using a standard specimen where the thermal conductivity is known and comparing it to the unknown specimens to find their conductivity. Apparatus of this type usually uses thermocouples for the required temperature measurements, but thermistors were used in this experiment. The thermistors used required calibration to measure accurate temperatures and this was accomplished by using the known temperatures of the changes of state of some common materials. Five alloys were used to evaluate the method: SAE 1020 steel, gray …

Refrigeration Heat Transfer Characteristics Of An Artificially Cooled Trout Pond, Richard G. Murray

Masters Theses

"In many locations natural summer lake and pond temperatures are too great for the practical production of trout for fishing purposes.

The purpose of this thesis is to investigate the refrigeration capacity required to maintain a pond of water at a temperature that provides a healthful environment for trout.

The over-all refrigeration load for this application was sub-divided into four categories; conduction, convection, evaporation and radiation. Each type was solved by analytical means using suitable boundary conditions and simplifications. It was necessary to determine one boundary condition for the conduction heat transfer by an empirical method.

The results of this …

A Study Of Heat Transfer Coefficients On Cylindrical Pipe In Turbulent Flow, Dennie Lee Adkins

Masters Theses

"This thesis represents a study of the effects of turbulent motion on heat transfer coefficients on cylindrical pipe.

The turbulent motion was created by cutting transverse slots in a spiral configuration along the pipe length.

An induction heater was used for the heat source and water as the cooling medium. The water was conducted over the pipe surface and through the slots.

This caused the laminar layer along the pipe surface to be broken up and an increase in the heat transfer coefficient was experienced.

The main objective of this test was to find if a relation existed between the …

Test 825: International 606 (Gasoline), Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF TEST REPORT GENERAL CONDITIONS East tractor is a production model equipped for common usage. Power consuming accessories can be disconnected only when it is convenient for the operator to do so in practice. Additional weight can be added as ballast if the manufacturer regularly supplies it for sale. The static tire loads and the inflation pressures muse conform to recommendations in the Tire Standards published by the Society of Automotive Engineers. PREPARATION FOR PERFORMANCE RUNS The engine crank case is drained and refilled with a measured amount of new oil conforming to specifications in the operator’s manual. The …

Test 829: John Deere 2010 C Gasoline, Nebraska Tractor Test Lab

Nebraska Tractor Tests

No abstract provided.

Test 830: John Deere 2010 C Diesel, Nebraska Tractor Test Lab

Nebraska Tractor Tests

No abstract provided.

Advertising Brochure: 1962 Ford 600, 800, 2000 - 4000 Series, Nebraska Tractor Test Lab

Nebraska Tractor Tests

No abstract provided.

Advertisting Brochure: Ford Industrial Tractors, Nebraska Tractor Test Lab

Nebraska Tractor Tests

No abstract provided.

Test 824: Oliver 1900 Series B Diesel, Nebraska Tractor Test Lab

Nebraska Tractor Tests

No abstract provided.

Test 831: Oliver 1800 Diesel, Nebraska Tractor Test Lab

Nebraska Tractor Tests

No abstract provided.

Test 832: Oliver 1800 Diesel 4wd, Nebraska Tractor Test Lab

Nebraska Tractor Tests

No abstract provided.

Test 809: Nuffield 460 (Diesel), Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF TEST REPORT GENERAL CONDITIONS East tractor is a production model equipped for common usage. Power consuming accessories can be disconnected only when it is convenient for the operator to do so in practice. Additional weight can be added as ballast if the manufacturer regularly supplies it for sale. The static tire loads and the inflation pressures muse conform to recommendations in the Tire Standards published by the Society of Automotive Engineers. PREPARATION FOR PERFORMANCE RUNS The engine crank case is drained and refilled with a measured amount of new oil conforming to specifications in the operator’s manual. The …