Digital Commons Network^™

The Effects Of Granular Size On The Thermal Conductivity Of Sand, Kanubhai M. Patel

Masters Theses

"The thermal conductivity of granular materials can be determined by the Thomas method. This method was used here to determine the effects of granular size on the thermal conductivity of sand. A river sand was secured and screened. The sand retained between the Tyler Standard Screen Scale, mesh 10 and 14, 14 and 28, 28 and 40, 40 and 48, 48 and 60, and below mesh 60, was used for tests.

The thermal conductivity for the above six samples obtained by the author coincide fairly well with published data.

It is reported in the International Critical Tables that the thermal …

The Design, Construction, And Calibration Of An Angular Accelerameter., Walter Earl Palm

Masters Theses

"The purpose of this work was to design, construct, and calibrate an angular accelerometer for continuous operation. The design uses four symmetrically placed springs connecting a ring and hub. Strain gages are mounted on the springs in a Wheatstone bridge arrangement. When the entire unit is subjected to an angular acceleration, the ring deflects causing an output voltage. This voltage is proportional to the deflection which is shown to be a function of the angular acceleration. The accelerometer was constructed to operate at frequencies up to 120 cps. The calibration was accomplished by using a simple harmonic motion input"-- Abstract, …

The Design, Construction, And Evaluation Of A Vortex Stabilized Plasma Generator, Ronald Ray Williams

Masters Theses

“This report presents the design, construction, and evaluation of a vortex stabilized arc plasma generation facility operating on argon.

The facility consisted of five basic systems; the plasma genera- tor, the electrical power system, the argon flow system, the cooling system, and instrumentation.

The facility was designed to meet four general requirements; stable arc operation, low electrode deterioration, low cost of construction, and provisions for determination of the operating characteristics and thermal properties of the plasma.

Experimental results obtained in the laboratory agreed well with the design conditions. The rate of energy dissipated in the electric arc varied from 7. …

The Effect Of An Induction Field On Transducers., Ratilal S. Patel

Masters Theses

"This report presents the results of an experimental investigation on the effect of an induction field on transducer output. Various types of transducers; strain gages, thermocouples, and thermistors, were used. The changes in the output of these transducers were measured for various induction field conditions.

Measurements must often be made where strong electrical fields are present. Strain gages are used to measure the stresses in electrical machinery. Thermocouples and thermistors used for measuring the temperature of materials undergoing heat treatment with an induction heater are also subjected to an induction field.

The general experimental procedure was the same throughout the …

Solid-Phase Welding Of Nodular Iron To Low Carbon Steel., Scott H. Carriere

Masters Theses

“This paper presents an experimental investigation of the possibility of using solid-phase welding to join nodular iron to low carbon steel. Included is a review of available literature on solid-phase welding, tracing its origin from early Egypt to the present day. There was no previously reported work found on the welding of nodular iron to steel.

Experiments were performed to determine what temperature-pressure combination gave the greatest ultimate tensile strength These experiments resulted in the best welds being produced with an end load of 7000 pounds (35.700 psi) on a half inch diameter sample. The majority of these welds proved …

The Importance Of Radiation As A Means Of Controlling Surface And Internal Temperatures Of A Semi-Infinite Solid, Kenneth C. Woodruff Jr.

Masters Theses

"This problem is concerned with the temperature history of a semi-infinite solid bounded by one flat surface.

Heat was applied by convection from a hot fluid to the flat surface of the solid which was originally at a uniform temperature. Heat was radiated from the flat surface to black space and conducted into the solid according to Fourier's law. The temperature at the surface, and at several points beneath the surface, was determined as a function of time.

A method for solution of such a problem is demonstrated here by the use of numerical analysis and the Royal McBee LGP …

A Determination Of The Theoretical Stresses In A Deep Beam., James William Tritz

Masters Theses

"This paper presents an analytical solution of the stress distribution in a deep beam of finite length. The beam being considered is analyzed as one of plane stress. The method employed superimposes two stress functions each of which is a trigonometric series. The first stress function satisfies all boundary conditions except that of zero stress on the vertical faces. The second function is found, so that, when combined with the first function, all boundary conditions are satisfied. The IBM 1620 digital computer is then used to find the stresses for a particular beam. The results of this analysis are then …

Investigation Of The Effect Of The Wall Thickness On The Residual Stresses Developed In Thick Wall Cylinders Due To Water Quenching From The Outside Surface., Ghanshyam Chandubhai Patel

Masters Theses

"This investigation has been made to determine the residual stresses in thick wall cylinders by the use of strain gages.

The cylinders were quenched from their outer surface i n water from a temperature of 1000°F, and the resulting residual stresses were determined by Sachs boring-out method. The effect of the wall thickness of the cylinders on the residual stresses and the error developed due to the boring operation were discussed"--Abstract, p. ii

The Effect Of Surface Roughness, Cure Pressure, And Temperature Level On The Thermal Resistance Of Bonds And Contacts, David Leo Schwaller

Masters Theses

"This investigation was conducted to determine the thermal effect of temperature level, surface roughness, and curing pressure on bars and bonded interfaces.

The equipment used in this investigation is shown in Fig. 1 and Fig. 2. The four specimens used, cylindrical aluminum alloy bars, were cut radially at their midpoints and faced on a lathe. Heat was supplied by an electrical resistance heating element and an ice bath was used to conduct heat from the alloy specimen. A heat shield was used to insure one dimensional heat flow. Spacers were placed in the insulation at the top, the interface, and …

A Theoretical And Experimental Study Of The Stress Distribution In An Infinite Plane Shrink-Fitted On Four Circular Elastic Pins, Charles H. White

Masters Theses

"The purpose of this study is to show a general method of solution for multiple inclusions in an infinite plane. The shrink-fitting of an infinite plane upon the inclusions, or pins, will be simulated by force-fitting the pins into a large sheet of birefringent material, to obtain an experimental verification of the analytical solution.

The problem to be approached is that of four circular elastic pins shrink-fitted in an infinite plane. The method of superposition will be used, and the stresses at any point in the plane found with respect to a common origin of coordinates. It will first be …

The Effects Of Granular Size On The Thermal Conductivity Of Fine Sand, Fikri Yalvac

Masters Theses

"The Thomas method (1) for determining the thermal conductivity of solid materials can be used for the determination of the thermal conductivity of granular materials. In this thesis this method has been used to determine the effect of the granular size of sand cn its thermal conductivity.

River sand was classified according to size by the Tyler Standard Screen Scale into 50-60, 50-80, 80-100, 100-200, and below 200 mesh size. These sands were used for the experiments. The clay was separated from these samples to obtain pure river sand for the experiments.

According to the International Critical Tables, the thermal …

Test 870: Oliver 1850 Diesel, Nebraska Tractor Test Lab

Nebraska Tractor Tests

No abstract provided.

Test 872: Oliver 1950 Diesel 4wd, Nebraska Tractor Test Lab

Nebraska Tractor Tests

No abstract provided.

Test 875: Oliver 1850, Nebraska Tractor Test Lab

Nebraska Tractor Tests

No abstract provided.

Test 876: Oliver 1850 4wd, Nebraska Tractor Test Lab

Nebraska Tractor Tests

No abstract provided.

Test 863: Minneapolis-Moline U302 (Lpg), Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF TEST REPORT GENERAL CONDITIONS East tractor is a production model equipped for common usage. Power consuming accessories can be disconnected only when it is convenient for the operator to do so in practice. Additional weight can be added as ballast if the manufacturer regularly supplies it for sale. The static tire loads and the inflation pressures muse conform to recommendations in the Tire Standards published by the Society of Automotive Engineers. PREPARATION FOR PERFORMANCE RUNS The engine crank case is drained and refilled with a measured amount of new oil conforming to specifications in the operator’s manual. The …

Test 865: Case 750 (Diesel), Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF TEST REPORT GENERAL CONDITIONS East tractor is a production model equipped for common usage. Power consuming accessories can be disconnected only when it is convenient for the operator to do so in practice. Additional weight can be added as ballast if the manufacturer regularly supplies it for sale. The static tire loads and the inflation pressures muse conform to recommendations in the Tire Standards published by the Society of Automotive Engineers. PREPARATION FOR PERFORMANCE RUNS The engine crank case is drained and refilled with a measured amount of new oil conforming to specifications in the operator’s manual. The …

Test 866: Zetor 2011 (Diesel), Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF TEST REPORT GENERAL CONDITIONS East tractor is a production model equipped for common usage. Power consuming accessories can be disconnected only when it is convenient for the operator to do so in practice. Additional weight can be added as ballast if the manufacturer regularly supplies it for sale. The static tire loads and the inflation pressures muse conform to recommendations in the Tire Standards published by the Society of Automotive Engineers. PREPARATION FOR PERFORMANCE RUNS The engine crank case is drained and refilled with a measured amount of new oil conforming to specifications in the operator’s manual. The …

Test 867: Zetor 4011 (Diesel), Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF TEST REPORT GENERAL CONDITIONS East tractor is a production model equipped for common usage. Power consuming accessories can be disconnected only when it is convenient for the operator to do so in practice. Additional weight can be added as ballast if the manufacturer regularly supplies it for sale. The static tire loads and the inflation pressures muse conform to recommendations in the Tire Standards published by the Society of Automotive Engineers. PREPARATION FOR PERFORMANCE RUNS The engine crank case is drained and refilled with a measured amount of new oil conforming to specifications in the operator’s manual. The …

Generalized Programs For Heat Transfer Analysis., Ceylung Chu

Masters Theses

"This report presents numerical methods for calculating temperature distributions in any physical system in which heat transfer is taking place. The syste.11 may be at either a steadystate condition or a transient condition. The temperature distribution may itself be or primary interest, or it may be used further to calculate the flow or heat or thermal stress.

The system under investigation is divided into a certain number of subdivisions, or so-called "regions". A reference point (node point) will be taken as representative for the region which includes that point. The temperature at the "node point11 is taken to be the …

Theoretical Investigation Of Steam Jet Cleaning, Jaswant T. Lotwala

Masters Theses

"Steam cleaning methods are used by industries to remove mass of dirt and grease deposits from machine parts and other surfaces. It is necessary to know the rate at which this mass can be removed from a surface. The present investigation was made to determine this rate of mass removal. The mass transfer rate is influenced by two phenomena; namely, heat transfer and momentum transfer. Both of these were discussed and the results obtained from the analysis were used in determining the total mass transfer rate. The effects of various parameters, such as density and velocity of the cleaning fluid, …

Determination Of The Shapes Of Fixed And Moving Polodes Of Class Ii Four Bar Mechanisms., Manharkumar Kantilal Sheth

Masters Theses

"The purpose of this thesis is to determine the shapes of fixed and moving polodes of class II four bar mechanisms, since there has been little, or no work done in determining their shapes.

Twenty different mechanisms were taken to study the shape of the fixed and moving polodes. The best equation which fits each curve was found by using the least square method in polynomials. Coefficients for each curve were determined with the help of the I.BM 1620 computer. The equation was found to be a six-degree polynomial which fits very well to each curve. There seems to be …

The Effect Of A Lubricant On Tool-Workpiece Interface., Kenneth Eugene Spencer

Masters Theses

"The purpose of this study was to compare the effects of cutting fluids and the method of application to an orthogonal cutting process.

The cutting operation was performed on a lathe. The fluids use d were compressed air and a solution of emulsifiable oil and water.

The flooding of the area was produced by directing a copious supply of fluid over the cutting a rea. The directed stream was obtained by pumping the fluid through a small hole drilled into the tool holder, immediately above and behind the tool face, which directed the fluid at the tool-chip interface.

The results …

Use Of Sr-4 Strain Gages Under Hydraulic Pressure, Manubhai M. Patel

Masters Theses

"In this investigation an attempt has been made to determine the effects of hydraulic pressure on SR-4, type A-5 strain gages. A thick-walled aluminum alloy cylinder without end constraint was used to make an experimental study of the effects of hydraulic pressure on these strain gages.

The behavior of this cylinder under different internal hydraulic pressures was also studied by measuring the strains by means of strain gages which were attached to the inside and outside surface of the cylinder. The problem has been studied by applying pressures up to 4800 psi.

Because of the high internal fluid pressures various …

The Design, Construction, And Operation Of A Conducting Field Analog Computer., Richard T. Johnson

Masters Theses

"The purpose of this investigation is to design and construct a simple conducting field analog to solve problems described by the two-dimensional Poisson or Laplace equations. Decisions concerning choice of conducting media, construction of problem models, and design and construction of a specialized power supply with instrumentation were based on the results of previous experiments. Several problems are solved using the designed apparatus. Partial solutions to these problems are displayed in graphical form.

The greatest deviation of the experimental results from iterative values was consistently less than 8%. In most cases the deviation was less than 6%. The console arrangement …

Thermal Resistance Of Bonds And Contacts, David Marion Lewis

Masters Theses

"The adhesive and sealant Industry has more than kept pace with our rapidly expanding technology of today. This growth has left the standardization of data on adhesives far behind and lack of this data is obvious. Of the many applications, particularly as related to space technology and energy conversion, the resistance to the flow of heat offered by the bond layer is of considerable importance.

Little information is available on the effect of adhesives on heat transfer. In connection with their work on honeycomb panels, Rankle, Gier, and Bevans (7) determined the thermal resistance of the particular type of adhesives …

Influence Of The Heat Release On Thermodynamic Characteristics Of Diesel Engines., Shirish Amritlal Desai

Masters Theses

"A Diesel. engine is an internal. combustion engine in which the fuel. is ignited by the heat of compression. Thus, the Diesel. engines are known as compression-ignition (C.I.) engines. The engine received its name: from its inventor, Dr. Rudolf Diesel., who in 1893 published a book under the title, '' Theory and Construction 0£ Rational. Diesel Engine". The first successf'u1 Diesel. engines, using liquid: fuel., which was injected into the cylinder by a blast of high-pressure air, were manufactured by the M.A.N. Company of Germany in 1895"-- Introduction, p. 1

Experimental Evaluation Of Thermal Stresses On The Outer Surface Of A Thick-Walled Tube., Vinodray T. Patel

Masters Theses

"In this investigation an attempt has been made to measure thermal stresses on the outer surface of a thick- walled tube. The inside surface was heated by steam passing through the tube while the outer surface was cooled by water. Two temperature compensated strain gages were used to measure strains in the tangential and axial directions respectively. The advantage of using this type of strain gage is to avoid the use of a dummy gage to compensate for the temperature effect.

The analytical solution to the problem was derived and the values of thermal stresses were calculated theoretically and compared …

The Electrical Analogy Of Critical Speed For The Transverse Vibrations Of A Shaft With One, Two And Three Masses, Ashok Z. Patel

Masters Theses

"The object of this thesis is to determine the critical speed of a shaft by an electrical analogy. The shaft considered is of constant diameter and is simply supported at the ends by fixing it in self aligning bearings. The weight of the shaft is assumed to be proportionally distributed in the attached masses.

The original system is first of all converted to an equivalent simple spiring mass system by calculating the influence coefficients and hence frcan these determining the spring constants. The spring mass system obtained is then converted to an equivalent electrical circuit.

A sine-square wave frequency generator …

The Development Of A Temperature Probe And Temperature Survey Of The Interaction Of An Oblique Shock Wave And A Turbulant Boundary Layer, Donald M. Yano

Mechanical Engineering ETDs

The purpose of this investigation was to develop a miniature air temperature probe and to measure temperatures in the interaction region of an oblique shock wave and a turbulent boundary layer.