Digital Commons Network^™

Investigation Of Dirac‑Like Cones Induced Topologically Protected Wave Propagation (Tpwp) In Solid-Fluid Acoustic Metamaterials: A Combined Numerical And Experimental Study, Humza Khan

College of Graduate Studies: Theses & Dissertations

Topologically protected wave propagation (TPWP) is a unique phenomenon in acoustic metamaterial, where tailored geometries and material properties enable controlled energy absorption and localizations. This study investigates TPWP through the systematic variation of unit cell geometry to capture multiple Dirac-like cone interactions within the Brillouin zone. While prior research had emphasized solid-solid interactions, the present work extends the framework by incorporating a solid-fluid configuration.

The primary objective of this study is to determine the influence of unit cell volume and material selection on  the formation of Dirac-like cones in the Brillouin zone, as well as on the corresponding bandgap characteristics. …

Assessment Of Advanced Glazing Systems For Building Energy Efficiency In Hot-Arid Climates, Ahmad I. Elshamy, Yousef Elgefly, Yara El-Metwally, Serag Salem

Architectural Engineering

The built environment is considered among the most contributing factors to energy consumption. The building envelope plays a crucial role in determining the building energy consumption, regulating heat transfer and maintaining adequate indoor environmental quality. Hence, optimizing the thermal performance of the building envelope by achieving optimal glazing solutions while fulfilling the Sustainable Development Goal (SDG 7) is the main aim of this research. This study investigates the impact of various facade glazing systems on the building energy performance, focusing on the cooling energy consumption of an office building in a hot arid climate, Cairo, Egypt. The novelty of this …

Overcoming Resolution Vs. Throughput Trade-Offs In Ceramic Material Extrusion Additive Manufacturing Via Viscoelastic Filament Stretching, Abid H. Rafi, David W. Lipke, Jeremy L. Watts, Gregory E. Hilmas, Ming C. Leu

Materials Science and Engineering Faculty Research & Creative Works

Fabricating large, monolithic ceramic parts using material-extrusion additive manufacturing remains challenging due to difficulty maintaining uniform moisture content during printing, which can lead to drying-induced defects such as warping and cracking, especially as part size and print time increase. Fabricated parts have trade-offs among print resolution, high throughput, and structural fidelity. Our study has shown that increasing the ratio of nozzle traverse speed vs. material extrusion speed increases filament stretching in viscoelastic ceramic paste, helping to overcome the trade-offs between resolution and throughput. Using aqueous ZrB2–SiC (70/30 vol.%) as a representative ultra-high temperature ceramic paste, rheological characterisation revealed viscoelastic yield-stress …

Simulated Lunar Gravity Testing Of A Magnetic And Electrostatic System For Beneficiating Lunar Regolith, Blake A. Coffman, Gabriel Porter, Lindsay Manteufel, Mitchell Cottrell, Jeffrey D. Smith, David J. Bayless, William Shonberg, Frank D. Han, Fateme Rezaei, Kirby Runyon

Materials Science and Engineering Faculty Research & Creative Works

We present the design and testing of a lunar regolith beneficiation device that utilizes magnetic and electrostatic separation methods to concentrate desired minerals by removing unwanted material, such as the mineral anorthite, from bulk lunar regolith. The beneficiated materials would have value for downstream in-situ resource utilization (ISRU) processes such as metal extraction, oxygen extraction, and metal oxide additive manufacturing processes. The apparatus uses a dual-strength magnet system with N52 and N42 neodymium magnets to separate particles by magnetic susceptibility. The electrostatic separation system, which acts like a sieve, sorts the regolith simulant by particle size using a single-phase 50% …

The Effect Of Chamber Geometry On The Performance Of Oscillating Water Column, Timilehin O. Osunade

College of Graduate Studies: Theses & Dissertations

This thesis investigates the effect of internal chamber geometry on the performance of a piezoelectric oscillating water column (OWC) wave energy harvester. Four acrylic chamber configurations with internal top-surface angles of 0°, 30°, 45°, and 60° were tested under 32 controlled conditions combining synchronous (SYN) and asynchronous (ASC) forcing at input voltages of 4, 6, 8, and 10 V. A 35 mm piezoelectric disc mounted at the chamber roof served as the power take-off element and, subject to the RC-limit caveat disclosed in Section 3.2.1, as a first-order dynamic analogue of the chamber pressure for phase-based compressibility analysis. All test …

Effect Of Graphene Oxide On The Upconversion Photoluminescence Behavior Of Er/Yb Co-Doped Pvdf-Go Composite Nanofibers, Saptasree Bose, Jack Ryan Summers, Bhupendra B. Srivastava, Karen Lozano, Victoria Padilla-Gainza

Mechanical Engineering Faculty Publications

Upconversion photoluminescence (UCPL) materials, particularly rare-earth (RE) doped nanoparticles, have garnered significant attention due to their ability to convert near-infrared (NIR) excitation into visible emission, offering benefits such as high photostability, long lifetimes, low autofluorescence, and deep tissue penetration. Among various platforms, polymer-based one-dimensional (1D) nanofibers with in-situ lanthanide doping remain relatively unexplored, despite their superior mechanical flexibility, processability, and potential for improved luminescence performance. In this study, we report the fabrication and UCPL quenching behavior of Er3+/Yb3+ co-doped polyvinylidene difluoride (PVDF) nanofibers incorporated with graphene oxide (GO), synthesized for the first time using the scalable Forcespinning® technique. PVDF, a …

Teleoperated Robotic Arm With Vision-Based Imitation Learning, Favour E. Emmanuel, Hunter J. Donahue

Williams Honors College, Honors Research Projects

This report presents the design, development, and deployment of a teleoperated robotic arm system capable of vision-based imitation learning. The system uses a leader-follower architecture with myArm C650 and myArm M750 robots manufactured by Elephant Robotics. The leader arm movement is controlled by the operator, whereas the follower performs actions acquired from demonstrations. Data collection included synchronized joint-angle recording and multi- camera video streams capturing human demonstrations.

These demonstrations were processed with a deep learning imitation algorithm called Action Chunking with Transformers (ACT). The main capability of this algorithm is its ability to make future action predictions based solely on …

Areosense, Josephine Turney

Williams Honors College, Honors Research Projects

The AeroSense growing system is designed to make indoor aeroponic gardening easy and accessible for everyone. By combining sensors, automation, and AI, the system can monitor and adjust humidity, lighting, and nutrient levels to help plants thrive without requiring expert knowledge. The goal is to create a self-regulating garden that takes the guesswork out of growing fresh herbs and vegetables at home. The project involves building a working aeroponic prototype equipped with misters, pumps, and environmental sensors, all managed by a Raspberry Pi. Using computer vision and machine learning, AeroSense will be able to assess plant health and respond automatically …

Using A Record Player Inspired Probe System To Investigate Adhesion And Friction Of Tire Rubber At Micrometer Length Scales, Kyle J. Galigher, Brendan Schmitt

Williams Honors College, Honors Research Projects

We will be using the principles behind how a record player turns physical grooves into electrical signals to develop a device that can be used to measure the surface of tires. The device will be capable of measuring the surface roughness of rubber samples from both new and worn tires, in order to compare the differences between them. It will be operable at varying speeds, and will produce electrical signals that correspond to the bumps along the surface of the rubber. The design will be carried out and optimized with the use of SolidWorks modeling, finite element analysis, motion analysis, …

High-Speed Non-Pneumatic Tire (Npt) Design For Speeds Above 60 Mph, Jacob Grams, Brady Maurer, Jake Groewa

Williams Honors College, Honors Research Projects

This project focuses on developing a high-speed non-pneumatic tire (NPT) capable of safely operating at speeds greater than 60 mph, a performance range where most existing airless tire designs fail due to structural instability and performance limitations. The objective of this work is to design, analyze, and prototype a structurally optimized honeycomb-based tire structure with improved load distribution, deformation control, and durability. Multiple geometries were evaluated using finite element analysis (FEA) to assess stress and maximum resultant (total) displacement behavior under loading conditions, and a material selection study was performed to identify a suitable material for the design. The final …

Eletric Charging Arm Mechanism - E-Charm, Jacob A. Lewis, Gabriel A. Greer

Williams Honors College, Honors Research Projects

As demand for electric and hybrid vehicles continues to rise, many EV owners rely on home charging in their garages. Gabriel Greer and I’s Senior Design Project, the Electric Charging Arm Mechanism (ECHARM), addresses this by creating a robotic system that autonomously detects a vehicle’s charging port, connects to it, and returns to a rest position when charging is complete. ECHARM is designed as a six-axis robotic arm with wrist and shoulder joints driven by stepper motors through custom cycloidal drive gearboxes. A closed-loop control system using rotary potentiometers ensures precise motion control. At the end of the arm is …

Analysis Of Policies And Incentives For The Successful Implementation Of Hydrogen-Fueled Medium-Duty And Heavy-Duty Vehicles In Humboldt County, California, Alka Verma

Cal Poly Humboldt theses and projects

The 21st century has seen a significant rise in global greenhouse gas (GHG) emissions, with the transportation sector contributing 23% of these emissions. Medium-duty and heavy-duty vehicles (MD/HD) are particularly impactful, accounting for over a quarter of transport-related emissions. In Humboldt County, California, transportation represents 53% of total emissions, with MD/HD vehicles being a major contributor. As light-duty vehicles shift to zero-emission alternatives, the MD/HD sector faces unique challenges. Hydrogen fuel cell vehicles offer a promising solution, providing longer range, higher energy density, and quicker refueling compared to battery electric vehicles (BEVs). These features make hydrogen an attractive option for …

Tomo-Piv Study Of Baseline Flow Structures Behind A Strut Injector, Josiah Mcdermott, Connor Bell, Davide Viganò

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Stabilizing combustion in scramjet engines is a formidable challenge due to the small-time scales afforded for air-fuel mixing. Numerous studies in this area have demonstrated the potential of strut-style platforms for fuel injection and mixing enhancement, which remains an active area of research. In the Aerodynamics Research Laboratory at Missouri S&T, a strut-style injector system has recently been installed. In this study, we characterize the baseline flow structures behind this platform absent fuel injection. The wake generated by a strut itself has an appreciable impact on the resulting air-fuel mixing, which motivates its characterization. In future studies, this characterization will …

Computational Fluid Dynamics Simulation Of In-Situ Plasma- Assisted Cold Spray, Lucas Degen

Electronic Theses and Dissertations

Cold spray is a solid-state form of additive manufacturing with high versatility and widespread applicability, especially in relation to metal coatings. Many applications exist within the fields of aerospace, defense and energy systems to obtain sustainable, temperature and corrosion resistant, robust coatings. High-strength alloys and refractory metals generally encounter challenges with regards to cold spray coating adhesion and overall deposition efficiency. Heat induced methods of post-processing or in-situ treatment have been explored to encourage particle softening in the cold spray plume, as well as coating recrystallization to enhance material properties. These approaches have primarily been limited to an experimental approach, …

Effects Of Hydrogen Enrichment And Premixing On Flame Stability In A High-Pressure Axial-Stage Combustor, Alexandre Fernandes C. Santiago Filho

Honors Undergraduate Theses

The addition of hydrogen to conventional fuels enhances reactivity and can increase the risk of flashback in premixed gas turbine combustors. This study investigates the effects of premixing length and hydrogen concentration on flame stability in a high-pressure axial-stage combustor. Experiments were conducted at the UCF Propulsion and Energy Research Laboratory using a two-stage configuration, where the primary stage provided a high-temperature vitiated crossflow using a hydrogen-piloted, premixed methane–air mixture, and hydrogen-enriched methane–air mixtures were injected through a concentric fuel-tube injector in the axial stage. Premixing length was varied for pure hydrogen flames, and hydrogen concentration was varied at a …

Evaluation Of The Long-Term Sealability Performance Of Aramid Fiber Nitrile-Based Gaskets, Salome Ramirez

Honors Undergraduate Theses

The reliability of sealed, oil-filled containers is critical for maintaining the operation of high-voltage energy systems, in which the sensitive electronics need to be isolated from the cyclic conditions associated with outdoor environments. New materials bring the possibility of extending service lifetimes and maintenance intervals. Aramid fiber nitrile-based gaskets are an attractive alternative to conventional gasket choices due to their long-term stability in various environments and compatibility with porcelain, metals, and plastics. For newly designed porcelain-to-metal fittings, understanding the behavior of the candidate gasket material under realistic loading conditions is essential to ensure long-term seal integrity and equipment safety. Traditional …

Increasing Actuation Authority And Bandwidth For Aeromechanics Testing: A Piezoelectric-Based Approach, Sydney A. Giannuzzi

Graduate Studies Theses and Dissertations 2026

Flutter in turbomachinery poses significant risks to aerospace systems, requiring accurate identification of flutter boundaries to ensure operational safety. Traditional binary “flutter / no flutter” testing methods provide limited data without error margins. Aeromechanical Identification Methodology (AIM) offers a safer alternative by mapping aeromechanical damping across operational conditions using non-contact excitation. However, current AIM actuators are constrained to excitation frequencies below 500 Hz, limiting their effectiveness and applicability. To bridge this gap, this research analyzed and validated performance of a novel piezoelectric-based oscillatory flow injection valve (NOVA) designed to deliver high-bandwidth, high-authority actuation for expanded flutter boundary mapping.

NOVA was …

Multi-Objective Optimization Strategy For Component Sizing In Solar-Hydrogen Microgrids Using An Advanced Hybrid Genetic Algorithm, Dylan Jones

UNF Graduate Theses and Dissertations

This thesis presents the development of a genetic algorithm (GA) optimization framework for the design and component sizing of hybrid solar-hydrogen microgrids. The framework addresses a critical gap in research and existing commercial tools by unifying performance maximization and cost minimization objectives across both grid-tied and islanded configurations. Integrating solar photovoltaics, electrolyzers, hydrogen storage, fuel cells, and batteries, the GA employs adaptive weighting and dynamic boundary constraints to balance technical feasibility with economic efficiency. To ensure real-world viability, the algorithm relies on a novel Daylight Sun Factor (DSF) for localized solar assessment and was rigorously validated against multi-year, high-fidelity irradiance …

Mechanical Behavior Of Additively Manufactured Ti-6al-4v Eli Parts: Effects Of Laser Parameter Selection, Samuel Lopez

UNF Graduate Theses and Dissertations

Additive manufacturing (AM) of TI-6AL‑4V Extra‑Low Interstitial (ELI) enables complex geometries for fatigue‑critical medical device applications, yet fatigue performance remains sensitive to process‑induced defects. This work investigates the effect of laser process parameter selection on the microstructure, mechanical properties, and fatigue behavior of TI- 6AL‑4V ELI fabricated via laser powder bed fusion (L‑PBF) using a Renishaw RenAM system. The influence of laser parameters was isolated by holding powder chemistry, build orientation, scan strategy, sub‑transus annealing, and post‑processing constant between a non‑optimized baseline and an optimized parameter set selected based on tensile performance.

Optical microscopy showed the optimized condition exhibited improved …

The Effects Of Weathering On The Very High Cycle Fatigue Behavior Of Aluminum 6061-T6, Rama Albatesh

UNF Graduate Theses and Dissertations

Aluminum 6061-T6 is commonly used in structural and transportation applications due to its strength-to-weight ratio, corrosion resistance, and ease of manufacturing. In many practical situations, components made from this alloy experience cyclic loading while exposed to environmental conditions such as humidity, temperature changes, and ultraviolet radiation. These factors can affect surface integrity and fatigue performance, especially in the very high-cycle fatigue (VHCF) regime.

This study aims to explore how accelerated weathering impacts the ultrasonic fatigue behavior of Aluminum 6061-T6. First, assess the material through tensile testing to determine its mechanical properties. Then conducted microstructural analysis using optical microscopy, scanning electron …

Development And Testing Of A Low-Cost Inertial Impact Sensor, Gabriel Michael Pesek

UNF Graduate Theses and Dissertations

Acceleration sensors have seen increasing usage within sports to detect when somebody receives an impact to their head which can potentially lead to Traumatic Brain Injury (TBI). While adoption of these sensors has steadily risen, the cost of these sensors is often cited as a reason they have not been as widely adopted, especially for amateur teams. This leads to the need for a lower-cost option for detecting these impacts. To fill this gap, a low-cost, lightweight acceleration sensor was designed that exploits the inertia of a working fluid on impact in order to rupture a metallic membrane which acts …

Thermomechanical Modeling Of Transpiration Surfaces For Hypersonic Propulsion, Spencer D. Smith

Graduate Studies Theses and Dissertations 2026

Hypersonic flight vehicles are a promising form of high speed passenger transport and efficient space access architectures. However, they are fundamentally a thermally limited technology. High heat fluxes exceeding 10 MW/m2 and gas temperatures between 3000-4000K can be found both within the engine, and on the outer surface. Current conventional engineering materials are non-viable at these conditions. In order to make these materials viable, active cooling strategies could be utilized. One particularly promising type is transpiration cooling, where a coolant is diffused through a porous surface. Although researched heavily in the 1960s, adoption is still minimal. Part of the reason …

Experimental Characterization Of Obstacle-Driven Ddt And The Performance Of Relief Dump Tanks In Detonation Systems, Bryan Suarez

Graduate Studies Theses and Dissertations 2026

This study investigates the lifecycle of a detonation event in a modular detonation
tube facility. It focuses on the mechanisms of deflagration-to-detonation transition
(DDT) and the effectiveness of a pressure relief system. With a stoichiometric
hydrogen-oxygen mixture, the research aims to characterize the effect of
interchangeable turbulator obstacles on the DDT process. By varying blockage
ratios and obstacle geometries in the pre-detonation section. This study identifies
how physical characteristics influence transition efficiency. The experimental data
collected includes pressure spikes and wave speed which were then used to
validate against the Chapman-Jouguet (CJ) theory at initial pressures of 350 Torr
and …

Machine Learning Modeling Of In-Situ Effective Thermal Conductivities And Ablation Behaviors Of Ceramic Matrix Composites Under Hydrogen Combustion Environments For Gas Turbine Engines, Jayanta Bhusan Deb

Graduate Studies Theses and Dissertations 2026

Through the integration of experimental characterization, machine learning, deep learning, numerical modeling, and physics-informed artificial intelligence, this dissertation explores the thermal performance of polymer-derived ceramic matrix composites (CMCs) for hydrogen combustion environments. The polymer infiltration and pyrolysis (PIP) process was used to create Yttria-stabilized zirconia (YSZ)-fiber-reinforced ceramic matrix composites, which were then experimentally assessed under hydrogen torch and hydrogen combustion conditions typical of next-generation gas turbine and aerospace propulsion systems. Front- and back-surface temperature measurements were used to continually monitor thermal reactions, and post-test microstructural characterization and numerical simulations were carried out to evaluate material integrity and heat-transfer behavior. To …

Performance Analysis Of Labyrinth And Hybrid Seals For Supercritical Co₂ Turbomachinery Applications, Ghanshyam Sarobar Mandal

Graduate Studies Theses and Dissertations 2026

Leaks account for large losses in turbomachinery systems, which has led to research on sealing technologies. The work presented studies the effect of a hybrid seal combining conventional labyrinth geometry and honeycomb structure by simulating supercritical carbon dioxide (sCO₂) flow through this geometry. The CFD solver compares effects such as changes in mass flow rate, formation of vortices, pressure profile, and seal performance as geometry angles of labyrinth teeth and honeycomb walls change at conditions normally found at higher pressures in these seals. Honeycomb walls were placed on the stator, ranging from 125°< θc< 55°. Labyrinth teeth were placed on the rotor at the same degrees. Honeycomb cell diameters were also varied, creating more resistance and turbulence within the flow. It was discovered that the honeycomb angle created stronger effects on vortices and boundary layer formation, while the labyrinth angle mainly affected the throttling of flow and loss generation. Combining all three angles created a relationship dictating the seal leakage. Dimensions of seals were based on gas turbine seals with changes to meet sCO₂ conditions. ANSYS was used to simulate static and rotating conditions until convergence on a specific geometry

Two-Phase Transcritical Carbon Dioxide Flow At The Microscale For Thermal Management Applications, Soroush Niazi

Graduate Studies Theses and Dissertations 2026

High-power electronic and power-conversion devices now generate heat fluxes that exceed what conventional air- and single-phase-liquid cooling can dissipate, motivating the search for more capable coolants and cooling mechanisms. Carbon dioxide is an attractive candidate for this role: it is inexpensive, non-toxic, and environmentally friendly, and near its critical point its thermophysical properties change rapidly, which raises the heat-transfer coefficient. In addition, a large pressure drop produces strong cooling through the Joule–Thomson effect and phase change, so that the throttling element itself becomes a source of cooling. This dissertation studies the throttling, phase change, and choking of high-pressure carbon dioxide …

On Performance And Applications Of A Liquid Fueled Pulsed Flame Jet Igniter, Gerardo A. Rodriguez

Graduate Studies Theses and Dissertations 2026

As global demands for supersonic and hypersonic flight heighten, high-speed air breathing propulsion technologies stand out as a worthwhile direction to overcome many of the limitations that turbomachinery-based engines face at supersonic speeds. Air breathing propulsion concepts are attractive for their geometrical simplicity, using supersonic incoming air to provide compression. Scramjet flight vehicles operate within the hypersonic flight regime and have been a global research topic, especially in the 21st century, for defense and combined cycle engine architectures. As scramjet technology continues maturing towards widespread use, efforts have converged on liquid hydrocarbon fuels for storage, range, and operational benefits. Flight …

Study On Fracture Toughness Under Different Modes Through Continuum Damage Mechanics Based Fracture Locus, Yeting Sun

Graduate Studies Theses and Dissertations 2026

Traditional elastic-plastic fracture mechanics (EPFM) relies on crack-tip analysis, whereas continuum damage mechanics (CDM) is typically calibrated from uncracked bodies. This dissertation aims to bridge the gap between these two fundamental branches by explicitly linking fracture toughness with ductile damage models. Based on the assumptions regarding Mode I crack deformation, analytical solutions are derived to establish a novel relationship among Mode I fracture toughness, CDM-based ductile fracture strain, and material strain hardening capability. This theoretical framework is subsequently extended to encompass Mode II and Mode III loading conditions. To validate the proposed relationships, finite element (FE) models are developed in …

Advanced Ysz/Si(B)Cn And Bnnt/Si(B)Cn Ceramics Matrix Composites For Extreme Environments In Hydrogen Combustion, Yiting Wang

Graduate Studies Theses and Dissertations 2026

The growing demand for carbon-neutral energy conversion has accelerated the development of hydrogen-fueled gas turbine systems, which operate at significantly higher temperatures and more chemically aggressive environments than conventional natural gas turbines. To meet these stringent requirements, ceramic matrix composite (CMC) materials consisting of yttria-stabilized zirconia (YSZ) fiber reinforced Si(B)CN ceramic matrix were developed. To further enhance in-plane heat dissipation, thermal stability, thermal shock resistance, and thermal cycling performance, a Si(B)CN/Boron Nitride Nanotubes (BNNT) nanocomposite coating was incorporated onto the YSZ/Si(B)CN composites. Microstructural characterization confirmed the formation of a continuous Si(B)CN ceramic matrix reinforced with uniformly distributed BNNTs. The resulting …

Turbine Exhaust Cylinder And Manifold Wake Interactions At High Swirl Angle, Christian A. Anzalotta

Graduate Studies Theses and Dissertations 2026

A commonly observed flow interaction in industrial gas turbine (IGT) exhaust diffuser configurations is investigated, where upstream structural wakes interact with downstream airfoil-like components, potentially leading to unsteady loading. To better understand the mechanisms contributing to this behavior, a scale-model is designed. Dynamic similarity is achieved by matching the Strouhal number (St) of the vortex shedding from the strut. A bell-mouth followed by a swirler is installed in front of the strut to mimic the flow angles at the inlet section of the turbine exhaust. Experiments are conducted for three swirl angles, namely, 30°, 45°, and 60°. Power spectra computed …