Digital Commons Network^™

Numerical Analysis Of Impact Vibration Based On A Bifurcation Diagram With Two Varying Control Parameters, June-Yule Lee

Journal of Marine Science and Technology–Taiwan

This study investigates impact vibration by using a bifurcation diagram with one or two varying control parameters. Sticking, periodic, and chaotic motions are explored using the Poincaré mapping and impact mapping techniques. A full range of bifurcation diagrams with varying driving frequencies is obtained, and the statistical index of the standard deviation (Std) is used to calculate the impact series in the bifurcation diagrams. The results indicate strong agreement between impact conditions and their corresponding statistical index values for the Std. Subsequently, the Std values for two control parameters of (w, m), (w, c), (w, k), (w, f), and (w, …

Carbon Capture, Utilization, And Storage, University Of North Dakota. Energy And Environmental Research Center

EERC Brochures and Fact Sheets

Fact sheet about carbon capture, utilization, and storage (CCUS) and the Energy & Environmental Research Center’s CCUS capabilities. Includes information on the Plains CO₂ Reduction (PCOR) Partnership initiative, Brine Extraction and Storage Test (BEST), Carbon Storage Assurance Facility Enterprise (CarbonSAFE), Red Trail Energy Carbon Capture and Storage, a feed study at Coal Creek Station, Bell Creek and Cedar Creek anticline projects, and Partnership for CO₂ Capture (PCO₂C).

Micro-Scale Laser-Induced Fluorescence Thermometry For Multiphase Flow In Porous Media, Samuel J. Simmons

Master's Theses

In this thesis the use of Laser-Induced Fluorescence (LIF) thermometry was evaluated as a temperature measurement for multiphase flow in porous media. This optical temperature measurement technique utilizes the temperature-dependent emissive properties of fluorescent dyes to measure temperature. This research evaluates the accuracy, spatial resolution, and temporal resolution of LIF thermometry compared to existing temperature measurements. In this research water-soluble and oil-soluble fluorescent dyes are evaluated in terms of their temperature sensitivity. The ability of these dyes to measure temperature is compared to an Ansys FEA simulation of a fixed temperature gradient. For multiphase flow, the fluorescent dyes were both …

Programming The Bistable Dynamic Vibration Absorbers Of A 1d-Metastructure For Adaptive Broadband Vibration Absorption, Shantanu H. Chavan

Dissertations, Master's Theses and Master's Reports

This research addresses a critical challenge in structural engineering—achieving comprehensive vibration control and energy dissipation in meta-structures. Departing from the limitations of passive structures with fixed bandgaps, we propose an innovative approach utilizing active meta-structures capable of dynamically tuning their bandgaps. The primary goal is to introduce an efficient method for programming meta-structures with multiple variable bandgaps, thereby enabling effective vibration attenuation across a broad frequency spectrum.

The methodology involves transforming passive resonators into bistable adaptable Dynamic Vibration Regulators (DVRs) through a sophisticated switching mechanism. This adaptation sets the stage for numerous unique combinations by independently switching each resonator. A …

Multi-Chamber Silencer Composed Of Screw-Perforated Tubes And Straight-Perforated Tubes, Tian-Syung Lan, Min-Chie Chiu

Journal of Marine Science and Technology–Taiwan

The use of silencers to reduce noise is mandatory due to severe hearing damage caused by high venting noise in the engine room of ocean-going vessels. While straight and perforated tubes have been used as acoustical elements in traditional silencer design, studies have shown that the acoustical design still requires improvement. To enhance acoustical efficiency, the use of multi-chamber mufflers is proposed composed of screw and perforated tubes. Additionally, a mathematical finite element model built for acoustical simulation using the COMSOL program expedites the analysis of silencers with complicated acoustical elements. A sensitivity analysis of transmission loss concerning the geometric …

Rapid Species Identification Of Meretrix Lusoria And Three Other Meretrix Clams Using Pcr And Rflp Analysis Of The Mitochondrial Coii Gene., Chia-Hsuan Sung, Liang-Jong Wang, Chang-Wen Huang

Journal of Marine Science and Technology–Taiwan

Meretrix clams are among the most economically important species of bivalves in Eastern Asia and Taiwan. In the past, the identification of these hard clams depended on the shell morphology; however, species identification based on shell markings and shapes confuses the taxonomy of the Meretrix genus. The DNA molecular information is useful and can easily identify them accurately and quickly, especially the sequence of mitochondrial DNA. In this study, a PCR method to analyze the mitochondrial cytochrome c oxidase II (COII) gene was developed to rapidly identify of M. lusoria, M. lamarckii, M. lyrata and M. petechialis. Four different species …

Bearing Capacity Factor Characteristics Of Footings On Double-Layered Cohesive Soils, Chao-Ming Chi, Zheng-Shan Lin, Yu-Shu Kuo

Journal of Marine Science and Technology–Taiwan

In this study, the bearing capacity of a surface foundation resting on a double-layered cohesive soil profile was investigated by applying a rotational mechanism and finite-difference numerical simulations. The bearing capacity factor behaviors of a surface footing on double-layered cohesive soils can be classified and illustrated using a characteristic chart. Depending on the soil strata strength ratio and normalized layer thickness, the soil-foundation system can be in the squeezing, factor-increasing, factor-decreasing, or constant factor zones. The results indicated that the trend of the curves in the characteristic chart computed from the asymmetric failure mechanism was in accordance with that of …

Research On Ice Resistance Of Ships Sailing In Floating Ice Floe, Zhixin Xiong, Xinyuan Wu, Yang Li

Journal of Marine Science and Technology–Taiwan

To study the ice resistance of ships in areas with floating ice, the Xuelong 2 icebreaker was simulated. A floating-ice model was established using the discrete-element method, and an ice particle array was generated using MATLAB. The effects of ice coverage and speed on ice drag were studied From the numerical simulation results, it can be seen that there is a certain trend in ice resistance under different ice coverage ranges, which changes with the change of speed.By comparing with the empirical formula and the numerical value of the ship model test, this numerical simulation results are relatively accurate.It also …

The Pre-Processing Of Wt Blade Images By Ss And Bilateral Filter With Machine Learning Frameworks, Joy Iong-Zong Chen, Chien-Yeh Lee, Wien-Chieh Lo

Journal of Marine Science and Technology–Taiwan

This paper discusses the motivation behind turbine migration and addresses the challenges of using NN (neural network) computing systems. Moreover, it focuses on high-dimensional data from WT (wind turbine) blades. The three key aspects addressed in this study are turbine migration, overfitting, and strict feature selection. To evaluate the performance of the machine learning system, the study considers the characteristics of WT blades, specifically the similarity in blade color and the differences in shape. The authors apply pre-processing techniques, in particular a bilateral filter, in conjunction with the SS (selective synthesizer) of blade fouling patterns. The SS method adopts the …

A Comparative Analysis Of Coastdown Testing Methods From An Electric Drive Unit Engagement Perspective Using A Student-Designed Parallel Hybrid Electric Vehicle, Dawson Everett Dunnuck

Graduate Theses, Dissertations, and Problem Reports (ETD)

Coastdown testing and road load determination are pivotal parts of the automotive design process. Vehicle manufacturers and independent companies perform and analyze road loads determined through a coastdown or similar method to determine a vehicle’s road load for modeling and EPA certification. For a traditional coastdown, the vehicle’s drivetrain must be disconnected through a clutch between the engine and the transmission while traveling at a high rate of speed to place the vehicle in neutral. This changes for hybrid and electric vehicles. Some hybrid, and most electric, vehicles delivered to customers do not have this clutch action to grant the …

Accelerating Manufacturing Decisions Using Bayesian Optimization: An Optimization And Prediction Perspective, Taofeeq Olajire

Graduate Theses, Dissertations, and Problem Reports (ETD)

Manufacturing is a promising technique for producing complex and custom-made parts with a high degree of precision. It can also provide us with desired materials and products with specified properties. To achieve that, it is crucial to find out the optimum point of process parameters that have a significant impact on the properties and quality of the final product. Unfortunately, optimizing these parameters can be challenging due to the complex and nonlinear nature of the underlying process, which becomes more complicated when there are conflicting objectives, sometimes with multiple goals. Furthermore, experiments are usually costly, time-consuming, and require expensive materials, …

Finite Element Modeling And Analysis Of Breech Face Impressions, James A. Hamilton

Graduate Theses, Dissertations, and Problem Reports (ETD)

Finite element analysis (FEA) is a technique which has not been widely used in Forensic Science in general and firearms examination in particular. The general utility of FEA was assessed by the simulation of scenarios commonly encountered during the investigation of firearm related crimes. As a test, simulations included the perforation of a windshield and sheet metal with a 9 mm projectile, the development of pseudo subclass characteristics during the manufacturing of a breech face, and the impact of a projectile with another projectile in air and with a solid body. Results from the simulations were compared to projectiles and …

Imitation Learning For Swarm Control Using Variational Inference, Hafeez Olafisayo Jimoh

Graduate Theses, Dissertations, and Problem Reports (ETD)

Swarms are groups of robots that can coordinate, cooperate, and communicate to achieve tasks that may be impossible for a single robot. These systems exhibit complex dynamical behavior, similar to those observed in physics, neuroscience, finance, biology, social and communication networks, etc. For instance, in Biology, schools of fish, swarm of bacteria, colony of termites exhibit flocking behavior to achieve simple and complex tasks. Modeling the dynamics of flocking in animals is challenging as we usually do not have full knowledge of the dynamics of the system and how individual agent interact. The environment of swarms is also very noisy …

Multimaterial, Core-Shell Direct Ink Writing Of Flexible Strain Sensors For Pneumatically-Actuated Soft Robotic Hinge Joints, John Michael Burke

Graduate Theses, Dissertations, and Problem Reports (ETD)

Direct ink writing (DIW) provides for an expansive material library and the ability to print multiple materials with tailored functionalities in a controllable and single-step process. Particularly beneficial is the net shape printing under ambient conditions of a wide range of materials normally incompatible with one another. Coaxial DIW is a 3D printing technique that allows for two dissimilar inks to be extruded simultaneously in a co-flow manner. In this work, custom-designed coaxial nozzles were 3D-printed using a stereolithography printer. Composite inks comprised of thermoplastic polyurethane and silver were developed and studied. The coaxial nozzles were then used to co-extrude …

Lithium-Ion Battery Safety Analysis With Physical Sub-Models, Samuel Abimbola Ogunfuye

Graduate Theses, Dissertations, and Problem Reports (ETD)

Ever-increasing explosions occurring globally at a rapid rate and in diverse situations have re-established the fact that novel, faster, and more accurate approaches must be developed to analyze and possibly curb these explosions and avert their future occurrences. Experimental endeavors and computational fluid dynamics (CFD) simulations as compared to engineering models generally require enormous time, and resources, as well as a high-level of expertise and technicalities. This might, however, delay prompt analysis and the ability to draw conclusions, thereby causing setbacks in recommending safety measures for different situations and conditions. Therefore, robust models which are accurate and fast to give …

Structural Health Monitoring Using Machine Learning And Synthetic Data, Michail Tzimas

Graduate Theses, Dissertations, and Problem Reports (ETD)

Structural health monitoring spans many decades of research across multiple engineering fields. However, typical monitoring processes for damage detection of complex structures usually prohibit real-time or fast detection of debilitating damage to the structure. One of the major issues of real-time detection of damage is the enormity of data that needs to be processed, which is worsened by the relative inability of fast relaying of data to structural engineers. With the rapid advancement of Machine Learning, both issues can be overcome, and detection of failure is achieved with non-invasive techniques. This dissertation explores the applicability of Machine Learning as a …

Evaluating Electrification Of Fossil Fuel-Fired Boilers For Decarbonization Using Discrete Event Simulation, Nahian Ismail Chowdhury

Graduate Theses, Dissertations, and Problem Reports (ETD)

Decarbonizing fossil fuel usage is crucial in mitigating the impacts of climate change. CO2, which comprises the major portion of greenhouse gas, is emitted from burning fossil fuels. One of the significant sources of fossil fuel user is industrial process heating, and most of the heating in industrial processes is achieved through boilers. Electrification is a promising solution for decarbonizing these boilers, as it enables renewable energy sources to generate electricity, which can then be used to power the electric boilers. The electrification of boilers can reduce greenhouse gas emissions, improve air quality, and increase energy efficiency. However, it requires …

Studies On Non-Transition Metal Substitution To Ab2 Metal Hydride Alloys For Battery Application, Shiuan Chang

Wayne State University Dissertations

Nowadays, multiphase transition metal-based AB2 metal hydride alloys and the rare-earth metal-based AB5 alloys (currently used in consumer NiMH batteries) are used as negative electrodes in NiMH batteries. It is of great interest to explore the possibility of significantly improving NiMH battery performance to compete with Li-ion batteries. In this area, the effect of dopant elements from Group-IA, -IIA, -IIIA non-transition metal family has not been thoroughly studied. In this study, lithium, magnesium, and boron (a metalloid considered metal in this study) were chosen as modifiers in the C14-phase predominant AB2 alloy by different dopant concentrations and synthesis methods, doping …

Study Of Bounds For Effective Moduli Of Polycrystals And Composites Using Variational Principle For Probabilistic Measures, Md. Tofiqul Islam

Wayne State University Dissertations

Tensors that are invariant with respect to subgroups of 3D group of rotations were constructed first by Lokhin and Sedov (J. Appl. Math. Mech. (PMM), 1963, 27, 597-629). In this paper we do one more step and derive formulas for the elastic modulus tensors for all symmetry groups from the Lokhin-Sedov results. The tensor basis obtained in this way has an advantage of being built upon the same tensors that are used in construction of nonlinear tensor functions. One consequence of the formulas derived is that the number of types of anisotropic elastic behaviors is ten. There is a long- …

Nebraska Summary: S1256 Fendt 722 Vario Gen7, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Nebraska Tractor Test: 2266 John Deere 9rx 640, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Nebraska Tractor Test: 2262 John Deere 9r 540, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Nebraska Tractor Summary: S1257 Fendt 724 Vario Gen7, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Nebraska Tractor Test: 2273 John Deere 5130m Powrquad Plus, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Nebraska Summary #1274: New Holland T7.340 Hd, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Nebraska Summary #1297: Fendt 724 Vario Gen 7.1, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Dome Tester, Clark Bates, Nikolas M. Kulin

Williams Honors College, Honors Research Projects

We are reconfiguring and modifying the previously built dome tester to be more user friendly and mechanically applicable. This has a long-term goal of being a usable teaching tool for manufacturing education within the college of engineering and polymer sciences. The dome tester pushes a metal dome into a clamped sheet of metal to test its forming limits and where necking occurs. We have implemented a better method of viewing the sheet sample as it is being deformed, and improved measuring methods for the distance a sample is deformed. By introducing these changes in conjunction with improved documentation of the …

Rankine Cycle Investigation On Meeting Power And Thermal Requirements Of High-Speed Aircraft, Jacob J. Spark

Browse all Theses and Dissertations

This work is investigating a dual mode Rankine cycle for aircraft applications, specifically meeting vehicle thermal and power requirements. This multiconfigurational approach allows the Thermal Management System (TMS) to be controlled based on aircraft needs. In this design, waste heat is removed from critical areas of the aircraft (e.g., propulsion, structure, subsystems) using the fuel as a heat sink. Hot fuel is then forced through a heat exchanger actively boiling water. The vapor byproduct is fed to a turbine coupled to a generator, providing power. The low-pressure steam is then condensed using cold fuel drawn from its tank; however, when …

Modeling Thermal Radiation In Combustion Environments: Progress And Challenges, Sandip Mazumder, Somesh P. Roy

Mechanical Engineering Faculty Research and Publications

Modeling thermal radiation in combustion environments can be extremely challenging for two main reasons. First, the radiative transfer equation (RTE), which is the cornerstone of modeling radiation in such environments, is a five-dimensional integro-differential equation. Second, the absorption and scattering coefficients of molecular gases and particulates prevalent in combustion environments oscillate strongly with the wavenumber (or wavelength), i.e., the medium is strongly nongray, requiring the solution of the RTE for a large number of wavenumbers. This article reviews the progress that has been made in this area to date with an emphasis on the work performed over the past three …

Aerosol Synthesis Of Tungsten Bronze Particles For Nir Shielding, Hao Tu

Theses and Dissertations

This dissertation emphasizes the need for efficient energy use in buildings and transportation due to global warming and the energy crisis. It suggests that improving energy efficiency can help reduce energy consumption and emissions and support sustainability. The dissertation introduces various transparent materials that can block near-infrared (NIR) radiation from solar radiation to save energy and money, and it highlights the growing market value of such products. The dissertation compares tungsten bronze with other NIR shielding materials and shows its advantages. The dissertation introduces a cheap and environmentally friendly method for continuously producing tungsten bronze particles via aerosol synthesis. Particle …