Digital Commons Network^™

Numerical Modeling Of Thermal Runaway In Lithium-Ion Batteries Using Decomposition Kinetics And Inter-Cell Contact Resistance, Shehzad Khan

College of Graduate Studies: Theses & Dissertations

Lithium-ion batteries (LIBs) are central in numerous high-demand applications due to their high energy density and prolonged cycle life. Despite these advantages, their susceptibility to thermal runaway (TR) poses a significant safety risk, with the potential for catastrophic failures. This study focuses on the thermal behavior of prismatic lithium-ion cells, using a finite volume-based partial differential equation (PDE) solver developed in MATLAB and JULIA to model TR behavior. This solver accurately simulates transient behaviors, convection, diffusion, and source terms across various coordinate systems. By engaging in a series of increasing complex case studies, this research aims to identify the critical …

Investigation Of Topologically Protected Wave Propagation Near Dirac-Like Cones In Acoustic Metamaterials, Md Arif Iqbal Khan

College of Graduate Studies: Theses & Dissertations

This study presents a novel approach to investigate an exceptionally rare acoustic phenomenon – topologically protected wave propagation (TPWP) within a solid-solid domain. While previous research has attempted to unravel the physics behind this phenomenon, most efforts have been grounded in the framework of condensed matter physics and quantum mechanics often requiring complex geometries to realize TPWP in solid-fluid interactions. In contrast, this thesis introduces a geometric tuning method that enables the achievement of TPWP with simpler geometric configurations within a solid-solid domain. Rather than explaining by the quantum trio - quantum anomalous hall effect, quantum valley hall effect, and …

Mathematical Modeling Of Coupled Heat And Mass Transfer In Metal-Hydride Hydrogen Storage Systems, Muhammad Hasnain

College of Graduate Studies: Theses & Dissertations

As a promising clean energy carrier hydrogen has recently gained significant interest, but its efficient and safe storage is a major challenge. Compared to the gaseous state and liquid state, metal hydrides (MH) offer a potentially more effective storage approach for hydrogen. However, the main challenge in this approach is the low thermal conductivity of the MH bed that leads to low heat transfer and ultimately to higher charging and discharging times. The purpose of this work is to develop an in-house comprehensive heat and mass transfer model for hydrogen sorption in MH reactors to simulate the dynamic behavior of …

The Discharge-Induced Polarity-Dependent Propagation Characteristics Of A Strong Shock Wave, Anna Markhotok

Physics Faculty Publications

The specifics of a shock wave propagation down a positive column of a DC discharge in molecular chemically inert gases has been investigated. It was shown that axial gradients caused by the imbalance in the charged particle momentum transfer to the gas molecules can be a reason for the shock velocity dependence on the electric field direction. In pure nitrogen gas, the calculated shock velocity difference of up to 13.5% is in good agreement with the 12% value obtained in the experiment. A returning gas flow organizing in the discharge as a possible mechanism for an extended shock structure and …

Three-Dimensional Laser-Assisted Printing Of Structures From Nanoparticles, Heng Pan, Chinmoy Podder, Wan Shou, Xiaowei Yu

Patents

A method for manufacturing a component comprising bombarding nanoparticles in a dispersion with a laser to transform the ligand and cause the nanoparticles to drop out of the dispersion and deposit onto a substrate; and bombarding additional nanoparticles in the dispersion with the laser to transform the ligand and cause the nanoparticles to drop out of the dispersion and deposit onto the nanoparticles previously deposited out of the dispersion.

Zno Varistors—Preparation Of Nano And Micro Sized Powders By Mechanical Methods For Low And High Voltage Varistors, Maura Kelleher

Books/Book Chapters

ZnO-Bi2O3-Sb2O3 varistors are as essential today as they have been since their discovery five decades ago. Their role is to protect other electronic components against oncoming surges of electrons and survive. The demands on varistors are increasing. Electronic components are becoming smaller and more sensitive, and the metal oxides from which varistors are made are precious. Every aspect of their structure (macro, micro, nano and atomic) determines how they perform and survive. Each stage and variable within the powder metallurgy process is important. The mechanical methods in preparing nano and micro sized metal oxide powders are outlined in this chapter.

Sensor Tasking For Low Earth Orbit Objects: Leveraging Space Sensor Data For Ground-Based Optical Observations, Smriti Nandan Paul, Hang Woon Lee

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Because of recent advancements in space technologies, easier and more economical access to space, and an increase in commercial interests, the near-Earth space environment has witnessed an exploding number of objects being put into orbit. In particular, the low Earth orbit (LEO) region is at an increased risk of orbital collisions from large satellite constellation projects. Thus, monitoring LEO objects for space situational awareness and space traffic management has become increasingly imperative. In this paper, we use the concept of limited-CDF (cumulative distribution function) surface and mutual information for designing sensor tasking algorithms focusing on regular observation of known catalog …

Damage Initiation Of 15v38 Steel Bar During Square-To-Round Hot Rolling Process, Siva Sai Krishna Dasari, Henry Adekola Haffner, K. Chandrashekhara, Mario F. Buchley, Simon N. Lekakh, Ronald J. O'Malley

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Hot rolling processes have been extensively used to produce round bars by reducing the cross-sectional area of continuously cast steel. The current trend toward increasing productivity often requires a more aggressive reduction per pass. Establishing safe and optimized hot rolling parameters must be determined to avoid damage while deforming the specific steel composition. Understanding the damage mechanism during the metal forming process is vital for product quality. Herein, a combined experimental and simulation approach is developed to track the evolution potential damage during hot bar rolling. Hot tension tests are conducted on as-cast vanadium micro alloyed 15V38 steel at different …

Optimal Tilt-Wing Evtol Takeoff Trajectory Prediction Using Regression Generative Adversarial Networks, Shuan Tai Yeh, Xiaosong Du

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Electric vertical takeoff and landing (eVTOL) aircraft have attracted tremendous attention nowadays due to their flexible maneuverability, precise control, cost efficiency, and low noise. The optimal takeoff trajectory design is a key component of cost-effective and passenger-friendly eVTOL systems. However, conventional design optimization is typically computationally prohibitive due to the adoption of high-fidelity simulation models in an iterative manner. Machine learning (ML) allows rapid decision making; however, new ML surrogate modeling architectures and strategies are still desired to address large-scale problems. Therefore, we showcase a novel regression generative adversarial network (regGAN) surrogate for fast interactive optimal takeoff trajectory predictions of …

Sensor Tasking Strategies For Space-Based Observers In The Cislunar Environment, Smriti Nandan Paul, Roshan Thomas Eapen, Puneet Singla

Mechanical and Aerospace Engineering Faculty Research & Creative Works

The cislunar space environment has witnessed an increase in activities, and future projections indicate significant growth in object population. Consequently, it becomes crucial to monitor these objects for space domain awareness (SDA) purposes. As the number of objects surpasses the available observers, meticulous sensor tasking becomes essential. This paper focuses on designing and exploring strategies for observing and keeping custody of known objects in cislunar space. Optical space-based telescopes, combined with lunar ground-based telescope, are employed for sensor tasking of cislunar objects residing in valuable orbits. The proposed research aims to address the following key points: (1) examination of the …

L∞ Bounds For Transient Growth In Repetitive And Iterative Learning Control Systems, Douglas A. Bristow, John R. Singler

Mechanical and Aerospace Engineering Faculty Research & Creative Works

This paper revisits the problem of large transient growth in Iterative Learning Control (ILC) and Repetitive Process Control (RPC) systems. In ILC and RPC problems a process is repeated iteratively, with new control calculations occurring in between each iteration. Large transient growth refers to the propensity of some control algorithms to grow error exponentially before eventually converging. While robust monotonic convergence algorithms (in which monotonic convergence is guaranteed usually in exchange for a small loss in performance) have largely eliminated the concern for large transient growth in ILC, similar results cannot always be obtained in RPC. The emergence of additive …

Human Arm Stiffness Estimation Method Developed For Overground Physical Interaction Experiments: Experimental Validation And Perspectives For Future Applications, Tarani Kanth Kamma

Masters Theses

"To build a physically interactive robot for overground applications, it is crucial to first understand the biomechanics of humans underlying overground physical human-robot interaction (pHRI) tasks. Estimating human arm stiffness during overground interactive tasks is a promising first step toward this goal. For this, an arm stiffness estimation technique was developed in our previous works that consider the unique challenges involving overground pHRI, such as the need to estimate the arm stiffness from a short duration of data with fewer repetitions. In this work, our stiffness estimation method is further validated with a passive spring setup with known stiffness values, …

Machine Learning-Assisted Multiscale Simulation And Design Optimization Of Composite Jackets Under Low-Velocity Impacts, Masoud Mohammadi

Graduate Theses, Dissertations, and Problem Reports (ETD)

This research presents the development of a data-driven machine learning-assisted approach to simulate and optimize the design of composite materials subjected to low-velocity impacts. It focuses on a specific type of hybrid composite comprised of fiberglass and Kevlar fabrics stitched with Kevlar threads. The study begins by creating a multiscale finite element simulation for the composite under a low-velocity impact, which operates across three scales: microscale, mesoscale, and macroscale. This simulation accepts various inputs, such as different layer configurations and orientations, and provides impact outputs including maximum load and energy absorption capacity and displacement at failure.

Python and MATLAB scripts …

On Uncertainty For Ill-Posed Robot Decision Problems, Jared Joseph Beard

Graduate Theses, Dissertations, and Problem Reports (ETD)

As robots adopt more real world responsibilities, they will be expected to solve more complicated problems. In some cases limited prior knowledge will result in unmodelled environmental conditions; in others, multiple users may have competing perspectives on how to frame a decision problem. Many existing frameworks, namely Markov decision processes (MDP) presuppose users have identified a specific problem with models sufficient to solve or learn a problem. If we wish to extend MDPs to novel problems or those heavily dependent on user feedback, autonomous decision makers must be able to identify limitations in how a given problem is framed and …

Parametrization Of Fluid Models For Electrical Breakdown Of Nitrogen At Atmospheric Pressure, Shirshak K. Dhali

Electrical & Computer Engineering Faculty Publications

In the transient phase of an atmospheric pressure discharge, the avalanche turns into a streamer discharge with time. Hydrodynamic fluid models are frequently used to describe the formation and propagation of streamers, where charge particle transport is dominated by the creation of space charge. The required electron transport data and rate coefficients for the fluid model are parameterized using the local mean energy approximation (LMEA) and the local field approximation (LFA). In atmospheric pressure applications, the excited species produced in the electrical discharge determine the subsequent conversion chemistry. We performed the fluid model simulation of streamers in nitrogen gas at …

Rf And Mechanical Design Of A 915 Mhz Srf Cavity For Conduction-Cooled Cryomodules, G. Ciovati, A. Castilla-Loeza, G. Cheng, J. Henry, J. Rathke, J. Vennekate, K. Harding, T. Schultheiss, J. Lewis

Physics Faculty Publications

Conduction-cooled SRF niobium cavities are being developed for use in compact, continuous-wave electron linear accelerators for a variety of industrial applications. A 915 MHz two-cell cavity has been designed to achieve an energy gain of 3.5 MeV. The design of the cell shape aims at minimizing the peak surface magnetic field. Field flatness is achieved by adjusting the length of the outer end half-cells. The higher-order mode analysis shows that absorbers are not required for a moderate beam current of 5 mA. One of the beam tubes has two side-ports for insertion of coaxial fundamental power couplers. The mechanical design …

Dynamic Analysis And Experimental Verification Of Flexible Unbalance Rotor Supported By Two Identical Journal Bearings, Omar Ahmed, Hussein Sayed, T.A. El-Sayed

Trends in advanced sciences and technology

Abstract BACKGROUND: Analyzing the vibrations for rotor-bearing systems is a critical issue in the field of rotor dynamics. It is crucial to identify rotary machine vibrations, behaviors, and stability conditions. The main causes of vibration in rotating machinery are unbalanced masses, misalignment, mechanical looseness, shaft cracks, and other defects. METHODS: This paper investigates the experimental verification of a theoretical model, using a steel shaft with a disc set at the midpoint, supported by two symmetric fluid film bearings. The study examines the effect of unbalance on the dynamic behavior of the rotor and its vibration characteristics. The experimental investigation involved …

Energy And Exergy Analysis Of Multi-Stage Axial Flow Compressor: Degree Of Reaction, Inlet Temperature, And Pressure Ratio Impacts, Mohamed Abdelaal, Rafea Mohamed Abd El-Maksoud, Nazih Noaman Bayomi

Trends in advanced sciences and technology

This paper presents a comprehensive energy and exergy analysis of a multistage axial compressor, specifically examining a 12-stage model to assess the impact of varying inlet temperatures, degrees of reaction, and pressure ratios. This study contributes to the ongoing efforts to optimize compressor technology for better performance and reduced energy consumption, emphasizing the importance of parameter selection in achieving desired operational outcomes. In the current research, the performance of the axial compressor was studied from an energy and exergy point of view while changing the parameters previously mentioned in detail as stages and rotors due to the lack of previous …

Enhancement Of The Performance And Emission Attributes For The Diesel Engine Using Diesel-Waste Cooking Oil Biodiesel And Graphene Oxide Nanofluid Blends Through Response Surface Methodology, Medhat Elkelawy, E A El Shenawy, Hagar Alm-Eldin Bastawissi, Mahmoud M. Shams

Mansoura Engineering Journal

This study examined how diesel fuel and waste-cooked oil (WCO) biodiesel blends added by various concentrations of graphene oxide (GO) nanoparticles can effect on the performance and emission characteristics of constant-speed, four-stroke, single-cylinder, water-cooled diesel engines. The GO nanoparticles concentrations are 50,100 and 150 ppm dispersed in different diesel-WCO biodiesel blends are pure diesel fuel (B0), 20% WCO biodiesel and 76% diesel fuel (B20), and 40% WCO biodiesel and 56% diesel fuel (B40). In addition 4% toluene in all blends which used as a surfactant. The diesel engine fueled with these blends and operated at various engine loads are 2, …

Dynamics Of A 3-D Inlet/Isolator Measured With Fast Pressure-Sensitive Paint, Andrew N. Bustard, Mark E. Noftz, Mitsugu Hasegawa, Hirotaka Sakaue, Joseph S. Jewell, Nicholas J. Bisek, Thomas J. Juliano

Publications

Fast pressure-sensitive paint (PSP) was applied to an inlet/isolator designed using the Osculating Internal Waverider Inlet with Parallel Streamlines (OIWPS) method. The dorsal isolator surface pressure was measured using anodized-aluminum PSP through transparent cast acrylic that makes up the ventral portion of the isolator. Temperature-sensitive paint was utilized to correct for the PSP’s temperature sensitivity. The model was tested under Mach 5.7 flow at Re = 8.5 ×106 /m and 10.2 ×106 /m in the AFOSR–Notre Dame Large Mach-6 Quiet Tunnel (ANDLM6QT) under conventional noise conditions. Flow phenomena, such as shocks originating in the inlet and flow separation at the …

Analysis Of Variations In Flow-Independent Liquid Jet-In-Crossflow Injections, Michael Scott

Honors Undergraduate Theses

Liquid fuel injection is a critical mechanism for the deliverance of liquid fuel in contemporary aircraft propulsion combustion systems due to its outsized influence in providing optimal combustion conditions and improving overall aircraft efficiency and performance. Despite this, these liquid jet in crossflow (LJIC) systems are highly variable due to conditions in the jet and the surrounding airflow, leading to variability in performance behavior and inconsistency in fuel mixing and combustion efficiency. This has prompted the introduction of solid pintile obstructions of novel designs to provide a more flow-independent fuel injection scheme and decrease variability of the jet properties against …

Methodology For Parameter Determination For Simulation Software, Aaron Flood

Doctoral Dissertations

"This research aims to present a methodology for optimizing input datasets to increase the accuracy of mathematical models and accelerate their application to engineering problems. To accomplish this goal, this work focused on the application of mathematical models to metal additive manufacturing (AM), specifically the thermal history of laser directed energy deposition (DED) of aluminum alloys. The initial steps of this body of work were to develop a mathematical model that is capable of simulating the metal AM process and applying it to the laser DED of aluminum. It was validated using the well characterized material Ti-64 and shown to …

Kinetic Modeling And Simulations Of Plasma-Surface-Dust Interactions For Lunar Exploration, David Clifford Lund

Doctoral Dissertations

"Due to the recent relevance of NASA’s focus on lunar missions, a better understanding of the lunar plasma-surface-dust environment is vital for their success. The lunar surface, devoid of an atmosphere and a global magnetic field, is directly exposed to solar radiation and solar wind plasma. This exposure leads to the electrical charging of the lunar surface due to the bombardment of solar wind plasma and the emission/collection of photoelectrons. Therefore, this research developed accurate and efficient computational models of plasma-surface-dust interactions and extend a legacy simulation code, namely the Immersed-Finite-Element Particle-in-Cell (IFE-PIC), to a parallel version: Parallel Immersed-Finite-Element Particle-in-Cell …

Hydrogen Production From Microbial Electrolysis Cells Powered With Microbial Fuel Cells, Dina Aboelela

Biochemical Engineering

No abstract provided.

Depressurization Characteristics Of Steam-Based Reciprocating Vacuum Pump, Hongling Deng

Dissertations

This dissertation introduces a novel vacuum technology that leverages low-pressure saturated steam and cooling-controlled condensation, offering an efficient way to utilize low-grade thermal energy sources like waste heat, steam, or solar energy. At the heart of this technology is a unique duo-chamber vacuum pump system, featuring a reciprocating piston and a heat-conductive wall, designed to generate a vacuum through steam-condensation and cooling processes.

The core of this research lies in developing and validating mechanistic models for the steam-condensation depressurization process, a complex phenomenon involving phase change and transport mechanisms. Prior to this work, these mechanisms were not sufficiently modeled or …

The Interaction Of The Cotton Piece With The Piles Of The Scrabble Cotton Drum, Fazliddin Egamberdiev, Ilkhom Abbazov, Oybek Kholmuratov, Rashid Kaldybaev

Technical science and innovation

This article presents the results of an analytical study of the process of loosening and cleaning raw cotton from small debris by pileging working bodies of purifiers, on the basis of which directions for further research were chosen to optimize the parameters of the developed pile drum with spherical piles and rubber strips. Cotton entering production contains impurities. The processes of loosening and cleaning the fiber shreds are key in the initial stages of ginning, as they prepare the raw cotton for ginning and directly affect the reliability, productivity of these processes and the quality of the resulting fiber. Weed …

Adaptation Algorithm For Self-Tuning Of Parameters Of Models Of Multi-Stage Flotation Processes, Nilufar Sharifzhanova, Maksadhan Yakubov, Francesco Gregoretti

Technical science and innovation

Modern methods for solving problems of planning the execution of batches of tasks in multi-stage systems are characterized by the presence of restrictions on their dimensionality, the impossibility of guaranteed obtaining better results in comparison with fixed packages for different values of the input parameters of the problem. In the article, the author solved the problem of optimizing the composition of job packages running in multi-stage systems using the branch and bound method. Research has been carried out on various ways to form package execution orders tasks in multi-stage systems (heuristic rules for ordering packages tasks in the sequence of …

Programming A Numerical Model Of Spherical Propagation Of Electric Discharge In Liquid, Mukhiddin Kushshaevich Khudjaev

Technical science and innovation

The subject of research is the determination of the hydrodynamic parameters of a liquid in the process of an electric discharge in a liquid. A numerical algorithm was constructed and a program was drawn up to determine the hydrodynamic parameters of a liquid in the process of an electric discharge in a liquid for a spherical problem. In the numerical solution of the problem, a uniform rectangular grid was used. Some results of computational experiments are presented.

Multi-Mode Regulation Of The Drying Process Of Industrial Gas, Isamidin Xakimovich Sidikov Pr, Nashvandova Gulruxsor Murot Qizi Phd

Technical science and innovation

Currently, much attention is paid to the issue of energy efficiency of gas processing enterprises. The continuous growth of world prices for energy resources requires constant improvement of the management system, providing the most optimal conditions for the flow of technological processes. A conceptual model of the heat-mass transfer process occurring in the absorber as an object of research has been developed, which characterizes the relationship of the variables involved in the drying process of natural gas, control, measurable and immeasurable, as well as controlled parameters have been selected, which are used to develop and study a mathematical model of …

Reducing Food Scarcity: The Benefits Of Urban Farming, S.A. Claudell, Emilio Mejia

Journal of Nonprofit Innovation

Urban farming can enhance the lives of communities and help reduce food scarcity. This paper presents a conceptual prototype of an efficient urban farming community that can be scaled for a single apartment building or an entire community across all global geoeconomics regions, including densely populated cities and rural, developing towns and communities. When deployed in coordination with smart crop choices, local farm support, and efficient transportation then the result isn’t just sustainability, but also increasing fresh produce accessibility, optimizing nutritional value, eliminating the use of ‘forever chemicals’, reducing transportation costs, and fostering global environmental benefits.

Imagine Doris, who is …