Digital Commons Network^™

A Rubber Membrane Analogy For The Study Of Shafts In Torsion., Myron D. Bruns

Masters Theses

"The thesis presents a review of literature giving reference to several books which present the many and varied methods of determining the shearing stresses in shafts. However, no reference was found that used a rubber membrane analogy similar to that used in th is thesis. The theory of torsion, the membrane theory, and its analogy have been presented for a better understanding of the subject. Illustrations are used freely for clarity.

Analytical methods and solutions are given for two problems. The first method is that of writing a Saint-Venant stress function and satisfying the necessary conditions for it to be …

Forced Convection Heat Transfer Coefficients And Induction Heating, Max Edwin Light

Masters Theses

“The purpose of this study was to design and build an apparatus to experimentally determine the convective heat transfer coefficients for water flowing in a horizontal tube at turbulent flow. Also it was planned to use the apparatus to investigate the spatial dependence of energy deposition by induction heating.

An instrument and measuring techniques were developed that gave reasonable correlations between experimentally determined heat transfer coefficients and values calculated from generally accepted heat transfer relationships developed by other experimenters. Most of the calculated values were within ± 10% of the experimental values for a wide range of flow rates.

It …

The Effects Of Granular Size On The Thermal Conductivity Of Sand, Kanubhai M. Patel

Masters Theses

"The thermal conductivity of granular materials can be determined by the Thomas method. This method was used here to determine the effects of granular size on the thermal conductivity of sand. A river sand was secured and screened. The sand retained between the Tyler Standard Screen Scale, mesh 10 and 14, 14 and 28, 28 and 40, 40 and 48, 48 and 60, and below mesh 60, was used for tests.

The thermal conductivity for the above six samples obtained by the author coincide fairly well with published data.

It is reported in the International Critical Tables that the thermal …

Generalized Programs For Heat Transfer Analysis., Ceylung Chu

Masters Theses

"This report presents numerical methods for calculating temperature distributions in any physical system in which heat transfer is taking place. The syste.11 may be at either a steadystate condition or a transient condition. The temperature distribution may itself be or primary interest, or it may be used further to calculate the flow or heat or thermal stress.

The system under investigation is divided into a certain number of subdivisions, or so-called "regions". A reference point (node point) will be taken as representative for the region which includes that point. The temperature at the "node point11 is taken to be the …

Experimental Evaluation Of Thermal Stresses On The Outer Surface Of A Thick-Walled Tube., Vinodray T. Patel

Masters Theses

"In this investigation an attempt has been made to measure thermal stresses on the outer surface of a thick- walled tube. The inside surface was heated by steam passing through the tube while the outer surface was cooled by water. Two temperature compensated strain gages were used to measure strains in the tangential and axial directions respectively. The advantage of using this type of strain gage is to avoid the use of a dummy gage to compensate for the temperature effect.

The analytical solution to the problem was derived and the values of thermal stresses were calculated theoretically and compared …

A Theoretical And Experimental Study Of The Stress Distribution In An Infinite Plane Shrink-Fitted On Four Circular Elastic Pins, Charles H. White

Masters Theses

"The purpose of this study is to show a general method of solution for multiple inclusions in an infinite plane. The shrink-fitting of an infinite plane upon the inclusions, or pins, will be simulated by force-fitting the pins into a large sheet of birefringent material, to obtain an experimental verification of the analytical solution.

The problem to be approached is that of four circular elastic pins shrink-fitted in an infinite plane. The method of superposition will be used, and the stresses at any point in the plane found with respect to a common origin of coordinates. It will first be …

The Design, Construction, And Operation Of A Conducting Field Analog Computer., Richard T. Johnson

Masters Theses

"The purpose of this investigation is to design and construct a simple conducting field analog to solve problems described by the two-dimensional Poisson or Laplace equations. Decisions concerning choice of conducting media, construction of problem models, and design and construction of a specialized power supply with instrumentation were based on the results of previous experiments. Several problems are solved using the designed apparatus. Partial solutions to these problems are displayed in graphical form.

The greatest deviation of the experimental results from iterative values was consistently less than 8%. In most cases the deviation was less than 6%. The console arrangement …

Test 855: Allis-Chalmers D-21 (Diesel), Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF TEST REPORT GENERAL CONDITIONS East tractor is a production model equipped for common usage. Power consuming accessories can be disconnected only when it is convenient for the operator to do so in practice. Additional weight can be added as ballast if the manufacturer regularly supplies it for sale. The static tire loads and the inflation pressures muse conform to recommendations in the Tire Standards published by the Society of Automotive Engineers. PREPARATION FOR PERFORMANCE RUNS The engine crank case is drained and refilled with a measured amount of new oil conforming to specifications in the operator’s manual. The …

Test 854: Massey-Ferguson Mf 25 (Diesel), Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF TEST REPORT GENERAL CONDITIONS East tractor is a production model equipped for common usage. Power consuming accessories can be disconnected only when it is convenient for the operator to do so in practice. Additional weight can be added as ballast if the manufacturer regularly supplies it for sale. The static tire loads and the inflation pressures muse conform to recommendations in the Tire Standards published by the Society of Automotive Engineers. PREPARATION FOR PERFORMANCE RUNS The engine crank case is drained and refilled with a measured amount of new oil conforming to specifications in the operator’s manual. The …

Test 853: John Deere 4020 Lpg, Nebraska Tractor Test Lab

Nebraska Tractor Tests

No abstract provided.

Test 852: John Deere 3020 Lpg, Nebraska Tractor Test Lab

Nebraska Tractor Tests

No abstract provided.

Test 850: John Deere 4020 Gasoline, Nebraska Tractor Test Lab

Nebraska Tractor Tests

No abstract provided.

Test 851: John Deere 3020 Gas, Nebraska Tractor Test Lab

Nebraska Tractor Tests

No abstract provided.

Test 849: John Deere 4020 Diesel, Nebraska Tractor Test Lab

Nebraska Tractor Tests

No abstract provided.

Test 848: John Deere 3020 Diesel, Nebraska Tractor Test Lab

Nebraska Tractor Tests

No abstract provided.

Test 847: Oliver 1900 Series B Diesel 4wd, Nebraska Tractor Test Lab

Nebraska Tractor Tests

No abstract provided.

Test 846: Oliver 1800 4wd, Nebraska Tractor Test Lab

Nebraska Tractor Tests

No abstract provided.

Test 845: Ford 5000 (Diesel), Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF TEST REPORT GENERAL CONDITIONS East tractor is a production model equipped for common usage. Power consuming accessories can be disconnected only when it is convenient for the operator to do so in practice. Additional weight can be added as ballast if the manufacturer regularly supplies it for sale. The static tire loads and the inflation pressures muse conform to recommendations in the Tire Standards published by the Society of Automotive Engineers. PREPARATION FOR PERFORMANCE RUNS The engine crank case is drained and refilled with a measured amount of new oil conforming to specifications in the operator’s manual. The …

Analysis Of The Transient Response Of A Flat Rotating Disk By Generalized Transforms, Kenneth Wayne Chase

Theses and Dissertations

The object of this thesis was to lay a foundation for a comprehensive study of the dynamic response of rotating members. This initial phase of the study includes a theoretical investigation and proposes experimental techniques for the determination of the stresses and strains in a thin, rotating disk with a concentric hole, subjected to transient shaft inputs. There are many practical applications of this problem including computor memory storage disks, turbine rotors, grinding wheels, saw blades, gears, optical reflectors, and solar sails for space vehicles.

Heat Flux Measurement By Miniature Calorimeters, Gary Rex Coffin

Theses and Dissertations

During recent years an increasing number of technical firms and manufacturers have begun to specify heat flux, energy input per unit area per unit time, as a testing and designing criteria. This change in the boundary condition (to heat flux from temperature excess or others) evolved from the idea that each material has a characteristic burning temperature. Therefore, the rate of ablation or burning depends mainly upon the rate of energy input into the specimen, and not its temperature. Thus, the need for a flux measuring device became more acute.

Radiant Flux Distribution From Concave Radiation Sources, Richard K. Duke

Theses and Dissertations

In order to analyse the radiant heat transfer characteristics of a concave source, two vital concepts must be clearly understood. The first is called the apparent emissivity Ea and is a function of both the local total emissivity E and of the geometry of the source. Although the total emissivities of ordinary substances range between zero and one, the two extremeties never occur. Surface emissivities which approach these values in the limit, must be created mechanically from materials in the range 0

Test 844: Ford 2000 Super Dexta Diesel, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF TEST REPORT GENERAL CONDITIONS East tractor is a production model equipped for common usage. Power consuming accessories can be disconnected only when it is convenient for the operator to do so in practice. Additional weight can be added as ballast if the manufacturer regularly supplies it for sale. The static tire loads and the inflation pressures muse conform to recommendations in the Tire Standards published by the Society of Automotive Engineers. PREPARATION FOR PERFORMANCE RUNS The engine crank case is drained and refilled with a measured amount of new oil conforming to specifications in the operator’s manual. The …

Test 842: Ford 6000 (Gasoline), Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF TEST REPORT GENERAL CONDITIONS East tractor is a production model equipped for common usage. Power consuming accessories can be disconnected only when it is convenient for the operator to do so in practice. Additional weight can be added as ballast if the manufacturer regularly supplies it for sale. The static tire loads and the inflation pressures muse conform to recommendations in the Tire Standards published by the Society of Automotive Engineers. PREPARATION FOR PERFORMANCE RUNS The engine crank case is drained and refilled with a measured amount of new oil conforming to specifications in the operator’s manual. The …

Test 843: Ford 6000 (Diesel), Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF TEST REPORT GENERAL CONDITIONS East tractor is a production model equipped for common usage. Power consuming accessories can be disconnected only when it is convenient for the operator to do so in practice. Additional weight can be added as ballast if the manufacturer regularly supplies it for sale. The static tire loads and the inflation pressures muse conform to recommendations in the Tire Standards published by the Society of Automotive Engineers. PREPARATION FOR PERFORMANCE RUNS The engine crank case is drained and refilled with a measured amount of new oil conforming to specifications in the operator’s manual. The …

Transient Response Of Linear Undamped And Lightly Damped Lumped Spring-Mass Systems By Graphica Techniques, Richard O. Brooks

Mechanical Engineering ETDs

Responsive motions of linear undamped and lightly damped lumped spring mass systems subjected to transient inputs can be determined by several methods. All these methods require solving of the differential equation in some manner. Practically all techniques for solving the differential equations involve higher mathematics.

Test 841: Oliver 1600 (Gasoline), Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF TEST REPORT GENERAL CONDITIONS East tractor is a production model equipped for common usage. Power consuming accessories can be disconnected only when it is convenient for the operator to do so in practice. Additional weight can be added as ballast if the manufacturer regularly supplies it for sale. The static tire loads and the inflation pressures muse conform to recommendations in the Tire Standards published by the Society of Automotive Engineers. PREPARATION FOR PERFORMANCE RUNS The engine crank case is drained and refilled with a measured amount of new oil conforming to specifications in the operator’s manual. The …

Test 840: Oliver 1600 Diesel, Nebraska Tractor Test Lab

Nebraska Tractor Tests

No abstract provided.

Test 839: Oliver 1800, Nebraska Tractor Test Lab

Nebraska Tractor Tests

No abstract provided.

A Study Of The Vibration Characteristics Of A Thin Shell Hyperbolic Paraboloid, Farrin W. West

Theses and Dissertations

Recent progress in structural engineering has been marked by the increased use of thin shells as load carrying members. In particular, shells of revolution have been widely utilized in the missile industry whereas shells of arbitrary shape have been incorporated in the architectural design of today's modern buildings. Missile applications have been extensively studied both statically and dynamically. However, architechural applications have generally been limited to the statics problem with little consideration being given to the dynamic behavior of these unique structures.

Test 838: Allis-Chalmers Series Ii D15 (Lpg), Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF TEST REPORT GENERAL CONDITIONS East tractor is a production model equipped for common usage. Power consuming accessories can be disconnected only when it is convenient for the operator to do so in practice. Additional weight can be added as ballast if the manufacturer regularly supplies it for sale. The static tire loads and the inflation pressures muse conform to recommendations in the Tire Standards published by the Society of Automotive Engineers. PREPARATION FOR PERFORMANCE RUNS The engine crank case is drained and refilled with a measured amount of new oil conforming to specifications in the operator’s manual. The …