Digital Commons Network^™

Test 1198: Kubota L 285 Diesel, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF TEST REPORT GENERAL CONDITIONS Each tractor is a production model equipped for common usage. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operator station. Additional weight can be added as ballast if the manufacturer regularly supplies it for sale. The static tire loads and the inflation pressures must conform to recommendations in the Tire Standards published by the Society of Automotive Engineers. PREPARATION FOR PERFORMANCE RUNS The engine crankcase is drained and refilled with a measured amount of new oil conforming to specifications in the operator’s manual. The fuel …

Test 1210: Case 1410 Power Shift (David Brown 1412 Hydra-Shift) Diesel, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF TEST REPORT GENERAL CONDITIONS Each tractor is a production model equipped for common usage. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operator station. Additional weight can be added as ballast if the manufacturer regularly supplies it for sale. The static tire loads and the inflation pressures must conform to recommendations in the Tire Standards published by the Society of Automotive Engineers. PREPARATION FOR PERFORMANCE RUNS The engine crankcase is drained and refilled with a measured amount of new oil conforming to specifications in the operator’s manual. The fuel …

Development Of Helicopter Flight Path Models Utilizing Modern Control Techniques, Alfred Fermelia

Doctoral Dissertations

"The nonlinear set of equations which represents helicopter motion are linearized about a prescribed nominal state. Once the linearized system is obtained it is validated by comparing the output of the nonlinear system to that of its linearized counterpart. Having obtained a linear model, linear system theory may then be applied in order to investigate the stability and control characteristics of the aircraft.

General techniques for simulating helicopter pilot response for inclusion in a flight path simulation program have been devised. To provide the desired flight goal, a nominal flight trajectory is obtained from an existing nonlinear model. With this …

Influence Of Initial Turbulence Intensity On The Heat And Moisture Transfer Through A Recirculated Air Curtain, Nguyen Quang Van

Doctoral Dissertations

"An air curtain is a directed jet of air separating a controlled space from an environment of different temperature and humidity. This investigation describes the development and verification of an eddy viscosity model which accounts for the influence of the initial turbulence intensity on the transfer of heat and moisture across a recirculated air curtain. The control of the turbulence intensity at the nozzle exit of an air curtain permits control of heat and moisture transfer and therefore the energy required to operate the air curtain.

Both theoretical and experimental studies were made of the recirculated air curtain. An explicit …

Bit Penetration Into Rock - A Finite Element Study, Jaw-Kuang Wang

Doctoral Dissertations

"A finite element approach has been developed to simulate bit penetration from bit-rock interaction to chip formation. A mathematical rock failure model, based on a review of the existing literature on rock tests, has been proposed to represent post-failure rock behavior and applied in the penetration simulations. The finite element program has been developed for two dimensional plane strain problems with non-linear material properties, geometrical nonlinearities and fracture. An anisotropic element as well as variable stiffness and stress release methods have been used. An iteration method, using an incremental approach, has been applied for continuous penetration and modifications of material …

Measurement Of Growth Rate To Determine Condensation Coefficients For Water Drops Grown On Natural Cloud Nuclei., A. M. Sinnarwalla, Darryl J. Alofs, J. C. Carstens

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Growth Rate Measurements Were Made for Water Drops Grown on Nuclei in Atmospheric Air Samples Taken in Rolla, Missouri. Rolla, Having a Population of 15,000 and Very Little Industry, is Relatively Free of Urban Pollutants. the Measurements Were Made in a Vertical Flow Thermal Diffusion Chamber at Supersaturations of 0. 5 and 1%. the Time to Grow from Near Dry Radius to the Final Radius (6 to 7. 5 Mu M) Was Measured. If One Assumes the Thermal Accomodation Coefficient is Unity, the Measurements Indicate an Average Value of 0. 026 for the Condensation Coefficient. the Temperature Ranged from 22. …

Transport Phenomena In Thermally Stratified Boundary Layers, D. W. Pepper, S. C. Lee

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Studies of heat, mass, and momentum transfer are made to analyze the formation of marine fogs in thermally stratified boundary layers in the atmosphere. The governing partial differential equations of continuity, momentum, temperature, and concentration are used to describe the transport phenomena. An additional equation of turbulence energy is introduced to account for the development of the turbulent motions. Simultaneous solution of this system of equations allows the turbulent exchange coefficients to be treated in the same way as all other dependent parameters. Verification of the theoretical approach is made by comparing the numerical predictions with wind tunnel simulations of …

Design And Analysis Of An Instrument System For Rheological Testing Of Whole Blood Samples, Robert Rimvydas Sinusas

Dissertations

The dissertation covers the conceptual design of a rheometer for testing whole blood samples through to the clotting state. While the design aims at increased measurement accuracy, the design employs well known technologies and available components.

The main reason for preoccupation with blood testing is that recent investigations have indicated that physiological disorders can be correlated with rheological properties of blood. The pursuit of an improved means of correlation is initiated with a survey of the rheological properties of blood. The relevance of these blood properties is then discussed. From this discussion a broader blood model is developed as a …

Plastic Relaxation Around Crack Tip In Composite Materials, Chung-Yen Huang

Mechanical Engineering ETDs

The concept of continuously distributed dislocations is used to investigate the mechanical behavior of fractured composite materials,

As a first approximation to the complicated physical configuration of a composite material, the current investigation concerns a simp1ified physical model by considering an elastic circular cylindrical inclusion imbedded and located in an infinite elastic medium such that an internal line crack starts from the interface and extends in the radial direction of the inclusion. The plastic zone spreads and extends from the crack tip when the entire system is subjected to a uniformly distributed shear load at infinity. This constitutes an anti-pane …

Dynamics Of Explosion Remnants In Earth-Orbits, Joseph T. Fuss

Mechanical & Aerospace Engineering Theses & Dissertations

Explosions in space produce particles that are hazardous to space vehicles. Some of these particles are not trackable and their locations must be predicted by dynamical methods.

This investigation sheds light on three different, areas, First, ignoring perturbations, the characteristics of a three dimensional envelope outlined by the sum of individual particle orbits is determined, Second, the distribution of the particles is found as a function of time, Finally, the movement, of the body via secular perturbations is investigated. Magnitudes of the explosion, the point of. detonation in the parent satellite's orbit, and the radius of perigee of the parent …

An Optimal Tracking System For Numerically Controlled Machine Tools, Stephen H. Neff

Mechanical Engineering ETDs

Conventional numerically controlled machine tools use straight line approximations for machining contoured surfaces or outlines. This thesis uses modern control theory to develop an optimal tracking system which will follow any surface defined by a second degree polynomial without resort to straight line approximation. To develop the optimal tracking system, the mathematical expressions required to define the dynamics of a two axis machine tool following a parabolic path are formulated. Next, the third order differential equation representing the slide, driven by a hydraulic motor which is controlled by an electrohydraulic servovalve, is changed into a first order matrix differential equation, …

An Experimental And Theoretical Study Of The Flow Phenomena Within A Vortex Sink Rate Sensor, Dashrath Khodidas Patel

Mechanical & Aerospace Engineering Theses & Dissertations

The objective of this investigation was to obtain a detailed description of the flow field within a vortex sink rate sensor and to observe the influence of viscous effects on its performance.

The sensor basically consists of a vortex chamber and a sink tube. The vortex chamber consists of two circular coaxial disks held apart, at their periphery, by a porous coupling. One circular disk has an opening to permit the mounting of the sink tube, in such a manner that the vortex chamber as well as the sink tube have a common axis of rotation.

Air was supplied radially …

1st Umr-Mec Conference On Energy Resources -- Entire Proceedings, University Of Missouri--Rolla

UMR-MEC Conference on Energy / UMR-DNR Conference on Energy

No abstract provided.

A Solar-Hydrogen Energy Conversion Scheme For Agricultural Use, R. L. Reisbig, Jack L. Boone, Gordon E. Weiss, Thomas Van Doren

UMR-MEC Conference on Energy / UMR-DNR Conference on Energy

A solar energy activated system is presented which can produce hydrogen and hydrogen-derived fuels (methanol) for use on farms. The device, named "solar-kine", also can produce fertilizer (anhydrous ammonia) as a byproduct of the hydrogen. A cost analysis shows that solar-kine may be mass-producible and sold to farmers for between $7,200 and $14,700. This is equivalent to giving the fanner energy at a price of $1.79 to $3.66 per million BTU's (in 1974 dollars). Presently (Spring, 1974) regular gasoline used in tractors at 43¢ per gallon, represents a cost to the farmer of $3.77 per million BTU's. As oil-based fuels …

Bulletin No 3883 - Dairying In W.A., Western Australian Department Of Agriculture

Bulletins - 3000 - 3999

Western Australia has a small dairy industry compared with its other rural production. However, the industry has consolidated over recent years.

Tree clearing and pasture development on existing holdings and the amalgamation of small dairy farms has led to a rapid increase in the area of pasture per farm. The trend in Western Australia is towards bigger herds, more efficient dairies, more fodder conservation and increasing production per cow and per· hectare.

Multiregional Interactions Between Energy And Transportation, Karen R. Polenske

Applications

Because of the number and complexity of the issues that will determine the use of coal by the electric-generating plants, an important asset of policy makers will be the availability of a method of analysis that allows for quick studies of many different combinations of assumptions and policies. The present prototype study is designed to show how the multiregional input-output model can be used to investigate each different assumption and policy alternative. For this paper, the analysis has necessarily been restricted to two issues. First, the results of using regional rather than national technologies in the model are assessed. This …

A Finite Element Analysis Of Unsymmetrically Laminated Rectangular Plates, Stanley F. C. Tseng

Mechanical & Aerospace Engineering Theses & Dissertations

The behavior of laminated plates with coupled extension-bending was investigated using the finite element method. A stiffness matrix for a rectangular element with 20 degrees of freedom was developed using a symbolic mathematics interpreter program. A finite element analysis program was written for the analysis of flat plate. Results i for plate deformations and internal moment distributions are compared with existing exact solutions or experimental data and excellent agreement is obtained.

Historical Sketch Of Tractor Testing, Nebraska Tractor Test Lab

Nebraska Tractor Tests

A historical sketch of Tractor Testing at the University of Nebraska-Lincoln. Lester F. Larsen. Engineer in charge since 1947, visits with George S. Round, Professor of Agricultural Communications at the University about individuals who made contributions to the successful program. He also reports on 1,155 tests conducted up to January I, 1974, and contrasts tractors of 1974 with those of 20, 30 or more years ago . Testing fee schedules are reviewed in a self-supporting project favorably known round the world.

Test 1157: John Deere 2630 And 2640 Diesel, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF TEST REPORT GENERAL CONDITIONS East tractor is a production model equipped for common usage. Power consuming accessories can be disconnected only when it is convenient for the operator to do so in practice. Additional weight can be added as ballast if the manufacturer regularly supplies it for sale. The static tire loads and the inflation pressures muse conform to recommendations in the Tire Standards published by the Society of Automotive Engineers. PREPARATION FOR PERFORMANCE RUNS The engine crank case is drained and refilled with a measured amount of new oil conforming to specifications in the operator’s manual. The …

Test 1159: White Field Boss 4-150 Diesel, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF TEST REPORT GENERAL CONDITIONS East tractor is a production model equipped for common usage. Power consuming accessories can be disconnected only when it is convenient for the operator to do so in practice. Additional weight can be added as ballast if the manufacturer regularly supplies it for sale. The static tire loads and the inflation pressures muse conform to recommendations in the Tire Standards published by the Society of Automotive Engineers. PREPARATION FOR PERFORMANCE RUNS The engine crank case is drained and refilled with a measured amount of new oil conforming to specifications in the operator’s manual. The …

Test 1160: Case 1270 Diesel, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF TEST REPORT GENERAL CONDITIONS East tractor is a production model equipped for common usage. Power consuming accessories can be disconnected only when it is convenient for the operator to do so in practice. Additional weight can be added as ballast if the manufacturer regularly supplies it for sale. The static tire loads and the inflation pressures muse conform to recommendations in the Tire Standards published by the Society of Automotive Engineers. PREPARATION FOR PERFORMANCE RUNS The engine crank case is drained and refilled with a measured amount of new oil conforming to specifications in the operator’s manual. The …

Test 1162: Steiger Bearcat Ii, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF TEST REPORT

GENERAL CONDITIONS

East tractor is a production model equipped for common usage. Power consuming accessories can be disconnected only when it is convenient for the operator to do so in practice. Additional weight can be added as ballast if the manufacturer regularly supplies it for sale. The static tire loads and the inflation pressures muse conform to recommendations in the Tire Standards published by the Society of Automotive Engineers.

PREPARATION FOR PERFORMANCE RUNS

The engine crank case is drained and refilled with a measured amount of new oil conforming to specifications in the operator’s manual. The …

Test 1163: Long 900 And 910 Diesel, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF TEST REPORT

GENERAL CONDITIONS

East tractor is a production model equipped for common usage. Power consuming accessories can be disconnected only when it is convenient for the operator to do so in practice. Additional weight can be added as ballast if the manufacturer regularly supplies it for sale. The static tire loads and the inflation pressures muse conform to recommendations in the Tire Standards published by the Society of Automotive Engineers.

PREPARATION FOR PERFORMANCE RUNS

The engine crank case is drained and refilled with a measured amount of new oil conforming to specifications in the operator’s manual. The …

Test 1165: Case 2670 Diesel, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF TEST REPORT

GENERAL CONDITIONS

East tractor is a production model equipped for common usage. Power consuming accessories can be disconnected only when it is convenient for the operator to do so in practice. Additional weight can be added as ballast if the manufacturer regularly supplies it for sale. The static tire loads and the inflation pressures muse conform to recommendations in the Tire Standards published by the Society of Automotive Engineers.

PREPARATION FOR PERFORMANCE RUNS

The engine crank case is drained and refilled with a measured amount of new oil conforming to specifications in the operator’s manual. The …

Test 1167: Allis-Chalmers 7060 Diesel, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF TEST REPORT GENERAL CONDITIONS East tractor is a production model equipped for common usage. Power consuming accessories can be disconnected only when it is convenient for the operator to do so in practice. Additional weight can be added as ballast if the manufacturer regularly supplies it for sale. The static tire loads and the inflation pressures muse conform to recommendations in the Tire Standards published by the Society of Automotive Engineers. PREPARATION FOR PERFORMANCE RUNS The engine crank case is drained and refilled with a measured amount of new oil conforming to specifications in the operator’s manual. The …

Test 1166: Allis-Chalmers 7040 Diesel, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF TEST REPORT GENERAL CONDITIONS East tractor is a production model equipped for common usage. Power consuming accessories can be disconnected only when it is convenient for the operator to do so in practice. Additional weight can be added as ballast if the manufacturer regularly supplies it for sale. The static tire loads and the inflation pressures muse conform to recommendations in the Tire Standards published by the Society of Automotive Engineers. PREPARATION FOR PERFORMANCE RUNS The engine crank case is drained and refilled with a measured amount of new oil conforming to specifications in the operator’s manual. The …

Test 1169: Steiger Tiger Ii Diesel (Also Steiger Panther Iii - St-320 Diesel), Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF TEST REPORT

GENERAL CONDITIONS

East tractor is a production model equipped for common usage. Power consuming accessories can be disconnected only when it is convenient for the operator to do so in practice. Additional weight can be added as ballast if the manufacturer regularly supplies it for sale. The static tire loads and the inflation pressures muse conform to recommendations in the Tire Standards published by the Society of Automotive Engineers.

PREPARATION FOR PERFORMANCE RUNS

The engine crank case is drained and refilled with a measured amount of new oil conforming to specifications in the operator’s manual. The …

Effect Of Sweeping Sinusoidal Excitation On Nonlinear Dynamic Systems., Md. Mosharraf Hossain

Masters Theses

"The response of viscous damped, cubic spring systems to excitations having exponentially varying frequency cannot be written in a closed form. This report summarizes a numerical investigation of hardening and softening cubic systems influenced by these excitations and provides information concerning the effects of varying viscous damping, system nonlinearity, and excitation sweep rate on system behavior near resonance. Results are reported in terms of maximum response attained during sweeping and the frequency at which maximum response occurs.

It has been found that if hardening cubic systems are subjected to sweeping excitations wherein the frequency sweeps down through resonance, the maximum …

Flow Field And Heat Transfer For Developing Flow Of Molten Glass In A Duct, Russell Ralph Beckmeyer

Masters Theses

"The molten glass flow (temperature range 1300 to 1500°C) in the entrance region of a duct was investigated with numerical methods. The mathematical model was restricted by assuming: (1) two dimensional, steady state, (2) Newtonian fluid, variable viscosity, and (3) Rosseland approximation. In addition, appropriate use was made of the fact that the Reynolds number is small and the Eckert number is very small. The inclusion of temperature dependent viscosity and a Rosseland approximation for radiation produced from the mass, momentum, and energy equations a system of coupled, nonlinear, partial differential equations which were solved by an iterative finite difference …

Test 1156: Allis-Chalmers 175 Gasoline, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF TEST REPORT GENERAL CONDITIONS East tractor is a production model equipped for common usage. Power consuming accessories can be disconnected only when it is convenient for the operator to do so in practice. Additional weight can be added as ballast if the manufacturer regularly supplies it for sale. The static tire loads and the inflation pressures muse conform to recommendations in the Tire Standards published by the Society of Automotive Engineers. PREPARATION FOR PERFORMANCE RUNS The engine crank case is drained and refilled with a measured amount of new oil conforming to specifications in the operator’s manual. The …