Digital Commons Network^™

Test 1310: Massey-Ferguson 2705 Diesel 24-Speed, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF THE TEST PROCEDURE

General

Tractors are tested at the University of Nebraska according to the Agricultural Tractor Test Code approved by the American Society of Agricultural Engineers and the Society of Automotive Engineers or official Nebraska test procedure.

The manufacturer selects the tractor to be tested and certifies that it is a stock model. Each tractor is equipped with the common power consuming accessories such as power steering, power lift pump, generator, etc., if available. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operating station. An official representative of …

Nucleation Experiments With Monodisperse Nacl Aerosols., Darryl J. Alofs, M. B. Trueblood, D. R. White, V. L. Behr

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Nucleation Experiments with Monodisperse NaCl Aerosols Showed Good Agreement with the Kohler Theory Relating the Critical Super-Saturation S//c to the Dry Size. Aerosols Produced by Condensing NaCl Showed the Same S//c as Those Produced by Evaporating Aqueous NaCl Solution Droplets. This Indicates that If There is an Energy Barrier in Going from a Dry NaCl Particle to a Solution Droplet, This Energy Barrier is Small. the Fact that the Evaporation Aerosol Particles Are Cubical Crystals and the Condensation Aerosols Are Amorphous Spheres is Shown to Make No Difference in the Nucleation Threshold. the Investigation Also Gives Insights into the Performance …

How To Select A Tractor, W T. Brown

Journal of the Department of Agriculture, Western Australia, Series 4

A look at some of the factors to be considered when choosing a tractor for your farm. There is no one answer

Test 1307: Deutz Dx-160 Diesel 24-Speed, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF THE TEST PROCEDURE

General

Tractors are tested at the University of Nebraska according to the Agricultural Tractor Test Code approved by the American Society of Agricultural Engineers and the Society of Automotive Engineers or official Nebraska test procedure.

The manufacturer selects the tractor to be tested and certifies that it is a stock model. Each tractor is equipped with the common power consuming accessories such as power steering, power lift pump, generator, etc., if available. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operating station. An official representative of …

Test 1311: Massey-Ferguson 2745 Diesel 8 And 24-Speed, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF THE TEST PROCEDURE

General

Tractors are tested at the University of Nebraska according to the Agricultural Tractor Test Code approved by the American Society of Agricultural Engineers and the Society of Automotive Engineers or official Nebraska test procedure.

The manufacturer selects the tractor to be tested and certifies that it is a stock model. Each tractor is equipped with the common power consuming accessories such as power steering, power lift pump, generator, etc., if available. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operating station. An official representative of …

Test 1316: International Hydro 84 Utility / Row Crop Diesel, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF THE TEST PROCEDURE

General

Tractors are tested at the University of Nebraska according to the Agricultural Tractor Test Code approved by the American Society of Agricultural Engineers and the Society of Automotive Engineers or official Nebraska test procedure.

The manufacturer selects the tractor to be tested and certifies that it is a stock model. Each tractor is equipped with the common power consuming accessories such as power steering, power lift pump, generator, etc., if available. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operating station. An official representative of …

Nebraska Summary 039: Case International 584, Case International 585, Case International 595 And Case International 3230, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Complete Elastic-Plastic Solution Around A Tensile Crack In Strain-Hardening Materials, Clancy Hatleberg

Mechanical Engineering ETDs

A complete elastic-plastic solution for both small and large scale yielding is found for the total stress field surrounding a tensile crack in an infinite sheet of strain-hardening materials under conditions of plane stress. The solution is based on the deformation theory of plasticity in conjunction with strain-hardening stress-strain relations, and is found by using the minimum of a modified complimentary energy principle coupled with a modified Ritz method. Numerical results are obtained for two approximate constitutive laws; a Ramberg-Osgood stress-strain relation and a modified Ramberg-Osgood stress-strain relation. Results indicate that the total stresses are discontinuous as the crack tip …

Test 1297: Case 2290 Powershift Diesel, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF THE TEST PROCEDURE General Tractors are tested at the University of Nebraska according to the Agricultural Tractor Test Code approved by the American Society of Agricultural Engineers and the Society of Automotive Engineers or official Nebraska test procedure. The manufacturer selects the tractor to be tested and certifies that it is a stock model. Each tractor is equipped with the common power consuming accessories such as power steering, power lift pump, generator, etc., if available. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operating station. An official representative of …

Test 1296: Case 2290 Manual Diesel 8-Speed, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF THE TEST PROCEDURE General Tractors are tested at the University of Nebraska according to the Agricultural Tractor Test Code approved by the American Society of Agricultural Engineers and the Society of Automotive Engineers or official Nebraska test procedure. The manufacturer selects the tractor to be tested and certifies that it is a stock model. Each tractor is equipped with the common power consuming accessories such as power steering, power lift pump, generator, etc., if available. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operating station. An official representative of …

Innovations In Heat Pumps, Ronald Hunter Howell, Harry J. Sauer Jr.

UMR-MEC Conference on Energy / UMR-DNR Conference on Energy

The status of the residential heat pump industry is reviewed. Some potential improvements in energy efficiency, operational reliability, and initial cost are described and delineated. These possible innovations include two-speed or variable speed compressors, reliable defrost initiation and termination, improved system components, modifications to the basic thermodynamic cycle, add-on-heat pumps, solar assisted heat pumps, annual cycle energy system, chemical heat pumps, and gas fired heat pumps.

Sizing Of Air-Conditioning Systems -- The New Methodology, Harry J. Sauer Jr., Ronald Hunter Howell

UMR-MEC Conference on Energy / UMR-DNR Conference on Energy

Accurate cooling load calculations for sizing air-conditioning equipment are more important today than ever. Properly sized equipment saves energy. This paper briefly describes a new method developed by ASHRAE for such calculations .

University Of Missouri--Rolla Wood Energy Research, Yildirim Omurtag, V. J. Flanigan, Nathan E. Welch

UMR-MEC Conference on Energy / UMR-DNR Conference on Energy

The overall objective of this project is to conduct a research and development program which will lead to the early commercialization of wood gasification technology to process wood residues typical of those found in the Ozark region.

The Design And Analysis Of A Unique Broadband Underwater Acoustic Source, Allan Mark Young

Retrospective Theses and Dissertations

Requirements exist for a unique type of underwater acoustic source. The transducer is in the form of a linear array of discrete elements and is required to have a constants transmitting voltage response and carefully controlled directivity characteristics over a two octave bandwidth. A generalized model of a linear array of cylindrical piezoelectric ceramic acoustic radiators is developed and applied to the design of a prototype which operates over approximately one half of the required bandwidth. The prototype transducer was built and the measured results are compared with those predicted by the model. Recommendations are made for improving the performance …

Interaction Between Structures And Fluids, Rahim Falsafi-Haghighi

Dissertations

A finite element model for the study of solid-fluid interaction, with applications in flow-induced vibration analysis of reactor vessel and heat exchanger internals, is presented. The model is based on the discretization of the solid equation of motion and the fluid continuity and momentum equations and employs the solid displacements together with the fluid pressure and velocity components as the nodal degrees of freedom. This permits a realistic and accurate implementation of boundary conditions, in contrast with methods using solid displacements and fluid pressure as the only field variables. The numerical solution of the resulting matrix equation, involving non-symetric matrices, …

Surface Roughness Effects In Hydrodynamic Lubrication, Johnny Lynn Teale

Mechanical Engineering ETDs

Prediction of pressure and leakage in a hydrodynamic bearing when surface roughness effects are important is an essential step in bearing design. The inclusion of surface roughness effects in bearing analysis allows more accurate prediction of bearing life. It has been shown that the average flow model developed by Cheng and Patir is a promising technique for determining surface roughness effects. The objective of this investigation is to examine the validity, applicability and limitation of the average flow model. Validity of the average flow model is ascertained by checking the independence of flow factors. Discussion of the general Reynolds equation …

Inviscid Two-Dimensional Vortex-Panel Method For Calculating The Pressure Distribution Over Noncircular Cylinders At Various Flow Incidence Angles, Sophia Kokkinos Ashley

Mechanical & Aerospace Engineering Theses & Dissertations

A method. has been implemented to calculate the potential flow pressure distribution over noncircular cylinders at various flow incidence angles. The inviscid, solution has been obtained by replacing the surface of a noncircular cylinder with a vortex sheet. The surface has been approximated by a number of flat panels. Each vortex panel has been assumed to have a constant vorticity, and the condition of no-circulation applied.. Solutions yield the local tangential velocity and pressure coefficient at each point.

The accuracy of the method has 'been established through comparison of the predicted results with existing exact theoretical results.

Comparisons of the …

Numerical Control Machining, Dennis L. Maclennan

Graduate Research Papers

Accurate and timely data depicting major aspects of manufacturing are essential to allow management to exercise effective controls for investments relating to automated equipment. One specific area of automated equipment can be termed "numerical control" (N/C) . "N/C is a technique for the control of production tools by information prerecorded in symbolic form (Devries, 1971, p. 1)." l This study is concerned with gathering material on the functional use and operation of N/C equipment. Specifically, the following areas of study were:

(1) to gather historical information on N/C equipment development;

(2) to investigate who are the major manufacturers of N/C …

Dynamics Of Submerged Cylindrical Shells With Eccentric Stiffening, Kerry Kier-Ten Chu

Dissertations

A theoretical analysis is presented for treating the free vibrations of submerged, ring stiffened cylindrical shells with simply supported ends. The effects of the eccentric stiffeners are averaged over the thin-walled isotropic cylindrical shell. The energy method is utilized and the frequency equation is derived by Hamilton's Principle. All three degrees of freedom are considered. Numerical results are presented for frequencies and mode separation for several cases of interest. Comparisons with previous theoretical and experimental results indicate good agreement. The cylindrical wave approximation and the plane wave approximation for the field equation were investigated. Their applicability was evaluated and the …

Deposition Of Suspensions In Laminar Flow In The Entrance Region Of Channels With Diffusive, Electrostatic And Gravitational Effects, Thomas Anthony Korjack

Dissertations

This investigation entailed the consideration of the deposition of suspensions in laminar flow in the entrance region of a parallel-plate channel, and both converging and diverging channels, under the combined influences of diffusive, electrostatic and gravitational effects. The fluid phase was assumed to be incompressible, steady and laminar; the particle phase was assumed to be steady, laminar, dilute, and with negligible lift force.

The complete solution of the problem involved solving the boundary layer equations for the completely viscous fluid phase, and the particulate momentum, continuity and potential equations for the particle phase. Since the resulting equations are non-linear partial …

Test 1276: White Field Boss 2-155 Dsl 18-Speed, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF THE TEST PROCEDURE General Tractors are tested at the University of Nebraska according to the Agricultural Tractor Test Code approved by the American Society of Agricultural Engineers and the Society of Automotive Engineers or official Nebraska test procedure. The manufacturer selects the tractor to be tested and certifies that it is a stock model. Each tractor is equipped with the common power consuming accessories such as power steering, power lift pump, generator, etc., if available. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operating station. An official representative of …

Test 1275: White Field Boss 2-135 Diesel 18-Speed, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF THE TEST PROCEDURE General Tractors are tested at the University of Nebraska according to the Agricultural Tractor Test Code approved by the American Society of Agricultural Engineers and the Society of Automotive Engineers or official Nebraska test procedure. The manufacturer selects the tractor to be tested and certifies that it is a stock model. Each tractor is equipped with the common power consuming accessories such as power steering, power lift pump, generator, etc., if available. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operating station. An official representative of …

Axisymmetric Air Jet Impinging On A Hemispherical Concave Plate, Stefan Jachna

Dissertations

This experimental study was conducted on an axisymmetric air jet impinging normally on a smooth, hemispherical, concave plate. The jet Reynolds numbers, based on bulk nozzle velocity and nozzle exit air properties, were between 14,000 and 75,000.

The impingement plate used in this work was a hemispherical surface with the radius of 94 mm.

Calibrated Pitot tubes and a micromanometer were used for pressure and velocity measurements. The Pitot tubes were mounted on precision positioning mechanisms permitting the accurate traversing of any direction in space. The test air flow rate was measured with calibrated rotometers.

The following results of this …

Test 1282: Steiger Tiger Iii St-450 And St-470 6-Speed (Diesel), Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF THE TEST PROCEDURE General Tractors are tested at the University of Nebraska according to the Agricultural Tractor Test Code approved by the American Society of Agricultural Engineers and the Society of Automotive Engineers or official Nebraska test procedure. The manufacturer selects the tractor to be tested and certifies that it is a stock model. Each tractor is equipped with the common power consuming accessories such as power steering, power lift pump, generator, etc., if available. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operating station. An official representative of …

Comparison Of Theoretical And Experimental Results Pertaining To R-Curves In Low And High Ductility Solids, Rabindra Nath Dash

Electronic Theses and Dissertations

Existing linear elastic fracture mechanics and J-integral analyses are well suited for safety assessments of high-strength, low-toughness materials. These analyses apply only to the onset of crack growth, which is usually tantamount to crack instability and structural failure in that class of materials. However, this is not the case for the low-strength, high-toughness materials in which crack instability may be preceeded [sic] by extensive stable crack growth under rising loads. Here, a substantial margin of safety may exist even when the onset of crack growth is imminent. This thesis describes research leading to a ductile fracture-mechanics methodology designed to treat …

David Brown Tractors: Inside Story, Nebraska Tractor Test Lab

Nebraska Tractor Tests

DAVID BROWN TRACTORS: INSIDE STORY

A summary of the design and manufacturing achievements of David Brown Tractors Ltd.

David Brown 'Firsts'

Few if any, tractor manufacturers can equal the David Brown record of pioneering achievement in tractor maufacture and development. Major examples are:

1937 - World's first farm tractor equipped with hydraulic lift and converging 3-point linkage

1948 - Two-speed power take-off, six-speed gearbox

1949 - High-speed direct injection diesel engine for farm tractors

1953 - Traction control (implement weight transfer)

1959 - All purpose tractor hydraulic system with single lever control.

1964 - Dial-controlled tractor hydraulic system

1968 - …

Test 1274: Steiger Panther Iii Pt-350 With Or Without Pto, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF THE TEST PROCEDURE

General

Tractors are tested at the University of Nebraska according to the Agricultural Tractor Test Code approved by the American Society of Agricultural Engineers and the Society of Automotive Engineers or official Nebraska test procedure.

The manufacturer selects the tractor to be tested and certifies that it is a stock model. Each tractor is equipped with the common power consuming accessories such as power steering, power lift pump, generator, etc., if available. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operating station. An official representative of …

Test 1278: Massey-Ferguson 2775 Diesel, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF THE TEST PROCEDURE

General

Tractors are tested at the University of Nebraska according to the Agricultural Tractor Test Code approved by the American Society of Agricultural Engineers and the Society of Automotive Engineers or official Nebraska test procedure.

The manufacturer selects the tractor to be tested and certifies that it is a stock model. Each tractor is equipped with the common power consuming accessories such as power steering, power lift pump, generator, etc., if available. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operating station. An official representative of …

Test 1281: John Deere 950 Diesel, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF THE TEST PROCEDURE General Tractors are tested at the University of Nebraska according to the Agricultural Tractor Test Code approved by the American Society of Agricultural Engineers and the Society of Automotive Engineers or official Nebraska test procedure. The manufacturer selects the tractor to be tested and certifies that it is a stock model. Each tractor is equipped with the common power consuming accessories such as power steering, power lift pump, generator, etc., if available. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operating station. An official representative of …

Test 1285: Kubota L185 Diesel, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF THE TEST PROCEDURE General Tractors are tested at the University of Nebraska according to the Agricultural Tractor Test Code approved by the American Society of Agricultural Engineers and the Society of Automotive Engineers or official Nebraska test procedure. The manufacturer selects the tractor to be tested and certifies that it is a stock model. Each tractor is equipped with the common power consuming accessories such as power steering, power lift pump, generator, etc., if available. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operating station. An official representative of …