Digital Commons Network^™

Test 1612: Case International 7140 And 7240 18-Speed, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF THE TEST PROCEDURE General Tractors are tested at the University of Nebraska according to the Agricultural Tractor Test Code approved by the American Society of Agricultural Engineers and the Society of Automotive Engineers or official Nebraska test procedure. The manufacturer selects the tractor to be tested and certifies that it is a stock model. Each tractor is equipped with the common power consuming accessories such as power steering, power lift pump, generator, etc., if available. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operating station. An official representative of …

Test 1610: Case International 7120 Diesel 18-Speed, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF THE TEST PROCEDURE General Tractors are tested at the University of Nebraska according to the Agricultural Tractor Test Code approved by the American Society of Agricultural Engineers and the Society of Automotive Engineers or official Nebraska test procedure. The manufacturer selects the tractor to be tested and certifies that it is a stock model. Each tractor is equipped with the common power consuming accessories such as power steering, power lift pump, generator, etc., if available. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operating station. An official representative of …

Test 1611: Case International 7130 And 7230 18-Speed, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF THE TEST PROCEDURE General Tractors are tested at the University of Nebraska according to the Agricultural Tractor Test Code approved by the American Society of Agricultural Engineers and the Society of Automotive Engineers or official Nebraska test procedure. The manufacturer selects the tractor to be tested and certifies that it is a stock model. Each tractor is equipped with the common power consuming accessories such as power steering, power lift pump, generator, etc., if available. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operating station. An official representative of …

Calculations Of Three-Dimensional Transonic Flows Using The Implicit Formulation Of The Isenthalpic Euler Equations With Flux Vector Splitting, Frank E. Cannizzaro

Mechanical & Aerospace Engineering Theses & Dissertations

A numerical method for solving three-dimensional transonic flows using the isenthalpic formulation of the Euler equations is developed. The method uses van Leer's flux vector splitting to solve the implicit formulation of the governing equations, which are applied to a cell centered finite-volume scheme. A three factor spatial approximate factorization is implemented in solving the implicit part of the governing equations. Time marching to a steady state solution requires short computational times due to the relative efficiency of the basic method. Computational times are further reduced by the implementation of the multigrid acceleration technique, which provided converged solutions in approximately …

Application Of Advanced Grid Generation Techniques For Flow Field Computations About Complex Configurations, Monchai Kathong

Mechanical & Aerospace Engineering Theses & Dissertations

In the computation of flow fields about complex configurations, it is very difficult to construct a boundary-fitted coordinate system. An alternative approach is to use several grids at once, each of which is generated independently. This procedure is called the "multiple grids" or "zonal grids" approach, and its applications are investigated in this study. The method is a conservative approach and provides conservation of fluxes at grid interfaces. The Euler equations are solved numerically on such grids for various configurations. The numerical scheme used is the finite-volume technique with a three-stage Runge-Kutta time integration. The code is vectorized and programmed …

Theoretical & Computational Investigation Of Algorithms For Simultaneous Heat & Moisture Transport In Buildings. Task 2 Final Report, Milestone #218 & 220 Combined. Iv (Copies 1ref, 2,3), Florida Solar Energy Center, Alp Kerestecioglu

FSEC Energy Research Center®

In keeping with the national energy policy goal of fostering an adequate supply of energy at a reasonable cost, the United States Department of Energy (DOE) supports a variety of programs to promote a balanced and mixed energy resource system. The mission of the DOE Solar Buildings Research and Development Program is to support this goal, by providing for the development of solar technology alternatives for the buildings sector. It is the goal of the Program to establish a proven technology base to allow industry to develop solar products and designs for buildings that are economically competitive and can contribute …

Whole-Building Moisture Experiments And Data Analysis. Draft Task 1 Final Report, Milestone #219. February 5, 1988. 91 P., Florida Solar Energy Center, Adel A. Kamel

FSEC Energy Research Center®

For four months (August -November) in 1987 whole -building moisture capacitance experiments were done on a townhouse in Cocoa, Florida. The experiments were designed to: 1. Observe the response of a building to imposed moisture flux 2. Determine the moisture storage capacity of the building and furnishings 3. Evaluate simple models designed to predict the response of room air humidity ration to pulses of moisture 4. Assess two innovative approaches to cooling (off-peak cooling and DESRAD) The results of the tests indicated that moisture storage in the furnishings is much greater than moisture storage in the air. The bare building …

Investigation Of The Characteristics Of The Kerf And The Surface Generated In The Course Of Cutting Titanium With Abrasive Waterjets, Ajay Vora

Theses

The effect of cutting parameters on the quality of cut in the course of cutting Titanium (Gr.2) with Abrasive Waterjet is investigated. The cutting parameters include nozzle traverse rate, size and feed rate of abrasives and nozzle(s) diameter. The width of kerf (top and bottom ), taper and roughness is studied. The measurements are tabulated and plots are made to study the trend and relationship for each set of parameters.

The qualitative conclusions are made successfully but no quantitative relationship was derived. Suggestions are made for the evaluation of technology for feasibility and economic justification, and to achieve desired cutting …

Integration Of Cad/Cam System Into A Waterjet Cutting Cell, Sanjay C. Shah

Theses

The work is intended to bridge the gap between CAD and CAM fora waterjet cutting cell. The output of CAD is used by CAM directly through the software interface developed. To achieve this, a postprocessor is designed for a two-dimensional system for the series 8200 Allen Bradley's 5-axes Robot Controller. Calma's DDM & DIMENSION III interactive graphics system implemented on VAX was used for the part design. The postprocessor is a computer program, written in the structured FORTRAN, that is unique for a given machine-tool/controller combination. The conversion of the coding and recording format of the APT file to the …

Investigation Of A Technology For Glass Shaping By The Use Of Abrasive Waterjet, Wu-Tzung Lee

Theses

This study investigates the effects of AWJ properties on the results of glass machining and examines the feasibility of contour glass cutting. The principal defects of AWJ glass cutting are identified. A practical technique to prevent defects and to improve the quality of the glass surface is presented. A computer package was developed to provide a computer-aided programming function, a control program transformation fuction, and a object image operation function. Throughout the programming function, robot control programs can be generated to improve cutting quality and cutting speed. The transformation function can be used to change the programming modes or the …

Seizure And Wear Testing Methodology, I-Tsung Shih

Theses

In this work the seizure as an adhesive wear has been discussed and analyzed The diffusion hypotheses is accepted as the seizure mechanism. It was determined that the surface of machine components, material properties, and contact stresses in sliding and loading zone are responsible for the wear.

A computer controlled wear testing methodology has been developed and a wear testing machine has been designed and assembled. The tests for the selected gray cast non and alloy steel specimens with different surface treatment were performed on the designed wear testing machine.

The test results showed that the selected materials with additional …

Comparison Of Various Techniques For The Detection Of Lines In 2-Dimensional Images, Somayajulu Bhamidipati

Theses

The detection of straight lines in 2-dimensional images leading to polygonal approximation to the boundaries of the objects is one of the important stages in scene analysis as it leads to the description of the images. The comparison of three diverse approaches for this problem in terms of the efficiency and accuracy is made, and their performance for different types of data and different sets of parameters is studied in this thesis.

The data points are generated using either an edge detection algorithm using chain encoding on real images or a synthetic data generator, which can create a variety of …

Two Domain Heat Transfer Studies Using A Coupled Finite-Difference And Boundary Element Programs, Serap Dikmenli

Theses

An iterative coupling of a finite-difference boundary layer code "STAN5"' and a boundary element code "BEASY"2 have been used to study two dimensional convective-conductive problems. The coupling method essentially leaves undisturbed the codes of these programs and uses their custom features in their applicable domains. The boundary layer program is used-in the convective domain, while "BEASY" is used in the solid domain. Compatability conditions are established between these domain solutions and an iterative scheme is used until these conditions are mutually satisfied.

The indirect communication of compatability (boundary) criteria between these programs was achieved by two editor/data-transferor like programs. Combined …

Computer Aided Synthesis Of A Four-Bar Linkage To Generate A Symmetrical Coupler Curve, Shailendra R. Pachalag

Theses

The purpose of this study is to develop a new analytical technique for the synthesis of four-bar mechanisms to generate symmetrical curves with a coupler point passing through 8 points. The geometric expressions involved in kinematic synthesis often tend to offer difficulties such as negative radicals, alternative choices and repetitions. Here a solution procedure has been developed which avoids these difficulties. This solution procedure includes a development of a computer algorithm that should synthesize a crank-rocker type linkage for any given input crank length. This algorithm dismisses all solutions involving negative radicals and lists magnitudes of members so that those …

Test 1607: White 160 Diesel And White Workhorse 170 Diesel 18-Speed, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF THE TEST PROCEDURE General Tractors are tested at the University of Nebraska according to the Agricultural Tractor Test Code approved by the American Society of Agricultural Engineers and the Society of Automotive Engineers or official Nebraska test procedure. The manufacturer selects the tractor to be tested and certifies that it is a stock model. Each tractor is equipped with the common power consuming accessories such as power steering, power lift pump, generator, etc., if available. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operating station. An official representative of …

Test 1608: Field Boss 185 Diesel, White 185 Diesel And White Workhorse 195 Diesel 18-Speeds, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF THE TEST PROCEDURE General Tractors are tested at the University of Nebraska according to the Agricultural Tractor Test Code approved by the American Society of Agricultural Engineers and the Society of Automotive Engineers or official Nebraska test procedure. The manufacturer selects the tractor to be tested and certifies that it is a stock model. Each tractor is equipped with the common power consuming accessories such as power steering, power lift pump, generator, etc., if available. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operating station. An official representative of …

A Feasible Direction Procedure For General Multiple Objective Optimization, Wen-Tsia Liu

Dissertations

The Feasible Direction Finding Problem (DFP) of Zoutendijk is adapted to create a general Mathematical Programming (MP) algorithm for treating optimization problems with multiple objective functions. Classically such problems are reduced to standard MP form by converting them to single objective function problems by the use of weighting functions. Unfortunately not all practical problems can be so reduced. Consider the problem of maximizing the strength of a structure. Typically there are several, or even many, failure modes. All active failure modes must be included in the optimal search in such a way that resistance to one active mode can not …

The Effect Of Elastic Boundary Conditions On The Dynamic Response Of Rectangular Plates, Terry K. Brewer

Mechanical & Aerospace Engineering Theses & Dissertations

Natural frequencies and forced steady-state harmonic response for the vibration of uniform rectangular plates with edges elastically restrained against rotation and transverse translation are addressed. A single mode Rayleigh-Ritz solution is derived using functions that describe the normal modes of vibration of a beam whose ends are elastically restrained. The finite element solution is obtained for comparison. MACSYMA symbolic manipulation system is implemented as an aid to the mathematical rigor of the Ritz approach and NASTRAN finite element code is used to model the mechanical system. Comparisons are made to published results and the solutions of this study are found …

Integral Equation Solution Of The Full Potential Equation For Three-Dimensional, Steady, Transonic Wing Flows, Li-Chuan Chu

Mechanical & Aerospace Engineering Theses & Dissertations

An integral equation method for solving the full potential equation has been developed for three dimensional transonic vortex-wing flows. This method is capable of capturing shocks using the Murman-Cole type of finite difference scheme and is capable of predicting accurate and force-free wake shape as well.

Reading the full potential equation as Poisson's equation, the solution for the velocity field has been expressed in terms of an integral equation using Green's theorem. The solution consists of a surface integral of vorticity distribution on the wing and its free-vortex sheets and a volume integral of source distribution within a computational region …

Stability Of Steady Cross-Waves: Theory And Experiment, Seth Lichter, Andrew J. Bernoff

All HMC Faculty Publications and Research

A bifurcation analysis is performed in the neighborhood of neutral stability for cross waves as a function of forcing, detuning, and viscous damping. A transition is seen from a subcritical to a supercritical bifurcation at a critical value of the detuning. The predicted hysteretic behavior is observed experimentally. A similarity scaling in the inviscid limit is also predicted. The experimentally observed bifurcation curves agree with this scaling.

Closed Loop Machining In Precise Turning, Ching-Song Wei

Theses

Closed loop machining (CLM) is one of the most reliable ways to automate tool setting, part positioning and measurement on CNC machine tool. It not only can assure the quality of the product but also can improve the productivity of the machine. This paper describes the CLM from basic turning concept to application of CLM, including the feature of Mark Century 2000T and the programming methods in precise turning.

The hardware and software requirements for CLM system were presented. The algorithm for CLM programs was developed completely with a series of flow charts. Then, on the base of two projects, …

Engraving By Cnc Milling Machine, Ram Tatiparti Reddy

Theses

A detailed study of NC, CNC and Engraving is presented. Engraving of letters of different sizes is done using the present technology in a CNC milling machine. This thesis also contains the design of a communication interface between Mark Century One Plus controller and different peripherals. Software for Engraving and Communication between the controller and a PC is developed. The generated NC code from software is simulated on the controller and the product is cut.

Development Of A Low Cost Pc Based Robot Vision System, Raghunandan Jadhav

Theses

There has been a continued. interest in utilizing machine vision systems for robot guidance applications. Commercial vision systems can be programmed to give information about the parts in the robot work area and this information can be used by the robot computer to guide the robot. In most applications, however, the vision information cannot be easily integrated with the robot control language. This thesis considers implementation of part identification routines directly into a robot guidance language. This makes all the complicated machine vision algorithms transparent to the user and allows him to treat higher level vision functions as an extension …

Characteristics And Optimal Design Of Variable Airgap Linear Force Motors, Ming-Chuan Leu, E. V. Scorza, D. L. Bartel

Mechanical and Aerospace Engineering Faculty Research & Creative Works

An analytical model for predicting the characteristics of variable airgap linear force motors is developed. the model takes into account magnetic losses including the leakage and fringing effects and the reluctance existing at the contacts between permanent magnets and pole pieces. the model is validated by comparing its predicted characteristics with the results obtained from experiments and a finite element program. with the use of the modelled characteristics, computer programs based on the method of constrained steepest descent with state equations are developed for automating and optimising the design of linear force motors. Numerical studies are made for both minimisation …

Nebraska Summary: S048 John Deere 2155, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Nebraska Summary: S031 Massey Ferguson 375, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

An Experimental Cost Model For The Analysis Of Quality Cost In A Manufacturing Enterprise, Wallace Charles Carlson Jr.

Dissertations and Theses @ UNI

The intent of the study was to construct a quality cost model for manufacturing enterprises. A quality cost model provides a manufacturing enterprise with a cost structure which enables it to gauge and measure the efficiency and effectiveness of its management and processes. The quality cost model was specifically constructed to aid a manufacturing enterprise in establishing a quality cost system for its operations and activities and contains three distinct initial implementation or decision areas; the quality cost management decisions area, the quality cost system applications area, and the quality cost system utilization area.

The quality cost model was evaluated …

Condensation Method For Humidity Measurement In The Umr Cloud Simulation Chamber., Donald E. Hagen, Daniel R. White, Darryl J. Alofs

Mechanical and Aerospace Engineering Faculty Research & Creative Works

A Cloud Simulation Facility Has Been Developed for the Study of Various Atmospheric Cloud Processes. the Initial Relative Humidity of the Air Sample Put into the Cloud Chamber is a Key Parameter in Virtually Any Experiment and Needs to Be Known Accurately. This Report Describes How the Cloud Simulation Chamber itself Has Been Used as a Condensation Type Hygrometer to Calibrate the System's Humidifier. Two Distinct and Physically Different Methods for Inferring Mixing Ratio Are Used, One Exploiting the Sensitivity of Aerosol Activation to Humidity, and the Other Exploiting the Sensitivity of the Rate of Growth of Cloud Droplets to …

Theoretical Thermodynamic Properties Of Low Temperature Fluids, Zul Azhar Zahid Jamal

Masters Theses

The thermodynamic functions for low temperature fluids are computed using parametric integral equations and perturbation theory. Parametric integral equation N is applied to a low temperature Lennard-Jones gas. It is found that there is no significant improvement over the better known parametric integral equation C. The two parameter integral equation T is applied to a low temperature square-well potential and is found to be unsatisfactory at reduced temperatures of T*= 1.4 and 1.6, but quite accurate at T* = 2.2. The equation T results for T* = 2.2 are used as the reference system in perturbation theory computations. Tables of …

University Of Missouri-Rolla Cloud Simulation Facility: Proto Ii Chamber, Daniel R. White, James L. Kassner, John C. Carstens, Donald E. Hagen, John L. Schmitt, Darryl J. Alofs, Alfred R. Hopkins, Max B. Trueblood, Max W. Alcorn, William L. Walker

Mechanical and Aerospace Engineering Faculty Research & Creative Works

The Graduate Center for Cloud Physics Research at UMR Has Developed a Cloud Simulation Facility to Study Phenomena Occurring in Terrestrial Clouds and Fogs. the Facility Consists of a Pair of Precision Cooled-Wall Expansion Chambers Along with Extensive Supporting Equipment. the Smaller of These Chambers, Described in This Article, is Fully Operational, and is Capable of Simulating a Broad Range of In-Cloud Thermodynamic Conditions. It is Currently Being Used to Study Water Drop Growth and Evaporation for Drops Nucleated (Activated) on Well-Characterized Aerosol Particles. Measurements Have Been Made Not Only for Continuous Expansions (Simulated Updraft) But Also for Cyclic Conditions, …