Digital Commons Network^™

Nebraska Summary: S217 White 6045, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Nebraska Summary: S285 Valmet 8150, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Plastic Fiber Rolling For Concrete Reinforcement, Jeffery S. Thomas

Masters Theses

"Fiber reinforced concrete is gaining in acceptance and usage as its strength and toughness benefits are realized. Polypropylene fibers are currently the most commonly used fibers. However, the cost of virgin plastics limits the percent content that can be economically added to concrete. One would first believe that recycled plastics could offer a viable alternative to virgin-plastic fibers, but at present time extra selection and cleaning steps required to reprocess the recycled plastic into fibers makes it more expensive than virgin-plastic fibers. A fiber rolling process conceived and developed at the University of Missouri-Rolla has the potential of making recycled …

The Modeling Of Structural-Acoustic Interaction Using Coupled Fe/Be Method And Control Of Interior Acoustic Pressure Using Piezoelectric Actuators, Yucheng Shi

Mechanical & Aerospace Engineering Theses & Dissertations

A coupled finite element (FE) and boundary element (BE) approach is presented to model full coupled structural/acoustic/piezoelectric systems. The dual reciprocity boundary element method is used so that the natural frequencies and mode shapes of the coupled system can be obtained, and to extend this approach to time dependent problems. The boundary element method is applied to interior acoustic domains, and the results are very accurate when compared with limited exact solutions. Structural--acoustic problems are then analyzed with the coupled finite element/boundary element method, where the finite element method models the structural domain and the boundary element method models the …

Application Of Reanalysis Techniques For Pattern Design Of Spot Welds, Young San Kim

Mechanical & Aerospace Engineering Theses & Dissertations

Extensive benchmarking on competitive cars has shown that the durability of vehicles, assembly-induced variations, and assembly cost are directly related to the quality and number of spot welds. On most luxury cars, approximately 4,500 to 5,000 spot welds are found. On less expensive cars, the range is from 3,500 to 4,500. These cars usually inherit more noise, rattles, squeaks, and other quality-related problems. These problems have motivated the search for a new capability to systematically place welds in the most critical areas, with a minimum number of welds for car bodies, while satisfying all performance requirements (e.g., stiffness, stress distribution, …

Numerical Simulation Of Complex, Three-Dimensional, Turbulent-Free Jets, Robert V. Wilson

Mechanical & Aerospace Engineering Theses & Dissertations

Three-dimensional, incompressible turbulent jets with rectangular and elliptical cross-section are simulated with a finite-difference numerical method. The full Navier-Stokes equations are solved at low Reynoids numbers, whereas at high Reynolds numbers filtered forms of the equations are solved along with a sub-grid scale model to approximate the effects of the unresolved scales. A 2-N storage, third-order Runge-Kutta scheme is used for temporal discretization and a fourth-order compact scheme is used for spatial discretization. Although such methods are widely used in the simulation of compressible flows, the lack of an evolution equation for pressure or density presents particular difficulty in incompressible …

Methodology Evaluation For Remotely Estimating Water Quality Parameters In Estuarine Waters, Charles R. Bostater, Manuel Gimond

Ocean Engineering and Marine Sciences Faculty Publications

Water absorption signatures were measured from water samples placed in a 50 cm pathlength cylindrical cuvette. Quantitative analysis of chlorophyll-a and dissolved organic matter (DOM- humic acid, fulvic acid, or tannic acid) was conducted using second derivative spectra followed by computation of double inflection ratio (DIR) spectra for all possible combinations of bands (from 362-1 1 15 nm with 252 channels). A specially designed instrument system is described which allows measurements of absorption of particulate and dissolved organic matter (chlorophyll-a and DOM) in a water sample. The ability of the system to allow measurement of absorption signatures and relating the …

Dynamic Pulse Buckling Of Columns With Viscous Damping, Murli Kadandale

Masters Theses

This is a study of dynamic pulse buckling of columns with viscous damping. The differential equations of motion were obtained using the Bemoulli-Navier hypothesis. The effects of axial and rotary inertia were included in the analysis. The Voigt-Kelvin model for a viscoelastic material is used. The Finite Difference Method was employed to solve the differential equations of motion. First columns without geometrical imperfections were studied, and a correlation between the damping modulus and the more familiar damping ratio was obtained. Then beams with initial geometrical imperfection were studied. A suitable dynamic buckling criterion was defined. It was observed that viscous …

The Effect Of Rotor Wake/Exit Guide Vane Interaction On The Total Pressure Losses In An Airfoil Cascade, Aaron Mosebach

Masters Theses

Computational simulations have been performed to study the effects of unsteady rotor wakes on the total pressure losses and the boundary layer characteristics in a compressor cascade. In the numerical simulations, transitional and turbulent flow conditions were modeled at design and off-design inlet flow angles, and for varying rotor wake widths and wake velocity deficits.

First, simulations were performed in the absence of rotor wakes at the inlet of the EGV (Exit Guide Vane) cascade. Second, simulations were performed for different wake width and wake velocity deficit values at the inlet of the EGV cascade. The majority of the numerical …

Design, Fabrication And Characterization Of Micro Opto-Electro-Mechanical Systems, Darren E. Sene

Theses and Dissertations

Several micro-opto-electro-mechanical structures were designed using the Multi-User MEMS Process (MUMPS). Specific design techniques were investigated for improving the capabilities of elevating flip up structures. The integration of several flip up microoptical structures into a microoptical system was explored with emphasis on the development of a microinterferometer. The thermal effects on the Modulus of Elasticity were determined by detecting the resonant frequency for a square Flexure Beam Micromirror Device. The resonance of the device was found to match theory to within 0.1 % and the Modulus of Elasticity was found to decrease by 0.041 GPa/K from 290 to 450 K. …

A Psychological Perspective On Service Segmentation Models: The Significance Of Accounting For Consumers' Perceptions Of Waiting And Service, Ziv Carmon, J. George Shanthikumar, Tali F. Carmon

Industrial and Manufacturing Engineering

We examine how service should be divided and scheduled when it can be provided in multiple separate segments. We analyze variants of this problem using a model with a conventional function describing the waiting cost, that is modified to account for some aspects of the psychological cost of waiting in line. We show that consideration of the psychological cost can result in prescriptions that are inconsistent with the common wisdom of queuing theorists derived according to the conventional approach (e.g., equal load assignments). More generally, our intention in this paper is to illustrate that aspects of the psychological cost of …

Vibration As An Aid In Robotic Peg-In-Hole Assembly, Hsin-Te Liao

Dissertations

This dissertation presents an analytical and experimental investigation of vibration assisted engagement for parts mating. A dynamic model of assembly is established by using Lagrange's equation for impact to derive impact equations for a robotic manipulator in peg-in-hole assembly. The model can be used to analyze part motion and contact force in the mating of parts by robots. The impact equations of a SCARA robot are derived using this model and utilized to investigate how robot configuration, insertion speed, chamfer angle, coefficient of restitution and other system parameters affect impulsive force and departure angle in the assembly of a peg …

Particle Deposition On Surfaces In A Divergent Channal Flow, Ding Sun

Dissertations

Particle trajectory and deposition of two phase gas-solid flows in a convergent or divergent two-dimensional channel are investigated numerically in a wide range of parameters. For the fluid phase, a two dimensional, incompressible laminar fluid flow is considered in the analysis. The particle phase is a diluted suspension. The effects of inertia, gravity, viscous force and electrostatic image force are included in the computational model.

Both convergent and divergent channel flow are solved by the finite element method based on the software FIDAP. The flow separations will appear in a divergent channel and their separation positions are obtained in the …

Performance Analysis For Genetic Algorithms., Hermrean Wong

Dissertations

Genetic algorithms have been shown effective for solving complex optimization problems such as job scheduling, machine learning, pattern recognition, and assembly planning. Due to the random process involved in genetic algorithms, the analysis of performance characteristics of genetic algorithms is a challenging research topic. Studied in this dissertation are methods to analyze convergence of genetic algorithms and to investigate whether modifications made to genetic algorithms, such as varying the operator rates during the iterative process, improve their performance. Both statistical analysis, which is used for investigation of different modifications to the genetic algorithm, and probability analysis, which is used to …

Analysis Of Cim Performance Using Different Lan Structures A Simulation Approach, Kirk Rawle

Theses

This research illustrates a systematic procedure for modeling and performance analysis of the integration effect of communication network to the physical system. The concept is to model different layouts of Computer Integration Manufacturing (CIM) using different Local Area Network(LAN) structures. The steps to accomplish this concepts are, a) To determine the performance measures for physical layouts and the communication network, in order to obtain a performance analysis. b) Modeling the physical layout using Promodel simulation package. c) Extracting results from the outcome of the simulation of the physical layout and using this as input to the communication network simulation. d) …

Chute Flow Experiments, Yahong Zhang

Theses

The objective of this thesis is to study the behavior of granular materials flowing down an inclined chute using three diagnostic techniques under different chute inclination angles and chute floor conditions. The three methods are: (1) tracking the motion of single particle within the mass in a noninvasive manner using a transmitting sphere and antenna receiving system, (2) scale mass flow rate measurement, and (3) high speed camera system to obtain flow velocity measurements.

For these purposes, an experimental setup has been completed and a set experiments has been performed.

An Experimental Investigation Of Wall Cooling Effects On Hypersonic Boundary Layer Stability In A Quiet Wind Tunnel, Alan E. Blanchard

Mechanical & Aerospace Engineering Theses & Dissertations

One of the primary reasons for developing quiet tunnels is for the investigation of high-speed boundary-layer stability and transition phenomena without the transition-promoting effects of acoustic radiation from tunnel walls. In this experiment, a flared-cone model under adiabatic- and cooled-wall conditions was placed in a calibrated, 'quiet' Mach 6 flow and the stability of the boundary layer was investigated using a prototype constant-voltage anemometer. The results were compared with linear-stability theory predictions and good agreement was found in the prediction of second-mode frequencies and growth. In addition, the same 'N=10' criterion used to predict boundary-layer transition in subsonic, transonic, and …

Experimental Investigation Of The Inlet Deflector Configuration Variation In The Flow Field At Mach 1.9, Kyu C. Hwang

Mechanical & Aerospace Engineering Theses & Dissertations

In recent years, active research has been conducted to study the technological feasibility of supersonic laminar flow control on the wing of the High Speed Civil Transport (HSCT). For this study, the F-16XL has been chosen due to its highly swept crank wing planform that closely resembles the HSCT configurations. During flights, it is discovered that the shock wave generated from the aircraft inlet introduces disturbances on the wing where the data acquisition is conducted. The flow field about a supersonic inlet is characterized by a complex three-dimensional pattern of shock waves generated by the geometrical configuration of a deflector …

Buckling Analysis And Optimum Design Of Multidirectionally Stiffened Composite Curved Panel, Navin R. R. Jaunky

Mechanical & Aerospace Engineering Theses & Dissertations

Continuous filament grid-stiffened structure is a stiffening concept that combines structural efficiency and damage tolerance. However, buckle resistant design optimization of such structures using a finite element method is expensive and time consuming due to the number of design parameters that can be varied. An analytical optimization procedure which is simple, efficient and supports the preliminary design of grid-stiffened structures for application to combined loading cases is needed.

An analytical model for a general grid-stiffened curved panel is developed using an improved smeared theory with a first-order, shear-deformation theory to account for transverse shear flexibilities and local skin-stiffener interaction effects. …

Chp And Energy Conservation, Jim Mcgovern

Articles

The principles of the use of 'combined heat and power' (CHP) for the achievement of fuel energy conservation, minimisation of environmental impact and economic advantage are explained. A distinction is made between the two types of outputs: heat and work. It is argued that an efficiency value that is defined as the sum of the heat and work outputs divided by the energy of the fuel used is not very meaningful. An alternative, rational, efficiency is explained. It is concluded that CHP is an option to be considered where both heating and power are required, but is not a general …

A Theoretical Nonlinear Dynamical Model Of Coupled Heat And Momentum Transfer In Forced Convection Film Boiling, Jolie Ann Long

All Theses

In film boiling, a layer of vapor completely blankets the heated surface and prevents liquid contact with the surface. Film boiling is usually considered undesirable because it is an inefficient mode of heat transfer and can lead to temperatures in excess of those allowed for many materials. Because film boiling may inhibit desired heat transfer in several processes including metals manufacturing, cryogenic engineering, and electronic cooling, it is useful to consider how the film boiling vapor layer may be destabilized or altered such that time-averaged heat transfer is improved.

Window-On-Europe, S. R. Leclair, A. G. Jackson

Mechanical and Materials Engineering Faculty Publications

This report covers a three week visit to the following locations: 1.) A.A. Baikov Institute of Metallurgy of the Russian Academy of Science, Moscow, Russia; 2.) Institute for Applied Informatics, of the Ukrainian Academy of Science, Kiev, Ukraine; 3.)Engineering Design Center.Cambridge University, Cambridge, England- and 4) Artificial Intelligence Department, University of Edinburgh, Edinburgh, Scotland. The visits involved sites whose current research involved either empirical methods for the design of materials and resultant products and/or the development of empirical methods of potential benefit in automating empirical research of materials and/or processing. The report address, for each site, 1) a brief overview …

Studies Of Mixing Processes In Gases And Effects On Combustion And Stability, Frank Paul Kozusko Jr.

Mathematics & Statistics Theses & Dissertations

Three physical models of laminar mixing of initially separated gases are studied. Two models study the effects of the mixing dynamics on the chemical reactions between the gases. The third model studies the structure and stability of a laminar mixing layer in a binary gas. The three models are:

1. Two ideal and incompressible gases representing fuel and oxidizer are initially at rest and separated across an infinite linear interface in a two dimensional system. Combustion, expected as the gases mix, will lead to a rapid rise in temperature in a localized area, i.e. ignition. The mixing of the gases …

Reduced Small Engine Emissions With Perforated Plates, Derek S. Lindsay

Honors Capstone Projects and Theses

No abstract provided.

Closed-Loop Identification Of Unstable Systems In Time And Frequency Domains, Hyun Chang Lee

Mechanical & Aerospace Engineering Theses & Dissertations

This dissertation presents closed-loop identification algorithms of an unstable system in the time and frequency domains. In the time domain, the projection filter, which is a linear transformation which projects (transforms) a finite number of input-output data of a system into its current space, is used to relate the state-space model with a finite difference model. The method developed can take into account the effects of process noise as well as measurement noise and identify open-loop systems with unknown feedback dynamics in the closed-loop operation. Then the recursive relations between Markov parameters and the ARX model are derived to identify …

Open-Loop State-Space Model Identification From Closed-Loop Data, Lori Guy

Mechanical & Aerospace Engineering Theses & Dissertations

This thesis provides an investigation of a system identification algorithm which identifies an open-loop state-space model from a linear system that is operating under closed-loop conditions. In order to investigate the system identification algorithm some basic ideas of system identification theory are reviewed. Examples using simulated data are presented to characterize the effects of varying the parameters for open-loop and closed-loop system identification processes. Both noise· free and noise contaminated cases are simulated. Linear Quadratic Gaussian (LQG) control theory is reviewed and the motivation for using iterative LQG control feedback is discussed. The derivation of the proposed system identification algorithm …

Component Mode Synthesis-Based Design Methodology For Structural Modification And Synthesis, Venkateshwarlu Maroju

Mechanical & Aerospace Engineering Theses & Dissertations

In this work, structural modification and synthesis techniques based on component mode synthesis are presented. The component mode synthesis method formulates the eigenvalue equation of an entire structure in terms of the vibration characteristics of individual components in the assembly. Through this functional relationship, the individual components are successfully treated as the design entities in the proposed methodology. Unlike conventional design modification techniques that can only treat the properties of the finite elements as the design variables, this technique uses the vibration and static responses of the individual components as the design entities. The sensitivity derivatives of the global responses …

Extension To The Dynamic Modeling Of The Large Angle Magnetic Suspension Test Fixture, Lucas E. Foster

Mechanical & Aerospace Engineering Theses & Dissertations

The Large Angle Magnetic Suspension Test Fixture (LAMSTF) is a laboratory scale proof-of-concept system. The configuration is unique in that the electromagnets are mounted in a circular planar array. A mathematical model of the system had previously been developed, but was shown to have inaccuracies. These inaccuracies showed up in the step responses. Eddy currents were found to be the major cause of the modeling errors. In the original system, eddy currents existed in the aluminum baseplate, iron cores, and the sensor support frame. An attempt to include the eddy current dynamics in the system model is presented. The dynamics …

Modeling And Simulation Of Load Introduction For Fuselage Crown Panel Testing, Kevin P. Belack

Mechanical & Aerospace Engineering Theses & Dissertations

This paper discusses the mechanism and behavior of load introduction to internally pressurized fuselage crown panels. Emphasis is placed on the finite element modeling of a simulated pressure-box test machine and representative fuselage crown panel. The geometry and mesh requirements for the finite element model are examined through numerical studies which gradually increase in complexity. These numerical studies culminate in the detailed specification of boundary conditions, mesh densities, load introduction mechanisms, element choice and solution process for the simulation of a pressure-box test machine and test panel.

The results obtained using the finite element model are then compared with experimental …

Non-Linear Boundary-Layer Receptivity Due To Distributed Surface Roughness, Tahani R. Amer

Mechanical & Aerospace Engineering Theses & Dissertations

The process by which a laminar boundary layer internalizes the external disturbances in the form of instability waves is known as boundary-layer receptivity. The objective of the present research was to determine the effect of acoustic excitation on boundary-layer receptivity for a flat plate with distributed variable-amplitude surface roughness through measurements with a hot-wire probe. Tollmien-Schlichting mode shapes due to surface roughness receptivity have also been determined, analyzed, and shown to be in agreement with theory and other experimental work. It has been shown that there is a linear relationship between the surface roughness and receptivity for certain roughness configurations …