Digital Commons Network^™

Nebraska Summary: S257 Case-Ih Mx 110, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Nebraska Summary: S254 Caterpillar Challenger 55, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Nebraska Summary: S303 Massey Ferguson 6270, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Numerical Simulations Of Full- Scale Corroded Pipe Tests With Combined Loading, Samit Roy, S. Grigory, M. Smith, M. F. Kanninen, M. Anderson

Mechanical and Aerospace Engineering Faculty Research & Creative Works

The ANSI/ASME B31G guideline has been useful to pipeline operators in assessing the integrity of corroded line pipe. Because large safety margins have had to be incorporated, the guidelines can be excessively conservative, which in turn can force costly repairs and replacements that may not actually be necessary. On the other hand, because the current guidelines consider only pressure loading and neglect bending and axial compression, they could give nonconservative failure predictions when combined loading exists. Therefore, a study was initiated to develop a theoretically sound methodology for assessing the integrity of corroded line pipe subjected to combined loading. A …

Integrating Design Into The Sophomore And Junior Level Mechanics Courses, Douglas R. Carroll

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Engineering schools across the country are developing ways of integrating design into their curriculum, and a question that often arises is how to best integrate design into the sophomore and junior level courses. Freshman design projects or mechanical dissection courses are designed to give the students hands-on experience in conceptual design and construction, with little if any of the mathematical modeling normally used in engineering design. The capstone senior design project is a true engineering design experience, where students draw from their background to conceptualize, analyze, model, refine, and optimize a product to meet design, manufacturing, and life cycle cost …

A System For Collecting Milligram Quantities Of Cloud Condensation Nuclei, Darryl J. Alofs, Donald E. Hagen, Steven D. Medley, Daniel R. White, John L. Schmitt, Allen L. Williams

Mechanical and Aerospace Engineering Faculty Research & Creative Works

An Experimental System to Collect Cloud Condensation Nuclei (CCN) Onto Filters in Amounts Sufficient for Chemical Analysis is Described. This Experimental Apparatus is Designed to Process Ambient Air at a Rate of More Than 1 M3/min. Two Identical Systems Have Been Built. One is Installed in a Laboratory at Rolla, MO. the Other is Installed on an 11 M Long Trailer. the System Isolates Three Size Classes of CCN, Having Mass Median Diameters of 0.27, 0.12, and 0.075 Μm, Respectively, and Mass Collection Rates of 11.5, 1.28, and 0.13 Mg/day, Respectively. the above Sizes and Collection Rates Are Obtained from …

Modeling And Simulation Of Optical Characteristics Of Microelectromechanical Mirror Arrays, Peter C. Roberts

Theses and Dissertations

MEMS (Micro-Electro-Mechanical Systems) micromirror devices can be used to control the phase of a propagating light wavefront, and in particular to correct aberrations that may be present in the wavefront, due to either atmospheric turbulence or any other type of fixed or time and space varying aberrations. In order to shorten the design cycle of MEMS micromirror devices, computer software is developed to create, from MEMS micromirror device design data, a numerical model of the MEMS device. The model is then used to compute the far field diffraction pattern of a wavefront reflected from the device, and to predict the …

Microelectromechanical Isolation Of Acoustic Wave Resonators, James R. Reid Jr.

Theses and Dissertations

Microelectromechainical systems (MEMS) is a rapidly expanding field of research into the design and fabrication of actuated mechanical systems on the order of a few micrometers to a few millimeters. MEMS potentially offers new methods to solve a variety of engineering problems. A large variety of MEMS systems including flip-up platforms, scanning micromirrors, and rotating micromirrors are developed to demonstrate the types of MEMS that can be fabricated. The potential of MEMS for reducing the vibration sensitivity of surface acoustic wave and surface transverse wave resonators is then evaluated. A micromachined vibration isolation system is designed and modeled. A fabrication …

Demonstrating Optical Aberration Correction With A Mems Micro-Mirror Device, Shaun R. Hick

Theses and Dissertations

This research conducted the first demonstrated use of a micro-electro-mechanical structure (MEMS) mirror array to correct a static optical aberration. A well-developed technique in adaptive optics imaging systems uses a deformable mirror to reflect the incident wave front to the imaging stage of the system. By matching the surface of the deformable mirror to the shape of the wave front phase distortion, the reflected wave front will be less aberrated before it is imaged. Typical adaptive optics systems use piezo-electric actuated deformable mirrors. This research used an electrostatically actuated, segmented mirror array, constructed by standard MEMS fabrication techniques, to investigate …

Artificial Cochlea Design Using Micro-Electro-Mechanical Systems, George C. Dalton Ii

Theses and Dissertations

The use of Micro-Electro-Mechanical Systems (MEMS) in the design of an artificial cochlea is investigated in depth. Interdigitated finger (comb), cantilever, bridge, and mirror resonators are presented as possible devices used to implement the artificial cochlea. These resonators are demonstrated to be extremely high Q devices, capable of being tuned with a simple DC bias. This suggests a possible change to existing cochlea models that claim highly complex AC feedback as being responsible for changes in the damping of the basilar membrane. The new cochlea model presented here, using MEMS to approximate the tuning of the basilar membrane, may be …

Diffuse Energy Propagation On Heterogeneous Plates: Structural Acoustics Radiative Transfer Theory, Joseph A. Turner, Richard L. Weaver

Department of Engineering Mechanics: Faculty Publications

The propagation of diffuse energy on an unwetted flat plate with attached heterogeneities is examined using a statistical, multiple scattering approach. The statistically homogeneous heterogeneities lightly couple the membrane and flexural waves. The problem is formulated in terms of the Bethe–Salpeter equation, which governs the field covariance. It is reduced to a radiative transfer equation in the limit that the attenuations per wave number are small, i.e., when the heterogeneities are weak. This radiative transfer equation governs the diffuse energy propagation as a function of space, time, and propagation direction. Solutions of the radiative transfer equation are presented for the …

Arts, Computers And Artificial Intelligence, Sol Neeman Ph.D.

Engineering Studies Faculty Publications and Creative Works

Science and art seem to belong to different cultures. Science and technology, mainly the products of the intellect, use terminology and vocabulary that are concise and well defined. In contrast, in artistic expression, ambiguity is a powerful component. Still the relationship between these two different categories of human activity is interesting and fascinating. In this paper, a general comparison of these two disciplines will be introduced. Then the possibility of mechanical creation of art using computers and artificial intelligence will be discussed. This will be followed by two techniques which are used to create poetry and music. First, a statistical …

Development Of Outcome Assessments At Wpi, William W. Durgin, Lance Schachterle

Office of the Provost Scholarship

The WPl PLAN, adopted by the WPl faculty in 1970, strongly anticipates current thinking about student outcomes assessments by structuring degree requirements that mandate that students demonstrate their ability to perform professional functions embodied in ABET Criteria 2000, especially Criteria 3 and 4. The WPI faculty has also practiced both student and self evaluations of these outcomes through respectively grades and peer review (both departmental and campus-wide) of student performance.

Local Stresses On Lateral Pipe-Nozzle With 45 Degree Angle Intersection, James Jin Xu

Dissertations

This dissertation presents a comprehensive study of local stresses, due to internal pressure around a pipe-nozzle with 45 degree angle intersection_ The resulting circumferential and longitudinal stresses on the pipe around the pipe-nozzle region are normalized as local stress factors and plotted as function of beta, β, (the radius of the nozzle/the radius of the pipe) and gamma, y, (the radius of the pipe/the thickness of the pipe) through the finite element method. The range of beta, [3, is from 0.1, to 1.0, and gamma, y, from 10 to 300. Comprehensive studies were made for the boundary parameters, such as …

Implementation Of Fortran Finite Element Analysis Source Code With Application : Particle Deposition In A 90 Degree Duct Bend, Pantaleo Loiacono

Theses

Two FORTRAN 77 finite element analysis source codes, by 1.N. Reddy, were input into a PC, debugged, executed, and tested successfully. These programs are available to students interested in implementing a good finite element analysis source code on a PC or on a workstation in one or two dimensions. The programs can solve problems relating to heat transfer, stresses, beam analysis, frames, trusses, plane elasticity, plate bending, and laminar viscous incompressible fluids with various node and element combinations.

The two-dimensional program was used to obtain the velocity distributions in a 90 degree duct bend with incoming and exiting fully developed …

Heat Transfer In Microchannels, Xianming Wang

Doctoral Dissertations

The objective of this research was to develop an analytical solution to the heat transfer problem in microchannels with slip-flow--a heat transfer problem for gases at low pressures or in extremely small geometries, and to verify this solution experimentally. In this investigation, an analytical expression for the velocity distribution with slip-flow was obtained which involved the Knudsen (Kn) number in an infinite series form. The result showed that the velocity always increased as the Knudsen number was increased. The Knudsen number for extremely small channels may become large enough to affect significantly the velocity distribution and consequently affect the heat …

Parametric Correlations For Generic Scramjet Combustors With Ramp-Type Injectors, Jason Granville Bush

Mechanical & Aerospace Engineering Theses & Dissertations

Development of an efficient scramjet combustor requires the use of computational models due to the cost of full-scale physical testing in the speed regime of Mach 10 through Mach 18. This study focuses upon the database generated by one such computational model, SHIP3D, which describes a generic scramjet combustor using ramp-type file! injectors. Three generalized parametric equations have been developed from this database, which describe the fuel-air mixing efficiency within the scramjet combustor as a function of normalized-axial combustor distance, ramp injector-region lift coefficient, and stoichiometry. It is shown that one of the three equations nearly models the trends as …

The Crash Simulation And Analysis Of The Friendly Mobile Barrier, Bryan Edward Marz

Mechanical & Aerospace Engineering Theses & Dissertations

Mass transportation is an ever increasing alternative being researched and evaluated in today's society. With the increase of demand for such transportation, an increase in safety is also needed. This research entails the analysis of a new idea, The Friendly Mobile Barrier, in railroad crossing barrier design. The design is meant to prevent any approaching vehicle from crossing a railroad track and be survivable for those impacting the barrier.

Research conducted involves the crash simulation and analysis of the Friendly Mobile Barrier. The Friendly Mobile Barrier was analyzed structurally using finite element analysis. An advanced lumped-mass mathematical model software, Crash …

Effects Of Initial Geometric Imperfections On The Behavior Of Graphite-Epoxy Cylinders Loaded In Compression, William Allen Waters Jr.

Mechanical & Aerospace Engineering Theses & Dissertations

The results of an experimental and analytical study of selected composite cylinders loaded in axial compression beyond buckling are presented. A comparison is made of buckling loads predicted by a nonlinear finite element code and those obtained from laboratory experiments. The initial geometric imperfections for each specimen were defined mathematically for inclusion in the finite element model. The experimental effort consisted of testing five graphite-epoxy cylindrical specimens. Four of the specimens were 16 plies thick; one of these had quasi-isotropic wall properties, another consisted entirely of angle plies, while the remaining specimens of this wall thickness were of two different …

Numerical Analysis Of Two And Three Dimensional Recessed Flame Holders For Scramjet Applications, Douglas L. Davis

Theses and Dissertations

This study investigated the flame holding properties of recessed cavities in supersonic flow using numerical analysis techniques. A simplified analytical model indicated that an important property for flame holding was the lower residence time. Several chemical kinetic rate models for hydrogen and hydrocarbon combustion were compared. The perfectly stirred reactor model also indicated that trace species diffusion should increase flame spreading rate, and that heat loss reduces flame holding limits. After nonreacting calibration, two-dimensional simulations confirmed the perfectly stirred reactor results for blowout limits. Also, the effect of trace species diffusion on flame spreading was shown to be negligible, and …

The Development And Evaluation Of The Knife Finite Element, Brett W. Clark

Theses and Dissertations

This thesis presents the development and evaluation of the knife finite element which is a degenerate case of a hexahedral element. The knife connectivity is an artifact of automatic all-hexahedral mesh generators. Currently, knives are propagated to the surface of the mesh for removal. However since this disturbs the surface mesh, other alternatives are needed. This thesis investigates the option of leaving the knife connectivity in the mesh and treating it as a valid finite element. The shape functions and stiffness matrix for the knife element are derived and evaluated using theoretical and practical evaluations. It is concluded that the …

Reaction Based Grasp Force Assignment, Mark W. Hunter

Theses and Dissertations

An iterative method is developed by which the contact forces required to apply an arbitrary wrench (six elements of force and moment) to a stably grasped object may be calculated quickly. The assignment of contact forces, given a required object wrench, is accomplished with the use of fuzzy logic. This concept is referred to as the fuzzy logic reactive system (FLRS). The solution is versatile with respect to goals inherent in the rulebase and the input parameters, and is also applicable for an arbitrary number of contacts. The goal presented in this research, to illustrate the concept of the FLRS, …

Rectified Synthesis Of Coupler Driven Four Bar Mechanisms For Two And Three Position Motion Generation, Ramanujam Thiruvenkatachari

Mechanical & Aerospace Engineering Theses & Dissertations

Four-bar mechanisms are widely used in the industry to solve a variety of motion problems. Till recently, their design was based on fundamental kinematics and brute force techniques, resulting in impractical designs and spurious linkages that failed to perform their desired functions effectively.

Procedures have been developed and implemented to guide the rigid body of crank driven four-bar linkages, through a set of design positions with techniques to avoid their defects. However, the practical applications of linkages used in the industry are coupler driven, with primitive synthesis procedures based on trial and error. The opening and closing of the hood …

A Progressive Damage Methodology For Residual Strength Predictions Of Center-Crack Tension Composite Panels, Timothy William Coats

Mechanical & Aerospace Engineering Theses & Dissertations

An investigation of translaminate fracture and a progressive damage methodology was conducted to evaluate and develop residual strength prediction capability for laminated composites with through penetration notches. This is relevant to the damage tolerance of an aircraft fuselage that might suffer an in-flight accident such as an uncontained engine failure. An experimental characterization of several composite materials systems revealed an R-curve type of behavior. Fractographic examinations led to the postulate that this crack growth resistance could be due to fiber bridging, defined here as fractured fibers of one ply bridged by intact fibers of an adjacent ply.

The progressive damage …

Numerical Prediction Of Turbulent Diffusion Flames Formed By Cylindrical Tube Injector, Ali S. Kheireddine

Mechanical & Aerospace Engineering Theses & Dissertations

This work summarizes numerical results for a diffusion flame formed from a cylindrical tube fuel injector, issuing gaseous fuel jet vertically in a quiescent atmosphere. Both pure fuels as well as fuel mixtures are examined. The primary objective is to predict the flame base height as a function of the jet velocity. A finite volume scheme is used to discretize the time-averaged Navier-Stokes equations for the reacting flow, resulting from the turbulent fuel jet motion. The turbulent stresses, and heat and mass fluxes are computed from the Reynolds stress turbulence model. A chemical kinetics model involving a two-step chemical reaction …

Lattice Truss Structural Response Using Energy Methods, Winfred Scottson Kenner

Mechanical & Aerospace Engineering Theses & Dissertations

A deterministic methodology is presented for developing closed-form deflection equations for two-dimensional and three-dimensional lattice structures. Four types of lattice structures are studied: beams, plates, shells and soft lattices. Castigliano's second theorem, which entails the total strain energy of a structure, is utilized to generate highly accurate results. Derived deflection equations provide new insight into the bending and shear behavior of the four types of lattices, in contrast to classic solutions of similar structures. Lattice derivations utilizing kinetic energy are also presented, and used to examine the free vibration response of simple lattice structures. Derivations utilizing finite element theory for …

Comprehensive Conjunctive-Use Management Of Connected Surface Water Groundwater Systems Using Stochastic Inputs And Uncertainties, Seshadri Suryanarayana

Civil & Environmental Engineering Theses & Dissertations

A comprehensive conjunctive-use management model is developed. The dynamics of flow and solute transport processes in connected surface water groundwater systems are integrated by a dual programming management model. The governing aquifer flow parameters and streamflows are treated as stochastic random processes. Multiple realizations of the random field are generated and are explicitly incorporated in a non-linear optimization model along with other system, environmental, and management constraints. To facilitate management of large aquifer systems, a linked simulation-optimization approach is used. The simulation program generates the response matrices for flow and transport processes. The management model then determines optimal well discharges …

Top Gear Manufacturing, B Mahadevan

IIMB Management Review

No abstract provided.

An Investigation Of The Characteristics Of Regenerative Heat Exchangers, Timothy J. Murphy

Theses and Dissertations

The objective of the current research was to investigate the effects of reducing screen thickness on the volume and compactness factor of stacked, wire-screen regenerators. An improved transient step-change method was devised which integrated experimental data with a numerical model of the flow to determine the heat transfer coefficient and friction factor. The improvements to the approach are: (1) the measured inlet temperature trace is used, (2) the heat transfer coefficient is based on a parameter called the sponge effect delay time, and (3) the important effect of the tube surrounding the matrix is included in the numerical model. The …

Simultaneous Composite Tailoring And Bending Control Optimization For Damping The Torsional Vibration Of A Plate, Douglas W. Dehart

Theses and Dissertations

A method for the simultaneous structural and control optimization for torsional vibration of a composite plate which simulates a spacecraft solar array structure was developed in this study. Included in the optimization of the plate are the location of the piezoceramic actuators and sensors that provide bending/torsion actuation, the control gains, and the orientation of the graphite fibers in the composite plies. This research included the effects of using composite tailoring to promote the coupling of the twisting-bending mode to enhance the damping system. The plate was modeled by classical lamination plate theory using a linear elastic strain-displacement theory. This …