Digital Commons Network^™

Characterization Of The Effects Of Waste Mullite Powder On Seawater Sea Sand Cementitious Materials, Xiao Sun, Zehui Zhou, Wenjie He, Yudong Bi, Yao Wang, Hengrui Liu, Rui Zhong, Hongyan Ma

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Maintaining the durability of coastal concrete structures while reducing construction costs remains a formidable challenge. Drawing inspiration from the volcanic concrete used by ancient Greeks and Romans, this study explores the feasibility of using waste mullite powder (WMP) with a high alumina content in seawater sea sand concrete to conserve natural resources and enhance durability. The experimental results demonstrate that the incorporation of seawater and WMP exerts detrimental impacts on the flow characteristics and workability of cementitious composites. While the sulfate content in seawater and sea sand can bolster the early strength of sea sand seawater concrete, sulfate attack compromises …

Geopolymer Clsm With Off-Specification Fly Ash And Bottom Ash: A Sustainable Approach To Hazardous Waste Utilization, Alexis K. Vandomelen, Ahmed A. Gheni, Eslam Gomaa, Mohamed A. Elgawady

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Conventional controlled low-strength material (CLSM) is a self-consolidating cementitious material with high flowability and low strength, traditionally composed of cement, sand, and water. This study explores the sustainable utilization of off-specification fly ash (OSFA) and bottom ash (BA), classified as industrial by-products with potential environmental hazards, to develop eco-friendly geopolymer CLSM as an alternative to conventional CLSM. Sodium hydroxide (NaOH) was used as an alkali activator to stabilize and solidify both two-part (liquid NaOH) and one-part (solid NaOH pellets) geopolymer CLSM mixtures. These mixtures were evaluated based on flowability (ASTM D6103-17) and compressive strength (< 300 psi per ACI Committee 229 guidelines for excavatability). A cost analysis was also conducted. The results demonstrated that incorporating OSFA as a cement replacement increased water demand by 15% to meet flowability requirements, while BA substitution for sand led to segregation challenges requiring mixture adjustments. For two-part mixtures, higher carbon content in OSFA necessitated an increased water-to-fly ash ratio. All self-consolidating mixtures exhibited 1-day compressive strengths ranging from 5 psi (0.03 MPa) to 87 psi (0.6 MPa). One-part mixtures showed a 1% to 34% reduction in 7-day compressive strength compared to two-part mixtures, improving excavatability. Increasing the BA-to-OSFA ratio from 1:1 to 3:1 reduced water demand due to lower surface area but increased the NaOH/OSFA ratio. This study highlights the potential of geopolymer CLSM to reduce costs by up to 94% at current NaOH prices (USD 6 per cubic yard) while repurposing hazardous industrial by-products, offering a cost-efficient, sustainable, and environmentally responsible solution for CLSM production.

Ftir Characterization Of Asphalt Sara Fractions In Response To Rubber Modification, Mohyeldin Ragab, Eslam Deef-Allah, Magdy Abdelrahman

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Asphalt–rubber binders (A-RBs) have a long and deep history of use; however, little is known regarding the interrelated chemical behaviors and miscibility of rubber with the asphalt fractions [saturates, aromatics, resins, and asphaltenes (SARA)]. This study comprehensively attempted to address this knowledge deficiency by employing Fourier transform infrared spectroscopy (FTIR) to investigate the chemical evolution of A-RBs. A-RB interacted at 190 °C and 3000 min⁻¹ for 8 h was deemed to have the optimal rheological performance. FTIR of the liquid fractions of A-RB 190–3000 showed a prominent chemical shift in the SARA fractions, with new peaks that showed rubber …

Stabilizing Embankments Using Geosynthetic Reinforcement, Daryl Greer, Charlie Sun

Kentucky Transportation Center Research Report

Reinforced soil slopes (RSSs) can be a feasible solution for embankments where there exist right of way re-strictions, environmental issues, rolling or mountainous topography, unfavorable geology, and other limiting fac-tors. They can be an alternative to retaining walls or importing select fills to construct steeper, stable embankment slopes where flatter embankment slopes may result in unwanted impacts, costs, and maintenance issues. Thisreport discusses the advantages and limitations of using geosynthetic reinforcement to construct RSSs. Researchers investigated current design, specification, and construction practices to determine which practices can be adopted by the Kentucky Transportation Cabinet (KYTC). Specifications were developed for using …

Characterization Of Lactobacilli-Containing Catheter Segments Developed By Using Selective Laser Sintered Mold., Caden Maners

Master of Engineering Theses

Catheter-associated urinary tract infections (CAUTIs) are a major healthcare burden with current prevention strategies offering limited success. This study presents a novel, self-coating biomaterial approach using a silicone-based bioink embedded with thermally sensitive probiotic strains (L. crispatus, L. rhamnosus, and L. reuteri). Catheter segments were fabricated via bio-injection molding using 3D-printed CAD molds. These Lactobacilli, selected for their probiotic and antimicrobial potential, serve as a non- antibiotic strategy to reduce infection risk. These segments were evaluated for mechanical strength (Shore A hardness), thermal stability (TGA/DSC), porosity and bacterial presence (SEM), biofilm formation (crystal-violet assay), as well as mass retention in …

Modeling Framework To Quantify And Gauge Project Cost Risks Due To Construction Material Price Volatilities Using Predictive Probabilistic Deep-Learning Algorithms And Stochastic Risk Modeling, Yasser Jezzini, Rayan H. Assaad, Islam H. El-Adaway

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Material price fluctuations pose significant challenges for executing construction projects and adhering to budgetary estimates. Existing research studies focused on forecasting construction material prices rather than quantifying and gauging overall project cost risks related to price volatilities, and they relied on traditional time-series forecasting methods that are incapable of offering full probabilistic distributions of price fluctuations and of providing a comprehensive assessment of risk uncertainties associated with material price fluctuations. This paper addresses these gaps by developing an integrated framework to quantify and gauge project risks due to construction material price volatilities. The framework's validity and practicality were demonstrated using …

Investigating The Thixotropy Of Fresh Struvite Cement-Based Composite: Insights On Mechanisms Of The Pastes’ Thixotropic Behavior, Ugochukwu Ewuzie, Abdulkareem O. Yusuf, Damilola Daramola, Monday Uchenna Okoronkwo

Chemical and Biochemical Engineering Faculty Research & Creative Works

Struvite (ST) recovered during wastewater treatment has been sparsely applied in cement-based composites. This study systematically evaluated the thixotropic behavior of cement-struvite (CST) pastes, a mix of 5–20 % ST by mass of cement, and proposed the interaction mechanisms leading to the pastes' thixotropy. The hysteresis loop area was used to establish the pastes' thixotropy and investigate its relationship with increased ST content, temperature, and yield stress. In the thixotropic behavior model used, the equilibrium shear stress was employed to examine the CST pastes' irreversible change; the characteristic time of deflocculation was used to study the flocs destruction process; and …

Gallium-Containing Bioactive Glasses: Their Influence On Ion Release And The Bioactivity Of Resulting Glass Polyalkenoate Cements, Lana Margaret Placek, Danielle Lee Perry, Mark Robert Towler, Anthony William Wren

Chemical and Biochemical Engineering Faculty Research & Creative Works

A series of glasses (0.48SiO2 − [0.40-x]ZnO − 0.12CaO-xGa2O3, x = 0, 0.8, 0.16) was developed to formulate a series of Ga-containing glass polyalkenoate cements (GPCs). The solubility of GPCs was tested using DI water, and it was found that the sample containing the highest mol% of Ga, LGa-2, had the most Ga ion release. The GPCs were incubated in SBF, and SEM/EDS analysis revealed that the at% of P increased, while the at% of Si decreased, highlighting the CaP precipitation on the GPC surface. The at% of Ga also decreased, reinforcing the Ga release from the GPC. Cellular testing …

Nasa Design And Analysis Of Pegda Hydrogels For Microgreen Cultivation In Space, Kelly Wu, Gabriel Antigua, Artur Abramyan

Publications and Research

With the growth of the space economy worldwide, sustainable and soil-less food systems for long-duration space missions become increasingly important. In this study, Polyethylene Glycol Diacrylate (PEGDA) hydrogels were experimented with as a biocompatible medium in arugula microgreen growth without utilizing soil. Among the most considerable challenges was the fact that the plants' root growth exceeded the hydrogel capacity, which caused seedling dislodgment and starvation. To combat this, computer-aided design (CAD) was utilized to 3D print different mold designs to try and control root development further. The most promising of these designs were coil and tree-branch molds, promoting lateral or …

Research On Technology Opportunity Identification By Integrating Technology Attribute Analysis And Competitive Environment Scanning —— A Case Study Of Industrial Robots, Daobin Gao

Journal of Scientific Information Research

[Purpose/significance] Placing technology opportunity identification in the perspective of technology attribute analysis and competitive environment scanning provides intelligence support for enterprises to select technology opportunities and formulate technology competitive strategies in complex and changing market competition environments.

[Method/process] Using patents as the data source, first, the BERTopic model is used to explore potential technical topics, Secondly, starting from the technical attributes, and from both global and local perspectives, we propose indicators of technical importance and technical attention, and use their cross screening to select candidate sets of technical opportunities, Finally, a market competition intensity index that takes into account market …

Analysis Of Vision Transformers And Domain Adaptation In Long-Range Facial Recognition, Zachary Michael Swanson

Department of Electrical and Computer Engineering: Dissertations, Theses, and Student Research

Atmospheric turbulence presents a significant barrier to long-range facial recognition, introducing severe geometric distortions and blur that degrade image quality. This thesis investigates deep learning approaches for mitigating these effects, with a focus on transformer based architectures and domain adaptation strategies.

An in-depth benchmarking study was performed using convolutional neural networks (CNNs) and vision transformers (ViTs) on the Husker BRIAR Research Collection from up to 500m (HBRC-500) face dataset. The results demonstrated that vision transformers, particularly hierarchical vision transformers like the shifted-window (Swin) transformer, outperform CNN-based models at long distances due to their ability to model global spatial relationships and …

An Exponential Cone Integer Programming And Piece-Wise Linear Approximation Approach For 0-1 Fractional Programming, Hoang Giang Pham, Thuy Anh Ta, Tien Mai

Research Collection School Of Computing and Information Systems

We study a class of binary fractional programs commonly encountered in important application domains such as assortment optimization and facility location. These problems are known to be NP-hard to approximate within any constant factor, and existing solution approaches typically rely on mixed-integer linear programming or second-order cone programming reformulations. These methods often utilize linearization techniques (e.g., big-M or McCormick inequalities), which can result in weak continuous relaxations. In this work, we propose a novel approach based on an exponential cone reformulation combined with piecewise linear approximation. This allows the problem to be solved efficiently using standard cutting-plane or branch-and-cut procedures. …

Advanced Study Of Nickel-Titanium Alloy: Effects Of Point Defects On Mechanical And Thermodynamic Properties, Diego Armando Juarez Rosales

Open Access Theses & Dissertations

High-throughput first-principles calculations of point defects are emerging as a powerful tool to accelerate materials discovery in applications [1]. Substitutional, antisite, and vacancy defects can play an important role in the mechanical and thermal properties of intermetallic alloys [2]. In this present work I compute the thermal and mechanical properties of shape-memory alloy nickel-titaniun (NiTi) in the B19â?? martensitic and B2 austenitic phases from molecular dynamics (MD), using a second nearest neighbor (2NN) modified embedded atom method (MEAM) [3] classical potential in the temperature range from 200K to 600K and composition range from 45 atomic percent to 55 atomic percent …

Optical And Thermal Characterization Of Vertically Conducting Β-Ga₂O₃ Diodes Grown On 4h-Sic Substrates For Short-Wavelength (<254 Nm) Detection, Muhammad Hassan Tahir

Theses and Dissertations

The advancement of compact, thermally stable, and efficient devices for deepultraviolet (DUV) detection below 254 nm is critical for solar-blind sensing, radiation monitoring, and high-power electronics. This thesis presents the growth, fabrication, and detailed optical and thermal characterization of vertically conducting β-gallium oxide (βGa₂O₃) Schottky barrier diodes (SBDs) grown on n-type 4H-Silicon Carbide (4H-SiC) substrates using metal-organic chemical vapor deposition (MOCVD).

β-Ga₂O₃ is an ultra-wide bandgap (UWBG) semiconductor (~4.8 eV) with intrinsic DUV transparency and high breakdown electric field, making it an ideal candidate for short-wavelength photodetection. However, its low thermal conductivity limits its vertical device performance. To overcome this, …

Design Of Supercritical Reactors To Understand Supercritical Water Oxidation Process And Hydrothermal Flames, Victor Dubceac

Theses and Dissertations

Supercritical water oxidation (SCWO) has been a topic of immense interest as an effective technique/tool for hazardous aqueous waste disposal. SCWO can be achieved by introducing an oxidizer (e.g., H2O2), or a hydrothermal flame as an internal source of both heat and oxidizer species in an aqueous environment at conditions above the critical point of water (P > 218 atm and T > 647 K). SCWO poses important environmental advantages for the treatment of harmful organic materials contained in waste streams. An SCWO reactor has the potential to be compact in design and therefore can be an ideal alternative to existing technology …

Effect Of Growth Conditions On The Performance Of Vertically Conducting Beta-Ga2o3 Diodes On 4h-Sic Substrate By Mocvd, Nifat Jahan Nipa

Theses and Dissertations

This thesis highlights the critical influence of doping strategies, specifically co-delta doping with silicon (Si) and indium (In), on improving the structural quality and device performance of β-Ga₂O₃-based Schottky barrier diodes (SBDs). To achieve better thermal management, β-Ga₂O₃ thin film was grown on bulk 4H-SiC substrates using the Metal-Organic Chemical Vapor Deposition (MOCVD) technique, renowned for its precise control over composition, thickness and doping profile. The ultra-wide bandgap (UWBG), high critical breakdown field and low turn-on resistance of β-Ga₂O₃ make it a strong candidate for next-generation power electronics and short-wavelength detection in extreme environments. However, the presence of structural defects …

Investing Hysteresis In Floodplain Dynamics Of Lakes In The Middle St. Johns River Using Sentinel-1 Sar Imagery, Keenan Hubbard

Doctoral Dissertations and Master's Theses

Floodplain dynamics are often complex, with hysteresis potentially affecting the temporal relationship between flood stage and flood extent during subsequent inundation phases. This study leverages Sentinel-1 synthetic aperture radar (SAR) imagery to map flood extent in the Middle St. Johns River Lake floodplains and examine the presence of hysteresis during flood events. SAR scenes corresponding to river gauge readings were analyzed from the rising and falling limbs of a flood hydrograph. By comparing these flood maps, we assess differences in inundated areas at equivalent water levels during each stage of the flood event. The findings aim to enhance flood monitoring …

Experimental Analysis Of Satellite Operator Training Using Game-Based Virtual Reality Simulation, Lana Laskey

Doctoral Dissertations and Master's Theses

Satellite data plays a vital role in modern global infrastructure by enabling communications, navigation, and weather forecasting. As demand for satellite technology grows, so does the need for highly trained satellite ground operators. Traditional training regimens for satellite operators employ simulation using two-dimensional computer console displays paired with the varied ability of trainees to generate abstract mental imagery of the scenario. However, this development of mental imagery imposes a considerable learning curve and cognitive workload on the trainee, which may negatively impact the user experience and knowledge gained during the training scenario.

This experimental study investigated the effects of game-based …

Effect Of Vehicular Electrification On Transportation Emissions In Florida, Shreya Sapkota Dhakal

Doctoral Dissertations and Master's Theses

Vehicular emissions from fuel-based passenger cars emit an array of gases and particles that are detrimental for human health and the environment. In that regard, electric vehicles (EVs) present a viable, sustainable solution. This study investigated the impact of electrification of passenger cars on air quality in Florida, in five major urban counties namely Miami-Dade, Duval, Hillsborough, Orange, and Leon. Between 2018 and 2022, these counties experienced a significant increase of 219.50 ± 52.32% in EV adoption, coupled with a 11.55 ± 6.13% decrease in fuel-based vehicle usage. Herein, we characterize five pollutants primarily generated from fuel-based passenger vehicles- carbon …

Mno2 Nanoscale Interface Modification, Alexander C. Skoppe

Doctoral Dissertations and Master's Theses

Interface modification of carbon fibers has been shown to improve the mechanical performance of composites. In addition, interface modification of carbon fiber composites can impart multifunctionality into the resulting composite. This work will explore ZnO and MnO2 as interface modifications for use on carbon fibers. When exposed to high temperatures, carbon fibers undergo fiber degradation, leading to the need for low-temperature hydrothermal processes. This work will develop and characterize a nanoscale ZnO and MnO2 interface modification for use on carbon fibers. These nanomodifications will be developed with low-temperature processes, minimizing the fiber degradation that the fibers undergo. Fourier transform infrared …

Mtu-Llm: Llm-Based Multi-Robot Task Allocation And Path Planning For Heterogeneous Robots In Search And Rescue Operations, Kaushik Kannan, Jungyun Bae

Michigan Tech Publications

Urban Search and Rescue operations after natural disasters involve locating and assisting victims in hazardous environments, which is challenging. Classical Multi-Robot Task Allocation (MRTA) and path planning approaches have been used to deploy heterogeneous robot teams in unsafe areas. However, existing methods often lack focus on workload balance and requirement fulfillment and struggle to generalize across different scenarios. To address these challenges, we propose Multi-robot Task allocation Utilizing LLMs (MTU-LLM), a framework designed to reduce the development time for task allocation and path planning approaches, enabling faster robot deployment. The framework uses an LLM-based “prompt engineering” approach that generates task …

Advancing Food Nutrition Estimation Via Visual-Ingredient Feature Fusion, Huiyan Qi, Bin Zhu, Chong-Wah Ngo, Jingjing Chen, Ee-Peng Lim

Research Collection School Of Computing and Information Systems

Nutrition estimation is an important component of promoting healthy eating and mitigating diet-related health risks. Despite advances in tasks such as food classification and ingredient recognition, progress in nutrition estimation is limited due to the lack of datasets with nutritional annotations. To address this issue, we introduce FastFood, a dataset with 84,446 images across 908 fast food categories, featuring ingredient and nutritional annotations. In addition, we propose a new model-agnostic Visual-Ingredient Feature Fusion (VIF2 ) method to enhance nutrition estimation by integrating visual and ingredient features. Ingredient robustness is improved through synonym replacement and resampling strategies during training. The ingredient-aware …

Experimentally Driven Numerical Model Of Carbon/Polyaniline-Based Glucose Monitoring Sensors: An Evaluation Using A New Figure Of Merit, Ziad Khalifa, Kyrillos Selim, Amira Ali, Sameh Abdellatif

Chemical Engineering

This study presents an experimentally driven numerical model for evaluating carbon/polyaniline (PANI)- based glucose monitoring sensors (GMSs), focusing on innovative configurations using graphene-PANI and carbon nanotube (CNT)-PANI composites. We performed a thorough analysis of the morphological, electrophysical, and electrical properties of these materials, ultimately leading to the extraction of key electrical parameters for integration into a finite element model (FEM). This model simulates the entire sensor, enabling the estimation of critical performance metrics such as sensitivity, limit of detection (LOD), linearity, and power consumption. Our findings demonstrate that the CNT-PANI configuration significantly outperforms the laser-induced graphene (LIG)-PANI electrode, achieving a …

Performance Enhancement In Rewound Industrial Retrofit Solutions For Five- And Six-Phase Permanent Magnet Assisted Synchronous Reluctance Machines, Kotb B. Tawfiq, Ayman M. El-Refaie, Peter Sergeant, Hatem Zeineldin, Ahmed Al-Durra, Ehab F. El-Sadaany

Electrical and Computer Engineering Faculty Research and Publications

This paper investigates upgrading aging three-phase Permanent Magnet Assisted Synchronous Reluctance Machines (PMaSynRMs) into multiphase configurations—specifically six- and five-phase windings—without modifying the existing stator or rotor laminations. This retrofit supports circular economic principles by extending machine life and reducing material waste and cost. Four configurations are examined: the original three-phase winding, asymmetrical six-phase winding, symmetrical six-phase winding, and five-phase winding. The feasibility of rewinding existing three-phase stators is explored for different slot/pole combinations. Balanced rewound five-phase windings are feasible only when the stator's slot/pole ratio is greater than or equal to 9. Both symmetrical and asymmetrical rewound six-phase windings are …

Advances In Noninvasive Imaging For Detecting Radiation-Induced Lung Injury (Rili), Austen Nissen, Said H. Audi, Anne V. Clough, Brian Fish, Amit Joshi, Meetha Medhora, Jason Walter Sidabras, Heather A. Himburg

Biomedical Engineering Faculty Research and Publications

Purpose: Dr. Richard Hill performed pioneering work in the field of radiation-induced normal tissue injury to the lung including noninvasive imaging studies aimed at identifying imaging biomarkers of radiation-induced lung injury (RILI). RILI is a life-threatening toxicity of radiation exposure relevant to both cancer patients undergoing thoracic radiation therapy (RT) and victims of accidental radiation exposure. The ability to detect RILI noninvasively has the potential to guide treatment planning for RT and, in the case of victims of acute radiation exposures, inform the decision to start mitigative therapies. As part of this special issue of IJRB honoring Dr. Hill’s many …

Designing A Portable And Accessible Diffuse Reflectance Spectroscopy System For Real-Time Detection Of Cervical Intraepithelial Neoplasia, Allison Scarbrough, Diana Moses, Tongtong Lu, Bing Yu

Biomedical Engineering Faculty Research and Publications

Significance: Over 80% of cervical cancer cases occur in lower-to-middle income countries (LMIC’s). This is partly because current screening techniques lack affordability, accessibility, and/or reliability for use in LMIC’s.

Aim: To develop an optical technique for cervical cancer screening that is affordable, accessible, and reliable for use in LMIC’s.

Approach: We developed a portable diffuse reflectance spectroscopy (DRS) system, which costs < $2500 USD to manufacture, and employs a Raspberry Pi to extract the absorption (μ_a) and reduced scattering (μ'_s) coefficients of biological tissue. The system was subject to travel and intentional rough handling. It was further used to capture 320 DRS spectra taken from 64 tissue-mimicking phantoms. Two …

Impactor Displacement As A Predictor Of Thoraco-Abdominal Organ Injury: Comparison Of Isolated Organ To Whole Body Tests., Jack Seifert, Jared Michael Koser, Alok Shah, Lance Frazer, Frank A. Pintar, Narayan Yoganandan, Dan Nicolella, Brian D. Stemper

Biomedical Engineering Faculty Research and Publications

Purpose

Body armor is used to protect the wearer from penetrating injuries. However, when the armor defeats the projectile, it deforms at high rates into the wearer, referred to as back face deformation (BFD). This deformation can cause a variety of superficial and internal injuries and consequently should be considered when designing body armor. However, current design standards do not adequately consider the effects of BFD, and new data are necessary to inform future design thresholds for BFD. The objective of this study was to develop blunt impact injury risk curves for in vitro thoraco-abdominal organs and determine their applicability …

Performance Characterization And Mechanistic Study Of Dry Process Wr/Sbs Composite Modified Asphalt Mixture, Hongfu Liu, Xiangyang Ren, Wenwen Ge, Zhengwei Yi, Dongzhao Jin, Xinghai Peng, Songtao Lv

Michigan Tech Publications

The dry process modification is characterized by simplicity, flexibility, low energy consumption, and low pollution, making it an ideal choice in pavement repair engineering. This study aims to optimize the use of waste rubber powder and SBS modifiers in dry process composite modification by preparing dry process WR/SBS composite modified particles (WR/SBS CMP) using a twin-screw extruder. The optimum mixing content of modified particles was determined through comparative analysis of pavement performance of dry process WR/SBS composite modified, wet-process SBS-modified, and matrix asphalt mixtures. The rheological properties and modification mechanism of the asphalt binder extracted from these mixtures were tested …

Eco-Friendly Additives For Biodegradable Polyesters: Recent Progress In Performance Optimization And Environmental Impact Reduction, Ahmad Fayyazbakhsh, Nima Hajinajaf, Hamed Bakhtiari, Michael Feuchter, Ilaria Improta, Ehsan Salehi, Sara Kamal Shahsavar, Marketa Julinova, Amirehsan Ghasemi, Bita Ghasemi, Reza Afsharnia, Marek Koutný, Young Cheol Chang

Research outputs 2022 to 2026

Biodegradable polymers have emerged as principal alternatives to petroleum-based polymers, which exert a detrimental impact on the environment. Among these, biodegradable polyesters stand out as particularly noteworthy, renowned for their exceptional properties that find application across diverse industries, including food packaging, biomedical devices, and agriculture. This comprehensive analysis delves into the impact of various additives, with a focus on eco-friendly ones, on biodegradable polyesters, as evidenced by recent research endeavors. The additives are systematically categorized to provide a nuanced understanding within distinct industrial contexts. In the exploration of these additives, a meticulous classification is employed, ensuring a focused analysis of …

A Comparative Study Of The Pullout Strength Of Geostraps And Geogrids In Reinforced Soil, Kshitij Gaur, Ashutosh Trivedi, Sanjay Kumar Shukla

Research outputs 2022 to 2026

The sustainable development of geotechnical infrastructure necessitates using durable, efficient, and environmentally resilient reinforcement materials. This study investigates the pullout performance of geostraps to assess their potential as a sustainable alternative to conventional geosynthetics. This study focuses on the pullout performance of geostraps, flexible, polymeric reinforcement materials. There has not been a thorough study of their pullout resistance, which directly affects the stability and durability of reinforced soil structures. Pullout tests were conducted on sandy soil in a controlled environment. The experimental findings from the pullout test were then validated in a numerical model. The model was used to determine …