Digital Commons Network^™

Design Of Non-Uniform Linear Antenna Arrays With Digitized Spacing And Amplitude Levels, Jack F. Morris

Masters Theses

"Recent developments in space exploration have shown a need for high resolution, high gain antennas. The introduction of non-uniform linear array theory has provided a means by which arrays may be designed to produce narrow main beams with fewer elements than required by uniform arrays. A general theory has not been developed, however, and the design engineer has been left with only trial-and-error methods with which to work. In this study a technique has been developed by which non-uniform antenna arrays may be synthesized to meet a given set of specifications with reasonable accuracy. The elements of the array are …

Instrumentation Of A Diesel Engine For Measuring Cylinder Head Temperature, And Pressure At Various Crank Angles, Raman A. Patel

Masters Theses

"In this investigation, an attempt has been made to measure the instantaneous pressures in the cylinder and the transient temperatures of cylinder head versus crank angle in a Diesel engine. A strain-gage pressure transducer and a sensitive surface thermocouple were used. The pressure transducer was practically free from temperature influence and strain effects caused by installation. It had a greatly reduced sensitivity to vibrations compared with other available types of pressure transducers. The thermocouple had a very short response time. A device enabling very accurate measurement of crank-angle was constructed. Appropriate quantities were displayed on the screen of an oscilloscope …

The Kinetics And Mechanisms Of The Reaction Of Benzyl Chloride With Potassium T̲-Butoxide In T̲-Butyl Alcohol, Der-Rong Chen

Masters Theses

"Benzyl chloride is a moderately reactive halide. Substitution of the Cl⁻ by other nucleophiles, e.g., HO⁻, AcO⁻, S₂O₃⁻, Br⁻ etc. proceeds almost quantitatively in solutions at convenient temperatures ... The object of this study was to investigate if the less basic t̲-butoxide in t̲-butyl alcohol would afford the same product, viz., stilbene; and, if so, by what mechanism. A study of the products and kinetics of the interaction between benzyl chloride and potassium t̲-butoxide in t̲-butyl alcohol therefore has been initiated"--Introduction, page 1.

The Effect Of Copper Upon The Eutectoid Reaction In The Zinc-Aluminum System, Paul Theodore Corcoran

Masters Theses

"A Leitz dilatometer was used to study the kinetics of the eutectoid reaction in the zinc-aluminum system and the effect of small additions of copper upon this reaction. Three alloys were investigated: a pure 78% zinc - 22% aluminum alloy; a 78% zinc - 21.9% aluminum - 0.1% copper alloy; a 78% zinc - 21% aluminum -1.0% copper alloy. It was found that this reaction was similar to the pearlite reaction in the iron-carbon system. The reaction occurred by diffusion processes and the products of the reaction looked similar to pearlite when examined under the microscope. Copper was found to …

Oxidation Of Ortho-Xylene To Phthalic Anhydride Using A Fluidized Bed Catalysis, Jyue-Sheng Wang

Masters Theses

"This investigation was conducted to study the vapor-phase oxidation of o-xylene to phthalic anhydride in a fluidized bed reactor. Parameters investigated during the study were temperature, molar ratio of air to o-xylene vapor, and space velocity. The catalyst used was vanadium pentoxide supported on a silica base and diluted with potassium sulfate. The studies were conducted on a laboratory scale"--Abstract, page ii.

The Effect Of Vegetation, Soil, And Rock Type On Runoff From Some Small Watersheds In Missouri, Anant Suthipas Narupon

Masters Theses

"A previous study of mean annual floods (Harbaugh, 1962) was based on watershed area, channel length, and channel slope of forty five small watershed in the State of Missouri. The present study investigates the effect of precipitation, soil distribution, vegetal cover, and underlying bedrock on annual peak rate of discharge. This study consists of statistical analysis by multiple correlations of additional quantitative data for nine of Harbaugh's forty five watersheds. Hydrologic data were obtained from the U.S. Geological Survey and U.S. Weather Bureau climatological publications. Distribution of vegetation was compiled from U.S. Department of Agriculture aerial photographs. Soil and rock …

An Analysis Of Pressure Build-Up Theory, Hansraj J. Patel

Masters Theses

"Various theories regarding the pressure build-up characteristics for producing wells are analyzed. The merits and limitations of each theory are discussed. The error involved in plotting the pressure build-up data for the case of well-bore pressure versus shut-in time is pointed out. Equations have been presented for the various quantitative determinations of reservoir properties which can be obtained from typical pressure build-up data. Utilizing all the previous methods presented in the literature, a recommended procedure for field application is proposed. One oil well and three gas wells have been analyzed using the recommended procedure with the attendant calculations given in …

Free Convection Heat Transfer From An Inclined Heated Flat Plate In Air, Shu Chien Yung

Masters Theses

"An experimental investigation has been performed to determine the free convection heat transfer from a heated flat plate in air moved from the vertical position through three inclined positions to the horizontal position. The hot surface of the plate was facing downward for the horizontal and three inclined positions. Tests were performed at plate surface temperatures from 120°F up to 404°F. Data for the plate surface temperature at about 165°F with the plate in the vertical position agrees very well with previous experimental work. This same data was used to determine a new parameter, introduced into the Pholhausen free convection …

An Apparatus To Measure Capillary Jet Thrusts And The Evaluation Of Normal Stresses In Fluids, Charles Donald Green

Masters Theses

"The purpose of this work was to design, construct and calibrate simple, inexpensive apparatus which could be used to measure the normal stresses and tangential shear stresses of a fluid. For normal stress measurements, the capillary jet thrust principle was selected. A standard analytical balance was modified so that capillary tubes could be fitted on it horizontally. It was designed so that the thrust produced by a jet of fluid from the tube caused a deviation from the zero balance position. The weights needed to rezero the balance gave a measure of the thrust"--Summary, page 1.

On Time-Optimal Second Order Discrete Control Systems, Chao-Tai Li

Masters Theses

"The time optimal control problem in unforced discrete systems is studied in this thesis. Comparison is made between the discrete and the continuous control systems by means of minimum time isochrones. concerning optimal time, it is shown that using the discrete control system will take at most one more sampling period of time to go to equilibrium. An investigation is also made for the case when the time constant of the physical plant, G(s), and the control model are different. In such a case, an optimal trajectory can not be obtained. An adaptive process is proposed to adjust the model …

The Shear Graph And Cohesive Soil, Charles Rees Nickerson

Masters Theses

"Some existing test procedures for measuring shearing properties of soils are reviewed. the correlation between the shear strength of two fine-grained soils as indicated by the unconfined compression test and the shear graph test is investigated. This is accomplished by comparing the test results at varying moisture contents and dry densities. One of the soils used is a red plastic clay, the other a silty clay. The test results indicate that for soils wet of optimum the shear graph strength can be taken as being equal to the unconfined compressive strength. This will be conservative for soils that exhibit an …

A Study Of Degradation In The Pumping Of Dilute Polymer Solutions, I-Chung Chang

Masters Theses

"In the course of an investigation of the turbulent flow properties of dilute high polymer solutions in organic solvents, a number of supplementary investigations were required. These were: 1. Determination of the molecular weights of a number of polymers by intrinsic viscosity measurements. 2. Determination of the effect of pumping on the degradation of high polymers in dilute solutions. This included development of a method for estimating the concentration of dilute polymer solutions. 3. Determination of the effects of density, viscosity and non-Newtonian behavior on the calibration of turbine flow meters"--Introduction, page 1.

The Production Of Glutamic Acid By Fermentation, Tsun-Hsiung Li

Masters Theses

"The method of producing glutamic acid by fermentation was studied in shake flasks and in a five liter fermentor. Strains of the micro-organism, Micrococcus glutamicus, were used to produce glutamic acid under different conditions ... A literature review of the general properties of glutamic acid and industrial methods of glutamic acid production was made. A detailed discussion of the fermentation method of glutamic acid production was also included"--Abstract, page ii.

Radiation Induced Polymerization Of Methyl Methacrylate, Ko-Hung Liu

Masters Theses

"A study has been made of the gamma radiation effect on the rate of polymerization of methyl methacrylate monomer, and also to determine the effects of the presence of clay of known composition and of other solids on the rate of polymerization. The results indicate that the monomer undergoes polymerization and then degradation as a function of radiation time at a given gamma flux"--Abstract, page ii.

An Introduction To Linear Time-Variant Digital Filtering Of Seismic Data, Richard Harold Lassley

Doctoral Dissertations

"The exploration geophysicist is constantly searching for new and better methods for analyzing seismic data. The primary purpose of this dissertation is to introduce linear time-variant digital filters as a technique for the filtering of seismic data. Methods of characterizing linear time-variant digital filters are discussed in general terms. The advantages of the different impulse and frequency responses are cited. In addition, the meanings and possible interpretations of the time and frequency variables introduced are considered. The concept of linear time-variant digital delay filters is presented along with their relationship to impulse responses. A pictorial diagram of discrete time-variant impulse …

Permeability And Additive Absorption And Extraction In Lubricating Greases, Eugene Hsiung-Jen Tu

Masters Theses

"A permeability apparatus was used to measure the permeability coefficients of eight Lithium-Calcium greases and ten Baragel greases in which the viscosity and type of the oil component were varied. The oil present in each grease was used for its permeability measurement.

An improved sample packing technique was developed to improve the repeatability of permeability measurements. Repeatability of ± 3% was achieved. In general the permeability coefficients of the non-soap Baragel greases were higher than those of the lithium-calcium greases with comparable oil components, and those of greases containing paraffinic oils were higher than these containing naphthenic oils. The effect …

The Prediction Of Mix Design Properties For Dense Graded Bituminous Mixtures, Robert Ernest Weeks

Masters Theses

"The purpose of this investigation was to ascertain the feasibility of interpolating values of the physical properties of a dense graded bituminous mix between known values. Also the effects of limestone mineral filler on the properties of a dense graded mix are evaluated. The variables in this study were mineral filler and asphalt cement. Control mixes were established at 2, 6 and 10 percent mineral filler and experimental mixes were prepared at 4 and 8 percent filler. The aggregate consisted of limestone and was mixed with an asphalt cement of 85-100 grade penetration. Al mixes were tested by the Marshall …

A Circularly Polarized Corner Reflector Antenna, Walter Ronald Koenig

Masters Theses

"Image theory is used to develop the far field and polarization equations for a ninety degree corner reflector antenna. These equations are in terms of spherical coordinates, the length of the dipole element, the distance of the dipole from the corner of the reflector, and the angle of tilt of the dipole element with the apex of the corner. The equations are simplified to give the far fields in the vertical and horizontal planes for the special case of a half-wavelength dipole. An expression to calculate the distance of the dipole from the corner necessary to give circular polarization broadside …

Radial Water Encroachment - An Approximation, Tommie C. Wilson

Masters Theses

"This presentation consists of the application of empirical equations for the calculation of the water influx into a radial oil reservoir in which the history of the rate and cumulative water influx are equated to the pressure decrements and time. This new analysis, based on William Hurst's solution for the steady-state water influx, yields an accurate method for determining water influx through the application of simple linear empirical equations. These linear approximations reproduce the rigorous influx solutions to a maximum deviation of 1.6 per cent"--Abstract, page ii.

Stability Determination By Liapunov's Method In Nonlinear Control Systems, Neng-Chung Liao

Masters Theses

"An introduction to Liapunov's second method as it applies to control system stability is presented in this work. Main theorems and definitions of Liapunov's method are treated. In particular, Lur'e's method and Szego's method for testing the stability of a nonlinear system are presented, and several examples are used to illustrate these procedures"--Abstract, page ii.

Use Of Spent Sulphite Liquor For Stabilization Of Fractured Rock And Sealing Off Water Bearing Formations, Laxman Singh Sunda

Masters Theses

"The paper industry, in its process of manufacturing pulp from wood, produces large quantities of a substance called lignin, lignin sulphite, or lignosulphonate. This material has been disposed of as a waste product; however, it does have many potential uses. In this investigation, lignosulfonates were used as agents for bonding rock sections together and, as the chief component of gels, for filling the pores of artificial rock cores. The purposes of these tests were to find how this substance could be used in the mining industry, for stabilizing fractured ground around mine openings and for sealing off water influx into …

Effect Of Calcium Lignosulfonate On Properties Of Concrete At Early Ages, Lawrence Kong-Pu Wang

Masters Theses

"The objective of this investigation was to determine the effects of calcium lignosulfonate on the physical properties of concrete. Calcium lignosulfonate used as an admixture was tested for its effect on the tensile and compressive strength of plain concrete cylinders, and for its effect on the flexural strength of plain concrete beams. The effect of the admixture on shrinkage, slump, air content and unit weight was also studied. the test results showed that calcium lignosulfonate reduces the amount of water required to make a workable concrete mix; a more workable mix saves money because it is easier to place, thus …

Solid Solubility Of Sulfur, Selenium, And Tellurium In Molybdenum At 1100°C, Lattice Constants Thermal Expansion Coefficients, And Densities Of Molybdenum And The Molybdenum-Base Alloys, Ramesh Purushottamdas Shodhan

Masters Theses

"With the ever increasing requirement for engineering materials having adequate mechanical properties at ever higher temperatures there has been, in quite recent years, a considerable increase in the study of molybdenum and molybdenum-rich alloys. Since 1945 extensive information on the engineering properties of molybdenum and molybdenum-base alloys has gradually become more available ... The present work involves the determination of solid solubility of elements with large atoms such as sulfur, selenium, and tellurium in molybdenum at 1100°C using the parametric method. Furthermore, the thermal expansion coefficients of pure molybdenum and of molybdenum-base solid solutions containing the elements just mentioned were …

Discharge Characteristics Of Side Weirs, Edgar Snowden

Masters Theses

"The purpose of this study is to investigate the division of flow of water in a flume of rectangular cross-section when the flume is provided with a side weir. An equation has been derived so that the quantity of water flowing over the side weir compared to the quantity of water flowing in the main channel can be predicted. This ratio is acceptable only within the ranges of heads, velocities, and weir lengths imposed by the geometry of the system tested"--Abstract, page ii.

The Effect Of Cadmium On Anaerobic Digestion, Lyle Lynn Pruitt

Masters Theses

"The main purpose of this study was to determine the effect of cadmium on anaerobic digestion. Metal concentrations in the form of regular and slug doses were considered. The possibility of acclimating anaerobic bacteria to higher cadmium levels was studied, and attempts were made to reestablish digestive action through re-seeding in digesters overcome by high cadmium concentrations"--Abstract, page [ii].

The Design Of A Sensitive Probe For Mass Flux Measurements Of Water Vapor In Air, Devendra Vaikunthlal Mehta

Masters Theses

"This investigation pertains to the construction and investigation of a sensitive probe to determine the possibility of measuring the mass flux of water vapor in air under non-flow steady state conditions. The probe was a small electrolysis cell is which the electrolyte (partially hydrated phosphorus pentoxide) was used as the sensing element. The rate of mass transfer was determined by measuring the amount of direct current flowing through the acid film"--Abstract, page i.

Linvill's Model As Applied To P-N Junction Photo-Diodes, Rudy Michael Chittenden

Masters Theses

"The problem undertaken in this study is to present a performance evaluation of Linvill's model as it pertains to the p-n junction photo-diode. The evaluation is performed by comparing the distributed mathematical solutions, the solution obtained using Linvill's lumped model, and the experimental measurement of the transient voltage rise across a photo-diode due to a unit-step pulse of light incident on the junction. Despite the absence of a suitable light source for use in the experimental measurement, it is concluded that Linvill's model provides an excellent means to determine the risetime of a photo-diode. This is provided that the photo-diode …

The Effect Of Varying Sea Coal Fineness On Sea Coal Activity In Molding Sands, Laurence A. Cooley

Masters Theses

"An experiment was conducted in an attempt to establish a relation between sea coal activity in a facing sand and the particle size of the sea coal added to the sand. It was felt that if a sufficient difference in distribution of volatiles was detected, a correlation between particle size and activity of the sea coal within the test specimens might be established. The lack of positive evidence to support such a relationship is indicative that a variation in particle size does not promote volatile re-deposition within the range of particle sizes investigated for the particular weight per cent of …

Anodic Dissolution And Disintegration Of Tin And Valency Of The Tin Ions Going Into Solution, Mrityunjoy Dutta

Masters Theses

"The increased demand for protective coatings on metals and for non-corrosive alloys has stimulated extensive research on the fundamental behavior of metals in corrosive media. One of the problems still unsolved is the nature of the mechanism of the anodic dissolution of metals like beryllium, zinc, magnesium, cadmium, tin, aluminum, iron in aqueous salt solutions. It has been reported in the literature that these metals show discrepancies which often arise between coulometric data and the weight loss of metal electrodes in various media. Several investigators have proposed different and opposing theories to explain the above deviation. The purpose of the …

A Study Of Sulfide Inclusions In Medium Carbon Steels, Shane Shiang Yen

Masters Theses

"Sulfur is a very important component in steel. Usually is it present as an impurity in commercial steels. In these materials the sulfur content is 0.05 percent maximum but may be higher or lower than this in some steels...It is generally believed that sulfur has a deleterious effect on the mechanical properties of steels. Originally this investigation was to deal with this aspect of sulfur in steels but the work did not progress to this stage. An effort was made to vary the nature of the sulfides in several experimental heats of steel by controlling their composition. Variation in the …