Digital Commons Network^™

Stresses In A Thick Spherical Shell, David Wayne Moore

Masters Theses

"This thesis reports a method to evaluate the stresses in a segment of a thick spherical shell. In the numerical examples loads due to thermal expansion as the shell is constrained at the free edge and a dead load acting vertically downward were considered for a shell assumed pinned but free to rotate and for a shell assumed completely fixed at the edge. A concrete shell was specifically studied but the method would also apply to a shell of any homogeneous, isotropic material"--Abstract, page i.

Small-Signal Impedance Of A Junction Diode At High Injection Levels, John E. Lundy

Masters Theses

"A mathematical expression for the driving point impedance of a junction diode at high injection levels is developed. To evaluate the impedance versus frequency characteristic of a diode, it is necessary to know the minority carrier lifetime as a function of injection level and doping density in the base (lightly doped) region, the junction area, and the base width. The interesting characteristic of the diode impedance at high injection levels is the inductive reactance displayed by the diode.

The expression is developed by solving the differential equation for charge flow in the base region of a diode assuming space-charge neutrality …

Convective Heat Transfer In Small Cylindrical Enclosures Heated From Below, Donald Wayne Land

Masters Theses

"Free convection in enclosed air spaces is often of prime importance in the design and analysis of panels utilizing the insulating properties of air and other gases. Previous investigations were performed on very thin air layers.

This thesis presents the results of an experimental investigation to determine the heat transfer by convection and conduction through air layers with relative sizes in terms of length/diameter ratios of one-fourth to one.

Eight cylindrical samples were tested. Four had inside diameters of 2.0 inches, and the others were 2.75 inches in diameter. Heat was transferred across the air layers by both conduction and …

Some Aspects Of Transient Flow Behavior In Artesian Aquifers And In Hydrocarbon Reservoirs Surrounded By Artesian Aquifers, Alton John Nute

Masters Theses

"An analysis of the principal theories concerning the transient movement of water in artesian aquifers and from artesian aquifers into hydrocarbon reservoirs is presented. Various analytical methods which can be applied to depict the behavior of these two types of aquifer systems are compared.

Most aquifer studies to date have been based upon the Thesis Non-Equilibrium Formula. This equation has been used to calculate the coefficients of storage and transmissibility for aquifers; to evaluate well performance; and to investigate problems concerning recharge, movement, and discharge of aquifer water. However, one problem which still remains is that of accurately predicting the …

Collision And Pursuit Course Terminal Closures For Spacecraft To Satellite Rendezvous, John Anthony Campbell

Masters Theses

"Collision and pursuit course closure maneuvers were studied for correcting position and velocity errors in the terminal phase of spacecraft to satellite rendezvous.

Minimum values of the ratio of initial range to velocity necessary to achieve rendezvous were determined for collision closures as a function of the initial line of sight. The time and velocity increment required for rendezvous were computed as a function of initial conditions.

Pursuit closure maneuvers were analyzed and time and velocity increments defined as a function of initial range, closing velocity, line of sight angle and angular velocity.

The velocity increments required were significantly higher …

A Multiple-Input Chemical 'Memistor' For Adaptive Circuits, Richard Franklin Crall

Masters Theses

"A modification of Widrow’s "memistor" is made in a form suitable for extension to multiple-input devices. This modified form is extensively investigated using analog field maps, and through experimental testing. The multiple-input device presented exhibits good adaptive characteristics and reduces the number of interconnections required in the external circuitry"--Abstract, page ii.

Matrix Computer Analysis Of Curvilinear Grid Systems, David Leon Fenton

Doctoral Dissertations

"A general equilibrium-stiffness method of matrix structural analysis was adapted and applied to the solution of the member end forces and moments of each of the members in a curvilinear structural grid system. A structural system of this nature is commonly used as the supporting framework for a "steel-framed dome", in addition to being a basic structural component in many aerospace applications. An integral part of the development of the analysis was the development of a computer program to perform the many complex operations required to obtain the solution. The engineer, by supplying the appropriate structural data and load data …

Determining The Transfer Matrices Of Tapered Multiwire Transmission Lines, Clyde A. Vandivort

Masters Theses

"The advent of monolithic and integrated microelectronic circuits has aroused interest in passive multilayered thin film networks. The basic thin film network is shown in Figure 1. This structure consists of alternate resistive and dielectric layers sandwiched together. Such devices are referred to as distributed parameter RC networks. The reduction of volume and increased reliability offered by thin film devices has caused considerable effort to be extended in the analysis of their characteristics....

The incremental equivalent circuit given in Figure 2 stems directly from the above physical parameters and is the circuit used as a basis for the analysis that …

Plastic Deformation Of Thin Plates With A Spherical Indenter, Benjamin Jen-An Chang

Masters Theses

"A method of determining the stress distribution in a thin plate deformed with a spherical indenter is presented in this report. The analysis is formulated in cylindrical coordinates and utilizes the basic principles of plasticity (von Mises yield criteria, Luwig stress-strain equation, Hencky Deformation theory, etc.). The problem is solved through the utility of a displacement function that, by virtue of its definition, automatically assures that the condition of volume constancy is satisfied. The boundary conditions are selected on the basis of having average, or integrated, effects corresponding to the physical constraints of the problem. Numerical integration is introduced to …

Some Effects Of Nickel On The Microbial Population Of Activated Sludge, Virgil Eugene Carr

Masters Theses

"The purpose of this investigation was to study the effects of nickel on the microbial population of activated sludge, to establish a relationship between effluent quality and changes in microbial population, and to determine the fate of nickel applied. Five one liter fill and draw activated sludge units were fed settled domestic sewage and received constant daily nickel doses of 1-10 mg/l, and a 50 mg/l slug dose applied after 27-30 days of operation. The parameters used were the chemical oxygen demand (COD) of the effluent and membrane filtered effluent, mixed liquor and effluent total suspended solids, mixed liquor volatile …

A Class Of Pattern Recognition Machines, Shaw Yih Chung

Masters Theses

"The classification of signals through the use of pattern recognition techniques may be viewed as a statistical classification problem since at least some pattern classes are analog signals which have been contaminated by additive noise. In order to represent these signals at the input of a pattern classifier they are sampled and a vector and an m-dimensional vector space used to describe the pattern. Consequently, these pattern samples are processed to determine the parameters of the statistics. In this study the additive noise was assumed to be Gaussian in nature. This study was based on a priori knowledge of the …

Synthesis Of Filters Using Distributed Rc Networks, Mario Nader Nader

Masters Theses

"This paper deals with the problem of realizing filter and delay functions by means of distributed RC devices. The method is made possible through the use of a distributed RC network which possesses rational admittance parameters. The technique of approximating transfer functions using polynomial factors that are ration in e[superscript (a square root of s] is explained. These factors are used to approximate the magnitude and phase characteristics for a low-pass filter. This filter is then realized using the admittance functions studied by Wyndrum, the "s->W" transformation, and Richard's theorem. Those factors are then used to approximate high-pass and …

Relationship Of Feldspar Properties To Surface And Volume Defects In Porcelains, Macy Wiiliam Vance

Masters Theses

"Four levels of particle size distribution and four compositions of feldspar ranging from high-potash to high-soda content were evaluated in their effect on body and surface defects and selected engineering properties of an electrical porcelain. It was found that surface blistering defects occurred at a high incidence in porcelain specimens slightly overfired at 1225⁰C in a body composition containing 33% albite (soda), 67% high-potash feldspar blend and a relatively coarse, 140 mesh grind, of the feldspar. The occurrence of surface and volume blisters was correlated with the formation of a microscopic bleb structure in the porcelain matrix. It was also …

A Shunt-Feed Antenna System On A Small Supersonic Aircraft, Larry Joseph Nanney

Masters Theses

"A technique was developed which successfully predicted the reactance of a shunt cavity exciting the air frame of a small supersonic aircraft as an antenna. This was possible by the use of the wire above a ground place approximation which closely defined the characteristic impedance of the shunt fed cavity. A correlation was made between the maximum values of parallel resistance of the shunt fed cavity and the length of the air frame or portions of the air frame, which at this point were found to be a quarter wavelength in length. Measurements of the impedance of the shunt-feed system …

Hydrologic Characteristics Of Shallow Bedrock Aquifers In The Vicinity Of Norman Creek, Central Phelps County, Missouri, Michael A. Nawrocki

Masters Theses

"Groundwater is becoming increasingly important as a source of water supply in the United States. Consequently, the prediction of well yields is a vital concern. In order to predict the quantity of water which can be reduced from a given aquifer it is necessary to know the aquifer's hydrologic characteristics. Many theoretical formulae have been derived for determining the aquifer characteristics. To date, these formulae have been tested mainly on unconsolidated and clastic rock aquifers. It has never been shown that these formulae can also be consistently applied to carbonate aquifers which underlie regions of karst terrain. This paper summarizes …

Optimum Fin Spacing For Heat Transfer Per Unit Length Of Heat Exchange Section, Glenn Ellis Miller

Masters Theses

"This thesis presents the results of an experimental study of the heat-transfer ability of a finned surface as a function of the spacing between fins. The results are expressed as heat transfer per unit length of finned section rather than the heat transfer per fin. Circumferential steel fins, seven and three-quarter inches in diameter, were used for the investigation. Data was taken for fin spacings ranging from zero to one and one-half inches. The experimental heat-transfer rate to atmospheric air was determined by measuring the volume of saturated steam which condensed in the test section over a measured time interval. …

The Influence Of A Fixed Failure Plane On The Direct Shear Test, Kenneth Hodges Bell

Masters Theses

"The analysis of the direct or box shear test for determining the shear strength of a soil makes use of the assumption that the failure plane coincides with the plane of separation between the two halves of the box. Hvorsley, Roscoe, Hansen and others have theorized and experimentally shown that this is not always the case. The stress distributions on the failure plane, however it may be oriented, are not as uniform as generally assumed. This investigation was carried out to compare direct shear tests run on granular, air dry material where the failure was allowed to take place naturally …

Estimation Of Regional Trends In Gravity Using Gram Orthogonal Polynomials, Stanley Dean Thompson

Masters Theses

"A computer program is presented which estimates the trend in a rectangular array of gravity measurements. It is assumed that the regional trend of gravity may be estimated by a low-order polynomial. The method of least-squares is applied to solve for the low-order polynomial which best approximates this trend. Gram orthogonal polynomials are used in the solution of this least-squares surface fit. The program is tested on a known polynomial and on some hypothetical Bouguer gravity data and found to approximate the ʺregional trend of gravity in these cases. The importance of eliminating any significant noise in the observations before …

Minimization And Generation Of Next-State Expressions For Asynchronous Sequential Circuits, Gary Keith Maki

Masters Theses

"One step in the synthesis procedure for realizing an asynchronous sequential circuit that is operating in fundamental mode is to obtain an internal-state assignment that will realize the operations of the circuit. Often the procedures that are used in accomplishing the above task generate several satisfactory assignments. The first part of this paper presents a method that will enable one to predict which of the internal-state assignments will yield a simpler set of next-state expressions. A second topic treated in this paper is one of presenting a method to generate the next-state expressions for an asynchronous sequential circuit directly from …

Scanning Properties Of Unsymmetrically Loaded Aperture Arrays, Gary Dean Brunner

Masters Theses

"Radiation patterns resulting from an array of waveguide-fed apertures, filled with assymmetrically [sic] cut dielectric inserts, in an infinite ground plane were investigated. The results of Blumberg and Hemmen concerning single apertures were applied to a two-aperture array, with emphasis upon obtaining an array capable of scanning in the far field through changes in the permittivity of the assymmetrically [sic] cut dielectric inserts. Scanning was shown to be possible with up to a 60⁰ scan angle with a "push-pull" method of varying permittivities, in which the permittivity of one insert is raised while the other is lowered. The aperture field …

The Measurement Of Explosively Induced Stresses In Rock-Like Materials With A Capacitive Transducer, Vincent Paul Crane

Masters Theses

"A capacitive transducer was developed for measuring the free surface motion in Hydrostone blocks loaded by an explosive plane wave generator approximately one foot from the specimen. The charge to specimen distance was adjusted to produce a single spall, the position of the fracture being noted on the recovered specimen. The longitudinal wave velocity in each specimen was determined by the ultrasonic pulse technique before each shot. From the above measurements the stress, strain and strain rate at the point of fracture were determined. An attempt was made to determine the actual fracture time with imbedded [sic] conductive graphite rods, …

Quality Of Surface And Subsurface Water In A Missouri Carbonate Karst Terrain (Dry Fork, Norman, And Benton Creek Watersheds), James Chi Huang

Masters Theses

"Little is known about the effect of carbonate karst terrain on water quality in the United States. Karst topography occurs over a large portion of Missouri and over a significant part of other midwestern states. The objectives of this study were the determination of the quality of surface and subsurface water in carbonate karst terrain and the investigation and evaluation of the effect of rainfall and runoff on water quality in the Meramec Spring area, east of Rolla, Missouri, during both the dry and wet seasons over the period of one year. Water samples were collected at a large number …

Velocity Profiles In Viscoelastic Drag Reducing Solutions, Luis Gustavo Florez E.

Masters Theses

"Turbulent velocity profiles in viscoelastic drag reducing solutions were measured using hot-film anemometer and Pitot tube techniques. Data were obtained in a solution of one per cent aluminium [sic] dioleate in toluene and in 0.2 and 0.4 per cent solutions of polyisobutylene (PIB) L-200 in cyclohexane. Velocity profiles were also obtained for comparison in toluene and cyclohexane by both techniques. By integrating the Pitot tube velocity profiles, large flow rate discrepancies between integrated and measured flow rates were found for the drag reducing polymer and soap solutions. This discrepancy was not observed in the hot-film anemometer measurements. The hot-film anemometer …

Fault Detection In Combinational Networks, Alexander Rahm

Masters Theses

"This paper presents an algorithm for locating a failure in combinational logic networks, which is a problem of importance in the maintenance of computer systems. The procedure is based on the "path sensitizing" idea for fault detection. The networks considered are non-redundant, consisting of AND, OR, and NOT elements. The class of faults investigated is that which causes a connection to appear to be logically suck-at-one or stuck-at-zero, and only single failures are treated. It is shown that the failure is generally located to a specific "fault group"--Abstract, page 2.

A Comparison Of Strength Properties Of Heat Treated Aisi 1065 Steels At High Strength Levels, Robert Lowell Hollenbeck

Masters Theses

"Six AISI C 1065 steels were heat treated and tensile tested in order to evaluate their ductility at high strength levels. Heat treating and tensile testing procedures were developed for use working with these steels at tensile strengths of 300,000 psi and higher. The austenitizing procedure in the hardening operation was found to affect the strength and ductility of the high strength samples. Rapidly heating to the austenitizing temperature followed by an immediate quench produced better properties than slow heating followed by a soaking period before the quench. However, it was concluded that the carbon contents of the steels studied …

A New Performance Index For Sensitivity And Energy Optimization., Mohamed Zafer Dajani

Masters Theses

"The principal aim of this thesis is to present a new index of performance which when minimized will simultaneously optimize the system energy and sensitivity function of a multivariable linear control system. With this performance index it is usually desirable to discriminate between the sensitivity factor and the energy term by weighting them differently. Two types of weighting factors are presented. Since it is not easy to minimize that performance index for all types of problems, further research is suggested to find methods of solution for such problems. Illustrative examples demonstrate the optimization process and the type of assumptions needed …

A Study Of The Compressibility Of Silty Soils., Marvin L. Byington

Masters Theses

"This study has been conducted to determine the applicability of the Terzaghi Theory of Consolidation and to determine the compressibility of silt soils with varying clay content. A pure silt was extracted from the Lebanon Silt Loam and mixed with varying amounts of the Onyx Cave Illite-Chlorite Clay. The compressibility of these mixtures was determined and an attempt made to apply the Terzaghi Theory in the analysis. It was found that the compressibility of soils high in silt content is very low. It was also found that the Terzaghi Theory may be applied to mixtures of 15 percent or more …

Hot‐Film Anemometry Measurements Of Turbulence In Pipe Flow: Organic Solvents, Gary Kent Patterson, Jacques L. Zakin

Chemical and Biochemical Engineering Faculty Research & Creative Works

Longitudinal turbulence intensities, autocorrelations, and energy spectra have been measured in the flow of toluene, benzene, and cyclohexane in smooth, round 1‐ and 2‐in. I.D. tubes. These measurements were made with a constant‐temperature hot‐film anemometer and covered radial positions from the center to r/a = 0.85 in the 2‐in. tube and to r/a = 0.75 in the 1‐in. tube. The turbulence intensity data were found to be similar to those obtained for air in a 10‐in. pipe by Laufer. A slight diameter effect was observed, the intensities in the 1‐in. tube being slightly lower than those in the 2‐in. tube …

The Mechanism Of The Electrooxidation Of Acetylene On Gold, James W. Johnson, J. L. Reed, William Joseph James

Chemical and Biochemical Engineering Faculty Research & Creative Works

Acetylene has been oxidized anodically in aqueous solutions at 80 °C on gold electrodes. It was found that the partial oxidation to CO₂ was accompanied by a polymer formation. Effects of potential, acetylene partial pressure, pH, and temperature on the rate (current) were measured. A discontinuity in the Tafel curves was noted that indicated a change in the reaction mechanism with potential. The discontinuity was also pH dependent. A mechanism involving the discharge of H₂O and/or OH− has been proposed that is consistent with the experimental results. © 1967, The Electrochemical Society, Inc. All rights reserved.

The Role Of The Doctor Of Engineering Degree In Graduate Education, Wouter Bosch, Robert E. Carlile

Chemistry Faculty Research & Creative Works

No abstract provided.