Digital Commons Network^™

A Study Of The Dynamics Of Gas Adsorption In An Air Fluidized Bed, William Charles Zalewski

Dissertations

The dynamics of gas adsorption was studied in an air fluidized bed containing activated alumina particles. The adsorption studies made with a fixed bed and in the transition region between minimum fluidization velocity and 2.0 times minimum fluidization velocity, compliment work done at higher velocities. With adsorption, particle motion controlled the overall dynamics of the fluidized bed. A different approach in applying the two phase fluidization model was necessary to satisfactorily describe unsteady state adsorption in fluidized beds. Experimental and theoretical results were compared in frequency response plots to obtain a rigorous comparison. Good agreement was obtained for flow rates …

Correlation And Prediction Of Diffussion Coefficients In Binary Gas Systems, Raymond Gerald Bailey

Theses

A correlation was developed for estimating binary gas diffusion coefficients by the reference substance method, in this case using the viscosity of air and subsequently its corresponding temperature. The derivation was made by the linear least square analysis of 65 different binary systems comprising 161 separate data points at temperatures ranging from 193°K. to 1200°K. At any given temperature only the critical molal volume and the molecular weights of the two gases of interest are required to calculate the diffusion coefficient. The correlation based on the viscosity of air had an average error of 7.67%. The correlation using temperature had …

The Absorption Of Hydrogen Chloride From Dilute Air Mixtures, Edgar L. Demarest

Theses

A study was made of the absorption of hydrogen chloride from air mixtures containing from 1 to 40 mgm. HCl/liter (1000 to 40000 mgm./m.³), using a.4" diameter tower packed with 2" Intalox saddles, irrigated with water or with sodium hydroxide solutions of 0.3% to 3.8% concen?tration. Gas flow rates of 177 to 752 lbs./(hr.)(ft.²) were investigated at three liquid rates: 2960 ; 4260, and 5700 lbs./(hr/)(ft.²). All data were collected below the flooding point.

Correlations of the height of a transfer unit with the superficial gas velocity were prepared for water and for sodium …

Aiir Pollution Emissions From Turbine Powered Aircraft, Raymond Arthur Filippini

Theses

The major pollutants that are emitted by jet aircraft include: particulate matter (soot), carbon monoxide, aldehydes, hydrocarbons, and nitrogen oxides. The first of the pollutants, particulate matter (smoke), constitutes not only a visual nuisance but is also a potential health problem. The rest, which are not visible, are irritants and in high enough concentrations can be toxic.

Since pollutants emitted by jet aircraft are of the same type as those given off by a car, a direct comparison is possible. In one landing take off cycle (LTO), a four engine jet aircraft emits the same amount of particulate matter as …

A Computer Program For The Design Of Packed Extraction Columns, George P. Gaccione

Theses

A computer program for the design of packed extraction columns has been developed. This program can operate with a minimum of data of the type that can easily be determined or estimated. The program can be used to investigate design alternates during the preparation of project cost estimates and for the final design of extraction columns.

Viscoelastic Properties Of Polymer Melts, Wu-Shiong Lee

Theses

Thirteen samples of molten polymers were used to test Spriggs and Careau Models. Two empirical equations, one for apparent viscosity and the other which is new, for primary normal stress difference, were checked with these samples also.

In order to test the models, material functions were sought for some specific flow patterns under which the experimental data were collected, and then these functions were compared with data.

Careau Model was found to be better than Spriggs Model in representing molten polymer properties but still yield large deviations. Two empirical equations fitted data quite well and were expected to be useful …

Combined Feedforward-Feedback Control Of A Fluidized-Bed Reactor, Reginald Eugene Mitchell

Theses

Feedforward control, feedback control, and combined feedforward-feedback control were studied on an analog computer to evaluate their effectiveness in controlling a fluidized-bed reactor used for the decomposition of cumene. Proportional, proportional-integral, proportional-derivative, and proportional-integral-derivative modes of control were investigated. Step changes in set-point and load were used as disturbances. The Ziegler-Nichols method and the process reaction curve method of Cohen and Coon were compared in determining values of KC, Ti, and Td which gave optimum control of the fluidized-bed reactor.

Control equation were obtained from the block diagrams of the systems and solved on an EAI TR-20 Analog Computer.

It …

A Digital Computer Simulation Of A Batch Or Semi-Batch Reactor, Robert Edward Viczorek

Theses

A digital computer simulation of a batch or semi-batch reaction was developed. The system consisted of a jacketed, agitated vessel equipped with a temperature controller modulating a control valve in the stream to the jacket. The reaction was liquid phase, and the jacket medium was liquid.

The program was written in a general form so as to be applicable to any liquid phase reaction with minimum modification.

A numerical technique was employed using initial values of the process variables in the first cycle of calculations for a time interval, and then using average values for further iterations. The simulation proceeded …

Heat And Mass Transfer In The Lyophilizatiuon Of Pharmaceuticals In Vials By Conduction Heating, William Warren Walsh

Theses

This thesis investigates the lyophilization of pharmaceuticals in vials by conductive heat transfer. The process phase diagram and methods of determining the solution eutectic temperature are reviewed. The theoretical considerations of heat and mass transfer pertaining to this process are discussed.

Lyophilization tests of distilled water and of mannitol solutions are used to indicate the relationship between vacuum chamber total pressure and the product/vial interface temperature. Experiments with 10% lactose solutions are used to determine the effect of shelf fluid temperature, product height and chamber vacuum on product/vial interface temperature. Test on a pharmaceutical product are used to confirm the …

The Relation Of Heat Transfer To Power Consumption Of Liquids In Turbulent Flow, John D. Bien

Theses

The relationship between the heat transfer ability and the power input requirement of liquid coolants in a turbulent heat transfer condition was investigated. A correlation in terms of the liquid physical properties and the required volumetric flow was proposed and the use of this correlation in selection of liquids as coolant was discussed. The optimum condition for a high heat transfer/power input ratio was also discussed.

Phosphate Removal From Sewage Using A Combination Of Ferric Chloride And A Polymeric Flocculant, Ravindra C. Patel

Theses

The present work is concerned with a newer technique and approach to the problem of phosphate removal from waste water. This includes the removal of phosphate from the sample of activated sludge, i.e., a sample from the aeration tank of the secondary sewage treatment. The phosphate is removed by using ferric chloride as a precipitating agent and a cationic polyelectrolyte (P.E.) as a flocculating agent. Results of this study showed that: (a) P.E. addition gives a significant improvement in phosphate removal over that obtained by ferric chloride alone. In some cases the phosphate removal increased from 92 to 96.5 per …

The Transferability Of Force Constants Among Olefins, John Martin Comerford

Theses

A normal coordinate analysis of the in-plane vibrations of ethylene was performed using a modified valence force field, a modified Urey-Bradley force field and a hybrid orbital force field. The B_2u species of isobutene was also analyzed. An attempt was made to transfer force constants from ethylene and thereby solve the A₁ species of isobutene, but a solution could not be obtained. This suggests that simple transference of force constants is not feasable in this case.

The potential energy distributions obtained for ethylene are discussed. The normal coordinates calculated in this work are appended.

A Modified Redlich-Kwong Equation For Nonpolar And Slightly Polar Gases, David G. Skamenca

Theses

The PVT prediction capability of the Redlich-Kwong equation is substantially improved through the use of a generalized correlation based on the acentric factor. No experimental data is required to obtain the improved constants. Only the acentric factor and the critical properties of the pure gas are needed. The correlation of improved constants is limited to non-polar and slightly polar pure gases and mixtures in the supercritical temperature range.

The correlation applies to a reduced temperature range 1.00 le; T_R le; 1.60 and a reduced pressure range of 0.030 le; P_R le; 3.00. The correlation reduces deviations by as …

A Simplification Heuristic For Large Flow Tables, R. J. Smith, James H. Tracey

Electrical and Computer Engineering Faculty Research & Creative Works

Flow tables specifying large asynchronous sequential circuits often contain more internal states than are required to specify desired circuit behavior. Known minimization techniques appear unsuited for reduction of such large (rows X columns > 250) flow tables, because of excessive computation and intermediate data requirements for problems of this size. The algorithm described here is intended to rapidly produce a simplified-but in general non-minimal-flow table. It is most economical when applied to extremely large tables and was devised primarily for automated design applications. The procedure has been programmed in PL/1 and has been incorporated into an asynchronous sequential circuit design automation …

Production Attachment For Wood Turning, Julian A. Olson

Graduate Research Papers

As an industrial arts instructor for the short period of three years the writer has recognized a definite shortcoming in his instruction of the woodworking lathe. Instruction related to the woodworking lathe by the conventional "hand tool" methods is most important in leading to the students' understanding of basic turning ideas. This instruction, however, falls short of providing an up-to-date picture of the woodworking lathes used by industry.

As a means of overcoming this problem, the writer undertook the study of lathes as a project for the course, "Projects in Industrial Arts". This research provided information necessary in the construction …

Plastics: Mold Design And Fabrication, Duane H. Rippe

Graduate Research Papers

Students have often asked if additional molds were available which would make different objects other than golf tees. Literature provided with the injection molder described several methods of mold construction which could be fabricated in the school shop. The writer considered the possibility of making another mold, however, a time factor and limited experience prohibited construction.

The problem seemed to be appropriate for the Projects Course 33:270 at the University of Northern Iowa. The course and research involved would assimilate the needed information to construct a mold and to teach plastic injection mold construction more effectively.

The Microstructure Of Hardened Gypsum Pastes, Raafat Ishak Abdel Malek

Archived Theses and Dissertations

No abstract provided.

Temperature Protection For Fruit Trees By Air-Supported Plastic Structures, Ram T. Gadhavi

Theses and Dissertations

The greatest weather enemy in all fruit destruction is the late spring frost which moves across the country under the high pressure areas that are occasionally seen on the weather maps, and kills the fruit buds.

Traps And Trap Distribution In Commercial Zinc Sulphides Phosphors Silver Activated And Poisoned With Cobalt, Zohra Safinaz El Calamawy

Archived Theses and Dissertations

No abstract provided.

Switching Characteristics Of Calcium Borate Glasses Containing Iron, Mahmoud Aly El Hamamsy

Archived Theses and Dissertations

No abstract provided.

A Comparative Study Of The Inorganic Composition In Body Fluids Of Four Egyptian Tick Species, Samir Fouad Araman

Archived Theses and Dissertations

No abstract provided.

Particle Dynamics In The Mixing Of A Particle-Laden Stream With A Secondary Stream In A Duct, William Doyle Cranney

Theses and Dissertations

The purpose of this thesis is to review the history and discuss the present work being done in particle-gas flow, with application to air- augmentation of a particle-carrying, fuel-rich gas jet. A drawing of the model considered is shown in Figure 1, with the area of interest labeled. The thesis is intended as a thorough literature review and analysis.

Determination Of Effective Strain For The Strainhardening Of Aluminum Subjected To Completely Reversed Strain Combinations, Navin M. Patani

Theses and Dissertations

It is known that subrecrystallization plastic deformation increases the strength of a metal. The amount of strengthening that may be acquired can be approximated using a strainhardening equation and a simple given strain. The purpose of this thesis was to determine the effective strain for predicting strainhardening for annealed aluminum subjected to completely reversed strain combinations.

A Survey Of Literature On The Pyrolysis Of Wood And Other Cellulosic Solids, Kenneth P. Sasine

Theses and Dissertations

The study of the ignition of wood and other cellulosic materials has resulted in the publication of a large amount of literature. As an aid in the planning and interpretation of future research, it was felt that a survey of a representative body of literature should be made. With this as its motivation, the present work was initiated.

Triaxial Stress Effects In Weldments Associated With The Heat Affected Zone, Rohit A. Mehta

Theses and Dissertations

The welding of steel occupies an important place as a major fabricating process in industry. The welding of steel has been a subject of research for many years, and much information has been obtained about the strength of weldments.

Wood Flour Molding, Charles Reed Snyder

Graduate Research Papers

The purposes of this research are briefly stated in the following:

1. Develop an understanding of the values of an industrial process through the use of raw materials and laboratory equipment.

2. Investigate wood flour molding and its relation to industry.

3. Experiment with materials, laboratory equipment, and wood flour mixtures to produce a molded article.

4. Develop an instructional unit for use in an industrial arts curriculum.

A Feasibility Study Of The Application Of Bondgraph Modeling And Computerized Nonlinear Model Parameter Identification Techniques To The Cardiovascular System, Randall L. Taylor

Theses and Dissertations

Recent years have witnessed an increasing trend for people in the medical and engineering professions to couple their talents in a more united effort to better understand the functioning of the human body. This union of technologies has meant the introduction of new viewpoints and techniques in the field of physiological research. The engineers' basic tool, mathematical modeling, has perhaps been one of the most noticeable additions. There has been a significant amount of work done in recent years along these lines of deriving mathematical models to express the functioning of a subsystem of the body, and then, using analog, …

An Investigation Of A Computer Technique For Determining The Characteristic Parameters Of A Viscoelastic Model With Hysteresis Effects From Transient Experimental Data, Stephen Jack Clark

Theses and Dissertations

The object of this work was to develop a computer technique for determining the characteristic parameters of spring-mass system with hysteresis effects from transient experimental data. The technique was intended to be utilized to determine the parameters of models of systems where complex geometry and rate dependent properties would make a determination of the model parameters most difficult, and where the parameters typically obtained from static test would not characterize the rate dependent properties accurately.

Non-Linear Analysis Of Electrocardiogram Tracings In Detection Of Occult Coronary Artery Disease, Joseph Robert Levitt

Dissertations

The general problem of identifying significant characteristics of a system by analyzing the properties of a signal emitted by that system is common to many disciplines, biological as well as physical. In general, achievement of a satisfactory solution depends on the capability of assigning membership of candidate signals to one of a number of mutually exclusive categories:

In this study, a new technique of processing the standard electrocardiograms from human subjects has been developed. This technique employs a set of non-linear transformations which enable the assignment of electrocardiograms into one of two Mutually exclusive categories. The first category is that …

Extension And Application Of The Sedov-Berdichevskii Variational Principle, Francis X. Prendergast

Dissertations

The Sedov-Berdichevskii variational principle is extended, and this extended principle is employed in the construction of a shell theory.

The extension of the principle is accomplished by the use of Lagrangian multipliers, and a redefinition of terms in order to maintain the original generality of the principle. The Euler equations of the extended variational principle provide, in addition to those obtained in the original principle, elastic and plastic kinematic relations, and, elastic and plastic constitutive relations. Also, the Euler equations of the original principle are obtained in a physically more meaningful form. Examples are given which show how this principle …