Digital Commons Network^™

A Comparison Of Computer Codes For Fast Neutron Dosimetry By The Foil Technique, Jau Wen Chen

Masters Theses

"A comparison of the major codes currently used for fast neutron dosimetry based on the foil technique has been made. These codes are SAND II, SPECTRA and RDMM. The comparison is based upon the deviation of calculated from-measured activities, the input data decks, the obtained information, and the computer time required. Four sets of data were used to be compared upon the above four viewpoints, the conclusion reached is that the SPECTRA computer code is the most satisfactory for the UMR Reactor fast neutron spectrum"--Abstract, page ii.

The Design And Experimental Investigation Of A Hybrid Phase-Lock Loop, Srinivasa H. R. Raghavan

Masters Theses

"This thesis describes the design and the laboratory implementation of a hybrid phase-lock loopage The step-by-step procedure followed in developing this experimental hybrid phase-lock loop, and its optimization with respect to various parameters are given. In regard to the performance characteristics, the loop was used to obtain the phase estimate of a split-phase modulated signal. The phase error probability density function was measured under various input noise conditions and these results are included and compared with previously published theoretical results"--Abstract, page ii.

Design And Preliminary Testing Of A Thermomechanical Rock Fragmentation Apparatus, Gary Earl Fenton

Masters Theses

"The design characteristics of equipment to thermally weaken and mechanically fragment hard rock were developed and the apparatus constructed. An initial investigation of thermo-mechanical fragmentation was conducted on Missouri red granite. The particles from the fragmentation tests were sized and this analysis was used in the Rittinger theory to calculate surface area breakage energy. It was found that the application of thermal energy could reduce the surface area breakage energy per unit volume of material removed by as much as 41 percent. The use of kerfs in the rock increased the amount of material removed and permitted larger particles to …

Characteristics Of And Suggested Improvements In Communication Laboratory Equipment At University Of Missouri-Rolla, William Edgar Abernathie

Masters Theses

"This paper documents characteristics of and suggests improvements in Communication Laboratory Equipment built at the University of Missouri at Rolla. Included are Voltage Controlled Oscillators, Discriminators, Operational Amplifiers, and Multipliers. The graduate and undergraduate laboratory student thus has available equipment characteristics and, when building higher performance equipment, improvement suggestions"--Abstract, page ii.

The Pm3m-Fm3m Transformation And Phase Equilibrium In Solid Solutions Of Csc1 With Kc1, Rbc1, And Csbr, John David Weyand

Masters Theses

"Thermal expansion and the Pm3m t Fm3m transition of cesium chloride have been studied with high temperature diffractometry, differential thermal analysis, and heating and quenching techniques. The onset temperature of the transition in pure CsCl, on heating, is 471ºC. There are no observable premonitory effects below the transition temperature and no apparent structural relationships between the polymorphs is apparent. Both phases coexist over a 20º to 50ºC temperature range and equilibrium thermal hysteresis occurs on heating and cooling. Hysteresis behavior is explained by addition of strain energy parameters to the free energy function. Initiation of the Pm3m t Fm3m transformation …

Transient Hydraulic Simulation: Breached Earth Dams, D. L. Fread

Doctoral Dissertations

"A conceptual method to alleviate flood damages due to over-topping failures of small earthfill dams is the incorporation of a relatively thin erosion retarding layer within the dam. This paper investigates the reduction in the reservoir release due to the hypothetical erosion retarding layer. In addition, the paper provides a method for the determination of an optimal location of the layer so as to minimize the maximum possible reservoir release due to a gradually breached earth dam. The transient reservoir flow is simulated by a numerical model, based upon the solution of the one-dimensional St. Venant unsteady open-channel flow equations. …

X-Ray And Neutron Diffraction Study Of The Holmium-Iron System, Michael Fred Simmons

Doctoral Dissertations

"Neutron diffraction and x-ray powder studies have been made of holmium-iron intermetallic compounds. The magnetic moments of Ho and Fe are in good agreement with measured spontaneous magnetization assuming a ferrimagnetic model with the Ho moments antiparallel to the Fe moments. The magnetic moments of the Fe atoms are found to be localized and thus independent of the rare earth content in the alloys. In contrast to HoCo₃, (00ℓ) type magnetic peaks in the neutron diffraction patterns are still prevalent at room temperature and gradually decrease as the Curie temperature is approached. This fact indicates that the easy direction of …

The Effect Of Channel Errors In The Differential Pulse-Code-Modulation Transmission Of Sampled Imagery, Roger J. Arguello, Harvey R. Sellner, John A. Stuller

Electrical and Computer Engineering Faculty Research & Creative Works

This Paper Presents an Analysis, Simulation, and Discussion of the Effects of Communication Errors on Four-Bit Differential Pulse-Code Modulation (DPCM) Sampled Imagery. Simulations Are Presented that Describe the Effects of Inserting Periodic "PCM Updates" in Order to Correct Communication Errors in the DPCM Transmission of Photographic Scenes that Have Been Scanned and Sampled at the Nyquist Rate. Copyright © 1971 by the Institute of Electrical and Electronics Engineers, Inc.

Test 1073: John Deere 4620 Syncro Range, Nebraska Tractor Test Lab

Nebraska Tractor Tests

No abstract provided.

Test 1064: John Deere 4620 Power Shift, Nebraska Tractor Test Lab

Nebraska Tractor Tests

No abstract provided.

Test 1063: John Deere 7020, Nebraska Tractor Test Lab

Nebraska Tractor Tests

No abstract provided.

Test 1085: John Deere 2030/John Deere 2440, Nebraska Tractor Test Lab

Nebraska Tractor Tests

No abstract provided.

Test 1065: Allis-Chalmers Landhandler 210 Diesel, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF TEST REPORT

GENERAL CONDITIONS

East tractor is a production model equipped for common usage. Power consuming accessories can be disconnected only when it is convenient for the operator to do so in practice. Additional weight can be added as ballast if the manufacturer regularly supplies it for sale. The static tire loads and the inflation pressures muse conform to recommendations in the Tire Standards published by the Society of Automotive Engineers.

PREPARATION FOR PERFORMANCE RUNS

The engine crank case is drained and refilled with a measured amount of new oil conforming to specifications in the operator’s manual. The …

Test 1067: Case 1070 And 1090 Manual Diesel, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF TEST REPORT

GENERAL CONDITIONS

East tractor is a production model equipped for common usage. Power consuming accessories can be disconnected only when it is convenient for the operator to do so in practice. Additional weight can be added as ballast if the manufacturer regularly supplies it for sale. The static tire loads and the inflation pressures muse conform to recommendations in the Tire Standards published by the Society of Automotive Engineers.

PREPARATION FOR PERFORMANCE RUNS

The engine crank case is drained and refilled with a measured amount of new oil conforming to specifications in the operator’s manual. The …

Test 1066: Case 1070 And 1090 Power Shift Diesel, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF TEST REPORT

GENERAL CONDITIONS

East tractor is a production model equipped for common usage. Power consuming accessories can be disconnected only when it is convenient for the operator to do so in practice. Additional weight can be added as ballast if the manufacturer regularly supplies it for sale. The static tire loads and the inflation pressures muse conform to recommendations in the Tire Standards published by the Society of Automotive Engineers.

PREPARATION FOR PERFORMANCE RUNS

The engine crank case is drained and refilled with a measured amount of new oil conforming to specifications in the operator’s manual. The …

Test 1072: Kubota L-260 Diesel 8-Speed, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF TEST REPORT

GENERAL CONDITIONS

East tractor is a production model equipped for common usage. Power consuming accessories can be disconnected only when it is convenient for the operator to do so in practice. Additional weight can be added as ballast if the manufacturer regularly supplies it for sale. The static tire loads and the inflation pressures muse conform to recommendations in the Tire Standards published by the Society of Automotive Engineers.

PREPARATION FOR PERFORMANCE RUNS

The engine crank case is drained and refilled with a measured amount of new oil conforming to specifications in the operator’s manual. The …

Test 1075: Deutz 4006 Diesel, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF TEST REPORT

GENERAL CONDITIONS

East tractor is a production model equipped for common usage. Power consuming accessories can be disconnected only when it is convenient for the operator to do so in practice. Additional weight can be added as ballast if the manufacturer regularly supplies it for sale. The static tire loads and the inflation pressures muse conform to recommendations in the Tire Standards published by the Society of Automotive Engineers.

PREPARATION FOR PERFORMANCE RUNS

The engine crank case is drained and refilled with a measured amount of new oil conforming to specifications in the operator’s manual. The …

Test 1074: Deutz 8006 Diesel, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF TEST REPORT

GENERAL CONDITIONS

East tractor is a production model equipped for common usage. Power consuming accessories can be disconnected only when it is convenient for the operator to do so in practice. Additional weight can be added as ballast if the manufacturer regularly supplies it for sale. The static tire loads and the inflation pressures muse conform to recommendations in the Tire Standards published by the Society of Automotive Engineers.

PREPARATION FOR PERFORMANCE RUNS

The engine crank case is drained and refilled with a measured amount of new oil conforming to specifications in the operator’s manual. The …

Test 1077: Case 870 Manual Diesel, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF TEST REPORT

GENERAL CONDITIONS

East tractor is a production model equipped for common usage. Power consuming accessories can be disconnected only when it is convenient for the operator to do so in practice. Additional weight can be added as ballast if the manufacturer regularly supplies it for sale. The static tire loads and the inflation pressures muse conform to recommendations in the Tire Standards published by the Society of Automotive Engineers.

PREPARATION FOR PERFORMANCE RUNS

The engine crank case is drained and refilled with a measured amount of new oil conforming to specifications in the operator’s manual. The …

Test 1083: International Farmall 1066 Hydrostatic Turbo Diesel, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF TEST REPORT

GENERAL CONDITIONS

East tractor is a production model equipped for common usage. Power consuming accessories can be disconnected only when it is convenient for the operator to do so in practice. Additional weight can be added as ballast if the manufacturer regularly supplies it for sale. The static tire loads and the inflation pressures muse conform to recommendations in the Tire Standards published by the Society of Automotive Engineers.

PREPARATION FOR PERFORMANCE RUNS

The engine crank case is drained and refilled with a measured amount of new oil conforming to specifications in the operator’s manual. The …

Test 1082: International Farmall 966 Diesel, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF TEST REPORT

GENERAL CONDITIONS

East tractor is a production model equipped for common usage. Power consuming accessories can be disconnected only when it is convenient for the operator to do so in practice. Additional weight can be added as ballast if the manufacturer regularly supplies it for sale. The static tire loads and the inflation pressures muse conform to recommendations in the Tire Standards published by the Society of Automotive Engineers.

PREPARATION FOR PERFORMANCE RUNS

The engine crank case is drained and refilled with a measured amount of new oil conforming to specifications in the operator’s manual. The …

Test 1087: Massey-Ferguson Mf 1800 Diesel, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF TEST REPORT

GENERAL CONDITIONS

East tractor is a production model equipped for common usage. Power consuming accessories can be disconnected only when it is convenient for the operator to do so in practice. Additional weight can be added as ballast if the manufacturer regularly supplies it for sale. The static tire loads and the inflation pressures muse conform to recommendations in the Tire Standards published by the Society of Automotive Engineers.

PREPARATION FOR PERFORMANCE RUNS

The engine crank case is drained and refilled with a measured amount of new oil conforming to specifications in the operator’s manual. The …

Test 1089: Case 770 Power Shift Diesel 12-Speed (Chassis S/N 8675001 And Up), Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF TEST REPORT

GENERAL CONDITIONS

East tractor is a production model equipped for common usage. Power consuming accessories can be disconnected only when it is convenient for the operator to do so in practice. Additional weight can be added as ballast if the manufacturer regularly supplies it for sale. The static tire loads and the inflation pressures muse conform to recommendations in the Tire Standards published by the Society of Automotive Engineers.

PREPARATION FOR PERFORMANCE RUNS

The engine crank case is drained and refilled with a measured amount of new oil conforming to specifications in the operator’s manual. The …

The Axial Contact Of Finite Elastic Cylinders With Application To Thermal Contact Resistance, Ross Orlo Mcnary

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Predictions of the macroscopic thermal contact resistance have been severely restricted because the macroscopic contact area between finite members could not be determined. A new method of solution to this contact problem in elasticity is developed which is applicable to a wide variety of geometries and boundary conditions. A physical lumped-parameter model is employed from which the finite difference equations in terms of displacement are derived. Calculations using this method indicate that large errors in the prediction of the thermal contact resistance can result if solutions for bodies of infinite extent are employed for finite regions of interest. Especially large …

Liquid Viscosity Measurement Using A Buret: An Instructional Technique, Charles A. Sorrell

Materials Science and Engineering Faculty Research & Creative Works

No abstract provided.

Activation Volumes Of Interstitial Diffusion In Ferromagnetic Metals And Alloys, Manfred Wuttig, J. Keiser

Materials Science and Engineering Faculty Research & Creative Works

The Dis accommodation technique was used to determine the activation volumes of carbon diffusion ΔV of a Fe-1.4 wt% Si alloy, of hcp cobalt, and of nickel at the temperatures of -21, 75, and 110°C, respectively. The obtained values of ΔV are +0.3 ± 0.3 and -0.6 ± 0.9 cm3 mole-1 for the two relaxations observed in hcp cobalt, and 1.2 ± 0.1 cm3 mole-1 for nickel. These results are discussed in terms of a continuum model that interprets the activation energy of diffusion as a sum of the strain and exchange energies. It is found that in ferromagnetic solids …

Preparation Of Metallic Oxide Aerosols By Vaporization And Degradation Of Organic Compounds, Tom B. Larsen

Chemical and Biological Engineering ETDs

Simple, dependable methods for the generation of aerosols are necessary to many forms of research. Specifically inhal­ation research has a requirement for sub-micron sized insoluble particles.

Two different methods for the production of oxide aerosols from vaporizable compounds were tried. The first method, a mod­ification of the Rapaport-Weinstock generator (R3), consisted of nebulization of a solution into a droplet mist. Next the drop­lets were vaporized, and condensation nuclei formed from the nonvaporizable impurities in the solution. The vapor was allowed to condense on the nuclei in a relatively large chamber, then the resulting liquid droplet aerosol was dried and converted …

An Experimental Study On Heat Transfer Coefficient For Carbon Laden Gas, Jacob Chi-Kwong Huang

Chemical and Biological Engineering ETDs

Abstract

A complete carbon black pilot plant was employed in this study. Carbon laden gas was produced in a fur­nace and introduced into the outer pipe of a heat ex­changer. Air, at the same time, was introduced into

the inner pipe of the heat exchanger cocurrently with the carbon laden gas. Thus, heat, with temperature dif­ference as driving force, would transfer from the car­bon laden gas to the air stream. The temperatures along the two streams were measured by iron-constantan ther­mal couples and recorded by a multi-reading temperature

recorder. Air supply and fuel (C3H8) supply were intro­duced into the furnace …

Industry Participation In Electrical Engineering Education-Extra High Voltage Laboratory, J. Derald Morgan

Electrical and Computer Engineering Faculty Research & Creative Works

A unique electrical engineering laboratory course is described. This laboratory is an example of how industry can cooperate with universities in engineering education. The organization and operation of the course as well as the course material is outlined and explained, including the ways in which the industry participates in the operation of the laboratory. The educational benefits derived from such a cooperation between industry and the university are briefly detailed. These benefits are extended to the student, the University, the faculty, and the participating industry. This article provides the framework on which other laboratory experiences could be conceived and developed …

Empirical Bayesian Learning, David R. Cunningham, Arthur M. Breipohl

Electrical and Computer Engineering Faculty Research & Creative Works

It is shown that a certain weighted average of the prior distribution and the empirical distribution yields an estimate of the posterior distribution that is consistent with Bayes' theorem. Acomparison of this approach and conventional parametric Bayesian estimation is made for some specific cases. Copyright © 1971 by The Institute of Electrical and Electronics Engineers, Inc.