Digital Commons Network^™

Accidents On Rural Interstate And Parkway Roads And Their Relation To Pavement Friction, Rolands L. Rizenbergs, James L. Burchett, Cass T. Napier

Kentucky Transportation Center Research Report

Friction measurements were made with a skid trailer at 70 mph (31 m/s) on 770 miles (1240 km) of rural, four-lane, controlled-access routes on the interstate and parkway systems in Kentucky. Each construction project was treated as a test section. Accident experience, friction measurements, and traffic volumes were obtained for each. Various relationships between wet-weather accidents and skid resistance were analyzed. The expression of accident occurrence which correlated best with skid and slip resistance was wet-weather accidents per 100 million vehicle miles. Accidents increased greatly as Skid Numbers (70 mph or 31 m/s) decreased from 27 ± 1. Analysis of …

Gaussian Light Beams In Inhomogeneous Media, Lee W. Casperson

Electrical and Computer Engineering Faculty Publications and Presentations

Vector wave solutions are obtained for the propagation of beams of light in media having slow spatial variations of the gain, loss, or index of refraction. The formalism developed here is applicable to a wide range of problems, and an exa mple considered in detail is the propagation of off-axis beams in lenslike laser materials and optical waveguides. A procedure is also described for the diagnosis of localized dielectric inhomogeneities such as plasmas by means of Gaussian laser beams.

Biocatalytic Oxidation Of Nitrilotriacetate, Saul Hammerman

Theses

The specific scope of this work is to study the biological and chemical effects of a single genetic strain of bacteria, Bacillus subtilis #9524, on the specific destruction to innocuous products of sodium nitrilotriacetate (NTA) and sodium tripolyphosphate (STPP). Insofar as the same strain of bacteria was used each time, under limited variability and sterile conditions, the side effects of multiple bacterial strains and their inter-relationships among themselves and the organic substrates are eliminated. This has allowed for excellent replication of results.

This is a generalized technique for the evaluation of the biodegradability of a compound. Whereas tests with activated …

Correlation Of Drain Breakdown With Excess Noise And Other Surface-Related Phenomena In Enhancement Mosfets, Jerry J. Rij

Theses

An investigation of semiconductor surface-related phenomena has been undertaken to correlate 1/F noise with drain breakdown in P-channel enhancement MOSFET's. Increases in the intensity of drain current fluctuations at 10Hz and at 1KHz, particularly at the higher frequency, was observed following accelerated life-testing for threshold voltage drift. It was also concluded that mobile ions near the oxide-semiconductor interface produce a sharp increase in fast trapping centers. It was also found that 1/F noise intensity consistently peaked at the threshold of drain breakdown and that it steadily decreased with further increases in drain current. Of all the transistors tested, those with …

Rubbery Acrylic Polymer Adhesives, Steven Walter

Theses

This study shows how rubbery acrylic polymer adhesives can be used to adhere rubber substrates to each other. Two substrate rubber compounds were used. A styrene-butadiene copolymer and a styrene-acrylonitrile copolymer. The adhesives were homopolymers based on polybutyl acrylate and poly2-ethyl hexyl acrylate.

Two reference standards were used. The first was commercial rubber based, solvent cements. The second was commercial acrylic solution polymers. All experimental work was compared to these standards. An attempt was made to optimize the adhesive components, as well as the adhesive application procedures and curing conditions.

A primer coating consisting of polymer, monomer, and catalyst was …

Non-Transposing Mute, Benjamin R. Gossick, Karl A. Schneider

Electrical and Computer Engineering Faculty Patents

A non-transposing mute having a metallic hemispherical resonator with a hollow acoustic filter attached thereto is provided for detachably fitting upon the rim of a brass musical instrument. A variety of tonal quality is available by choice of the particular filter selected by the musician.

Memory Utilization For A Dynamically Microprogrammed Computer, Paul D. Stigall

Electrical and Computer Engineering Faculty Research & Creative Works

A Particular, Dynamically Microprogrammed Computer (Proposed by Tucker and Flynn in Commun. of ACM, April 1971) is Considered with Respect to Main Memory and Micro-Memory Utilization. a Dependency is Shown between Memory Utilization and Utilization of the Arithmetic and Logic Unit.

Minimum Cost Design Of Water Distribution Systems, Don J. Wood, C. O. Charles

KWRRI Research Reports

The objective of this study was to develop the analytical tools and procedures for minimum cost design of water distribution systems. Both analog and digital means of carrying out pressure and flow calculations were developed. As a result of this effort, digital programs for pressure and flow calculations in water distribution systems were written and have been widely distributed to practicing engineers. One procedure is based on a direct solution of the basic system equations using a linearization scheme and has several advantages over conventional techniques such as the Hardy Cross method. These include avoiding the need to initially balance …

In Situ Shear Strength Parameters By Dutch Cone Penetration Tests, C. Thomas Gorman, Tommy C. Hopkins, Vincent P. Drnevich

Kentucky Transportation Center Research Report

Dutch cone penetration testing was performed and undisturbed samples were collected at four Kentucky highway sites. Shear strength, as determined by consolidated, undrained triaxial testing of the undisturbed samples, was correlated with friction resistance as measured by the Dutch friction cone. Statistical analysis of all data showed shear strength to be about 80 percent of friction resistance. Recommendations for the use of the Dutch cone penetration test in Kentucky soils were also made.

Design Guide For Bituminous Concrete Pavement Structures, James H. Havens, Robert C. Deen, Herbert F. Southgate

Kentucky Transportation Center Research Report

The proposed design guide includes procedures for estimating design EAL's, CBR, modulus of the asphaltic concrete, and an array of tables and graphs to determine pavement and layer thicknesses.

Stolvac: A Traffic Data System, Donald R. Herd

Kentucky Transportation Center Research Report

The purpose of this study was to design a traffic data inventory system and to develop operating procedures for that system. This report outlines the general design of such a system that will be called STOLVAC (acronym for Speed, Turning movements, Origin destination, Loadometer, Volume, Accident, and Classification data). The report also presents recommendations relating to the development and maintenance of STOLVAC. Staging of the system development is recommended.

Vehicle Noise Survey In Kentucky, Kenneth R. Agent, Rolands L. Rizenbergs

Kentucky Transportation Center Research Report

Individual noise measurements were obtained on 10,500 motor vehicles operating on Kentucky highways. The roadways were selected to represent varied geometric and environmental conditions and posted speed limits. Percentages of automobiles and trucks exceeding a given level of noise were determined. As expected, noise levels of trucks were significantly higher than for automobiles, and larger trucks produced higher noise levels than smaller trucks. For any vehicle type, noise increased with an increase in speed limit.

Recent Developments In The Use Of Precast Concrete Units For Buildings In The United States And Iran, Khosrow Ebadi Farshchi

Dissertations and Theses

The object of this study was to investigate the recent developments in the use of precast prestressed concrete members for buildings in the United States and Iran. In the United States, the study was concerned with developments in the usage of members such as slabs, wall panels, beams and columns. The latest technical and engineering reports, along with personal interviews, were used, and a number of case studies were conducted on recently built structures. The author also studied the newest developments in the precast concrete industry in Iran. A questionnaire was formulated in both Persian (native language of Iran) and …

15th Annual Rocky Mountain Spectroscopy Conference

Rocky Mountain Conference on Magnetic Resonance

Program and abstracts from the 15th annual meeting of the Rocky Mountain Spectroscopy Conference, sponsored by the Rocky Mountain Section of the Society for Applied Spectroscopy. Held in Denver, Colorado, August 20-21, 1973.

Symmetry-Forbidden Resonant Raman Scattering In Cu2O, S. P. S. Porto, P. F. Williams

P. F. (Paul Frazer) Williams Publications

We have observed resonant Raman scattering from the two longitudinal branches of the Raman-forbidden F_{1u modes of Cu2O. The agreement between our measured scattering cross section as a function of excitation frequency and a calculated cross section which assumes an intraband Frohlich electron-phonon interaction is good. This represents a quantitative confirmation of the resonant-Raman-scattering theory proposed by Martin.}

Buckling Of Diaphragm-Braced Columns Of Unsymmetrical Sections And Application To Wall Studs Design, Amir Simaan, George Winter, Teoman Peköz

CCFSS Library (1939 - present)

Lateral bracing has a significant effect on increasing the buckling load of compression members. In the case of wall stud construction, such bracing is provided by wallboards directly attached to the stud along its length and results in increasing the load carrying capacity significantly. The objective of this investigation is to study the behavior of singly symmetric sections braced by shear diaphragms and to apply the theoretical findings verified by experimental results to the design of wall studs. In the present investigation the shear rigidity as well as the rotational restraint of the diaphragm are considered. Using an energy approach, …

Buckling Of Diaphragm-Braced Columns Of Unsymmetrical Sections And Application To Wall Studs Design, Amir Simaan

CCFSS Library (1939 - present)

No abstract provided.

Stability Analysis Of Slide At Milepost 152.7, I 64, Carter County, Harry F. Girdler, Tommy C. Hopkins

Kentucky Transportation Center Research Report

A visual inspection of a slide near Milepost 153 on I 64 was made April 11, 1972, and reported in a memorandum prepared by B. H. Banks on April 12, 1972. The Division of Research made recommendations for correcting this situation in a memorandum to A. R. Romine on June 30, 1972. These recommendations were based on a limited field investigation and a stability analysis of a proposed berm to be located near Station 3483+00. In a letter dated August 18, 1972, Mr. A. J. Horner of FHWA requested borings be made at the site to establish rock depth and …

An Historical Review Of Oil Spills Along The Maine Coast 1953-1973, Edward H. Shenton

Maine Collection

An Historical Review of Oil Spills Along the Maine Coast 1953-1973

by Edward H. Shenton

Prepared for The Maine State Planning Office, Coastal Planning Group and The Research Institute of the Gulf of Maine (TRIGOM), August, 1973.

TRIGOM Publication No. 3

Contents: Introduction / A Chronology of Significant Oil Spills / A Summary of Biological Impacts / Spill Statistics / Discussion of Results / Conclusions of the Study / Recommendations for Future Research / Appendices

What Is An Airlifter?, Tim Brady

Publications

This article describes the components that make up the Tactical Air Command flight crew, from loadmaster, to flight engineer, to navigator, to copilot, and lastly, to pilot. All together, the crew work in coordination to deliver the goods or the troops. This article was Dr. Brady's last as editor of TAC Attack. Under his two-year leadership, the safety message continued to be heard.

Component Residential Building Construction, Gary L. Trickey

Graduate Research Papers

To study residential component building as one of the first steps towards a more industrialized method of home construction.

Explosive Electron Emission And The Characteristics Of High-Current Electron Flow, Robert Kelley Parker

Nuclear Engineering ETDs

Within the past several years, an increasing effort has been concen­trated on the application of high-current, relativistic electron beams to the problem of controlled thermonuclear fusion. Initially, this effort had been impeded by limitations in the high-voltage and pulsed-power technology required to develop pulsed, high-power electron accelerators. These technologies have been developed to a level where powers on the order of 10¹³ watts are now available for time durations of approximately 100 nanoseconds. With the initial limitations removed, the emphasis has more recently been centered on controlling and concentrating these beams to achieve the parameters necessary for fusion experimentation. …

A New Sampling Theorem For Causal (Non-Bandlimited) Functions., Alan Baker Campbell

Electrical and Computer Engineering ETDs

It is shown in this work that whereas any causal function (i.e., any function with a definite starting point) is non-bandlimited and thus would be thought to require an infinite sample rate, there is an infinite class of causal functions (identified as "regionally bandlimited functions" (r.b.f.'s)) for which a finite sample rate is adequate.

Fast Neutron Effects On Time Delay Occuring In Gallium Arsenide Laser Diodes., James Owen Schroeder

Electrical and Computer Engineering ETDs

A study has been made on the effects of fast neutron irradiation on time delay occurring in diffused GaAs laser diodes operating at 77° K and 300° K. Measurements were performed at 300° K prior to irradiation and thence after successive exposure to neutron irradiation to a maximum of about 1.2 x 10^14 nvt (>10 KeV). At 77° K, measurements were limited to a pre-irradiation characterization and a characterization after the final irradiation. A double acceptor model is used to account for the observed changes in the delay characteristics as a result of both temperature changes and neutron irradiation. …

An Experimental Study Of Ultrahigh Fluence Oxygen Ion Implantation In Silicon, Charles Burton Fite

Electrical and Computer Engineering ETDs

An investigation was made to determine the feasibility of using ultrahigh fluences of implanted oxygen ions to create a usable oxide layer on silicon for device applications. Previous studies have indicated that SiO₂ can indeed be formed in this manner, but very little work has been reported on the electrical and structural nature of the resulting oxide-silicon interface. Six implants with fluences ranging from 1.25 x 10¹⁷ to 1 x 10¹⁸ (O₂)⁺ /cm² were performed into p-type silicon wafers. The implanted material was then studied to determine how the variables of anneal time, …

Response Of Orthotropic Bridge Decks To Highway Loadings, Harry Morris Rexin

Dissertations and Theses

This thesis documents the fabrication, testing techniques, and response of a plastic scale model of an orthotropic bridge deck. To economically investigate a two-lane steel bridge deck, plastic Acrylic^R was used as a modeling material. Welds were simulated with dichloromethane, a capillary action solvent, and PS-30, a polymerizable cement. Deflections were measured with laboratory dial guages while strains were monitored with strain guages mounted on the deck.

The response of the deck to AASHO vehicle axle loads was compared with a discrete element computer program used to analyze orthotropic bridge decks continuous over flexible supports. Results indicate good correlation …

Problems Of Measurement In The Environmental Field, Harold M. Cota

Civil and Environmental Engineering

No abstract provided.

Generalized Feedback Shift Register Pseudorandom Number Algorithm, Theodore Gyle Lewis, W. H. Payne

Electrical and Computer Engineering Faculty Research & Creative Works

The generalized feedback shift register pseudorandom number algorithm has several advantages over all other pseudorandom number generators. These advantages are: (1) it produces multidimensional pseudorandom numbers; (2) it has an arbitrarily long period independent of the word size of the computer on which it is implemented; (3) it is faster than other pseudorandom number generators; (4) the "same" floating-point pseudorandom number sequence is obtained on any machine, that is, the high order mantissa bits of each pseudorandom number agree on all machines— examples are given for IBM 360, Sperry-Rand-Univac 1108, Control Data 6000, and Hewlett-Packard 2100 series computers; (5) it …

Process Control Of Activated Sludge Treatment, Richard I. Kermode, Robert W. J. Brett, Kenneth A. Debelak, John J. Davis

KWRRI Research Reports

General feed forward controllers, conforming to standard control modes, have been derived for an activated sludge process. The analysis indicated that the appropriate controllers are proportional control with measurement of substrate flow rate, and derivative control with measurement of inlet substrate concentration, and manipulation of the rate of return sludge by both controllers.

The performance of these controllers was tested by computer simulation of five dynamic aerator models with and without sludge storage, and with two settling basin models. In all cases significant reduction of the maximum exit substrate concentration was achieved. Additional improvement resulted from the use of sludge …

Bulletin - June, 1973, Civil Aviation Medical Association

Browse all Civil Aviation Medical Association Newsletters

A four page newsletter of the Civil Aviation Medical Association. The newsletter provided news about civil aviation medicine and information related to the organization.