Digital Commons Network^™

Speed Reduction In School Zones, Charles V. Zegeer, James H. Havens, Robert C. Deen

Kentucky Transportation Center Research Report

The use of flashing beacons together with signing has become somewhat standard throughout the country to alert drivers to the presence of school children and to regulate vehicle speed in school zones. Yellow beacons, usually two flashing alternately, may be used with both warning signs and regulatory signs. The only regulatory signs related to school zones are speed-limit signs. Both hazard identification beacons and speed-limit sign beacons are intended to operate only during hours when the warning and speed regulations are in effect. The effectiveness of signs and flashing lights in reducing speeds in school zones has been questioned.

The …

Modulated Generalized Ellipsometry, R. M.A. Azzam

Electrical Engineering Faculty Publications

We extend ellipsometry to the direct measurement of small perturbations of the Jones matrix of any linear nondepolarizing optical sample (system) subjected to a modulating stimulus such as temperature, stress, or electric or magnetic field. The methodology of this technique, to be called Modulated Generalized Ellipsometry (MGE), is presented. First an ellipsometer with arbitrary polarizing and analyzing optics is assumed, and subsequently the discussion is specialized to a conventional ellipsometer having either the polarizer-sample-analyzer (PSA) or the polarizer-compensator-sample-analyzer (PCSA) arrangement. MGE provides the tool for the systematic study of thermo-optical, piezo-optical, electro-optical, magneto-optical, and other allied effects for both isotropic …

Interpretation Of Tests On Welded Light Gage Steel Connections, Mark Shephard, George Winter, Teoman Peköz

CCFSS Library (1939 - present)

INTRODUCTION This report interprets the results of three sets of test data (Ref. 1 through 3) on welded light-gage cold-formed steel specimens. The tests were conducted at Cornell for the American Iron and Steel Institute on 252 symmetric puddle and fillet welded connections tested under monotonically increasing static load. The tested connections consisted of 130 shop welded specimens and 122 field welded specimens. All test connections had the same basic configuration being made up of center plates, referred to as parent plates or connected plates in the references, butted together with one or, in the case of the double sheet …

Bolted Connections In Cold-Formed Steel Structures, Randall L. Mosby, Wei-Wen Yu

CCFSS Library (1939 - present)

INTRODUCTION A. Purpose of Investigation. The design of bolted connections in cold-formed steel structures is based on the present AISI Specification for the Design of Cold-Formed Steel Structural Members. 1 Prior to the development of the design criteria, bolted connections were tested at University of Michigan 2 in the 1940's and then at Cornell University 3,4 in the 1950's. The present design provisions were developed primarily on the basis of the tests conducted by George Winter and his associates at Cornell University. Additional tests were recently made by Popowich 5 on multi-bolt connections and by Dhalla 6 on connections with …

Distributed Parameter Sensitivity Theory To Solve Certain Reliability Problems, Moses Nee Buernor Ayiku

Dissertations

It is well known that in actual control systems there are uncontrolled parameter changes caused by aging of elements, temperature, pressure and effects of externalmedium, among others, which may impair the performance ofthe system. Hence, there is the need to develop systems that weakly react to these parameter fluctuations. Sensitivity theory has been developed to study some of these problems. Most of the investigations in this area, however, deal with problems in continuous systems modeled by ordinary differential equations. Even the recent publications on sensitivity problems in distributed parameter control systems are largely concerned with systems modeled by first order …

Investigation And Optimum Design Of The Generalized Second-Order Phase-Locked Loop, William Allen Novick

Dissertations

In this dissertation, a second-order phase-locked loop (PLL) in which the loop filter contains complex zeros is investigated in both its linear and nonlinear modes of operation; prior designs used a filter containing a simple zero on the negative real axis. This "generalized" second-order PLL had been heretofore essentially unexplored.

The basic characteristics of the generalized second-order PLL operating in the linear mode including the open and closed-loop responses and the corresponding root locus were generated and compared against those of the conventional second-order PLL. As in the conventional case, the generalized second-order PLL is found to be unconditionally stable. …

Preparation And Magnetic Properties Of Rare Earth Garnets And Apatites, Rostam Mondegarian

Dissertations

It has been found possible to prepare garnets with magnetic trivalent rare earth ions filling all or most dodecahedral sites while nonmagnetic Sc³⁺ ions fill all octahedral sites and magnetic Fe³⁺ ions fill all or most tetrahedral sites. Phase-pure garnets found include {RE_3-ySc_y}[Sc₂](Fe₃)O₁₂, where RE is Sm, Eu, Gd, Tb or Dy and y can be zero with Sm and Eu; {Nd₃}[Sc₂](Fe_zGa_3-z)O₁₂; and other Nd-Sc-Fe garnets of the type {Nd_3-(w+y)M_wS_cy}[Sc₂](Fe …

Separations Of Multicomponent Mixtures Via Thermal Parametric Pumping, John Daniel Stokes

Dissertations

This dissertation covers the separation of solutes from multicomponent solutions via direct mode thermal parametric pumping.

Dilute solution separations were predicted from existing binary equations by assuming the existence of pseudo binary systems, each system consisting of one solute and the common solvent. Two systems, toluene-aniline-n-heptane and toluene-acetophenone-n-heptane with a silica gel adsorbent were used to experimentally demonstrate the separation. Experimental results were in good agreement with the mathematical predictions.

For concentrated multicomponent solutions, the separation was demonstrated by the system, toluene-acetophenone-n-heptane on silica gel. The effects of mass transfer and nonlinear adsorption isotherms became significant and a numerical solution …

The Recovery Of Methanol From The Mother Liquor Of A Pharmaceutical Active Ingredient, Richard Lawrence Eichholtz

Theses

The company has been sending to the sewer the filtrate from one of our chemical processes. This filtrate contains 63 vol. % methanol. The recovery of this methanol would reduce the amount of purchased methanol. The recovery would also reduce the Biological Oxygen Demand of the plant effluent. In the near future the local sewer authority will be billing the company for BOD.

The goal of the recovery process is to obtain methanol of satisfactory quality for reuse in the process from which it came. A literature search and a laboratory study verified the non-ideality of the system. Preliminary calculations …

Subcontracting By The Petrochemical Engineer-Constructor, Michael Peter Skurla

Theses

An analysis has been made of the methods used by a Petrochemical Engineer-Constructor, who has national labor agreements, in deciding if the construction phase of a project should be done by a subcontract method of construction or be accomplished on a direct hire basis. The petrochemical complex under discussion is considered to be in the $75 million range for the total installed cost including design, engineering, procurement, and construction.

The influence of subcontracting portions of the construction phase by the Engineer-Constructor is reviewed with its impact on: the client; project schedule and cost; local and national labor relations, because of …

The Effects Of Angularity On The Compaction And Shear Strength Of A Cohesionless Material, Richard Edward Swiderski

Theses

Several physical methods are described for the practical measurement and rating of angularity (shape) of cohesionless soil particles. Angularity is determined by utilizing the fundamental property of a sphere: a sphere has the smallest contact surface area of any shape for a given volume. Therefore, any other shape will exhibit a greater contact surface area and consequently will have a greater frictional resistance which is a function of its degree of angularity.

The effects of angularity on the physical behavior (e.g. strength) of cohesionless soils was investigated at various relative compaction densities. For this purpose a combined compaction and direct …

Non-Standard Workweek Scheduling Technique Selection, John Alexander Oak

Theses

This thesis presents a description of non-standard work scheduling techniques and a comparison method which enables decision-makers to differentiate between available work-scheduling alternatives with the purpose in mind of selecting the most appropriate and suitable arrangement. The method developed calls for the decision-maker to follow a five-step sequential process to obtain final results. The ingredients necessary to achieve such final results are obtained in a manner similar to that demanded by decision-making-under-uncertainty conditions commonly followed in actual industrial settings.

Since the primary objective of business management is the achievement of a profit through the manipulation of available resources, initial sections …

Reaction Kinetics For The Synthesis Of Benzyl Benzoate From Benzyl Chloride And The Triethylamine Salt Of Benzoic Acid, Michael A. Kolakowski

Theses

The reaction kinetics for the synthesis of benzyl benzoate from benzyl chloride and the triethylamine salt of benzoic acid has been studied over the temperature range of 70-105°C and a mole ratio of benzyl chloride to triethylamine of 0.5 - 10.0.

A reaction mechanism which is consistent with the experimental data has been derived. The experimental data was analyzed by means of the integral method of analysis. The temperature dependency of the reaction was determined from Arrhenius' Law and the activation energy was calculated to be 15,064 cal/g-mole. An empirical equation which explains the effects of the reactant mole ratio …

Prediction And Correlation Of The Salt-Effect In Vapor-Liquid Equilibrium, Enrique M. Bekerman

Theses

The feasibility of developing a method of correlation and prediction, for mixtures of two solvents containing a dissolved salt has been studied. The procedure consisted of arriving at the interaction parameters for the three binary systems (solvent 1-solvent 2, solvent 1-salt, solvent 2-salt) and using these to calculate the ternary results. Attempts to generate interaction parameters for the solvent-salt binaries by means of the Wilson equation were unsuccessful, whereas, use of the NRTL equation resulted in a very good fit of the binary data.

In correlating the ternary results, it became necessary to redefine the liquid phase mole fractions and …

Computerized Conferencing And The Homebound Handicapped, Computerized Conferencing & Communications Center, Murray Turoff, Howard Gage

Computerized Conferencing and Communications Center Reports

Computer conferencing is a relatively new technique which can be applied to improve both the efficiency of education, and communication services available to the homebound handicapped. A system is currently being implemented at the New Jersey Institute of Technology which allows such individuals to engage in a written form of conversation with other individuals or groups. Here the computer stores the discus­sion and keeps track of what everyone has or has not seen, so participants can communicate at a time and pace of their choosing. There is also provision for a range of ancillary facilities such as voting, word processing, …

The Analysis Of The Deflection And Containment Of A Hot Plume By Side Draft Exhaust Hooding, Douglas H. Macgowan

Dissertations and Theses

A common industrial ventilation and pollution problem results when a thermally buoyant polluted plume of air must be exhausted away from a work area to allow achievement of air pollution standards. Generally, a close fitting canopy hood is one of the most effective means of exhaust containment; however, physical restrictions or the operation itself often prevent such an arrangement, and a hood located to the side of the operation is required. This arrangement requires the exhaust to bend and contain the vertically rising plume with a horizontal sweep of exhaust air across the surface of the operation.

A review of …

Evaluation Of The Institute Of Transportation Engineers Program For School Pedestrian Crossing, Nabil Shafiq Hamadeh

Dissertations and Theses

The Technical Council of the Institute of Transportation Engineers (ITE) developed a program for school crossing protection. The intent of this thesis is to evaluate the ITE program within. the context of those programs developed by other agencies throughout the nation. Research materials were obtained from the appropriate Federal, state, local and other agencies through papers, articles, reports and correspondence. Upon the analysis of these sources, the ITE program was found to be deficient in several ways. Recommendations for modifying the program which are set forth herein include a revision of the ITE program including the school route map, clarification …

Bayesian Inquiry: An Approach To The Use Of Experts, King G. Yee

Dissertations and Theses

Subjective information is a valuable resource; however, decisionmakers often ignore it because of difficulties in eliciting it from assessors. This thesis is on Bayesian inquiry and it presents an approach to eliciting subjective information from assessors. Based on the concepts of cascaded inference and Bayesian statistics, the approach is designed to reveal to the decision-maker the way in which the assessor considers his options and the reasons he has for selecting particular alternatives. Unlike previous works on cascaded inferences, the approach here focuses on incoherency. Specifically, it employs the use of additional information to revise and check the estimates. The …

The Design Of An Automatic Electronic Preanodizer, Armen C. Grossenbacher

Dissertations and Theses

The topic of this thesis is the design of an automatic preanodizer to be used to preadjust precision tantalum resistors by anodizing their surfaces. The purpose of the preanodizer is to generate a controllable voltage ramp to be applied to a set of tantalum resistors which are immersed in a suitable electrolyte. The slope and maximum value of the voltage ramp are set to produce the current required for proper anodization of the resistors. The rate of anodization determines the rate of change of the resistor value. This thesis covers the design of an electronic device to meet a set …

Test 1211: Case M-B 4/94 Diesel (Unimog), Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF TEST REPORT GENERAL CONDITIONS Each tractor is a production model equipped for common usage. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operator station. Additional weight can be added as ballast if the manufacturer regularly supplies it for sale. The static tire loads and the inflation pressures must conform to recommendations in the Tire Standards published by the Society of Automotive Engineers. PREPARATION FOR PERFORMANCE RUNS The engine crankcase is drained and refilled with a measured amount of new oil conforming to specifications in the operator’s manual. The fuel …

Analysis Of A Heat Pipe Heat Exchanger, Joseph Olorunfemi Amode

Mechanical Engineering ETDs

One of the more promising applications of the heat pipe is in heat exchangers. Heat pipe heat exchangers may be used as recuperators in heating and ventilating systems, in gas turbines, in steam power plants, and in various process industry applications.

An analysis of the heat pipe heat exchanger was conducted in order to help optimize its performance. A computer program was developed to predict heat pipe performance, finned-tube heat exchanger performance, and the overall per­formance of a finned-tube heat pipe heat exchanger. The computer analysis uses conventional heat exchanger design techniques and a new heat pipe design technique which …

Comment On “Two-Magnon Resonant Raman Scattering In Mnf2”, D. L. Rousseau, R. E. Dietz, P. F. Williams, H. J. Guggenheim

P. F. (Paul Frazer) Williams Publications

We have not been able lo reproduce the recently reported resonance enhancement of Raman scattering from magnons in MnF₂ by Amer, Chiang, and Shen. Fifteen crystals ranging from extremely pure samples to ones with high concentrations of impurities, in addition to one supplied by Amer, Chiang, and Shen, were investigated. By observing the off-resonance scattering, we conclude that if an enhancement of greater than a factor of 2 were present, it would have been seen in our resonance spectra.

Constant-Rate-Of-Strain And Controlled-Gradient Consolidation Testing, C. Thomas Gorman

Kentucky Transportation Center Research Report

Controlled-gradient (CG), constant-rate-of-strain (CRS), and conventional incremental-loading (STD) consolidation testing are compared and evaluated. Undisturbed samples representing three soils common to Kentucky were used in the testing program. Settlements estimated by each testing technique were compared with settlement records from one of the sites. Results of 15 CG, 14 CRS, and 32 STD consolidation tests are shown. No significant differences were noted in values obtained from the three types of consolidation tests. Feasibility of the new test methods for routine testing is briefly discussed and recommendations were made for refinements in testing procedures.

Microbial Bioassay Techniques For Assessing Acid Mine Spoil Amendments For Revegetation, Michael A. Anderson

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

The revegetation of sterile acid mine spoils is a costly and lengthy process due to the many factors (pH, toxic materials, low nutrients, poor soil structure, temperature, moisture, length of growing season, etc.) which impede the establishment of stable plant communities. A microbial bioassay technique applied to soil systems has been developed to allow a rapid (four weeks) and integrated (with respect to nutrients and toxicants) determination of the best amendments for stabilizing mine spoils by revegetation. Using mine spoil from the Blackbird Mine, Cobalt (near Salmon), Idaho, various comb illations of nitrogen, phosphorus, chelators, trace elements, potassium, manure and …

Effects Of Heavy Metals (Cadmium, Copper, And Mercury) On Reproduction, Growth, And Survival Of Brine Shrimp (Artemia Salina) From The Great Salt Lake, Karl A. Gebhardt

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

The purpose of this paper is to report findings concerning the effects of cadmium, copper, and mercury on the brine shrimp Artemia Salina, of the Great Salt Lake. Metal toxicity was observed in relation to acute susceptibility, growth, reproduction, and hatching of the brine shrimp.

Heavy metal concentrations such as cadmium, copper, and mercury are known to be considerably higher in the Great Salt Lake than those in both freshwater and seawater. No published study has been concerned with heavy metal effects on organisms in salinities greater than seawater (35 grams per liter total dissolved solids). The experiments reported …

Development Of A Water Quality Model Applicable To Great Salt Lake, Utah, Craig T. Jones

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

The development of a model capable of predicting the long term (seasonal) distribution of water quality constituents within Great Salt Lake was undertaken as a portion of the ongoing Great Salt Lake project at Utah State University. The overall goal of the project is the development of a modeling framework to assist the relevant decision making bodies in the comprehensive management of the Great Salt Lake system. Phase I of the project provided the overall structural framework for management of the Great Salt Lake system, identified data needs, and established priorities for the development of submodels for incorporation into the …

A Rationale For Furrow Irrigation System Design And Management, Safa Noori Hamad

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

Mathematical and computerized models are developed to design and optimize furrow irrigation systems. The optimization process starts with land grading design, if any is needed, followed by a prediction of maximum non-erosive furrow stream size allowed on a given soil and the associated furrow-advance function. An average depth of application per irrigation is then assumed from which the wetting pattern along the furrow and the amounts of runoff water are predicted. A design of an Irrigation Runoff Recovery System, IRRS, is then executed, if desired, and system cost is determined. Using the predicted wetting pattern and the appropriate Crop Production …

A Survey Of Use Of Left-Turn-On-Red, Kenneth R. Agent

Kentucky Transportation Center Research Report

The objectives of this survey were to determine the extent that a left turn on a red traffic signal (LTOR) has been used across the country and to learn how effective it has been. Responses were received from 43 of the 55 cities surveyed. Of the cities responding, 22 have either had past experience with LTOR or have recently enacted an ordinance which will allow LTOR in the future. Most LTOR laws limit its use to intersections of two one-way streets. A much higher percentage of cities in the western United States have laws permitting LTOR than cities in the …

The Socioeconomic Impact Of The Mountain Parkway And Ky 15, Joseph T. Farmer

Kentucky Transportation Center Research Report

A study of socioeconomic variables in a nine-county region in Eastern Kentucky was undertaken to determine whether significant growth had occurred since the opening of the Mountain Parkway and reconstruction of KY 15. It was hypothesized that these roads have acted as catalysts with available resources to promote a better quality of life.

Study revealed that, while income levels and business sales have enjoyed substantial increases, overall quality of life is still poor. Educational facilities are inadequate; economic diversification in business types is limited; coal is still the main stimulant for income and employment. However, outmigration of persons from the …

Evaluation Of Thermoplastic Pavement-Striping Materials (Louisville And Jefferson County), Jerry G. Pigman, Kenneth R. Agent

Kentucky Transportation Center Research Report

Approximately 1,406,100 linear feet (428,579 m) of hot-sprayed thermoplastic stripe was applied to roadways in Louisville and Jefferson County in the summer of 1973. Visual observations of appearance, durability, and night visibility were conducted according to ASTM D 713-69, the standard method for conducting road service tests on traffic paint. Attempts to conduct photometer measurements of the thermoplastic striping were unsuccessful. Visual observations made during rainy, nighttime conditions were also unsuccessful because very little difference was noticeable among the various sections.

The evaluation showed that the thermoplastic stripes performed considerably better on bituminous concrete pavements than on portland cement concrete …