Digital Commons Network^™

Flexible Pavement Deflections-Methods Of Analysis And Interpretation : Technical Paper, Eldon J. Yoder

JTRP Technical Reports

No abstract provided.

A Model Study Of The Behavior Of Elastic Liners In Shallow Underground Openings, Martin Samuel Oudenhoven

Masters Theses

"Models of epoxy resin were used in a stress freezing technique to determine areas of possible failure in lined circular openings. These models were loaded in a centrifuge for a fixed period of time, after which they were analyzed photoelastically. The material characteristic changes, with time, were recorded on graphs and used in the analysis.

Two types of tests were conducted; one, where the lining thickness was changed and, the other, where materials of the liner and plate material were changed.

The resulting analyses furnished proof that the greater the rigidity of the lining, the higher the stress developed in …

A Study Of The Electro-Chemical Injection Of Ca(Oh)₂ Into Pure Kaolin Clay, Sam Michael Savas Jr.

Masters Theses

"The work presented in this thesis is the investigation and study of a possible and successful means of injecting an electrolyte solution into a fine grain soil mass with the use of electric current and to measure some of the changes of its physical properties. A NoKarb Georgia Kaolin Clay was treated by passing a preferential electrolyte solution of Ca(OH)₂ using direct current for a period of one and six days. The tests performed during this investigation included the following: (a) tri-axial tests, (b) atterberg limits, (c) pH determination, (d) moisture content change (from treatment), (e) visual settling of treated …

A Study Of The Problems Of Design Of Optimum Vibration Absorbers For Multi-Mass Systems, James C. Villegas

Masters Theses

"The purpose of this investigation was to continue the preliminary work of Burrows on the application of tuned and damped vibration absorbers to the reduction of vibratory stresses in a multi-mass torsional vibration system. A hypothetical engine system was chosen for both investigations because it had many complicating factors and gave an eminently practical subject for study.

Attention was centered on the reduction of stresses resulting at higher speeds of the machine system and on developing methods and criteria for the designing of effective absorbers where several modes of vibration exist in the operating speed range of the machine"--Abstract, page …

A Study Of The Stress Distribution Around Circular Openings Using Multilayered Photoelastic Material, Donald Frank Haber

Masters Theses

"Stress analysis as applied to mine openings ranges from the completely empirical to the completely theoretical. However, it is only through the ultimate utilization of the two methods that a guide to the Interpretation of mine stress phenomenon may be obtained. The bridge between the two approaches lies in the field of model study. Specifically, this is an Investigation into determining the feasibility of using multilayered photoelastic materials in models such that a more exact approximation of the underground stress distribution around mine openings can be made.

The two major objectives in this study for determining the feasibility of using …

Model Analysis By The Moiré Method, David D. Kick

Masters Theses

"This study presents the use of Moiré fringes for model analysis of deflections and strains. Deflection of a beam, strain in a disk, and an Influence diagram for a frame are presented as examples of uses of the Moiré method. The necessary equations for the determination of strain using the Moiré method are also derived and presented in this work"--Abstract, page v.

Porous Cooling Of A Pile, Tarsem Singh Purewal

Masters Theses

"In this investigation the problem of a limiting case of steady state one dimensional solid-fluid Newtonian heat transfer is examined in which an incompressible non-heat generating coolant fluid is flowing through a heat generating porous plate.

The effect of grain size on the Newtonian heat transfer in the porous plate with various kinds of internal heat generations is determined analytically. The temperature difference between the solid and the coolant fluid through the porous plate is determined. All the previous studies assume that in the porous plate, coolant fluid temperature and solid temperatures are approximately equal. This analysis eliminates this simplifying …

A Study Of Several Commercial Steels In The Red Short Range, Jorge Alberto Espana

Masters Theses

"The red short phenomenon present in steel, was studied by means of torsion tests at temperatures between 800 and 1200⁰C. Cold drawn bars of different compositions of steels were tested, and the number of turns to failure and maximum twisting torque were plotted versus temperature.

All the steels tested, exhibited to have a certain degree of red shortness. By comparing the curves and the respective chemical analyses, the detrimental effect of sulphur and lead and the beneficial effect of manganese, was established.

Microscopic examinations revealed the intergranular nature of the cracks in the red short range. Sulphur and oxide distribution …

Permeability Of Poly (Ethylene Terephthalate), James G. Harvey

Masters Theses

"Corrosion is a phenomenon which has been the subject of extensive research, in order to find a way to control or completely stop it. Two general methods, either placing the material which corrodes in an anti-corrosive atmosphere or protecting the material which corrodes from the corrosive atmosphere, are the chief means of preventing corrosion today.

The second method is probably most widely used presently. One of the most important methods of protection is by means of organic protective coatings, or paints, but at best these only retard corrosion, due to the fact that corrosive media e.g. water vapor, ions etc. …

Development Of A Simple Bar Method Thermal Conductivity Test, V. J. Flanigan

Masters Theses

"A linear flow bar method type apparatus was set up for finding thermal conductivities by comparison techniques. Comparison technique consist of using a standard specimen where the thermal conductivity is known and comparing it to the unknown specimens to find their conductivity. Apparatus of this type usually uses thermocouples for the required temperature measurements, but thermistors were used in this experiment. The thermistors used required calibration to measure accurate temperatures and this was accomplished by using the known temperatures of the changes of state of some common materials. Five alloys were used to evaluate the method: SAE 1020 steel, gray …

The Effect Of The Rolling Load On The Micro-Structure Of Low Carbon Sheet Steel, Jerry Lee Cadden

Masters Theses

"A Stanat 315, two high-four high, combination rolling mill is used to cold roll annealed, low carbon steel strips. A method of measuring the rolling load was presented. The method consisted of constructing a load cell using SR-4 strain gages attached to a steel column. The load cell was placed under the hold down screw of the rolling mill and a known load was applied. The stresses from this load were transferred to the mill housing where another SR-4 strain gage was located. The strain in the mill housing was recorded at the corresponding applied load. During rolling, the strain …

Transpiration Cooling Of A Porous Plate, Stephan A. Sayegh

Masters Theses

"Transpiration cooling has long been known as an effective way of removing heat from porous materials. This thesis is a new approach to one of the problems of transpiration cooling in the steady state.

The specific problem considered here is that of a uniform porous plate through which a liquid is forced. This liquid vaporizes at a short distance from the surface through which it is forced and leaves the porous plate at the other surface which is exposed to hot gases. It also protects the hot surface by forming an insulating layer between that surface and the hot gases. …

Mechanics Of The Voussoir Arch As Applied To Block Caving, Christopher Haycocks

Masters Theses

"The theories of ground failure in massive rock with special reference to the problem of the mechanics of block caving were studied and evaluated.

The mechanics of arch or dome formation underground were studied quantitatively using the Voussoir arch theory. The effect of shear stress on the arch stability was considered and found to affect the system only when the arch height increased beyond certain limits.

A theory of the mechanism of ground failure in an undercut block using the dome theory was advanced. Photo- elastic model studies were used to support the conclusions reached"--Abstract, page i.

Thermal Conductometer For Liquids, Yuan-Kai Chang

Masters Theses

"The published data pertaining to the thermal conductivity of liquids are of such a character that it is very difficult to determine from them the correct value, or the temperature coefficient for any liquid.

Most of the published values of thermal conductivity for liquids are evaluated at one particular temperature. It is the purpose of this investigation to design, construct and calibrate a thermal conductometer for liquids over a temperature range of 30°F to 200°F.

Since water and glycerol were the only liquids found by this investigator with published data on their conductivities as a function of temperature, they were …

Electrodeposition Of Antimony From Sulfide Melts, Mahendra N. Rana

Masters Theses

"A study of the current-potential relationships, and the electrodeposition of antimony metal was conducted for fused mixtures of Sb₂S₃-Na₂S, Sb₂S₃-Sb and Sb₂S₃-NaCl-KCl in the temperature range of 700° - 900°C. An attempt was made to determine the mutual solubility of molten antimony and Sb₂S₃-Na₂S melts. The microstructure of deposited metal was studied metallographically. Analysis of phases present in the matte mixture (Sb₂S₃-Na₂S) was made by x-ray diffraction patterns.

All investigations were carried out in …

A Survey Of The Influence Of Selected Sulfides On The Thermal Decomposition Rate Of Zinc Sulfate, L. G. Twidwell

Masters Theses

"The influence which ZnS, CdS, Cu₂S, PbS, and FeS has on the thermal decomposition rate of ZnSO₄ was studied by measuring the SO₂ gas evolved per unit of time for various ZnSO₄-MeS mixtures at 600°C, and analyzing the solid phases by means of X-ray diffraction patterns.

The SO₂ gas evolved upon heating the pellets was analyzed as a function of time by absorbing the gas in a solution of distilled water, H₂O₂, and NaOH, and measuring the time required for the SO₂ to neutralize the NaOH. The gas …

The Irish Plumber And Heating Contractor, December 1961 (Complete Issue)

Building Services Engineering

No abstract provided.

The Irish Plumber And Heating Contractor, November 1961 (Complete Issue)

Building Services Engineering

No abstract provided.

The Irish Plumber And Heating Contractor, September 1961 (Complete Issue)

Building Services Engineering

No abstract provided.

The Design Of A Six Specimen Tensile Fatigue Machine, Charles Mark Percival

Theses and Dissertations

Although metal fatigue has been recognized for many years and during that time many persons have tried to find the explanation for it, there is still not a complete theory concerning this phenomenon. Metal fatigue is one of the major problems the modem designer must face. If the design techniques are to progress as other technological advances are made, it is evident that it will involve a better understanding of metal fatigue.

Investigation Of The Platinum-Rich Portion Of The Platinum-Tantalum Phase Diagram, Bob Dean Browning

Theses and Dissertations

The Pt-Ta binary system was investigated at two isotherms;1000°C and 1500°C, and at eleven alloy compositions in the range of 50 to 100 atomic percent platinum. The alloys were examined by x-ray diffraction and metallography. Three intermetallic compounds, Pt₂Ta, Pt₃Ta, and Pt₄Ta were found to exist in this composition range. The Pt₄Ta intermetallic appeared only at the 1500°C isotherm. Platinum dissolved tantalum substitutionally to 90 atomic percent at 1500 °C and to approximately 80 atomic percent at 1000 °C.

The Irish Plumber And Heating Contractor, July 1961 (Complete Issue)

Building Services Engineering

No abstract provided.

Electrolytic Amalgam Reduction Of Cinnamic Acid, Alan Ira Mytelka

Theses

The use of sodium amalgam and potassium amalgam to reduce cinnamic acid to hydrocinnamic acid was accomplished in two concentrically constructed cylindrical cells.

In the outer cell, liquid amalgam was prepared electrolytically using a mercury cathode. The amalgam was moved by a rocking motion into the inner cell where the cinnamic acid dissolved in ethanol was reduced to hydrocinnamic acid. The actual percent conversion as measured by iodine numbers varied from 6.0% to 567, the percentage depending upon the number of coulombs passed into the electrolytic cell, the amalgam used, and whether or not stirring in the inner reduction cell …

Effect Of Elevated Temperature On Efficiency Of Corrosion Inhibitors, Walter Dzingala

Theses

An experimental program was set up to investigate the effect of temperature on the protection efficiency of various inhibitors of metal corrosion. Contrary to most studies, an appreciable amount of the work was done with the corrosive effect being determined on the metal specimens that were exposed first to the inhibitor, then to air at different temperature, and finally to the corrosive medium with no inhibitor present. The purpose being to determine whether the inhibitor treatment would provide a permanent protection for a metal surface or would it be necessary to furnish a continuous supply of the inhibitor to the …

Viscosity Correlations Of Saturated Fatty Acids And Their Esters, Thomas Joseph Redling

Theses

Several correlations have been developed which permit calculation of the viscosities of the n-paraffin fatty acids and esters, beginning with formic and including stearic acid.

The correlations were obtained by interrelating the Log u and the Log P_v at the same temperature, where u is the viscosity in centipoise and P_v is the vapor pressure in millimeters Hg. A single line relationship represents all the fatty acids from propionic acid to and including stearic acid, while formic acid and acetic acid each have their own line. Methyl, ethyl, propyl and butyl formate can be represented by a single …

Attrition In A Fluidized Bed, Andrew Joseph Welter

Theses

The object of this thesis is to study attrition in a fluidized bed in an attempt to find a reliable method for predicting attrition rate when fluid flow rates and particle sizes are varied.

The system studied consisted of air as the fluidizing median with bauxite and fuller's earth as the solids in suspension. Fluid flow rates were changed while all other variables were held constant. Systems with both large and small particles were studied for each material.

It was found that the attrition rate of the material when the bed is maintained at a constant mass flow rate is …

The Influence Of Water-Reducing Admixtures On The Curing Of Concrete, Wallace Don Budge

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

The use of water-reducing admixtures in concrete has grown continuously since their introduction over 25 years ago, with a present estimated usage in the production of 25 million cubic yards of concrete annually in the United States alone. Opposition to anything added to concrete, other than cement, aggregates, and water, is gradually disappearing, and considerable recognition is being given to the value of using other ingredients.

The research contained in this study may be divided into two portions: tests to determine the rate of volume change of cement paste and compressive strength tests to indicate the effect of moist curing …

The Irish Plumber And Heating Contractor, May 1961 (Complete Issue)

Building Services Engineering

No abstract provided.

Proposed Special Specifications For Lightweight Concrete, James H. Havens

Kentucky Transportation Center Research Report

No abstract provided.

The Irish Plumber And Heating Contractor, April 1961 (Complete Issue)

Building Services Engineering

No abstract provided.