Digital Commons Network^™

Australian Tractor Test Report. No. 56. Zetor 5511, G H. Vasey, W. F. Baillie

Journal of the Department of Agriculture, Western Australia, Series 4

AUSTRALIAN TRACTOR TEST REPORT

The Zetor 5511 is a general purpose farm tractor. With 43 drawbar horsepower and 51 h.p. at the P.T.O. at rated engine speed it comes within Class 5 of Australian Standard Classification of Wheeled Tractors for Agricultural Purposes, A.S. Dl0-1967. It is equipped with 18.4 x 28 pneumatic tyres.

It has a five-speed gear box with a High and Low ratio change giving 10 forward and 2 reverse speeds

Super Spreader Distributes Snail Baits, G D. Rimes, W. M. O'Donnell

Journal of the Department of Agriculture, Western Australia, Series 4

THE problem of distributing snail bait on broad acres has been overcome by simple modifications to a conventional super spreader.

Urea Drilled With Seed Affects Germination And Yield, M G. Mason, A. Loutit, J. A. C. Smith, D. Highman, P. Stallwood

Journal of the Department of Agriculture, Western Australia, Series 4

Trials in 1968 at Burracoppin and York again showed it is safer to topdress urea just before seeding than to drill a mixture of seed and urea.

At all but the lowest urea rates, urea drilled with the seed reduced the number of plants emerging and surviving, and reduced final wheat yields.

The Setting And Control Of Disc Ploughs, P A. Taylor

Journal of the Department of Agriculture, Western Australia, Series 4

THE trailed disc plough is the most commonly used tillage implement in Australian broadacre farming, yet it is considered in some areas to be difficult to set and to operate. These notes provide information resulting from C.S.I.R.O. research to assist operators in the control and operation of trailed disc ploughs.

How Many Acres Per Hour?, J G. Drever

Journal of the Department of Agriculture, Western Australia, Series 4

MANY farm tractor operators don't know exactly how much land is covered in an hour by implements drawn by their tractors. This information, useful on any farm where tractors are used, is of particular value in contract work.

The capacity of the machine or implement, or in other words, its rate of working, depends on the width of the machine, how fast it travels, how efficiently it is operated and the time it works.

Electrochemical Reduction Of Chromate In The Presence Of Nickel Chloride In Molten Lithium Chloride-Potassium Chloride Eutectic, Branko N. Popov, H. A. Laitinen

Faculty Publications

Chronopotentiometry of chromate in the presence of NiCl₂ in molten LiCl-KCl eutectic reveals a diffusion controlled, three electron reduction step. In the presence of excess NiCl₂, chromate is reduced at −0.35V vs. Pt(II)/Pt reference electrode and the electroactive species responsible for the chrono-potentiometric wave is estimated to have a diffusion coefficient of 1.06 · 10⁻⁵ cm² sec⁻¹ at 450°C. The stoichiometry of the reduction product depends mainly on the temperature at which the deposit is formed. At 500°C the deposit approaches the composition LiNi₂CrO₄. X-ray powder diffraction shows the deposit …

An Explicit Simulation Of Overland Flow, Glendon Taylor Stevens

Masters Theses

"Computer simulation of overland flow requires a mathematical model which converges to a true solution. This paper presents a method, based on measurable physical parameters, which insures convergence of a fixed grid explicit numerical solution. Analysis of a wide range of overland flow plane parameters has resulted in an equation of the form Δt = 0. 2 ΔX/S_o, for the time step increment. This equation provides values for Δt that will insure stability and convergence of the fixed grid explicit numerical method of solving the spatially varied unsteady flow equations. The effect of subarea shape on the rising …

Determination Of Reservoir Characteristics From Capillary Pressure Curves And Electrical Properties Of Rocks, Prasanta Kumar Guharoy

Masters Theses

"Based upon the assumptions that a porous medium is analogous to a bundle of capillary tubes and that there is equivalence of electrical and hydraulic tortuosity in a porous medium, empirical expressions are presented which relate capillary pressure data and electrical properties of the rock to the porosity, permeability and relative-water permeability, respectively, of completely water-wet rocks. Experimental data are presented for comparison in order to verify their validity. Three principal models are presented, each of which is characterized by a particular expression for estimating tortuosity. The method of determining this parameter was varied in order to find the form …

Fault Detection In Asynchronous Sequential Circuits, Jeng-Chuan Kau

Masters Theses

"As the asynchronous sequential circuit has become more and more important to digital systems in recent years high reliability and simple maintenance of the circuit is stressed. This paper presents a fault-detection algorithm which will be applicable to most of the practical asynchronous sequential circuits. The asynchronous sequential circuit is treated from the combinatoric point of view. First the minimal set of states, both stable states and unstable states, sufficient to detect all possible faults of the circuit is found from the fault table. Then a test sequence is generated to go through these states. It is assumed that testing …

The Electrochemical Behavior Of Molybdenum In Acidic Chloride Solutions, Mun-Shan Lee

Masters Theses

"The anodic dissolution of Mo was studied in HC1-KC1 solutions at 25ºC. The apparent valences of Mo ions going into solution were approximately six. Lower values were obtained in HC1 solutions, with the most pronounced changes occurring with the higher concentrations. The resultant ions in solution were Mo-VI. The Mo surface in aqueous solutions appears to be covered with an oxide whose approximate composition is Mo₂O₅. The anodic dissolution is controlled by the oxidation of the surface oxide (Mo₂O₅) to MoO₃"--Abstract, page 1.

A Study Of The Composite Action Of Light Gage Steel Deck And Concrete, Charles Sherman Bach Jr.

Masters Theses

"This thesis is on the investigation of corrugated light-gage steel sheets used as the tension reinforcement for concrete slabs. The steel sheets used had embossments placed at uniform intervals over the entire length of the sheets. The composite concrete and light-gage deck steel were tested to determine a method of design for this type of composite section from an economical, safe and practical standpoint. The investigation covered the flexural, shear and bond capacity of this type of composite section"--Abstract, page ii.

Influence Of Film Thickness On The Performance Of Solid Lubricants, Sunil Vishwanath Mahale

Masters Theses

"The object of this investigation was to determine the effect of lubricant film thickness on the coefficient of friction and on the wear life of solid lubricants. Bonded molybdenum disulphide and bonded graphite were the lubricants tested. Dow Corning's LFW-1 and Falex lubricant tester were the two machines used for testing these lubricants. The lubricants were sprayed on the specimen surface. Pretreatment, spraying and curlng were done according to standard or manufacturer's recommended procedures. During the entire research, the procedure for experimentation was followed according to ASTM No. 2625 on Falex and CRC recommendations on LFW-1 machine. It was found …

Influence Of Some Interstitial Materials On The Thermal Contact Conductance, Jin-Tyan Lin

Masters Theses

"Experiments have been conducted to investigate the effect of the interstitial materials at the interface of metals in contact. The test specimens were cylinders, axially aligned and loaded. Specimen materials were 606l-T6 aluminum alloy, and the contact fillers were stainless steel wire screens, aluminum foil, paper, and dielectric greases. The tests were conducted at atmospheric environment. The contact pressure ranged from 25 psi to 600 psi. The mean interface temperature ranged from 100 ºF to 200 ºF. Surface roughnesses of specimens were from 25 to 35 micro-inches, rms. The results of the investigation reveal that if the contact surfaces are …

A Socio-Economic Traffic Demand Prediction Model Based On A Lumped System Approach, John Edward Thompson

Masters Theses

"The objective of this investigation was to devise a method for predicting transportation system demand based on socio-economic variables of certain physical areas. This pilot study was performed utilizing traffic flow, but minor mathematical alterations could change the transportation system to urban mass transit usage demand. An area of uniform socio-economic characteristics can be delineated and the socio-economic characteristics isolated. Each area will place a distinct demand on some existing transportation facility based on those characteristics. The physical demand can be approximated by a theoretical probability distribution. Once this internal flow generation has been approximated by the frequency distribution, it …

Transient Response Of A Vibration Isolation System, Hemendra Shantilal Acharya

Masters Theses

"A practical procedure for investigating the performance of a vibration isolation system under transient conditions is presented. For this investigation, an induction motor with an unbalanced rotor is studied during the period when it accelerates to its operating speed from rest. Using Newton's second law of motion, equations of motion are derived, first neglecting and then considering the effect of "inertia torque". This torque is produced by the inertia force resulting from vertical acceleration of the unbalanced mass. The equations are solved on a digital computer using the Runge-Kutta method of order 4. The results obtained are compared with those …

The Anodic Dissolution Of Tin In Acidic Chloride Solutions, Edward Chung-Hong Liu

Masters Theses

"The anodic dissolution of Sn in acidic chloride solutions (pH = -2.0 to 2.9) was studied at 25ºC. The apparent valence of the dissolving ions varied from about 0.4 to 2.4, a function of both electrolyte and c.d. The complexing of Sn⁺² by Cl⁻ had an important influence with SnCl₃⁻ apparently being the dominant products. A reaction sequence is proposed involving the step-wide oxidation of Sn accompanied by reaction with Cl⁻"--Abstract, page 1.

Turbulent Structure In The Wake Of Sphere, Darrell W. Pepper

Masters Theses

"The study of turbulent wakes is considered necessary to understand the droplet behavior associated with the collision coalescence phenomena in atmospheric clouds. The Vertical Atmospheric Wind Tunnel enables experiments dealing with this droplet behavior to be analyzed. The experiments conducted in the UMR Vertical Atmospheric Wind Tunnel consist of two parts: one is the investigation of the flow field characteristics in the test section of the wind tunnel; the other is the measurement of the turbulent structure in the wake of a sphere. The test section is rectangular in design and has a cross-sectional area of 36 square inches (6 …

An Analysis Of A Quadrature Double-Sideband/Frequency Modulated Communication System, Denny Ray Townson

Masters Theses

"A QDSB/FM communication system is analyzed with emphasis placed on the QDSB demodulation process and the AGC action in the FM transmitter. The effect of noise in both the pilot and message signals is investigated. The detection gain and mean square error is calculated for the QDSB baseband demodulation process. The mean square error is also evaluated for the QDSB/FM system. The AGC circuit is simulated on a digital computer. Errors introduced into the AGC system are analyzed with emphasis placed on nonlinear gain functions for the voltage controlled amplifier"--Abstract, page ii.

The Cathodic Reduction Of Bromate Ions On Mercury In Neutral And Basic Solutions, Jaw-Shin Chang

Masters Theses

"The reduction of BrO⁻₃ was studied in neutral and basic solutions on a stationary Hg surface under activation controlled conditions. Coulombic efficiency studies showed that BrO⁻₃; was reduced to Br⁻ with high efficiencies. The polarization measurements lead to a proposed reaction scheme which is consistent with the experimental observations"--Abstract, page 1.

Computer Time-Sharing (T-S) "An Engineering Tool" For The Engineering Applications Of The Small Company, James Binford Summers

Masters Theses

"The objectives of this investigation were to illustrate the capabilities of the time-sharing (T-S) industry, identify the means by which the small sized company, with a need to solve engineering problems, can best be served through T-S, and to present T-S to these potential users. Investigation was made of distinctive T-S services to formulate a composite of the T-S industry. Examples of three distinctive T-S services were used within this composite to exemplify the variations of services within the industry. The methods a small company could use to utilize computer services were identified emphasizing T-S as the method best suited …

Mutually Dependent Heat And Mass Transfer In Laminar Tube Flow, Gary Alfred Scheffel

Masters Theses

"An investigation is performed of the mutually dependent heat and mass transfer in laminar and hydrodynamically fully developed gas flow in a tube. Sublimation of mass occurs at the tube wall so that heat and mass transfer take place between the wall and the flowing gas stream. The wall of the tube is thermally insulated from the external environment with the result that the heat of sublimation is supplied by convective transport from the gas. The solution of this problem requires the simultaneous consideration of the energy and diffusion equations, with coupling provided by the boundary conditions. Mathematical expressions are …

The Anodic Oxidation Of Oxalic Acid On Au, Steven C. Mueller

Masters Theses

"The anodic oxidation of oxalic acid on Au has been studied at 80°C in aqueous media. The reaction rate was measured as a function of potential, oxalic acid concentration, pH, and temperature in H₂SO₄-K₂SO₄-KOH solutions of unit ionic strength. The oxalic acid was oxidized only in acidic media. The oxidation to CO₂ was essentially complete. A first order dependence of the rate on both pH and undissociated oxalic acid was found. A mechanism is proposed in which the first decarboxylation is the rate determining step"--Abstract, page 1.

On The Flow Near An Enclosed Rotating Blade In The Neighborhood Of The Ground, Tze-Lien Liang

Masters Theses

"The flow in the vicinity of an enclosed rotating blade near the ground was studied both analytically and experimentally. Experimental results were obtained by making pitot tube traverses across the face of the housing but gave only a qualitative indication of the velocity distribution. Tufts of strings were used to locate the flow directions in the vicinity of the ground and the housing. The two dimensional potential flow solution was found to yield unreasonable results for this flow configuration due to viscous and rotative effects. The three-dimensional Navier-Stokes equations were solved numerically by using the successive underrelaxation method. The results …

Analysis And Control Of Noise Produced By Small Pneumatic Tools, Phillip Ray Elam

Masters Theses

"Noise measurements were made near the exhaust of three small pneumatic tools operating under various loads and with various components removed. One-third octave analyses were performed on the noise for identification of noise sources and to determine possible noise reduction techniques. It was determined that the noise spectra consisted of broad band turbulent flow noise plus periodic components at the tool motor blade passage frequency and harmonics of this frequency. One tool, the nut setter, was selected for reverberant field noise analyses and noise reduction studies. Reverberant field measurements indicated that most of the tool noise was transmitted through the …

Thermal Expansion Of Orthorhombic Pbo, Charles A. Sorrell

Materials Science and Engineering Faculty Research & Creative Works

Thermal expansion of orthorhombic PbO was investigated by high‐temperature X‐ray diffraction. The coefficients in the a0, and c0 directions are equal and Pb–O chains extended in the a0 direction and bonded into layers in the b0 direction; appreciable Pb–Pb bonding is indicated. Coordination and bond distances observed in PbSiO3 and lead silicate glasses, which are similar to those of massicot, and PbnOn polymeric units reported in PbO vapor are interpreted as additional evidence of the importance of PbO chains as structural entities. Copyright © 1970, Wiley Blackwell. All rights reserved

Analysis Of Concrete Slabs On Ground And Subjected To Warping And Moving Loads: Technical Paper, Karl Harcourt Lewis, Milton Edward Harr

JTRP Technical Reports

No abstract provided.

Time And Load Independent Properties Of Bituminous Mixtures: Technical Paper, S. A. Swami, William Harner Goetz, Milton Edward Harr

JTRP Technical Reports

No abstract provided.

Precast, Prestressed Concrete For Bridge Decks : Technical Paper, Martin J. Gutzwiller, Robert H. Lee, Charles F. Scholer

JTRP Technical Reports

No abstract provided.

Flow In Aggregate-Binder Mixes : Technical Paper, Egons Tons, William Harner Goetz, Virgil L. Anderson

JTRP Technical Reports

No abstract provided.

Nuclear Radiation Enhancement Of Transistor Forward Gain At High Frequencies, C. A. Goben, Y. P. Han

Electrical and Computer Engineering Faculty Research & Creative Works

This investigation has characterized the effects of fast neutron bombardment on a typical n-p-n transistor (2N914) of a common emitter amplifier operating at high-frequencies (>100 MHz) by means of s-parameter measurements from 120 MHz to 350 MHz, inclusive, every 10 MHz. The changes in the four (4) s-parameters and the trends and consequences of neutron bombardment are examined pictorially on graphs. The general effect of fast neutron bombardment is to decrease the magnitude of each s-parameter for frequencies below z. fT (where z = (O/1013)0.1). However, if the device is operating above z fT, the magnitudes of s11 (input …