Digital Commons Network^™

Structure Of High-Internal-Phase-Ratio Emulsions, K. J. Lissant, B. W. Peace, S. H. Wu, K. (Kenneth) G. Mayhan

Chemical and Biochemical Engineering Faculty Research & Creative Works

No abstract provided.

Towards A Design Of Hmo, An Integrated Hardware Microcode Optimizer, James Oliver Bondi

Doctoral Dissertations

"This paper discusses an algorithm for optimizing the density and parallelism of microcoded routines in micro-programmable machines. Besides presenting the algorithm itself, this research also analyzes the algorithm's uses, design integration problems, architectural requirements, and adaptability to conventional machine characteristics. Even though the paper proposes a hardware implementation of the algorithm, the algorithm is viewed as an integral part of the entire microcode generation and usage process, from initial high-level input into a software microcode compiler down to machine-level execution of the resultant microcode on the host machine. It is believed that, by removing much of the traditionally time-consuming and …

Mathematical Simulation Of Gas And Water Coning In Petroleum Reservoirs By The Dynamic Material Balance Technique, Visheshwar Nath Simlote

Doctoral Dissertations

"The prediction of coning behavior at a producing oil well is one of the most difficult numerical simulation problems. Because of the convergent flow patterns and small sizes of the inner grid blocks, the radial coordinate models used to study the problem have a tendency to become unstable. Since several hundred pore volumes may flow through the inner grid blocks during a rather small time interval, instabilities are likely to occur in the saturation calculations for these grid blocks. The dynamic approach to saturation calculations is a method which first computes the correct material balance and then calculates the saturation …

Magnetostrictive Aftereffects In A Dilute 50fe-50ni-C Alloy, Raj N. Master

Masters Theses

"Crystallographically equivalent interstitial sites are energetically equivalent when the host crystal is free of any fields. This situation is shown in Fig. Pl from which it may be appreciated that the difference of the free energy of the "crystal" with an interstitial "I" located in "x" and "y" sites, respectively, is equal to zero. This energy equivalence of the various interstitial sites is destroyed when the host crystal is subjected to fields such as strain fields, magnetization fields or a combination of both as may be appreciated from Figs. P2 through P4. In this case, the interstitials will preferentially occupy …

The Morphology Of Cellular Precipitation In Magnesium Rich Magnesium-Aluminum Alloys, Jyong Shi Cho

Doctoral Dissertations

"The morphology of cellular precipitation in a Mg-9wt. %AI alloy has been investigated by light and electron microscopy. A study of the early stages of the cellular precipitation process indicated that cellular precipitate structure forms in Mg-Al alloys by Fournelle and Clark mechanism. "Replacive" motion indicative of the Tu and Turnbull mechanism for cellular precipitation was not seen"--Abstract, page 1.

Hybrid Carrier And Modulation Tracking Loop Performance In Rfi, Rodger E. Ziemer, Donald R. Nelson

Electrical and Computer Engineering Faculty Research & Creative Works

The operation of a hybrid Tracking (HT) phase-locked loop (PLL) in radio-frequency interference (RFI) is considered. Results from a perturbation analysis for the loop phase error in continuous-wave (CW) RFI are found to compare favorably with results obtained by digital computer simulation. These results, together with simulation results for wide-band (in comparison to the loop bandwidth) RFI, indicate that loop structures which track both on the signal carrier and modulation components are advantageous in RFI plus Gaussian noise backgrounds. Copyright © 1974 by The Institute of Electrical and Electronics Engineers, Inc.

Shell Roofs And Grain Bins Made Of Corrugated Steel Sheets, M. N. El-Atrouzy, George Abdel-Sayed

CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)

No abstract provided.

Minimum Cost Design Of Water Distribution Systems, Don J. Wood, C. O. Charles

KWRRI Research Reports

The objective of this study was to develop the analytical tools and procedures for minimum cost design of water distribution systems. Both analog and digital means of carrying out pressure and flow calculations were developed. As a result of this effort, digital programs for pressure and flow calculations in water distribution systems were written and have been widely distributed to practicing engineers. One procedure is based on a direct solution of the basic system equations using a linearization scheme and has several advantages over conventional techniques such as the Hardy Cross method. These include avoiding the need to initially balance …

In Situ Shear Strength Parameters By Dutch Cone Penetration Tests, C. Thomas Gorman, Tommy C. Hopkins, Vincent P. Drnevich

Kentucky Transportation Center Research Report

Dutch cone penetration testing was performed and undisturbed samples were collected at four Kentucky highway sites. Shear strength, as determined by consolidated, undrained triaxial testing of the undisturbed samples, was correlated with friction resistance as measured by the Dutch friction cone. Statistical analysis of all data showed shear strength to be about 80 percent of friction resistance. Recommendations for the use of the Dutch cone penetration test in Kentucky soils were also made.

Response Of Orthotropic Bridge Decks To Highway Loadings, Harry Morris Rexin

Dissertations and Theses

This thesis documents the fabrication, testing techniques, and response of a plastic scale model of an orthotropic bridge deck. To economically investigate a two-lane steel bridge deck, plastic Acrylic^R was used as a modeling material. Welds were simulated with dichloromethane, a capillary action solvent, and PS-30, a polymerizable cement. Deflections were measured with laboratory dial guages while strains were monitored with strain guages mounted on the deck.

The response of the deck to AASHO vehicle axle loads was compared with a discrete element computer program used to analyze orthotropic bridge decks continuous over flexible supports. Results indicate good correlation …

Problems Of Measurement In The Environmental Field, Harold M. Cota

Civil and Environmental Engineering

No abstract provided.

Bulletin - June, 1973, Civil Aviation Medical Association

Browse all Civil Aviation Medical Association Newsletters

A four page newsletter of the Civil Aviation Medical Association. The newsletter provided news about civil aviation medicine and information related to the organization.

Effects Of High Altitude Jet Aircraft On The Stratosphere, Dennis K. Bushnell

Retrospective Theses and Dissertations

This paper presents a review of the basic thermal, chemical and radiation balances existing in the atmosphere and discusses the mechanisms by which jet engine exhaust products can disturb these balances. Possible effects of stratospheric pollution on plant and animal life are discussed. Methods for reducing harmful emissions through engine design modifications are outlined and current successful research programs are surveyed. The SST type aircraft is shown to be a greater threat to the environment than conventional jets because of differences in cruise altitudes. It is concluded that due to the existence of several potential environmental problems associated with contamination …

Generalized Feedback Shift Register Pseudorandom Number Algorithm, Theodore Gyle Lewis, W. H. Payne

Electrical and Computer Engineering Faculty Research & Creative Works

The generalized feedback shift register pseudorandom number algorithm has several advantages over all other pseudorandom number generators. These advantages are: (1) it produces multidimensional pseudorandom numbers; (2) it has an arbitrarily long period independent of the word size of the computer on which it is implemented; (3) it is faster than other pseudorandom number generators; (4) the "same" floating-point pseudorandom number sequence is obtained on any machine, that is, the high order mantissa bits of each pseudorandom number agree on all machines— examples are given for IBM 360, Sperry-Rand-Univac 1108, Control Data 6000, and Hewlett-Packard 2100 series computers; (5) it …

Computer-Aided Design Of Light Aircraft To Meet Certain Aerodynamic And Structural Requirements, Joanne Lynn Walsh

Mechanical & Aerospace Engineering Theses & Dissertations

Nonlinear mathematical programming techniques are applied to a particular aircraft design problem, that of determining the maximum range design for light aircraft subject to certain aerodynamic and structural requirements. Search techniques available in an existing nonlinear optimization computer program, AESOP, are applied to the design problem. Seven design variables are used to define the wing dimensions, the wing skin thickness, the cruise velocity, the amount of fuel carried, and the engine horsepower. The influence of different design requirements on the range is observed and discussed.

Representation And Characterization Of Thixotropic Fluids, Huei-Hsiung Wang

Dissertations

Thixotropy is a time-dependent rheological behavior of a group of fluids which are characterized by an isothermal reversible breakdown induced by a mechanical disturbance. Based on this definition, a mathematical model of reversible degradation kinetics is set up. Its development leads to two equations which represent quantitatively the hysteresis loop and torque-decay curve. These equations consist of five independent parameters with their physical meanings. These parameters can be used to characterize the properties of thixotropic materials.

The original Weissenberg Rheogoniometer was modified to measure the thixotropic behavior of blood with the step change and the ramboid change of shear rate. …

The Quantitative Characterization Of Middle Distillate Fuels For Reduced Smoke Emission And Improved Low Temperature Operability, R. S. Feamster

Theses

Forty-eight inference equations are presented to approximate the hydrocarbon composition of middle distillate fuels and of the solids separating from these fuels at temperatures below their cloud points by consideration of fuel physical inspections. The physical inspections consist of API gravity, aniline point, cloud point, and distillation curves for ten fuels from major United States and European refineries. To determine the percentage of solids separating from cooled fuels, each fuel is filtered over a temperature range from the cloud point to -40 F in 10 F increments. Aromatic, naphthenic, and paraffinic hydrocarbon contents and the r-paraffin carbon number distributions of …

Stress-Relaxation Of Cross-Linked Polyethylene At Elevated Temperature, Ravio Luik

Theses

Polyethylene because of its excellent chemical, physical, mechanical and electrical properties, as well as its easy adaptability to extrusion, molding and other processes and its low cost has become a very widely used material for hundreds of applications. But, because it is a thermoplastic, it also deforms and flows when temperatures approach or exceed the crystalline melting point. This handicap, however, can be reduced by crosslinking the polymer chains and thereby converting the thermoplastic to a thermoset material. To further expand the possible uses of this popular material and to further improve the properties, fillers and antioxidants may be compounded …

The Photolysis Of Chlorobenzene In An Aqueous Environment, Louis John Del Tufo

Theses

Chlorobenzene was chosen as a model system for the study of photochemically induced reactions in an aqueous environment. It was the goal of this research to achieve a reaction system which best approximates conditions existing in the environment. To do this, a basic model system was established, and then the effect on the rate by various parameters was studied. These parameters, which included the presence of oxygen and such inorganic compounds as might be present in receiving waters, (e.g. nitrate, sulfate, and phosphate), were chosen so as to meet the goal of this research.

Kinetic data was obtained for seven …

Velocity Distribution Versus Sediment In The Missouri River, Glendon Taylor Stevens, Terence E. Harbaugh, Paul R. Munger

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Analysis of the large quantities of velocity and sediment data gathered on the Missouri River has not been undertaken in the past due to the heavy workloads of U.S. Army Corps of Engineers staff. The need to undertake this effort has long been recognized by both the Kansas City District and the Omaha Division. As a result of this need, the Kansas City District, Corps of Engineers, entered into a contract with the curators of the University of Missouri in September 1972. Dr. G. T. Stevens of the University's Rolla campus will be the principal investigator and will perform data …

An Intensity-Dependent Filter, James M. Thorne, Thomas R. Loree, George Mccall

Faculty Publications

It is useful in optically driven Kerr-cell shutters and other laser applications to have intense pulses with extremely low light levels between pulses. We describe here a device that accomplishes this objective external to the laser cavity.

The Theoretical Distribution Of Forces In The Rigid Component Of The Buccal Arch Positioner, Dennis H. Teruya

Loma Linda University Electronic Theses, Dissertations & Projects

The distribution of an applied force to the rigid component of the Buccal Arch Positioner was determined with a theoretically formulated model. The rigid component was assumed to be a free body without the semi-rigid attachments and was evaluated at four points for the force distribution. The summation of the forces and the moments were equated to zero and were utilized to derive equations to solve for the unknown forces. The unknown forces at each point of the rigid component were solved for in terms of the given force applications.

A laterally directed force application at one of the posterior …

Kinetic Modeling Study Of Catalytic Hydrogenation Of Codimer, William Mounce

Theses

A kinetic modeling study was made on a gas phase catalytic reaction. The data used was that on the hydrogenation of codimer, collected by Tschernitz, et al, The objective was to determine if non-linear least squares regression offers an advantage over linear least squares regression in discriminating between Langmuir. Hinshelwood kinetic equations.

For the experimental data in question, it was found that neither linear nor non-linear regression could distinguish between the two plausible mechanisms. With the particular mechanistic equations and range of data used in this study, the more laborious non-linear analysis offered no advantage over linear regression in discriminating …

Aboveground Fuel Oil Storage Tanks, Lawrence George Palmer

Theses

A review of the American Petroleum Institute Standard 650 and Appendixes points out the advantages of using high strength steel and the variable point design method (Appendix K) to obtain reasonably uniform shell stresses. Design limitations imposed by notch toughness and residual stresses are pointed out.

Design considerations for the installation of an internal floating roof in a standard cone roof tank are discussed. Methods of calculating evaporation losses and an economic justification for a floating roof are included. Budget estimate figures have been compiled as a function of tank capacity for tanks, site preparation and tank ringwall or piled …

Plastic Subassemblage Anlysis And Tests For Rigid High-Rise Steel Frames, J. Hartley Daniels, S. W. Kim

CCFSS Library (1939 - present)

No abstract provided.

Slope Stability Analysis: A Computerized Solution Of Bishop’S Simplified Method Of Slices, Steve M. Yoder, Tommy C. Hopkins

Kentucky Transportation Center Research Report

A computer program based on Bishop's simplified method of slices (1954) and capable of analyzing the slope stability of a multilayered soil mass is described. The computer program was specifically developed for analyzing the slope stability of highway bridge approach embankments; however, it can be applied to a broad spectrum of practical slope configurations and bearing capacity problems. Details of the use, applications, and accuracy of the program are presented. Important features of the computer program include a grid type, search operation for locating the critical shear surface and a ledger printout of the forces acting on each individual slice. …

Modification Of A Continuous Ice Crystal Replicator, Paul D. Thornley

Reports

A continuous ice-crystal replicator was modified by the addition of a gear drive to the cating wheel. This modification utilizes a positive drive force on the coating wheel rather than the friction force between the coating wheel and the film. The coating wheel operates successfully for at least 12 hours without slippage or damage to the film. Studies have uncovered several deficiencies in the replicator design which could be corrected. The correction of these deficiencies would lead to an improved quality of ice-crystal replicas. The need for continued studies in the fluid properties of Formvar solution is pointed out. Information …

A Streamflow Simulation Model For A Semi-Arid Region, Adnan A. Saad, L. Douglas James

Reports

A streamflow simulation model which would reproduce the essential feature of the hydrologic regime of a semi-arid region, in this case Jordan, was developmed and described. The model is intended to fit conditions which exist in such a region. The hydrologic processes components which represent the evaporation and the base flow distinguish the Jordan model from others. Development of each function of the model and its constants was based on all the minimal amount of data available. one year of data was used to calibrate the model for Wadi Zerqa watershed. The model was then applied to simualte four years …

Bibliography Of Latin American Agricultural Production And Development. Volume I: Inputs And Outputs In Crop And Livestock Production, Allen Lebaron, Samuel Daines, Percy Aitken, Ruby Johnson, Angeles Ely

Reports

No abstract provided.

Bibliography Of Latin American Agricultural Production And Development. Volume Ii: General Agricultural Planning, Background, And Statistical Studies, Allen Lebaron, Samuel Daines, Percy Aitken, Ruby Johnson, Angeles Ely

Reports

No abstract provided.