Digital Commons Network^™

Effects Of Subsurface-Drip-Irrigation On Alfalfa Evapotranspiration In The Intermountain West, Namuna Dhakal

All Graduate Theses and Dissertations, Fall 2023 to Present

Alfalfa is one of Utah’s most important crops, but it is also the largest agricultural consumer of water. Because the state faces frequent droughts and growing pressure on limited water supplies, farmers and water managers are increasingly interested in irrigation systems that could reduce water use. Subsurface drip irrigation (SDI), which delivers water directly to plant roots through buried drip lines, has shown promising results in other regions, where it often reduces water consumption and increases yield. However, little research has evaluated SDI under Utah’s unique climate, soils, and high-elevation valleys.

This study compared an SDI system with a traditional …

Comparison Of Consumptive Use Of Furrow And Drip Irrigated Onions, Chad C. Withers

All Graduate Theses and Dissertations, Fall 2023 to Present

The State of Utah funded agricultural water optimization studies to determine how agricultural water depletion can be decreased while maintaining or improving yields. Conversion from surface irrigation to drip irrigation is investigated as a method to decrease consumptive use.

Some Utah onion producers are converting from furrow irrigation to drip irrigation to decrease water and fertilizer use and improve profits. This study compares the consumptive use and yield of three drip irrigated onion fields against the consumptive use and yield of three furrow irrigated onion fields.

Arrays of soil moisture sensors at various depths were placed in drip and furrow …

Numerical Investigation On Lightning Survivability And Residual Strength Of Scarf-Patched And Z-Pinned Cfrp Composites, Logan Hales

All Graduate Theses and Dissertations, Fall 2023 to Present

Carbon fiber reinforced polymer (CFRP) composites are critical in aerospace applications yet remain vulnerable to lightning strikes due to orthotropic electrical conductivity and poor thermal resistance. Over the past decades, lightning-strike damage in pristine CFRP has been extensively investigated. However, the response of damaged and subsequently repaired laminates remains poorly understood, raising concerns about the structural integrity of repaired aircraft. This study aims to develop a sequentially coupled thermo-structural modeling framework to quantify how two common composite repair strategies (scarf patching and z-pinning), along with patch size, pin material, and configuration, influence lightning-induced damage and the residual flexural strength of …

An Investigation Of Data Granularity In Rag Pipelines For Personalized Medicine, Paritosh Pandey

Master's Theses

Generative AI, exemplified by large language models like the OpenAI GPT and Meta LLaMA families, can produce diverse content in response to prompts. This capability offers a promising solution to challenges in precision medicine, which seeks to tailor treatments to individual clinical profiles but often struggles with data collection, cost, and privacy concerns. By generating realistic, privacy-preserving patient data, generative AI has the potential to transform patient-centric healthcare. With such motivation, this research develops a comprehensive Generative AI pipeline emphasizing data granularity for accurate prediction of personalized treatments. The pipeline features a central Large Language Model interacting with a Machine …

Simulation Of A Buried Hydrogen Pipeline In Kansas State Soil, Sidney Hines

Master's Theses

Underground pipelines can be used to transport large amounts of pressurized hydrogen gas over several hundred kilometers. The design will be sensitive to the pipe material, diameter, and trench construction, and traffic loads above the pipe. The purpose of this paper is to conduct various geotechnical engineering analyses (seepage, stress, and slope stability) using the software program GeoStudio (version 2025.2.0) on a buried steel or FRP pipe section in a specific soil type, Harney Soil. Harney soil is of particular interest, because it is the Kansas State Soil and the analysis is for a buried gas pipe to run through …

Deep Learning For Predicting Impact Energy And Compression After Impact Strength Of Composite Materials Using C-Scan Images, K. T. Tan, Jason P. Mack, Faizan Mirza, Zhong-Hui Duan

University Research

Traditional assessment of post-impact performance in carbon fiber reinforced polymer (CFRP) composites often relies on simplified scalar metrics that fail to capture the complex spatial interactions driving failure. This study addresses this limitation by developing an automated, end-to-end deep learning framework that shifts from manual feature extraction to the direct interpretation of raw damage morphology from ultrasonic C-scans. Using a ResNet18-based convolutional neural network (CNN) trained on 1,428 augmented images, the model achieved coefficients of determination (R2) of 0.7948 ± 0.0847 for compression after impact (CAI) strength and 0.9436 ± 0.0098 for impact energy. Beyond prediction, this dual-purpose methodology serves …

Design And Evaluation Of A Single-Gate Multi-Threshold Null Convention Logic Architecture For Area Efficiency, John Edward Swaim

Graduate Theses and Dissertations

Asynchronous circuit design paradigms, such as NULL convention logic (NCL) and Multi-Threshold NCL (MTNCL), offer increased energy efficiency over synchronous equivalents and robust pipelines with minimal timing analysis. However, their dependency on dual-rail signal encoding causes significant overhead compared to single-rail equivalents. Previous single-gate and single-rail NCL paradigms have sought to reduce circuit area, but most compromise their quasi-delay-insensitivity and correct-by-construction nature with logic gate and system-level design choices. This thesis presents Single-Gate MTNCL (SG-MTNCL), a register controlled, single-gate, and dual-rail asynchronous architecture to improve the area efficiency of MTNCL without compromising the reliability of previous paradigms. The benefits of …

Faster Than The Speed Of Bram: In-Memory Computing For Next Generation Fpgas On The Edge, Nathaniel Joseph Fredricks

Graduate Theses and Dissertations

Traditional computer systems are hitting the Memory Wall as machine learning applications are bottlenecked by the bandwidth between separate memory and compute units. Current FPGA architectures are able to bypass this bottleneck with block RAMs (BRAMs) that provide on-chip, in-fabric storage. However, their potential as the foundation of computing components is often overlooked; machine learning accelerators implemented on FPGAs face additional delays when transferring data between memory and compute units. These penalties arise from BRAM bandwidth limitations and movement of data through the reconfigurable fabric. To support FPGA-based accelerators on the edge and break the Memory Wall, reconfigurable architectures must …

Design And Optimization To Advance Silicon Carbide Modules For Medium Voltage High Power Applications, Ahmed Ismail

Graduate Theses and Dissertations

The commercial availability of the first 10 kV silicon carbide (SiC) MOSFET removes the principal semiconductor barrier to medium-voltage power conversion, enabling converter topologies that are structurally inaccessible to silicon IGBT solutions at this voltage class. This dissertation presents the characterization infrastructure, device-level data, and preliminary system-level validation needed to advance the deployment of the third-generation 10 kV SiC MOSFET in converter applications. A custom-built 10 kV double-pulse test platform is developed with a fully documented component-sizing methodology, custom medium-voltage magnetics, and a measurement infrastructure capable of high bandwidth waveform capture at kilovolt common-mode potentials. On this platform, the third-generation …

Automated Circuit Design Algorithm And Implementation For Asynchronous Reset (Ares) Physically Unclonable Functions, Andrew Michael Felder

Graduate Theses and Dissertations

Technology is increasingly interwoven in all aspects of society as it solves new problems, creates new possibilities, and enables new conveniences. With its unceasing evolution, environments handling protected information such as military, finance, and medicine demand ever-evolving threat mitigation. Combating attackers’ abilities to spoof devices, uncover cryptographic keys, and bypass security features is a never-ending task which drives technological advancement to improve existing capabilities and develop entirely new methodologies. In this dissertation work, the hybrid Asynchronous RESet Physically Unclonable Function (ARES PUF) is evaluated at the circuit to determine its merits as a PUF. As part of this evaluation, results …

Study On The Effects Of Molecular Layer Deposition Coating And Mechanical Pressure On Lithium Metal Anodes, Cameron Mondl

Graduate Theses and Dissertations

Lithium (Li) metal is a highly promising anode material for next-generation energy storage systems due to its outstanding theoretical capacity and low electrochemical potential. However, its commercialization implementation has been hindered due to interfacial instability and uncontrollable dendrite formation, leading to poor cycling efficiency and thermal runaway. Among the most promising stabilization strategies, protective interfacial coatings have emerged as an effective solution to promote more uniform Li deposition and suppress erratic morphological inconsistencies. In particular, molecular layer deposition (MLD) enables uniform film thickness through layer-by-layer deposits, offering a highly versatile approach to protective interfacial layers. In addition to interfacial engineering, …

An Efficient Implementation Of Gibbs-Duhem Integration For Solid-Liquid Phase Coexistence In Binary Lennard-Jones System With Relevance To Aav Capsid Separation, Muhi Muntaka

Graduate Theses and Dissertations

Gene therapy using adeno-associated viruses (AAVs) holds promise for treating genetic diseases, but high manufacturing costs limit its widespread use. A major challenge is separating functional (full) AAV capsids from non-functional (empty) ones, which are produced in similar amounts and have nearly identical structures. Conventional purification methods, such as density gradient ultracentrifugation and chromatography, face drawbacks like low yield, poor scalability, and high cost, often requiring multi-step processes. Recently, selective crystallization has emerged as a promising alternative, offering improved efficiency, scalability, and product quality. However, optimizing this method requires a deep understanding of thermodynamic phase behavior in multicomponent systems. In …

Recovery And Evaluation Of A Germanium Infrared Camera, Michael Paszek

Graduate Theses and Dissertations

Short-wave infrared imagers made of germanium are a promising way to extend silicon-compatible imaging beyond the visible spectrum. They also use mature CMOS fabrication and readout electronics. This thesis details the recovery, initialization, and evaluation of a germanium focal plane array (FPA) infrared camera system using both a sealed TriWave camera and a modular prototype platform. Functionality was restored to this legacy hardware, and repeatable testing workflows were established for evaluating packaged infrared imagers under controlled indoor and outdoor conditions. The prototype used a custom software interface named Merlott for evaluation, and it followed a standard sequence that included checking …

The Effect Of Hydroflow Devices On Calcium Carbonate Buildup., Holton Shults

Master of Engineering Theses

Water containing high levels of dissolved minerals, mainly calcium and magnesium, is known as hard water, which is commonly found across the world due to calcium’s abundance in the earth’s crust. Hard water can lead to calcium carbonate buildup (also referred to as limescale) that reduces flow, clogs pipes, and lowers heat exchanger efficiency, all of which can drive up costs. This work evaluated two commercially available chemical-free treatment devices from HydroFLOW USA LLC, called the Pearl Plus and s38 devices. These electromagnetic devices are designed to alter calcium carbonate crystal structure, potentially reducing the amount of calcium …

Simultaneous Carrier, Cargo, And Functional Tracking Of Lipid Nanoparticles, Hannia Vanessa Balcorta Muñoz

Open Access Theses & Dissertations

Lipid nanoparticles (LNPs) have become effective delivery vehicles in nanomedicine, particularly for nucleic acid-based treatments. However, a major limitation remains in the field regarding the simultaneous monitoring of the nanoparticle carrier, its encapsulated payload, and the resulting functional protein production in both in vitro and in vivo systems. Furthermore, traditional lipophilic dyes employed for labeling LNPs frequently exhibit incompatibility with tissue-clearing methods, such as CLARITY, due to signal loss following lipid removal. This research developed and evaluated a new fluorescent labeling method using CM-DiI, a dye that reacts with thiols, for multimodal tracking of LNPs. CM-DiI was included in the …

Technology Based Assessment Of Workplace Biomechanical Risk: A Roadmap For Process Improvement, Tamer Adel Mohamed, Noha Mostafa, Ahmed Elsayed

Mechanical Engineering

The main objective of this paper is to develop a methodology for assessing the biomechanical risk in the workplace and design and apply improvements to reduce this risk by redesigning the working process. The risks are measured using Ergonomics tools to assess body posture and lifting index. Kinect sensor and video recordings are utilized to evaluate the joints' positions as an input for body posture data. Then, the specialized CATIA V5 software [26] is used to simulate the workers' bodies in the form of 3D models. Risk factors were assessed, and a new design was developed to be implemented in …

Comparative Experimental Analysis Of Vertical And Inclined Bifacial Pv Panels Under Varying Azimuthal Angles In Egypt For Agrivoltaics Systems, Ahmed Elbaz, Yahia Hassanein Nr, Iman Elmahallawi Dr, Tarek Abdelsalam Dr

Mechanical Engineering

The growing deployment of photovoltaic (PV) technologies across a wide range of applications, from residential rooftops to agrivoltaic systems, has created new opportunities, such as harnessing albedo from bright surroundings, as well as challenges, including limited space availability and adverse shading effects, which urge the need for optimising space along with energy use. While vertical bifacial photovoltaic (VBPV) systems may offer a potential solution, their effectiveness against their conventional inclined counterparts remains largely unexplored in different locations. This paper presents an experimental evaluation of the energy performance of vertical and inclined Bifacial PV configurations under the different climatic conditions of …

Extremum Seeking Compensation And Quantification Of Position Sensor Offset Error In Speed-Controlled Permanent Magnet Synchronous Motors, Tessa Biondo

Masters Theses

Position sensor offset errors present a persistent challenge in speed-controlled permanent magnet synchronous motor drives operating under field-oriented control. Even small, constant offsets in the measured rotor position can reduce torque effectiveness, requiring increased current and voltage demand to maintain the commanded speed and resulting in degraded speed regulation performance across a range of operating conditions. These effects are particularly problematic in speed-controlled systems, where speed loop dynamics cause increased electrical effort and limit overall performance. Many existing detection and compensation approaches are either dependent on the system model, require offline calibration, or are primarily designed for torque-controlled operation. This …

Transient Mitigation In Dual Active Bridge Converter Using An Auxiliary Converter With High-Frequency Selective Control For Load Step-Down Condition, Sachith Dilshan Wijesooriya

Masters Theses

Dual Active Bridge (DAB) converters are widely utilized in applications such as electric vehicles, renewable energy systems, and solid-state transformers due to their high efficiency, galvanic isolation, and bidirectional power transfer capability. However, during rapid load transitions, DAB converters frequently exhibit significant output voltage overshoot and prolonged settling times, which increase device stress and adversely affect system reliability. This thesis proposes an auxiliary-circuit-based transient mitigation method to address these limitations. The auxiliary circuit, implemented as a bidirectional Buck–Boost stage, operates in Boost mode during load step-down events to absorb excess energy and suppress the resulting voltage overshoot. The design of …

Assessment Of Lake Water Quality Parameters Using Uav Hyperspectral Imaging, Hasanul Banna, Taufiqa Tajnin

Publications and Research

Monitoring water quality in lakes is critical for assessing ecosystem health, managing drinking water resources, and detecting harmful algal blooms. Unmanned Aerial Vehicle (UAV)–based hyperspectral imaging provides a promising approach for high-resolution observation of water quality parameters. In this undergraduate research project, hyperspectral imagery collected over sample lakes within the Delaware River Watershed was processed using BaySpec’s CubeStitcher software to assess its capability to detect variations in chlorophyll-a (Chl-a) concentrations. This work was conducted as part of a National Fish and Wildlife Foundation (NFWF)-funded project in collaboration with Princeton Hydro and NYC College of New York. Hyperspectral image cubes were …

Dynamic Load Assessment Of Pem Fuel Cell Systems Under Pid-Based Control Strategies For Sustainable Operation, Tarek Abedin, Paw, Normy Norfiza Abdul Razak, Chen Chai Phing, Yaw Chong Tak, Monowar Mahmud, Manzoore Elahi M. Soudagar, T. M. Yunus Khan, Mohammad Tariqul Islam, Mohammad Nur-E-Alam

Research outputs 2022 to 2026

Proton exchange membrane fuel cell (PEMFC) systems’ reliable operation under variable load conditions is a significant challenge because of voltage fluctuations, transient variations, and the high computational requirements of sophisticated control techniques like intelligent and model predictive controllers. Even while these state-of-the-art methods provide great precision, complexity and cost often limit their real-time applicability, underscoring the need for a simpler but efficient control solution. To achieve effective voltage regulation in PEMFC systems, this study suggests a DC–DC buck converter in conjunction with a comparator-based proportional–integral–derivative (PID) control technique. In order to provide stable operation under both constant and changing load …

Engineered Uio-66-Nh2 Hybrid Nanocomposites For Antifouling Ultrafiltration Membranes With Dual Resistance To Microplastics And Protein Fouling, Mitra Golgoli, Mohadeseh Najafi, Javad Farahbakhsh, Masoumeh Zargar

Research outputs 2022 to 2026

The growing presence of microplastics (MPs) in water and their impact on ultrafiltration (UF) membranes during the early stages of wastewater treatment highlight the need for effective mitigation strategies. This study explores the innovative modification of UF membranes by incorporating various hybrid metal-organic frameworks (MOFs) nanoparticles, including UiO-66-NH2 hybrids with multi-walled carbon nanotubes (MWCNTs) (UiOM), chitosan (UiOC), and sulfobetaine zwitterions (UiOZ). These nanoparticles were synthesized and integrated into innovative UF membranes to compare their performance on MPs fouling effect in particular. The integration enhanced membrane hydrophilicity and altered surface roughness, creating a hydrophilic functional network that improved water permeability. Water …

Comparative Fatigue Analysis Of Cf-Pla Metamaterial Bone Plates For Orthopaedic Fixation, Ani Daniel, Hamed Bakhtiari, Barun K. Das, Muhammad Aamir, Majid Tolouei-Rad

Research outputs 2022 to 2026

Bone plates are widely used in orthopaedic surgery to stabilise fractured bones and support healing following traumatic injuries or osteotomies. However, conventional metallic bone plates suffer from stress shielding and stiffness mismatch with bone, which can hinder optimal healing. Additive manufacturing enables the incorporation of novel metamaterial architectures into polymer-based implants to enhance mechanical properties. The fatigue behaviour of these implants during the healing period is critical to ensuring their structural integrity and long-term performance. In this study, the compressive fatigue performance of fused deposition modelling (FDM)-printed carbon fibre-reinforced polylactic acid (CF-PLA) bone plates were investigated. Four metamaterial structures—tetrachiral, re-entrant, …

Thermo-Hydro-Chemical Coupled Numerical Modeling Of Hydrogen-Thermal Co-Development In Hydraulically Fractured Peridotite, Jiacheng Dai, Zhonglin Ma, Yunzhi Yue, Yujie Yuan, Shouceng Tian

Research outputs 2022 to 2026

Hydrogen generation through serpentinization reactions in peridotite formations under high temperature conditions represents a promising avenue for subsurface hydrogen production. However, the thermal energy in the formation environment have not been sufficiently considered. To integrate hydrogen production with thermal energy development, this study develops a thermo-hydro-chemical coupled numerical model, which is used to investigate hydrogen-thermal co-development in hydraulically fractured peridotite. Given that the hydrogen-thermal co-development process involves fluid flow, heat transfer and serpentinization reactions, the governing equations are formulated based on Darcy flow and energy conservation equations, with serpentinization kinetics incorporated through the reactive source terms. To evaluate hydrogen production …

A Systems Engineering-Based Method For Enabling Digital Transformation In A Binational Small Healthcare Enterprise, Manuel Adrian Alvarez Ramirez

Open Access Theses & Dissertations

The year 2020, often described as "the great accelerator" for emerging technologies, marked a period of significant transformation in lifestyles, work patterns, and business strategies. For instance, online meetings have become more convenient than in-person interactions, even with colleagues in neighboring offices. For small businesses, rapid regulatory and technological changes required swift adaptation, including the acquisition of new technologies, tools, and software to ensure survival. This transition also necessitated adopting indirect engagement, revising communication protocols, and digitally transforming information. Small and Medium-sized Enterprises (SMEs) in essential service sectors face also a fundamental paradox: their dependence on the skills, relationships, and …

Development Of A Simulation-Driven Evaluation System For Foreign Objects In Aircraft Structures, Daniela Garcia

Open Access Theses & Dissertations

This thesis investigates the use of simulation-driven methods to evaluate the behavior and potential impact of foreign objects within aircraft structures. Foreign Object Damage (FOD) remains a major concern in aerospace safety, as small components unintentionally left inside aircraft compartments can create uncertainty regarding their effect during flight. Although current inspection methods can detect the presence of foreign objects (FOs), they often cannot determine whether these objects pose a significant structural risk, leading to conservative maintenance decisions. To address this limitation, this work develops a simulation-based framework that integrates Computational Fluid Dynamics (CFD) and Finite Element Analysis (FEA) to evaluate …

Influence Of Nickel Content On Microstructural Evolution And Densification Of Tungsten Fabricated Via Vat Photopolymerization, Jose Miguel Gonzalez

Open Access Theses & Dissertations

Hybrid additive manufacturing of tungsten-nickel alloys, combining vat photopolymerization (VPP) for patterning with custom thermo-hydrogen post-processing for reduction and densification, has emerged as a promising route for fabricating complex, high-resolution tungsten architectures. However, fabrication of tungsten via this hybrid AM technique remains challenging due to poor densification and significant defect formation during debinding and sintering. In this work, these limitations were addressed using nickel as a sintering aid in combination with controlled thermal processing conditions. Existing studies on activated sintering of tungsten typically focus on a single composition or sintering condition, limiting understanding of the combined effects of composition and …

Ai-Based Framework For Elucidating The Ring Opening Energy Of Cycloalkanes, Evan Griffin

Open Access Theses & Dissertations

Cycloalkanes are a prominent component of jet fuels due to their high volumetric energy density and lower soot yield compared to aromatics. However, the structural nuance of cycloalkanes can make predicting their combustion kinetics challenging. The present study aims to develop a quantitative structure-property relationship of the ring opening energy (ROE) of cycloalkanes. A total of 253 cycloalkanes were curated from the ZINC15 database, ranging from monocycloalkanes to tetra-cycloalkanes. The 3-D cartesian coordinates of the closed shell and open shell diradical states for all curated cycloalkanes was generated with RDKit in Python and used MMFF94 to optimize the molecular geometries. …

Additively Manufactured Grx-810 Alloy: The Influence Of Build Interruptions Onmicrostructure, Tensile Strength And Fatigue Life., Javier Eduardo Lares Monarrez

Open Access Theses & Dissertations

This study investigates the influence of build interruption on the microstructure, microhardness, tensile behavior, and fatigue performance of laser powder-bed fusion (LP-BF) specimens in both the as-built and heat-treated conditions using the GRX-810 alloy. The heat treated condition incorporated Hot Isostatic Pressing (HIP), and both interrupted and uninterrupted samples were evaluated to isolate the effects of processing variables. Results indicate that build interruption did not produce significant changes in yield strength, ultimate tensile strength, or ductility, suggesting that the LP-BF process is robust enough to tolerate controlled interruptions without compromising bulk mechanical integrity. Microhardness measurements and microstructural observations further supported …

Quantifying Spatiotemporal Ev In-Motion Load Dynamics For Flexible Distribution Grid Operations, Travis Newbolt

Open Access Theses & Dissertations

The emergence of novel in-motion Electric Vehicle (EV) charging through Dynamic Wireless Power Transfer (DWPT) technology is enabling the transformation of traditional roadway infrastructures into fully integrated Electrified Transportation Networks (ETNs) by the direct coupling of roadways with electric power grids. This paradigm has the potential to improve charging safety, extend driving ranges, reduce EV manufacturing costs through smaller battery sizes, and shift EV charging demand to periods when Distributed Energy Resources (DERs) are more readily available. In addition, the transition to ETNs can improve air quality and reduce noise pollution by displacing fossil fuel consumption from vehicles to centralized …