Digital Commons Network^™

Component Residential Building Construction, Gary L. Trickey

Graduate Research Papers

To study residential component building as one of the first steps towards a more industrialized method of home construction.

Response Of Orthotropic Bridge Decks To Highway Loadings, Harry Morris Rexin

Dissertations and Theses

This thesis documents the fabrication, testing techniques, and response of a plastic scale model of an orthotropic bridge deck. To economically investigate a two-lane steel bridge deck, plastic Acrylic^R was used as a modeling material. Welds were simulated with dichloromethane, a capillary action solvent, and PS-30, a polymerizable cement. Deflections were measured with laboratory dial guages while strains were monitored with strain guages mounted on the deck.

The response of the deck to AASHO vehicle axle loads was compared with a discrete element computer program used to analyze orthotropic bridge decks continuous over flexible supports. Results indicate good correlation …

Problems Of Measurement In The Environmental Field, Harold M. Cota

Civil and Environmental Engineering

No abstract provided.

Effects Of High Altitude Jet Aircraft On The Stratosphere, Dennis K. Bushnell

Retrospective Theses and Dissertations

This paper presents a review of the basic thermal, chemical and radiation balances existing in the atmosphere and discusses the mechanisms by which jet engine exhaust products can disturb these balances. Possible effects of stratospheric pollution on plant and animal life are discussed. Methods for reducing harmful emissions through engine design modifications are outlined and current successful research programs are surveyed. The SST type aircraft is shown to be a greater threat to the environment than conventional jets because of differences in cruise altitudes. It is concluded that due to the existence of several potential environmental problems associated with contamination …

Remote Sensing Of Earth Resources System Capabilities V.S. Design Constraints, William Howard Grisham

Retrospective Theses and Dissertations

There is new evidence that global earth resources satellite net will be practical. This paper weighs recent advances in remote sensing to pinpoint the dominant constraints. The data and sensor systems interfacing requirements are critically reviewed. It is shown that conventional optics constraints can be relaxed, with the newer systems, based on multi-spectral imagery and statistical processing methods. The most powerful computational methods use algorithms based on a Gaussian assumption for the species vector in feature space, but biases in the imagery limit their efficiency. A rationale is proposed: improving the observational network calibrating efficiency will also improve the photogrammetric …

Generalized Feedback Shift Register Pseudorandom Number Algorithm, Theodore Gyle Lewis, W. H. Payne

Electrical and Computer Engineering Faculty Research & Creative Works

The generalized feedback shift register pseudorandom number algorithm has several advantages over all other pseudorandom number generators. These advantages are: (1) it produces multidimensional pseudorandom numbers; (2) it has an arbitrarily long period independent of the word size of the computer on which it is implemented; (3) it is faster than other pseudorandom number generators; (4) the "same" floating-point pseudorandom number sequence is obtained on any machine, that is, the high order mantissa bits of each pseudorandom number agree on all machines— examples are given for IBM 360, Sperry-Rand-Univac 1108, Control Data 6000, and Hewlett-Packard 2100 series computers; (5) it …

A Simulation Modeling Approach To Central City Dynamics, Leonard William Schaper Jr.

Dissertations

This dissertation describes a computer simulation model of a central city with emphasis on its application to Newark, New Jersey. The work begins with a review of the Forrester Urban Dynamics Model; the first attempt to simulate the entire system of the city. The objections to this model which have appeared in the literature are discussed, and the model is viewed in the light of other work in the field. A set of guidelines to aid the "second generation" model building effort is developed. The actual construction of a model which attempts to follow these guidelines is described. First, the …

The Quantitative Characterization Of Middle Distillate Fuels For Reduced Smoke Emission And Improved Low Temperature Operability, R. S. Feamster

Theses

Forty-eight inference equations are presented to approximate the hydrocarbon composition of middle distillate fuels and of the solids separating from these fuels at temperatures below their cloud points by consideration of fuel physical inspections. The physical inspections consist of API gravity, aniline point, cloud point, and distillation curves for ten fuels from major United States and European refineries. To determine the percentage of solids separating from cooled fuels, each fuel is filtered over a temperature range from the cloud point to -40 F in 10 F increments. Aromatic, naphthenic, and paraffinic hydrocarbon contents and the r-paraffin carbon number distributions of …

Velocity Distribution Versus Sediment In The Missouri River, Glendon Taylor Stevens, Terence E. Harbaugh, Paul R. Munger

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Analysis of the large quantities of velocity and sediment data gathered on the Missouri River has not been undertaken in the past due to the heavy workloads of U.S. Army Corps of Engineers staff. The need to undertake this effort has long been recognized by both the Kansas City District and the Omaha Division. As a result of this need, the Kansas City District, Corps of Engineers, entered into a contract with the curators of the University of Missouri in September 1972. Dr. G. T. Stevens of the University's Rolla campus will be the principal investigator and will perform data …

The Photolysis Of Chlorobenzene In An Aqueous Environment, Louis John Del Tufo

Theses

Chlorobenzene was chosen as a model system for the study of photochemically induced reactions in an aqueous environment. It was the goal of this research to achieve a reaction system which best approximates conditions existing in the environment. To do this, a basic model system was established, and then the effect on the rate by various parameters was studied. These parameters, which included the presence of oxygen and such inorganic compounds as might be present in receiving waters, (e.g. nitrate, sulfate, and phosphate), were chosen so as to meet the goal of this research.

Kinetic data was obtained for seven …

Computer Simulation Of A Split Feed Claus Sulfur Recovery Plant, Thomas R. Woolley

Theses

A computer program which calculates a complete heat and material balance around a "split feed" Claus sulfur recovery plant was written in Fortran IV for the RCA Spectra 70 computer. The program provides for up to three catalytic reactors, the hot gas bypass method of reheating, and a feed gas containing hydrogen sulfide, water vapor, hydrogen, and nitrogen. The program user specifies as input data the feed stream composition and temperature, the number of reactors, the combustion air temperature, the conversion in each reactor, the outlet temperature in each condenser, and the fraction of burner exit gas used for reheating …

Automotive Emission Control, Thomas P. Schultz

Graduate Research Papers

Emission control systems required by the federal government to reduce exhaust, crankcase, and fuel system emissions a.re resulting in engines that have a. totally new set of fundamental characteristics. This paper is intended to examine the various emission control systems and attempt to gain insight into their effect on engine performance, economy, service and trouble shooting techniques that will make servicing these engines more effective.

The Theoretical Distribution Of Forces In The Rigid Component Of The Buccal Arch Positioner, Dennis H. Teruya

Loma Linda University Electronic Theses, Dissertations & Projects

The distribution of an applied force to the rigid component of the Buccal Arch Positioner was determined with a theoretically formulated model. The rigid component was assumed to be a free body without the semi-rigid attachments and was evaluated at four points for the force distribution. The summation of the forces and the moments were equated to zero and were utilized to derive equations to solve for the unknown forces. The unknown forces at each point of the rigid component were solved for in terms of the given force applications.

A laterally directed force application at one of the posterior …

A Method Of Analyzing Mandibular Movement, Richard B. Mccoy

Loma Linda University Electronic Theses, Dissertations & Projects

Mandibular movement is considered to be a fundamental factor in the study, analysis, and treatment of occlusion. For many years, dentists have realized that dental health depends upon the compatibility of mandibular movements and occlusion. This realization has led to the development of new methods and techniques for recording accurately and scientifically the movements of the mandible. In order for this data to be of scientific value, it must be stored in a usable form which is easily available for analysis.

The purpose of this research project was to develop a procedure for storing and recalling mandibular-movement information. Before such …

Jacksonville Urban Area Transportation Study: Annual Certification And Unified Work Program For The Jacksonville Urban Area, Jacksonville Area Planning Board

Arthur N. Sollee, Sr. Textual Materials

Document contains committee activities, surveillance findings, short range multi-modal implementation program, unified work program and suggested funding sources.

Interfacial Energy And Wettability Of Some Glass-Metal Systems, Mahmoud Yehia Demeri

Archived Theses and Dissertations

No abstract provided.

Aboveground Fuel Oil Storage Tanks, Lawrence George Palmer

Theses

A review of the American Petroleum Institute Standard 650 and Appendixes points out the advantages of using high strength steel and the variable point design method (Appendix K) to obtain reasonably uniform shell stresses. Design limitations imposed by notch toughness and residual stresses are pointed out.

Design considerations for the installation of an internal floating roof in a standard cone roof tank are discussed. Methods of calculating evaporation losses and an economic justification for a floating roof are included. Budget estimate figures have been compiled as a function of tank capacity for tanks, site preparation and tank ringwall or piled …

A Study Into The Feasibility Of Constructing A Pedestrian Mall In Newark Downtown, Stephen Wesley Warren

Theses

Newark's central business district has been suffering steady economic decline for at least a decade. In an attempt to halt this trend, and perhaps even reverse it, a feasibility study has been conducted toward the goal of implementing a pedestrian mall in the area.

This study was accomplished by conducting both field examinations of Halsey Street, the area under consideration, and investigating data from other existing United States pedestrian malls.

The results of this study show that it is feasible to construct a permanent pedestrian mall on Halsey Street and that the benefits of doing so far outweigh the costs …

Separation Of Glucose - Fructose - Water Systems Via Thermal Parametric Pumping, Zikri Mostafa Ahmed

Theses

Series of experiments were carried out to determine the effect of different factors on adsorption from aqueous solutions of sugar using fuller's earth ( LW 16-30 Mesh ) as an adsorbent. The equilibrium data were fitted to the Langmuir's equation., and an explanation for the deviation of some of these data has been given.

Systems of glucose-fructose and water mixtures were subjected to semi-continuous and continuous parametric pumping operations using activated carbon (400 Filterasorb) as an adsorbent. The results obtained confirm the equilibrium theory of the parametric pump and essentially fulfill the requirements established by Chen and Hill (6) to …

Digital Computer Solution Of Electromagnetic Transients In Large Power Systems, Bijan Navidbakhsh

Dissertations and Theses

This thesis is an introduction to the solution of electromagnetic transients by a combination of the Bergeran method of characteristics and the application of trapezoidal rule of integration.

Three test examples solved by digital computer illustrate the step by step solution and computer programming.

To compare this method with the Laplace transformation technique, a test problem solved by both methods and also digital computer is illustrated. In conclusion, the advantages and disadvantages of both methods are compared.

Air Pressures Over Reservoir, Canal, And Water Catchment Surfaces Exposed To Wind, Allen Ray Dedrick

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

Surface air pressure differentials that occur over reservoirs, canals, and water-catchment aprons in high-wind conditions were determined by the use of models in a wind tunnel. Such information was needed concerning the magnitude and location of destructive wind forces on water barriers constructed of exposed flexible membrane liners. Rigid models, without a membrane, were used to measure airpressure differentials.

Air-pressure differentials were dependent on geometric configuration and were independent of viccous forces above the critical Reynolds number which was determined experimentally. The geometric factors studied with respect to reservoirs and canals included approach slope, approach slope length, leeward slope, and …

A Hydrologic Model Of The Provo River Basin, Utah, Craig T. Jones

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

The purpose of this paper is to develop a general hydrologic model for use on a digital computer and prove its validity by applying it to a management study of the Provo River Basin. Hydrologic equations have been proposed for each major hydrologic occurrence within a river basin. By linking these equations through restrictions on continuity of mass, a general hydrologic model can be obtained. Such a model becomes the basic tool for studying the management of the river basin hydrology. The paper describes the model components, parameter identification program, and the river basin management program.

High-Intensity Reflective Materials For Signs, Rolands L. Rizenbergs

Kentucky Transportation Center Research Report

Field observations and laboratory tests and evaluations were conducted on High-Intensity and Engineering grade materials (Scotchlite), manufactured by the Minnesota Mining and Manufacturing Company, and were compared in regard to reflectivity, durability, and cost.

The High-Intensity type materials were found to have outstanding performance characteristics in comparison to Engineering Grade materials. The material significantly enhances sign legibility under low-beam illumination, and accelerated weathering tests showed superior durability.

Pavement Roughness, Measurement And Evaluation, Rolands L. Rizenbergs, James L. Burchett, Larry E. Davis

Kentucky Transportation Center Research Report

Vertical accelerations of a passenger in an automobile are automatically summed while traveling a section of road at 51.5 mph (23.0 m/s). A roughness index is obtained by dividing this sum by the time elapsed during the test. Continuity in measurements since 1957 has been preserved through correlations among successive vehicles involved and reference pavements.

In general, bituminous construction has yielded smoother-riding surfaces than concrete construction. The smoothness of concrete pavements, however, has improved on those projects where slip-form paving was used. Interstate and parkway (expressway) construction continues to yield smoother pavements than other major construction. The rate of increase …

Engineering Geognosy Of The Western Coal Field, W. Mccann, Tommy C. Hopkins, Robert C. Deen

Kentucky Transportation Center Research Report

Engineering soils and geologic reports are invaluable tools for engineers, industrial leaders, community planners and administrators during preliminary stages of planning and site selection for construction projects. Such information can be used to great advantage by planners in making soil and geologic reconnaissance surveys, in organizing and checking field surveys, in correlating and predicting performances of soil and geologic materials, and in locating construction materials and resource deposits. Recognizing the need for this type of information, the Division of Research, Bureau of Highways, Kentucky Department of Transportation, has undertaken a study to report the engineering geognosy of Kentucky. The report …

Tartan Surfacing For An Equestrian Overpass, Donald C. Newberry Jr.

Kentucky Transportation Center Research Report

The location of I 64 in Jefferson County traverses Seneca Park, noted for its scenic beauty and superior recreational facilities. A bridle path in Seneca Park necessitated construction of an overpass for equine traffic. A non-slip and sound-deadening, resilient surface was essential for aesthetics and safety. Tartan, a rubbery mat developed primarily for race course and paddock surfaces, was specified and installed on the overpass.

Long-Term Retention Of Tritium In Man, Chin-Jen Ou

Electronic Theses and Dissertations

[No abstract provided.]

A College Level Helicopter Curriculum, Eugene B. Krueger

Undergraduate Theses and Senior Projects

No abstract provided.

Current Design Practice For Bridge Superstructures Connected To Flexible Superstructures, Jack H. Emanuel, J. Leroy Hulsey, John Best, Joseph H. Senne, Leroy E. Thompson

CCFSS Library (1939 - present)

No abstract provided.

The Formation And Properties Of Machining Burrs, Laroux K. Gillespie

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

The formation of burrs in Machining Operations occurs by three Basic Mechanisms:

1) Lateral Extrusion of material

2) Bending of the chip

3) Tearing of the chip form the workpiece

Each of these mechanisms has been studied analytically and compared to experimental results. The agreement between predictions and measurements has been found to be close.

Drilling, milling, grinding, and turning burrs were produced in 303Se stainless steel and their properties were related to tool geometry, feedrates, and depth of cut. One thousand measurements were made and subsequently analyzed by analysis of variance techniques. The properties measured include burr length and …