Digital Commons Network^™

Laminar Heat Transfer For Small Prandtl Number Fluids Including Step Change In Wall Temperature, Shiny Ting

Masters Theses

"The object of this investigation is to provide a simple means of determining the heat transfer from a flat plate which has an unheated leading length x₀. The case of steady, two-dimensional, laminar flow of an incompressible fluid with a Prandtl number of less than one is considered. Since there exists an unheated length and the Prandtl number of the fluid is less than one, the thermal boundary layer intersects the flow boundary layer. Thus, the solution of the problem divides into two regions. In this study, the problem is solved analytically by employing the energy integral equation. The temperature …

Compressibility Effects On Transient Gas Pipe Flow, Gerald Francis Mouser

Masters Theses

"Abstract (1) Methods of iterative solution for the partial-differential equations that govern the transient flow of gases in pipelines are obtained by using the method of characteristics and linear finite-difference techniques. Solutions are developed for 1) a constant gas compressibility factor throughout transient conditions, and 2) a variable gas compressibility factor at constant temperature dependent upon pressures encountered during transient flow. Theoretical studies are made to compare results using both approaches for pipelines operating at various constant flowing temperatures. Results show greater differences between the two methods at lower values of flowing temperature due to the more rapidly changing compressibility …

An Investigation Of A Bistable Oscillator Used In A Phase Modulated Control Circuit, Yu-Fang Yen

Masters Theses

"A primary component in the investigation of phase modulated control systems is bistable oscillator which converts a constant oscillation signal to control the system. The oscillator is feedback type that utilizes a feedback capacitance and resistance in each feedback path to change its frequency. The theoretical behavior of bistable oscillator was investigated and the non-dimensional results were set for convenience in determining the oscillation period. The control circuit which based on the oscillator was also presented a form of suitable circuit for direct application to practical control problems"--Abstract, page ii.

Development Of An Elastic-Plastic Finite Element Program With The Initial Strain Approach, Vernon Dale Allen

Masters Theses

"A finite element method is presented for solution of plane stress and axisymmetric elastic-plastic problems employing the method of successive elastic solutions with the initial strain approach. The problem of nonconvergence of the initial strain approach for perfectly plastic problems was eliminated by expressing the Prandtl-Ruess equations entirely in terms of strain. Two examples are presented to demonstrate the validity of the method"--Abstract, page ii.

High Temperature Compressive Creep In Mullite, Peter C. Smith

Masters Theses

"Compressive creep measurements were made on two groups of mullites at temperatures between 1455ºC and 1520ºC. The first group consisted of commercially manufactured mullites. The second group was made up of 7 different mullite compositions spanning the alumina-silica solid solution range from 3Al₂O₃ • 2SiO₂ to 2Al₂O₃ • SiO₂ . Thermal activation energies and stress exponents were calculated for the mullites in the second group. Steady state strain rates taken at 1460ºC under loads of 100 and 110 psi varied between 1.3x10⁻⁴ in/in/hr and 15.4x10⁻⁴ in/in/hr. Activation energies were between 109 Kcal/mole and 204 Kcal/mole. Stress exponents calculated from data …

Use Of The Turbulence Kinetic Energy Equation In Analyzing Turbulent Near Wakes, James Edward Auiler

Doctoral Dissertations

"A general method is presented for analyzing turbulent flow fields in the near wake regions of two-dimensional and axisymmetric bodies. The governing partial differential equations of continuity, momentum and turbulence kinetic energy are expressed in elliptic form in terms of the dependent variables stream function, vorticity and turbulence kinetic energy. An iterative finite-difference technique is used to solve the governing equations simultaneously. Numerical solutions are obtained for the following physical problems: 1. Laminar near wake: Only stream function and vorticity are considered for laminar flow. Solutions are compared with available analytical results for uniform flow over a sphere. 2. Turbulent …

Dynamic Behavior Of Eccentrically Stiffened Plates, Charles Stuart Ferrell

Doctoral Dissertations

"The dynamic behavior of eccentrically stiffened rectangular plates is studied by the finite element method. The addition of stiffeners to a plate structure is a common method of increasing the rigidity of the structure with a minimum of weight increase. However, this stiffened plate configuration does not easily lend itself to analysis. This study is an approach to finding a rational method by which the dynamic behavior of such a stiffened plate structure may be determined. The governing differential equations for the finite element model are derived and the stiffness and mass matrices for the plate and stiffener elements are …

Identification Of Linear Systems With Delay Via A Learning Model, Hugh Francis Spence

Doctoral Dissertations

"The effects of input delay on an identification scheme using a learning model are investigated. The parameter adjustment laws for the learning model are derived through Lyapunov methods similar to those used for the model reference adaptive control systems of Parks. For no measurement noise or delay mismatch between the learning model and system, the parameters are adjusted to bring the error between model and plant to zero. When there is delay mismatch between the inputs of the learning model and the unknown system, the convergence of the parameters of the learning model to those of the unknown system is …

Test 1070: Minneapolis-Moline A4t-1600 Diesel (Also Oliver 1655 Diesel) 10-Speed, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF TEST REPORT

GENERAL CONDITIONS

East tractor is a production model equipped for common usage. Power consuming accessories can be disconnected only when it is convenient for the operator to do so in practice. Additional weight can be added as ballast if the manufacturer regularly supplies it for sale. The static tire loads and the inflation pressures muse conform to recommendations in the Tire Standards published by the Society of Automotive Engineers.

PREPARATION FOR PERFORMANCE RUNS

The engine crank case is drained and refilled with a measured amount of new oil conforming to specifications in the operator’s manual. The …

The Effect Of Channel Errors In The Differential Pulse-Code-Modulation Transmission Of Sampled Imagery, Roger J. Arguello, Harvey R. Sellner, John A. Stuller

Electrical and Computer Engineering Faculty Research & Creative Works

This Paper Presents an Analysis, Simulation, and Discussion of the Effects of Communication Errors on Four-Bit Differential Pulse-Code Modulation (DPCM) Sampled Imagery. Simulations Are Presented that Describe the Effects of Inserting Periodic "PCM Updates" in Order to Correct Communication Errors in the DPCM Transmission of Photographic Scenes that Have Been Scanned and Sampled at the Nyquist Rate. Copyright © 1971 by the Institute of Electrical and Electronics Engineers, Inc.

Electrical Engineering Education In An Industrial Laboratory, J. Derald Morgan

Electrical and Computer Engineering Faculty Research & Creative Works

This paper describes a unique electrical engineering laboratory course. This laboratory is an example of industry-uni-versity cooperation in engineering education. The organization and operation of the course is outlined and explained. The educational benefits derived from such cooperation between industry and the university are briefly detailed. These benefits are extended to the students, the university, the faculty, and the participating industry. This paper provides the framework and challenge to industry from which other laboratory experiences can be conceived and developed. Copyright © 1971 by The Institute of Electrical and Electronics Engineers, Inc.

Water Conservation Handbook, D J. Carder, G. W. Spencer

Natural resources published reports

This handbook is intended as a practical guide in some of the most common aspects of water conservation in the agricultural areas of Western Australia. It deals mainly with water conserved in dams for stock and domestic purposes on the farm.

the farm. The handbook does not attempt to deal with all aspects of handling and using water for agricultural purposes. This is a vast subject which extends into many fields such as engineering, irrigation and land use.

The guide does, however, touch on some important aspects of good management of agricultural land. It should be read in conjunction with …

Test 1084: John Deere 2030, Nebraska Tractor Test Lab

Nebraska Tractor Tests

No abstract provided.

Test 1068: Case 970 Power Shift Diesel, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF TEST REPORT

GENERAL CONDITIONS

East tractor is a production model equipped for common usage. Power consuming accessories can be disconnected only when it is convenient for the operator to do so in practice. Additional weight can be added as ballast if the manufacturer regularly supplies it for sale. The static tire loads and the inflation pressures muse conform to recommendations in the Tire Standards published by the Society of Automotive Engineers.

PREPARATION FOR PERFORMANCE RUNS

The engine crank case is drained and refilled with a measured amount of new oil conforming to specifications in the operator’s manual. The …

Test 1076: Case 870 Power Shift Diesel, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF TEST REPORT

GENERAL CONDITIONS

East tractor is a production model equipped for common usage. Power consuming accessories can be disconnected only when it is convenient for the operator to do so in practice. Additional weight can be added as ballast if the manufacturer regularly supplies it for sale. The static tire loads and the inflation pressures muse conform to recommendations in the Tire Standards published by the Society of Automotive Engineers.

PREPARATION FOR PERFORMANCE RUNS

The engine crank case is drained and refilled with a measured amount of new oil conforming to specifications in the operator’s manual. The …

Test 1079: Steiger Bearcat Diesel 10-Speed, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF TEST REPORT

GENERAL CONDITIONS

East tractor is a production model equipped for common usage. Power consuming accessories can be disconnected only when it is convenient for the operator to do so in practice. Additional weight can be added as ballast if the manufacturer regularly supplies it for sale. The static tire loads and the inflation pressures muse conform to recommendations in the Tire Standards published by the Society of Automotive Engineers.

PREPARATION FOR PERFORMANCE RUNS

The engine crank case is drained and refilled with a measured amount of new oil conforming to specifications in the operator’s manual. The …

Test 1080: International Farmall 1466 Turbo Diesel, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF TEST REPORT

GENERAL CONDITIONS

East tractor is a production model equipped for common usage. Power consuming accessories can be disconnected only when it is convenient for the operator to do so in practice. Additional weight can be added as ballast if the manufacturer regularly supplies it for sale. The static tire loads and the inflation pressures muse conform to recommendations in the Tire Standards published by the Society of Automotive Engineers.

PREPARATION FOR PERFORMANCE RUNS

The engine crank case is drained and refilled with a measured amount of new oil conforming to specifications in the operator’s manual. The …

Test 1086: Massey-Ferguson Mf 1500 Diesel, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF TEST REPORT

GENERAL CONDITIONS

East tractor is a production model equipped for common usage. Power consuming accessories can be disconnected only when it is convenient for the operator to do so in practice. Additional weight can be added as ballast if the manufacturer regularly supplies it for sale. The static tire loads and the inflation pressures muse conform to recommendations in the Tire Standards published by the Society of Automotive Engineers.

PREPARATION FOR PERFORMANCE RUNS

The engine crank case is drained and refilled with a measured amount of new oil conforming to specifications in the operator’s manual. The …

Test 1088: Case 770 Manual Diesel 8-Speed (Chassis Sn 8675001 And Up), Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF TEST REPORT

GENERAL CONDITIONS

East tractor is a production model equipped for common usage. Power consuming accessories can be disconnected only when it is convenient for the operator to do so in practice. Additional weight can be added as ballast if the manufacturer regularly supplies it for sale. The static tire loads and the inflation pressures muse conform to recommendations in the Tire Standards published by the Society of Automotive Engineers.

PREPARATION FOR PERFORMANCE RUNS

The engine crank case is drained and refilled with a measured amount of new oil conforming to specifications in the operator’s manual. The …

Anodic Dissolution Of Beryllium In Anhydrous Media, William Joseph James, Martin E. Straumanis

Chemistry Faculty Research & Creative Works

No abstract provided.

Mass Transfer Inside Liquid Droplets And Gas Bubbles Accompanied By A Second‐Order Chemical Reaction, R. J. Brunson, Robert M. Wellek

Chemical and Biochemical Engineering Faculty Research & Creative Works

No abstract provided.

Clay Cover For Roaded Catchments, J L. Frith, R. A. Nulsen

Journal of the Department of Agriculture, Western Australia, Series 4

RECENT dry years have stimulated interest in improved catchments for farm dams. Although roaded catchments have been installed on many farm dams in Western Australia, most of them fall short of their potential for increasing run-off.

Permeability Scaling In A Numerical Coning Model, V. K. Dutta, Marion D. Arnold

Geosciences and Geological and Petroleum Engineering Faculty Research & Creative Works

A method is described for simulating coning into a wellbore using a numerical simulation model. The method allows the wellbore cells to be considerably larger than the actual wellbore. This makes coning studies feasible using an implicit pressure-explicit saturation type model with a reasonable time step. This capability is achieved by scaling the horizontal-vertical permeability ratios to give the proper vertical potential drop.

Perturbation And Sensitivity Analysis Of An Urban Model, Nicola Ann Nelson

Masters Theses

"This work describes a sensitivity analysis of the nine major system variables of the urban model postulated by Dr. Jay W. Forrester in his book Urban Dynamics. This model simulates the growth of a city from a nearly empty land area through a 250 year life cycle. Using small perturbations about the system trajectories, sensitivity matrices were computed at 135 years (growth period) and 240 years (equilibrium). The results show a matrix heavily weighted to give large sensitivity coefficients to the three housing variables, the PH sector being the most sensitive. Each of the housing sectors was analyzed further to …

Laser Interferometric Holography Investigation Of Free Convection About A Vertical Plate Of Non-Uniform Temperature, Richard Kenneth Thomson

Masters Theses

"An experimental investigation was conducted using a holographic interferometer to detect the temperature variation in a free convection boundary layer about a vertical heated plate. The heated plate was non-isothermal and investigations were conducted for four temperature distributions; the maximum plate temperature ranged from 200F to 493F. Photographs were taken of the fringe patterns and boundary layer thickness measurements, as well as temperature measurements, were made. A theoretical model was constructed by applying the integral method to the energy and momentum equations. The experimental values agree quite well with this model. The advantages of the holographic interferometer over other systems …

Design And Preliminary Testing Of A Thermomechanical Rock Fragmentation Apparatus, Gary Earl Fenton

Masters Theses

"The design characteristics of equipment to thermally weaken and mechanically fragment hard rock were developed and the apparatus constructed. An initial investigation of thermo-mechanical fragmentation was conducted on Missouri red granite. The particles from the fragmentation tests were sized and this analysis was used in the Rittinger theory to calculate surface area breakage energy. It was found that the application of thermal energy could reduce the surface area breakage energy per unit volume of material removed by as much as 41 percent. The use of kerfs in the rock increased the amount of material removed and permitted larger particles to …

A Triangular Element For Numerical Solutions Of Axisymmetric Conduction Problems In Cylindrical Coordinates, Prafulla Chandra Mahata

Masters Theses

"The triangular element is one of the many suitable elements which are used in finite difference methods as applied to conduction heat transfer. Such elements find many applications in conduction problems in Cartesian coordinates. This work proposes a new triangular element for axisymmetric conduction problems in cylindrical coordinates. The validity and workability of the networks formed by the proposed triangular elements are strengthened by selected examples. The work is completed by the application of the triangular element to an industrial problem having irregular boundaries. The results are compared with the solution obtained by the finite element method"--Abstract, page ii.

Shop Level Maintenance Of Inertial Platforms Without A Surveyed Site, Max E. Bott

Masters Theses

"The initial installation of a rotary tilt table for an aircraft inertial navigation system test facility includes accurately aligning the rotary tilt table to local level and true north coordinates. The survey techniques presently employed are an encumbrance during installation and complicate remote deployment. The objective of this thesis is to determine if an inertial platform or platforms can practically be used to replace the role of the survey techniques in the rotary tilt table alignment. The construction, capability and operation of a rotary tilt table are reviewed. The tests necessary to test and calibrate an inertial platform are outlined, …

Triangular Signal Stabilization Of Nonlinear Systems, Kamaleddin Yadavar Nikravesh

Masters Theses

"Many nonlinear systems display self-sustained oscillations which are often undesirable. The stabilizing effect of a high frequency input signal on an oscillating system with one nonlinearity is determined by the characteristics of the nonlinear element in the system, the linear portion of the system and the amplitude of the signal. This investigation has been concerned with the effect of a triangular wave stabilizing signal on these self oscillations. The equivalent gains for several common nonlinearities are derived. The pseudo describing function introduced by Oldenburger and Boyer for sinusoidal stabilization has been extended to the triangular wave case, and it is …

An Experimental Determination Of The Effect Of The Axisymmetric Turbulent Wake On The Pressure Distribution On A Sphere, Martin Gardner Bowin

Masters Theses

"A study of the effect of the turbulent wake of a water drop on the motion of a smaller droplet is essential in order to gain an understanding of the behavior associated with the collision coalescence phenomena. The use of spheres of macroscopic size proves to be a valuable method in observing these effects. This experimental investigation centers on (1) a check on the validity of the instrumented sphere as a device to measure normal static pressure, and (2) the study of the effect of the turbulent wake of the test model sphere upon the instrumented sphere. Measurements were made …