Digital Commons Network^™

Fluid Flow In Pipes Of Rectangular Cross Sections, Bruce Harold Bradford

Masters Theses

"Head loss due to fluid friction was measured in smooth conduits of rectangular cross section. The data covers the laminar and turbulent range. Results were compared with previous theoretical and empirical data.

The customary practice of calculating head loss in non-circular conduits by use of the friction factor obtained on an “equivalent” circular pipe was discussed. It was found that this practice is successful in square cross sections undergoing turbulent flow. In laminar flow, however, this method is not accurate"--Abstract, page ii.

An Ac Method Of Measuring The Conductivity Of Dielectric Liquids., Henry E. Fischer

Masters Theses

"The problem undertaken in this thesis is the presentation of a method of measuring the conductivity of dielectric liquids in which the liquid is used as the parallel tank circuit of a modified Wien-bridge oscillator. The main advantage of this method is that the frequency of the voltage applied to the liquid can be varied by simply varying the oscillator frequency. This allows the selection of a frequency which is best suited to the liquid in regard to polarization and relaxation time.

An oscillator was designed, built and used in the laboratory to measure the conductivity of the dielectric liquids …

The Irish Plumbing And Heating Engineer, November 1965 (Complete Issue)

Building Services Engineering

No abstract provided.

Torsional-Flexural Buckling Of Thin-Walled Open Sections, Pen J. Fang, George Winter

CCFSS Library (1939 - present)

INTRODUCTION Compression members with thin-walled open sections, because of their low torsional rigidities and because their cross-sectional configuration is such that the centroid and the shear center often do not coincide, can buckle at loads well below the Euler load by interaction of torsion and bending. Fast expanding applications of such sections in civil and architectural engineering call for an extensive investigation of torsional-flexural buckling. Basic theory of torsional-flexural buckling is treated by a number of authors, I,2 and simplifications of the basic theory in the elastic range for the design purposes together with some test results were reported previously. …

Strength Of Three New Types Of Composite Beams, A. A. Toprac

CCFSS Library (1939 - present)

No abstract provided.

Drag Forces On Magnetically Accelerated Particles, Darrell Winterton Walker

Theses and Dissertations

The object of this investigation was to determine the effect of acceleration on the drag of spheres as it differs from the steady state case. Steady state drag applies to the force acting on a single sphere moving at constant velocity through an infinite, continuous, incompressible, turbulence free fluid. Extensive experimentation has quite thoroughly documented the steady state drag characteristics of spheres. A dimensionless parameter associated with the drag force is sometimes used to correlate drag characteristics.

Torsional-Flexural Buckling Of Thin-Walled Open Sections, Pen J. Fang

CCFSS Library (1939 - present)

No abstract provided.

Turbulent Flow In The Entry Region, Chin-Hsiu Li

Theses and Dissertations

When entering into the subject of turbulent flow, it is essential to understand that the kind of flow with which we deal belongs to a particular class known as shear flow. These types of flow comprise flow fields in which relative velocities have been induced by shear stresses rather than by the action of pressure forces. In pipe flow, when the fluid enters through the well-rounded bell from a reservoir or from the calm open air, a uniform velocity distribution occurs at the pipe entrance. Immediately down stream from the entrance of the pipe, the flow is structured with a …

Investigation Of The Octene-Decane-Urea Adduct Equilibrium System, Frederick Charles Guest

Theses

Concentrations of equilibrium mixtures formed by adding increments of octene to a solution of urea in methanol to form adduct are reported.

Calorimetric studies indicate that the addition of octene to a urea-methanol solution shows an endothermic heat effect prior to the formation of solid adduct. The heat effect becomes exothermic as solid adduct is formed.

Addition of decane to an equilibrium octene-urea adduct system increased octene concentration in the supernatent liquid, indicating an octene release from the original adduct as decane adduct was formed.

The order in which decane and octene were added to form the decane-octene-urea adduct system …

Cation Exchange Between Solutions Of Ferric Nitrate And Dowex 50x-8 Resin, Michael H. Mansky

Theses

The rate of exchange of ferric ions from solutions of ferric nitrate and hydrogen ions from Dowex 50X-8 has been studied in an agitated bed ion exchange column over a range of bed loading conditions. Agitation has been maintained in a regime known to indicate film diffusion control of rate in small scale batch reactors.

Calculated diffusion coefficients for the column are slightly higher than those determined in the batch reactor because of greater turbulence of agitation in the column.

The assumption of previous investigators concerning linearity of equilibrium data has been found to be invalid for the system studied. …

The Thermal Conductivity With Vapor Pressure For N-Paraffin Hydrocarbons, Jacob Tolsma

Theses

A literature search of the thermal conductivity of pure liquids has been made and experimental values have been compiled. Study of the theory of the thermal conductivity of liquids indicated that a relationship exists between thermal conductivity and viscosity. Previous investigations have found an almost linear relationship between the logarithms of viscosity and vapor pressure for n-paraffin hydrocarbons. In this investigation the logarithm of thermal conductivity plotted versus the logarithm of vapor pressure for the same series was also found to be almost linear. The equation of the line when combined with a linearized Antoine equation in terms of the …

An Investigation Of The Need To Correlate Academic Subject Areas With Industrial Arts, Ernest James Boedcher

Graduate Student Research Papers

This study was initiated as a result of a need that became apparent in two industrial arts seminars at Central Washington State College. Studies reveal that industrial arts teachers use principles, laws, and applications of mathematics and science daily, but these are seldom recognized and made meaningful to the students. As a result of this study industrial arts teachers may see a way to use this material to initiate similar situations in their teaching.

Planning And Scheduling Software Programs With Pert, Henry E. Mielo

Theses

The use of the Program Evaluation and Review Technique (PERT) in planning and scheduling software programs was discussed in this thesis. A real world program, referred to as the Wrap-Around Simulation or WAS Project, was selected to illustrate that complex efforts in the software domain can respond favorably to modern planning and scheduling techniques

The WAS Project included the provision of a digital simulation of the shipboard environment in which a Digital Fire Control Computer (DFCC) would operate as part of a Digital Fire Control System. The digital simulation afforded a well controlled and conclusive checkout of the operational program …

Tests Of A Suggested Piezometric Method For Determining Hydraulic Conductivity Of Saturated Soils, K. R. Channarasappa

All Graduate Plan B and other Reports, Spring 1920 to Spring 2023

A major factor in the design of drainage systems is the hydraulic conductivity of the soil strata to be drained. Various methods for measuring the hydraulic conductivity of soils in both the field and the laboratory have been devised. In many cases, however, laboratory methods fail to give reliable data since the natural field conditions under which flow actually takes place cannot be duplicated in the laboratory. Hence a need exists for a field method for measuring hydraulic conductivity of soils in situ. When a large number of tests are to be performed in a given location, a simple, quick, …

The Irish Plumbing And Heating Engineer, April 1965 (Complete Issue)

Building Services Engineering

No abstract provided.

The Irish Plumbing And Heating Engineer, February 1965 (Complete Issue)

Building Services Engineering

No abstract provided.

Sharpening And Care Of Mulesing Shears, A L. Jones

Journal of the Department of Agriculture, Western Australia, Series 4

THIS year will probably see more sheep mulesed in Western Australia than ever before.

It is not surprising, therefore, that some improvements have been made to the standard mulesing shears.

New modified shears make mulesing easier —but they must be properly sharpened.

Lot Feeding Of Beef Cattle. 1. Introduction, W J O Wilkie

Journal of the Department of Agriculture, Western Australia, Series 4

"LOT FEEDING" of cattle is the name given to the operation of bringing cattle in from pasture and giving them the total ration they are to receive in open or partly roofed yards.

The roof would be intended to protect the feed trough and not the cattle.

Milking Machine Efficiency And Shed Husbandry Practices, G R. Olney

Journal of the Department of Agriculture, Western Australia, Series 4

MILKING machine efficiency on dairy farms in the Bridgetown, Greenbushes, Balingup, Boyup Brook and Nannup areas was the subject of a recent testing survey.

During the survey 106 machines were tested and the results assessed statistically to gauge the general level of machine efficiency in these districts.

Water Vapor Measurements Using Infrared Absorption, Duard S. Woffinden

Reports

Man’s attempt to control the amount of available water has taken two approaches, i.e., weather modification and water storage through the use of man-made reservoirs. In either case, it is necessary to ascertain the water vapor content of the atmosphere. In the case of weather modification, if the water vapor content is insufficient, it is futile to attempt to start precipitation. In the case of reservoirs, it is important to know the evaporation rate since it has been demonstrated that some reservoirs provide a net negative contribution to the total water supply by increasing the normal evaporation losses. Any attempt …

The New Yilgarn Vermin Fence, Department Of Agriculture, Western Australia

Journal of the Department of Agriculture, Western Australia, Series 4

THE State's vermin fence system, forming a barrier between the outer edges of the agricultural areas and the pastoral areas, has been extended 162 miles with the completion of the Yilgarn Vermin Fence this year.

Fence Out Those Rabbits, J C. Rowbotham

Journal of the Department of Agriculture, Western Australia, Series 4

THERE is probably no more distressing sight to orchardists' eyes than two or three hundred young fruit trees that have been damaged by rabbits.

Detection Of Stress Corrosion Cracking In U-Bend Brass Specimens By An Electro-Mechanical Method, Floyd Elwin Loftin

Masters Theses

"An apparatus was designed and built which held two u-bend specimens. When the specimens were exposed to a corrodent, losses in strength were detected as a result of stress corrosion cracking. The apparatus was used to study time to failure of cartridge brass u-bend specimens exposed to ammoniacal copper sulfate solutions which varied in pH. A minimum time to failure, 1.06 hours, was detected at pH 7.2. The maximum time to failure, for the range studied, was 28.36 hours at pH 7.7.

No useful data were obtained in the range from pH 6.6 - 6.8. thick, black surface coatings were …

Thin Film Resistor Deposition, Rollie R. Herzog

Masters Theses

"Thin film techniques may be the key to future miniaturization of electrical equipment. The purpose of this thesis was to develop procedures for deposition of thin film resistors and to test these deposited resistors. Starting with a vacuum system, equipment was designed and built to hold and heat the substrate, monitor the substrate temperature and deposited resistance, and to evaporate the material to be deposited. Resistors were deposited and tested for resistance between resistors, capacitance between resistors, and resistance of resistors. A heat aging test was also used comparing resistors with and without a silicon monoxide coating"--Abstract, page ii.

The Eccentric Orifice As A Flow Measuring Device In Small Diameter Pipes, James E. Casale

Masters Theses

"This thesis reports and evaluates the use of an eccentrically placed orifice as a flow measuring device in small pipe sizes. The orifice is placed in a concentric location and moved to increasingly eccentric locations until full eccentricity is reached. At full eccentricity the circumference of the orifice is tangent to the circumference of the pipe. The effects of increasing eccentricity are evaluated for four orifices...Flow coefficients for the orifices in different locations are plotted against Reynolds numbers. The eccentric orifice is a reliable, accurate flow measuring device for metering or controlling the flow of fluids. Design criteria can be …

Measurement Of Stray Load Loss Of D.C. Machines, Kanaiyalal Ramanlal Shah

Masters Theses

"For many years the standard practice, in calculation of conventional efficiency of d.c. machines, has been to include stray load losses as equal to 1% of the output. This assumption may be true for large, compensated d.c. machines but it is known to be small for smaller, uncompensated, general-purpose, industrial-type machines of open design. An A.I.E.E. Committee on Rotating Machines was formed to investigate whether the present practice of assigning 1% for the stray load loss is justified or not. They reached a conclusion, reported in 1949, after investigating 243 stray loss tests on different motors ranging from 1/2 hp …

Turbulence In Journal Bearings, Kashyap R. Mehta

Masters Theses

"In this investigation, an experimental study was performed on a journal bearing under laminar and turbulent flow conditions. Using relationships for friction factor developed previously by other investigators a comparison was made with results of this present investigation. Since the flow changes from laminar to turbulent with a change in speed of rotation, curves for friction factor as a function of speed were plotted. Various attempts to make the recording and measuring systems more sensitive were also made and are discussed in this thesis"--Abstract, page ii.

Warping And Curling Of Plain Concrete Slabs, Vipinbhai Ratilal Shah

Masters Theses

"The study was made to determine the effect of daily atmospheric temperature variation and curing on the warping and curling of plain concrete slabs and to study the effect of moisture on the warping of plain concrete slabs under nearly constant temperature conditions, by keeping the bottom surface of one slab wet and the other dry.

Daily observations consisted of dial gage readings to determine the progressive variations in warping contours due to typical daily temperature curling. Trends were found for three months of dial gage readings and interpreted in terms of warping and curling of the slabs.

The warping …

Buckling Strength Of Titanium Alloy Columns In The Elastic And Inelastic Range, Richard O. Rintoul

Masters Theses

"The purpose of this study is to find experimentally the buckling strength of titanium alloy (Ti.-6Al.-4V.) columns and to determine a suitable equation to be used in the design of titanium columns in the elastic and inelastic range.

Effective length over radius of gyration ratios of from 178 to 16.1 were studied. High strength steel plates with cylindrical radii milled in the faces served as column ends while cylindrical radii ends were milled on the columns. SR-4 strain gages were used at the mid-points of all columns to determine lateral deflection and predict a theoretical buckling stress. Actual column loads …

Matching Of A Horn Antenna To Its Dense Surrounding Media By The Use Of Artificial Dielectric Methods, Paul Arthur Ray

Masters Theses

"The purpose of this thesis is to design an artificial dielectric slug to match a horn in a media such as water and to discuss a method of determining experimentally its dielectric properties. The design is based on known artificial dielectric methods. The method of determining the dielectric properties is by microwave waveguide reflection techniques. This thesis deals with the theoretical aspects and suggests an experimental method of determining the practicability of such a matching method"--Abstract, page ii.