Digital Commons Network^™

Passive Wireless Corrosion And Temperature Detection In High-Temperature Environments, Noah Lane Strader

Graduate Theses, Dissertations, and Problem Reports (ETD)

This work focuses on the theory and development of LC sensors for high temperature and corrosion measurement for stainless steel and copper surfaces with power industry and general corrosion detection applications. The LC resonators were fabricated via screen printing an Ag inductor on an alumina substrate. The LC design was modeled using the ANSYS HFSS modeling package. The LC passive wireless sensors operate with resonant frequencies centered at 85-110 MHz. The wireless response of the LC sensor was interrogated and received by a radio frequency signal generator and spectrum analyzer at temperatures from 50-800 °C for copper ground planes and …

Transparent And Conductive Gallium Oxide Electrode For Simultaneous Recording And Optogenetic Stimulation, Christopher Patrick Carey

Graduate Theses, Dissertations, and Problem Reports (ETD)

Neural electrode technology has been around for centuries since the times of Galvani. In early electrophysiology experiments metal wires were used to induce contractions in dissected animals. The metal wire electrode has since been a standard tool to both stimulate and record neural activity. In the past two decades, a new strategy for neural stimulation has been formulated based on the emergent field of optogenetics. Optogenetics refers to the use of light-sensitive proteins genetically imbedded in the membrane of a neuron to elicit neural activity. This technique offers more selectivity in the stimulation of neurons. Typical optogenetic neural electrodes, or …

A Mixed Methods Approach To Evaluation And Modeling Of Ergonomic Stressors Due To Mass Decedent Handling, Vaishakhi Suresh

Graduate Theses, Dissertations, and Problem Reports (ETD)

Work-related injuries, illnesses, and musculoskeletal disorders (MSDs) significantly impact the U.S. healthcare industry, leading to lost working days, high medical costs, and increased turnover rates among healthcare workers (HCWs). Increased physical and mental health risks due to the handling of deceased during COVID-19 pandemic has exacerbated these issues. While the ergonomic risks of patient handling are well-studied, limited research exists on the ergonomic risks of manual handling of the deceased. Therefore, the primary objective of this study was to explore the challenges associated with decedent handling so that effective safety interventions to reduce the risk of injury and mental distress …

4d Epr Oximetry Imaging For 4d Bioprinting And Tissue Engineering, Sajad Sarvari

Graduate Theses, Dissertations, and Problem Reports (ETD)

Bioprinting, akin to 3D printing, employs cell-laden hydrogels such as GelMA (Gelatine Methacrylate) and Alginate instead of plastic or resin to create biological structures. The printing process followed by subsequent tissue maturation is known as 4D bioprinting, where the fourth dimension is time. Ensuring adequate and consistent oxygen, O2, supply within 3D bioprint volume over the entire maturation period process is crucial, as even transient hypoxia can impact cellular behavior and phenotypes. However, printing of fully developed vasculature remains an unresolved technical challenge. Several approaches to chemically (peroxides) or biologically (photosynthesis) generate oxygen during bioprint maturation have been proposed. However, …

Far-Field Passive Wireless Sensors Composed Of Electroceramic Materials For Harsh Environment Applications, Kevin M. Tennant

Graduate Theses, Dissertations, and Problem Reports (ETD)

The demand for high temperature sensing technologies in industrial applications has been steadily increasing, driven by the need for precise monitoring and control in extreme environments. This thesis presents an investigation into the development and optimization of passive wireless sensors for high temperature sensing applications. The research focuses on overcoming the challenges associated with traditional sensing methods by leveraging passive wireless sensor technology, offering advantages such as reduced complexity, improved reliability, and enhanced flexibility.

A passive wireless high temperature sensor for far-field applications was developed for stable temperature sensing up to 1000 °C. The goal is to leverage the properties …

Evaluating The Impact Of Ergonomic Interventions On Reducing Knee Musculoskeletal Disorder Risks During Residential Roof Shingle Installation: A Phase-Level Analysis, Nazia Zerin

Graduate Theses, Dissertations, and Problem Reports (ETD)

The prevalence of knee musculoskeletal disorders (MSDs) among roofers due to awkward kneeling postures during shingle installation is a well-recognized concern. While knee-saving interventions like knee savers (KSs) and knee pads (KPs) have shown the potential to reduce MSD risks, their effectiveness across different phases of shingle installation remains unknown. The objective of this study is to assess how interventions of KSs and KPs alleviate the risks of MSDs in the knees during various phases of shingle installation. These phases include (1) reaching for shingles, (2) placing shingles, (3) grabbing a nail gun, (4) moving to the first nailing position, …

Cleaning And Characterization Of Chemical Vapor Deposited Graphene For Nanoelectronic Device Development, Sakib Ishraq

Graduate Theses, Dissertations, and Problem Reports (ETD)

Nanoelectronic devices based on graphene are a promising technology that combines the sensitivity and specificity of ion and element recognition with the accuracy and precision of electronics. The detection principle is based on the interaction of the target molecules with the nanodevice surface, which generates a measurable electrical signal. In the current study, graphene and its derivatives, synthesis and fabrication of high quality, good uniformity, and low defects graphene have been investigated as they are critical for high-performance and highly sensitive devices. Among many synthesis methods, chemical vapor deposition (CVD), have been used that needs to be transferred from the …

Guardians Of The Catheters, Interprofessional Collaboration Reduced Cauti Rates At Phfh, Dawn Doud, Angela Shemwell, Stephanie Brown, Tobi Bryan, Georgia Gauron, Tasha Anisimov, Peter Weitzman, Emma Peterson, Tiffanie Rampley

Articles, Abstracts, and Reports

Abstract Title: A Quality Improvement Project to Reduce CAUTIs on Inpatient Units

Objectives:

1. Participants will be able to understand how interprofessional collaboration contributed to CAUTI reduction on inpatient acute care units.
2. Participants will be able to understand education nurses completed to reduce CAUTI rates on inpatient acute care units.

Purpose/Aims:

To reduce CAUTI rates for adult inpatients admitted to the acute care units: Progressive Care Unit (PCU), Surgical/Orthopedics, Medical/Oncology, and the Intensive Care Unit (ICU).

Background

An increase in CAUTI rates for adults admitted to inpatient units was identified in January of 2024. The CAUTI rate at that time was …

Mechanical Reliability Of Aerosol Jet Printed Sensors And Interconnects, Lemuel A. Duncan

Browse all Theses and Dissertations

Heterogeneous integration (HI) is currently being investigated to maintain the pace of technological progress in the electronics industry. With the recent acceleration witnessed in additive manufacturing (AM) technology, interest has been expressed in introducing aerosol jet (AJ) printing to the fabrication process for sensors and electronic packages. Integrating AM technology in these areas promises design flexibility and minimal material waste. Three AJ printed applications investigated in this work include strain sensors, electrical interconnects, and metal embedded chip assemblies. Before moving forward with the use of AJ printing in these applications, it is necessary to evaluate their performance under standard mechanical …

Integrating Knowledge Graphs With Large Language Models For Natural Language Querying, Rakesh Kandula

Browse all Theses and Dissertations

This research explores the integration of knowledge graphs with large language models that have already been trained on a vast pool of unstructured text data. Large language models trained on this type of data have a tendency to hallucinate and produce factually inaccurate results. This behavior is primarily due to the data being trained is unstructured and huge text corpus, and large language model uses predictive text analysis methods to obtain a response. These issues can be addressed by applying Retrieval Augmented Generation and Fine-tuning to large language models, employing an underlying domainspecific knowledge graph. Integrating knowledge graph and large …

Prediction Interpretations Of Ensemble Models In Chronic Kidney Disease Using Explainable Ai, K M Tawsik Jawad

Browse all Theses and Dissertations

Chronic Kidney Disease (CKD) poses significant health and financial threat to millions of patients all around the world. The irreversible nature of this disease not just leads to comorbid diseases like Diabetes Mellitus, Hypertension, Anemia, Bone Disease, Neurological Implants etc. It can permanently damage the kidney by progressing to Acute Kidney Injury (AKI) or End Stage Renal Diseases (ESRD). The risk factors of CKD become more dangerous as patients suffering from it have little to no idea about the presence of CKD in their body until it takes the shape of AKI or ESRD. There are severe economic burdens for …

Stanley Black And Decker Slag Removal Design Project, Colt Hemphill, Kyle Stober, Andrew Raymond, Robert Artrip

Williams Honors College, Honors Research Projects

My group given the task of designing a system to remove the slag of large metal plates. Removing this slag is an important step in creating the final assembly of a model. Currently we the operators are flipping the plates using a large magnet and crane. The issue that we see with the current method is the risk of injury while having the plate suspended in the air. These plates can reach upwards of 600lbs and poses a serious threat to the operators if the magnet is not secured correctly. Our new system for removing the slag is designed to …

Infant Molds For Cleft Deformities, Hannah Brunow, Drew Reinbolt, Rhonda Troyer, Christian Miller

Williams Honors College, Honors Research Projects

Cleft lip and palate are very common birth defects where the roof of a baby's mouth and lip do not form properly while in the womb. Babies born with cleft lip or palate can undergo surgery after going through a process to make the initial gap smaller through incrementally smaller, retainer-like appliances. We will be trying to find a way to improve the pre-surgery process by implementing 3D printing. We will be performing this research for a craniofacial orthodontist at Akron Children's Hospital. We hope that our success will lead to a decrease in the amount of time spent making …

Children's Hospital Animatronic, Erin Keller, Wesley Cunningham, Dylan Mueller, Carl Richter

Williams Honors College, Honors Research Projects

This senior project explores the development of a pediatric-oriented animatronic designed to enhance the hospital experience for children. Recognizing the importance of alleviating the anxiety and fear that often accompany hospital visits, the project focuses on creating an engaging and interactive companion to soothe children.

Key components of this project include:

1. Creative Design: The animatronic character's design prioritizes child-friendliness, employing research into child psychology and preferences to ensure an appealing and approachable aesthetic.

2. Electrical and Mechanical Engineering: A robust mechanical and electronic system was engineered to enable lifelike movements, gestures, and responses.

3. Interactive Features: A simple, user-friendly app will be …

   ---

   Go to article

Yankee Manufacturing Multi-Assembly Pvc-Gasket Assembly Mechanism, Lily Coss, Jessica Kun, Dana Chapin, Jenan Hasan

Williams Honors College, Honors Research Projects

This project focuses on designing and implementing an efficient mechanism to connect PVC and gasket pieces in the door assembly process at Yankee Manufacturing. The aim is to improve process efficiency and productivity by increasing the assembly rate from 130 to 195 assemblies per hour, a 38% improvement. The project involved research, design iterations, performance evaluations, and adherence to engineering codes and standards, particularly focused on safety, ergonomics, and sustainability. The design process includes addressing challenges from a previous attempt, redefining project scope, and incorporating new elements such as transitioning to the packaging process seamlessly. Ethical considerations include promoting operator …

Effects Of Energy Drink Additives On Crayfish Metabolism, Katherine Paltz

Williams Honors College, Honors Research Projects

The effects of caffeine and additives commonly found in energy drinks were tested on crayfish to record changes, if any, in their metabolism. Three experimental groups were studied: 1. Caffeine; 2. Caffeine + Glucuronolactone; 3.) Caffeine + Glucuronolactone + Taurine. Caffeine is a common stimulant used to improve mental awareness, headaches, memory, and athletic performance. Glucuronolactone is connected with cardiovascular issues and aggressive behavior. Taurine is said to improve mood and focus. The experiment was performed at two different caffeine levels: 600mg and 1200mg for an initial 1 hour of exposure and 10 hours after exposure used as a pseudo-baseline. …

Self-Watering Plant Device, Nick Sabetta

Williams Honors College, Honors Research Projects

Many homeowners enjoy having plants around their homes. However, life can quickly become busy and stressful. This often makes it difficult to keep with their house plants. The goal of this project is to design a device that will be able to help take care of house plants. The device will be able to water the plant when the soil moisture is detected. The device will also monitor the air temperature as well as the sunlight levels that the plant is receiving. All of the collected data will then be sent via Bluetooth to a smartphone. The app will alert …

Assessing Industry-Critical Skill Development In Engineering Technology Capstone Courses, Rustin Webster, Matthew Turner

School of Engineering Technology Faculty Publications

To meet industrial expectations, engineering and engineering technology (ET) graduates are expected to possess the critical competencies of design, problem-solving, communication, and teamwork. However, industry stakeholders and academic studies routinely identify these as skills gaps: areas graduates need to develop to a higher standard or are currently lacking when entering the work force. To address this issue, many undergraduate programs in the United States have implemented a comprehensive and integrative experience at the end of an academic program, often called a capstone course(s). The rate of adoption has grown such that approximately three-quarters of all undergraduate and graduate institutions include …

Implementing Integrated Stem Forensic And Soil Sciences Lab Activities To Promote Interest In Stem Careers, Mariah K. Stollar Awan, Caroline J. Rakowski

Indiana STEM Education Conference

We implemented forensic and soil science integrated STEM lab activities with 11 middle school youth at a 4-H day camp at Purdue University. STEM perceived knowledge increased overall for participants. However, the pre- and post-assessments did not show a statistically significant difference. More students also indicated STEM career interest after participating. Because this study was exploratory and had a small sample size, more research on these integrated STEM lab activities should be conducted with larger samples.

Course-Based Undergraduate Research Experiences (Cure) In Engineering Technology, Bill Hutzel, Craig Zywicki, Stephanie M. Gardner

School of Mechanical Engineering Faculty Publications

Although most universities provide excellent research experiences for outstanding undergraduate students, the number of interested students typically outstrips the supply of faculty and graduate student mentors. Addressing this shortfall is the reason Course-based Undergraduate Research Experiences (CUREs) were created. CUREs face obvious challenges because they operate at a larger scale than the traditional apprentice-based model for undergraduate research, creating resource issues for experimental research that requires equipment, laboratory space, and staff oversight. To help address these hurdles, one university has created a professional development program that provides training, collegial mentoring, and financial support to interested faculty. This paper provides an …

Smart Dog Door, Andrew Shetler, William Boissoneault, Jacob Stump, Benjamin Charlson

Williams Honors College, Honors Research Projects

With modern life getting busier and more complex, many have turned to autonomous assistance for taking care of pets. The objective of this project is to design and prototype a device and application that will allow only certain dogs to enter and exit through a dog door while making the owners aware of their dog's activity. The dog door will utilize wireless communication from the dog to the door to control the status of the door’s lock and update the database that will send updates to the application. The application will keep track of when the dog enters and exits …

Battery Dunnage, Paul Hirsch, Alex Cox, Ben Strubbe

Williams Honors College, Honors Research Projects

Schaeffler is launching a new assembly line for a battery in 2025. As part of the project, it is necessary to design and fabricate a reusable dunnage (packaging) specialized for the battery, meant for safe domestic transportation in the United States. Through an iterative process, the team developed a final dunnage design out of steel components that had a maximum footprint of 62 in X 43.5 in X 29.25 in and a weight of 821.682 lbs. The dunnage is stackable on itself up to two high, weighing a total of 4,918.724 lbs. when loaded with four batteries. The design was …

Degradable Staples And Delivery Device, Meha Elango, Jessica Cabrera, Makayla Scarpitti, Kareemat Melaiye

Williams Honors College, Honors Research Projects

The scope of this project is to design a method to secure skin grafts to healthy tissue. The ultimate goal for the proposed method is to be dissolvable in some form. Currently, skin grafts procedures utilize staples in most cases to hold a skin graft in place, but there are disadvantages that come with it. Staples are easy to place, but time consuming during the removal procedure. They also cause a lot of pain and discomfort for the patient. The goal of this project is to determine a way a secure skin grafts to healthy skin in order to reduce …

3d Printed Drone (Body And Controls), Michael Dick, Hayden Pinkelman, Tanner Henderson, Logan Prince

Williams Honors College, Honors Research Projects

The objective is to build a scaled down model of a 3D printed drone capable of carrying a payload scalable to 50 lbs. for a wide array of applications. Some applications of the drone could include delivering support materials during natural disasters, such as foam to put out fire or medical aid packs to provide aid to injured people, food or package delivery, or military applications. The project has been split up into two groups. One group will be focusing on the propulsion aspect of the project, such as the electric motors and airfoil. Simultaneously, this group will design the …

Custom Mobility Aid - Exoskeleton, Jenna Rentsch, Mackenzie Yu, Perry Antalek, Joseph Wisniewski

Williams Honors College, Honors Research Projects

Injuries to the spinal cord can cause major mobility deficits, paralysis, and even death. Our client is an adult male who has suffered fractures to the C4 and C5 vertebrae resulting in partial nerve damage and loss of mobility in the lower extremities, primarily on the left side. He complains of significant loss of function and frequent falls due to an inability to fully pick-up his left foot and hold his hip in flexion during swing phase of gait. He describes his walking as a "stuttered walk" and frequently complains that his left foot drags and drops during steps. The …

Nfpa Fluid Power Vehicle Challenge, Rachel Wasik, Kimberly Griggy

Williams Honors College, Honors Research Projects

The objective of this project is to design a system which prioritizes safety and efficiency that uses human power converted to hydraulic power to drive a bicycle. This project is being done to compete with other university teams in making the best vehicle that runs on fluid power. It will help the members of the team to gain design and testing experience, learn about fluid power systems, and gain experience with working as a team and sharing/distributing responsibilities.

Corrosion Inhibitors: Mitigating The Degradation Of Rebar, Jake R. Hughes

Williams Honors College, Honors Research Projects

Our conjecture was twofold: first, that two compounds historically used as food preservatives could act as environmentally friendly inhibitors against rebar corrosion, and second, that molecular properties have a quantifiable influence on inhibition efficiency (%IE). To evaluate the two compounds, cyclic potentiodynamic polarization was used to determine corrosion current density (i_corr) and %IE. The “green” inhibitor candidates included sodium metabisulfite and ascorbic acid, which yielded maximum %IE values of -123900% and 91%, respectively. Results indicated that sodium metabisulfite is not a suitable inhibitor, while ascorbic acid showed potential to extend reinforced concrete’s design life without posing health or …

Aggregation-Induced Emission Probe For Alzheimer's Detection And Treatment Screening, Gemini Ramlo

Williams Honors College, Honors Research Projects

The proposed project is to research if ROF-2, an aggregation-induced emitter, can be used to screen medications for Alzheimer's Disease and to accurately detect this disease, along with its progression. This will be done through multiple incubation periods using different identifiers that have already been solidified within Alzheimer's research to prove its ability and accuracy within screening and detection regarding this disease.

Development Of A 2-Dof Robotic Uterus Manipulator, Jeremiah Eggleston, Nicole Pishnery, Siddharth Navaneetha Raj

Williams Honors College, Honors Research Projects

The objective for our senior design project was to design a better uterus manipulator to assist with hysterectomies. We worked with our advisor Dr. Sam Song from the university’s Mechanical Engineering department. There are a variety of uterus manipulators on the market currently, each with unique design features to make the manipulator safer and more effective (van den Haak et al, 2015). Our group’s design modifies and sets itself apart from manipulators currently on the market. Going off others’ attempts to make a better manipulator (Fournelis, 2022), the key modifications our design incorporates are an additional degree of freedom (for …

Ion Current Analysis And Misfire Prediction During Cold Start In A Compression Ignition Engine, Manan Jyotin Trivedi

Wayne State University Dissertations

In future, compression ignition engines are anticipated to continue powering heavy-duty trucks and certain machinery, while passenger vehicles and light-duty vehicles will increasingly be battery powered. However, compression ignition engines face challenges such as combustion instability, misfiring, and high unburnt hydrocarbon emissions when started under severe cold conditions. These issues can be mitigated through the use of real-time feedback to the engine's control module.

The ion current signal, reflective of combustion and emissions characteristics, has proven to be a reliable feedback signal under warmed-up conditions. In this dissertation, the potential of the ion current signal as a feedback mechanism during …