Digital Commons Network^™

Educational Challenge, Frederick I. Ordway Iii

Space Journal

No abstract provided.

Space Journal, Vol. 1, No. 4, Fall 1958, Rocket City Astronomical Association, Space Enterprises, Inc.

Space Journal

No abstract provided.

A Design Of Los Esteros Flood Control Dam, Constantine G. Hadjidakis

Civil Engineering ETDs

This thesis covers a preliminary design of the Los Esteros Dam based on limited subsurface investigations and laboratory testing. This earth-filled dam will be 222 feet high and will have a top width of 20 feet.

A Transient Thermal Analog Of Nuclear Reactors, James R. Hume

Nuclear Engineering ETDs

The nuclear reactor is presently receiving considerable attention as a possible source of energy for stationary power plants and propulsion systems. This has stimulated interest in many engineering problems which become very significant in reactor design work. The response of the reactor core heat transfer system to changes in power generation is one of these problems.

Vox Populi, Rocket City Astronomical Association, Space Enterprises, Inc.

Space Journal

No abstract provided.

The Design, Construction And Testing Of An Electrical, Transient Heat Flow Analyser, Bruce Wilcox

Electrical and Computer Engineering ETDs

The purpose of this investigation was (a) to design and build an analog which would produce the solution to a simplified yet typical transient aerodynamic heating problem, (b) to obtain the solution using the analog and to check the accuracy of the solution by mathematical computation, and (c) to code a more involved aerodynamic analog.

The Design Of A Solar Powered Air Conditioning System For An Albuquerque Office Building, Kuo S. Lee

Mechanical Engineering ETDs

The purpose of this investigation is to predict the performance of a solar powered jet refrigeration system for summer air conditioning, to measure the performance of the solar heat collector at the Bridgers and Paxton building in Albuquerque, and to design a Freon-12 ejector and generator for collection to that collector.

The Design, Construction And Investigation Of A Water Gravity Wave Analog Of Two-Dimensional Compression Waves In Gases, John H. Tenbrink

Mechanical Engineering ETDs

The purpose of this investigation was to design equipment for investigating and demonstrating supersonic air flow using water; to fabricate, assemble and calibrate this equipment; and to obtain and evaluate data on the validity of the supersonic flow analogy and the range of the equipment for classroom use.

Comparison Of Observed And Calculated Near-Vertical Radar Ground Return Intensities And Fading Spectra, James Arlin Cooper

Electrical and Computer Engineering ETDs

The study of ground-to-air terrain return is necessary in order to understand the functioning of radar altimeters.

Radar return at vertical incidence can be considered to be composed of two components. One, whic his returned by a mirror-like action, is called the specular component. The other, termed scatter, is due to diffuse rerediation from individual scatterers on the ground.

In recent work on return from angles near vertical, more attention has been given to the scatter component than many had previously assumed necessary.

Procedure for Gathering Data:

Two pulse radar units were used, one having a frequency of 3.8 KMC, …

Design Of An Experiment To Separate Specular And Scattered Radar Returns, Robert B. Glascock

Electrical and Computer Engineering ETDs

This paper describes the design of a radar experiment that will be conducted by the U.S. Naval Research Laboratory at Washington, D.C. The proposed experiment and the background of the problem are discussed, as well as the theoretical background, experimental background, and other design considerations are discussed in later sections.

Analysis Of Cushioned Impact By Wave Propagation Techniques, Lowell P. Martin

Mechanical Engineering ETDs

A typical problem of wave propagation which has received substantial attention concerns the longitudinal vibrations of a long, slender, uniform elastic rod after it has been dropped on one end.

The purpose of this investigation was to extend the problem to include the effect of cushioning material attached to the impacting end of a rod similar to that described above; and to conduct experiments designed to verify the analysis. This study is essentially the first step toward the analysis, by wave propagation methods, of many practical impact problems encountered in military airborne operations, experimental rocket programs, and the packaging industry.

A Study Of The Reset Cycle Of A Half-Wave Self-Saturable Magnetic Amplifier, William W. Lee

Electrical and Computer Engineering ETDs

It was the purpose of this study (1) to investigate the reset cycle of a half-wave self-saturable magnetic amplifier by graphical analysis of the irregular voltage functions appearing across the gate winding during reset; and (2) to determine if possible from this analysis a more satisfactory design method than those now available. Conditions of constant current reset were employed and the core material used had a nearly rectangular hysteresis loop. Resistive loads only are considered.

Utilization Of The Relationship Between The Complex Immittance And The Indicial Immittance Functions For The Synthesis Of Two Terminal Networks, Julian T. Lefler

Electrical and Computer Engineering ETDs

It was the purpose of this study (1) to develop a new method of network synthesis from a specified complex immittance function; and (2) to demonstrate the application of the method by means of its use in the solution of representative synthesis problems. This work deals only with the synthesis of two terminal networks containing linear, passive, lumped-constant elements, from given rational immittance functions of the complex frequency variable.

Not considered part of this work are (1) the development of the immittance function from frequency-response specifications (the approximation problem); or (2) the treatment of active, non-linear, or time varying network …

A Study Of A Complementary Symmetrical Power Switching Circuit, Glenn S. Mills

Electrical and Computer Engineering ETDs

This paper contains an analysis of a symmetrical, complementary, power switching circuit employing complementary power transistors. A DC analysis is made for the bistable states. Also described is a voltage regulation and bias circuit which improves stability and contributes to the protection of the transistors. The problem of switching transients is investigated and empirical results presented to support theoretical considerations. A new triggered method is proposed to utilize the bilateral characteristics of a transistor. Applications of the circuit are suggested for controlled-frequency and self-triggering modes of operation. A method and analysis for self-triggering is presented. The advantages of this power …

The Use Of Electrical Resistance Strain Elements In Three-Dimensional Stress Analysis, Robert I. Brasier

Electrical and Computer Engineering ETDs

The purpose of this thesis is to present a new method of experimental stress analysis and to give the solution to a problem which has been handled by this method.

A Study Of A Production Control System In A Job Order Die Casting Plant, Robert Gordon Woodnorth

Theses

This thesis examines the production planning and control system in a job-order die casting plant. After comparing to the criteria for an ideal system the following changes were recommended.

1. Central work storage and dispatching. This would reduce work in process and workload fluctuations through closer planning. It would also provide a perpetual inventory system and a central control point which would be constantly informed of production progress.

2. Operator trucking. By having operators do their own trucking material handling costs and production delays would be reduced.

3. Simplified job cost accounting. The use of standard costs for finishing and …

Determination Of Q Factors And Operating Characteristics For Microwave Cavities And Oscillations, W.P. Stearns

Electrical and Computer Engineering ETDs

This paper has as its objective the presentation of the theory involved and method used with respect to the resonant cavity parameters; loaded Q, unloaded Q, external Q, pulling figure, and circuit efficiency for the resonant cavity investigated. Experimental data on a particular cavity are discussed and the previously mentioned cavity parameters determined with the use of such data and the particular method presented. A Rieke diagram for the particular cavity investigated is also presented and discussed.

Construction Of A Heavy Duty Military Airfield On Permafrost., Owen N. O'Leary

Civil Engineering ETDs

An examination of the map of the northern hemisphere will show that the two great population areas of opposing ideologies are located across the arctic regions from each other. This fact has been recognized by the U.S. military authorities since the early 1940’s, and an effort has been made to locate military forces in these regions to act as a possible deterrent to any aggressive action. The nature and geography of this region generally preclude any military forces except combat airfield. The most outstanding and possible only example of a major military airfield located entirely on permafrost material in these …

Beyond This Star, James L. Daniels Jr.

Space Journal

No abstract provided.

Electronic Computation In Bridge Design, L. R. Schureman

Kentucky's Annual Forum on Transportation

No abstract provided.

Spilitic Rocks And Mineral Deposits

School of Mines and Metallurgy Bulletins

The principal results of research work on spilitic rocks and mineral deposits carried on since 1945 are briefly summarized. Emphasis is placed on the influence of the results on the theories of rock and ore genesis, particularly the change of "philosophy of exploration" based on the existence of hydromagmatic ore deposition. A re-classification of magmatic mineral deposits is offered.

Performance Parameters Of Low-Density Ammonium Nitrate Base Explosives; Experimental Results And J. Taylor's Method, Mohammad Azhari Warga-Dalem

Masters Theses

"Ammonium nitrate has been known to the explosive industry for a long time. Compelled by the ever increasing mining costs, in 1954 "Akremite" was introduced to the market. It is a simple carbonaceous ammonium nitrate mixture and is the cheapest explosive available to the open-pit operators.

During the following years considerable amount of research was done, resulting among others with the introduction of ammonium nitrate-hydrocarbon mixtures as an explosive. During the Second World War research was done toward the refinement of the hydrodynamic theory. Several methods of calculating the detonation velocities of the explosives were introduced: Brown (1942), Kistiakowski and …

Design Of Liquid-Liquid Extraction System, Mehdi Rahmani Fard

Masters Theses

"The unit operation of liquid-liquid extraction has developed enormously in the last 20 years and is now recognized as one of the most important techniques for the physical separation and refining of industrial liquids. For years the conventional apparatus used for liquid-liquid extraction has been towers employing countercurrent flow of the liquids and equipped with various means to increase the interfacial area.

The countercurrent column consists of a tower through which flows a continuous phase while countercurrent to this flow is a stream of droplets (the dispersed phase). Provision is made for dispersing one phase with a settling region at …

Performance Characteristics Of A Tubular Regenerative Heat Exchanger, Harry J. Sauer Jr.

Masters Theses

"The term regenerator is widely used to define any type of heat exchanger in which the heat is alternately stored and removed...The present investigation is concerned with the calculation of the characteristics of the "single-blow", tubular regenerative heater, its dimensions and performance. In the analysis in this thesis, the heat is considered to be stored in bundles of tubes initially preheated by hot gases flowing through the heater and subsequently cooled by the flow of air. This paper makes no attempt to deal with the effects of radiation from the outer row of tubes to the heater shell"--Introduction, page 1-3.

Frost Formation And Its Influence Upon Heat Transfer, Jack Lewis Loper

Masters Theses

"The cooling of a gas-vapor mixture or a mixture of several vapors, in the general case, results in condensation (phase-change) of one or more of the vapors when their respective dew-points are reached. This results in a mass transfer of the vapor to the cooling surface accompanied by energy transfer as the vapor gives up its latent heat of vaporization to the surface and becomes a liquid. The liquid accumulation adds a resistance to the further transfer of mass and energy unless some means is provided for its removal from the surface, such as gravity action.

In this paper we …

Reconstruction Of A Model L Podbielniak Fractional Distillation Apparatus, Raymond Bauer

Masters Theses

"The purpose of this thesis was to reconstruct a Model L Podbielniak Fractional Distillation Apparatus to provide equipment suitable for the study of batch multicomponent distillation. The apparatus will also serve as an analytical instrument. The equipment was instrumented to automatically control the distillation, but an operator is needed to select fractions and insure the proper functioning of the controls.

Samples of hydrocarbon mixtures of known composition were analyzed to prove the successful operation of the reconstructed apparatus"--Introduction, pages 2-3.

A Statistical Approach To The Zonation Of A Petroleum Reservoir, Leroy Allan Beghtol

Masters Theses

"The problem of dividing a reservoir into distinct permeability zones, in order to predict fluid flow and thereby the production history of the field, has long troubled the petroleum engineer. As a solution to this problem a new statistical method for zoning a reservoir was developed, using a modification of the analysis of variance technique. The application of the statistical zonation procedure to permeability data obtained from eight closely spaced wells substantiated the validity and effectiveness of the new method in determining distinct permeability zones"--Abstract, page iii.

The Development Of A Device To Replace The Oil Well Dynamometer, Jerry Bernard Overton

Masters Theses

"The mechanical dynamometer is recognized as being a valuable tool in measuring resultant forces acting on the polished rod of an oil well pump. The dynamometer is used extensively to determine loads, torque, and horsepower. "It is also used to determine pump action and trouble-shoot for any seemingly abnormal pumping condition."

Although it is desirous to periodically make dynamometer studies, it is also very time consuming. Because of high labor costs, it has been almost discontinued by many companies. The author became convinced that a less costly method of obtaining the same information could be developed. This method was the …

Operational Characteristics Of A Small Sewage Oxidation Lagoon, Karlheinz C. Muhlbauer

Masters Theses

"With the rapidly increasing population in the United States the adequate disposal of sewage has become one of the major technical problems which the sanitary engineer has to solve. In most areas it is no longer acceptable practice to discharge domestic sewage or industrial waste products directly into streams or lakes because of the resulting pollution of the water, which may later be used for drinking or recreational purposes. Many larger cities have, therefore, adopted some method of sewage treatment which renders such wastes safe and unobjectionable before they are discharged into a lake or stream. Most of these methods …

Methods To Improve The Metallurgy Of Bolivian Tin Ores, Oscar Davila-Michel

Masters Theses

"Tin is a rare element; among the base metals it is one of the rarest. Although it was one of the first metals used by man and has been used since prehistoric time, the ore-dressing and metallurgical methods of tin are inefficient and very wasteful.

The only tin deposits of importance in the Americas are located in Bolivia, South America, and it is in Bolivia that the problems of tin metallurgy are greatest. More than 50% of the tin that is mined in Bolivia is lost in the tailing dumps of the beneficiation plants. In a country where the export …