Digital Commons Network^™

An Investigation Of The Effects Of Pozzolans On New Mexico Concrete Aggregates, Harry W. Montgomery

Civil Engineering ETDs

It was the purpose of this investigation to determine some of the effects a pozzolan has on Portland cement concrete when New Mexico aggregates are used. The specific items investigated were (1) to determine the effects of a pozzolan on the alkali aggregate expansion in concrete; (2) to show the effect on the compressive strength of concrete and the tensile strength of mortar briquettes when part of the Portland cement is replaced with a pozzolan; (3) to determine whether or not the “Mason Jar Expansion Test” would give reliable results; and (4) to determine whether or not an aggregate, with …

Comminution Studies, George A. Grandy

Bachelors Theses and Reports, 1928 - 1970

Comminution, reduction in size, is one of the most important, yet least understood, steps in mineral dressing. So that more efficient comminuting devices may be designed and constructed, a better knowledge of the relationship between energy consumption and size reduction is desired. Occasional studies during the last 100 years have produced a few "laws" purporting to describe this relationship. In each case, the promulgators and supporters of these laws have presented experimental evidence for their verification. Obviously, all of these advocated practices cannot be correct. To the mill designer, the problem is "Which, if any, of these laws are valid." …

A Microwave Technique For Determining The Electronic Properties Of A Moving Plasma, Bernard Hayes

Electrical and Computer Engineering ETDs

A microwave interferometer technique which may be used as a diagnostic tool for determining the electronic properties of a moving plasma is described and analyzed. The plasma and microwaves are confined in a wave guide and longitudinal observation is employed. The complex reflection coefficient determined from resultant standing-wave pattern provides the means for obtaining the complex dielectric constant, conductivity, electron concentration and collision frequency of electrons with molecules in the plasma. The plasma used for these experiments is the reaction products of a gas detonation.

Functional And Economic Considerations Of An Electrical Line Feeding Large Concentration Loads, Seth O. Lewis

Electrical and Computer Engineering ETDs

This paper discusses the considerations required for selecting particular characteristics of [transmission lines] and presents an original method of obtaining the most economical solution. A typical problem at the Public Service Company of New Mexico is solved to illustrate the usefulness of this method.

Design And Use Of A High Power Laser For Plasma Generation Studies., Philip N. Mace

Electrical and Computer Engineering ETDs

The advent of high power lasers to the technological scene has introduced the possibility of creating new effects utilizing the interaction of this high intensity light with matter. C. M. Fowler and D. B. Thomson of the Los Alamos Scientific Laboratory suggested in 1963 the possibility of using a high power laser to pre-ionize and heat a target material to be contained in an explosively driven theta pinch machine. There had been calculations performed by John Dawson, Princeton University, and A. Engel­hardt, Westinghouse Research Laboratories, which indicated that such an approach was theoretically feasible. The laser powers required, however, were …

Determination Of Required Component Reliability From System Reliability Requirements, Arthur M. Breipohl

Electrical and Computer Engineering ETDs

No abstract provided.

"Highways And People", Ellis L. Armstrong

Kentucky's Annual Forum on Transportation

No abstract provided.

Specification For The Design Of Light Gage Cold-Formed Steel Structural Members, American Iron And Steel Institute

American Iron and Steel Institute (AISI) Specifications, Standards, Manuals and Research Reports (1946 - present)

No abstract provided.

Analysis And Synthesis Of A Current Regulator System, William P. Aiello

Electrical and Computer Engineering ETDs

This report describes a practical current regulator system used to accurately control the current delivered by a 500 kilowatt motor-generator unit. The generator supplies its current of 2000 amperes at 250 volts to a large water-cooled air-core solenoid used by LASL Group P-7 for experiments in connection with the Sherwood program.

After a general discussion of the system specifications and the basic regulator loop, each of the components in the basic regulator loop is described in considerable detail. The description, in most cases, is mathematical in nature although many circuit diagrams are included with brief descriptions when necessary for proper …

Comprehensive Survey Of Sedimentation In Lake Mead, 1948-49, W. O. Smith, C. P. Vetter, G. B. Cummings, U.S. Bureau Of Reclamation

Publications (WR)

Reservoirs are becoming an increasingly prominent feature of the American landscape. Built for flood mitigation and to change a fluctuating river into a dependable source of water for irrigation, power, and other purposes, they are predestined, like natural lakes, to be destroyed sometime following their creation. Sedimentation sooner or later robs most lakes and reservoirs of their capacity to store water. The significance of sedimentation in the life of Lake Mead, the largest artificial reservoir in the world, was realized when the plan for the reservoir was conceived, and an aerial survey of the floor was made in 1935 before …

A Method Of Design For Spiral Reinforced, Eccentrically Loaded, Concrete Columns, Lloyd O. Senter

Masters Theses

"This thesis presents a method of designing spiral reinforced, eccentrically loaded, concrete columns on the basis of the 1957 American Association of State Highway Officials specifications.

Equations from AASHO, in conjunction with equations derived in this thesis, are programmed for and solved by the IBM 650 digital computer. The data obtained from the computer is plotted such that, given the normal load and moment on a column, the minimum required area or reinforcing steel may be read directly from the graph.

The derivation or equations, the computer program, and the graphs are included in the thesis"--Introduction, page 1.

Temperature Distribution In A Semi-Infinite Solid As A Function Of The Input Heat Flux, Lloyd Carl Laciny

Masters Theses

"In this thesis the problem of varying heat flux into a semi-infinite solid initially at zero temperature is investigated. Varying heat flux means that the heat transferred to the solid by its surroundings is a function of time; in this particular problem it is chosen to be an exponential function of time. A semi-infinite solid is one which is bounded by only one plane.

This subject has achieved considerable importance in the field of space technology. A body in space is beyond the realm of aerodynamic heating and non-uniform skin temperatures reached as a result of radiation from a high …

Physical Property Tests Of Rock, Centrifugal Tests And The Design Of Underground Mine Openings, Samuel Shu Mou Chan

Masters Theses

"Proper design of stable underground mine openings is important to the mining industry today. Various methods have been utilized by investigators to approach this goal.

A review of previous investigations of each of the phases of underground mine opening stress analysis is presented.

An approximate method of designing underground mine structures based on estimation of the initial stress field, rock physical property tests, and model tests, together with preliminary field data, is presented, and a specific example given"--Forward, page i.

Effect Of Boundry Layer Control, Through Surface Holes, On The Film Coefficient Of Convective Heat Transfer, Jainti Prasad

Masters Theses

"This thesis has as its objective, the effect of some boundary layer control on the convective heat transfer film coefficient, metal to liquid. The boundary layer control was produced by drilling 1/16 inch diameter holes on the tube surface.

In this modern world of atoms and the current development of large quantities of its energy at low cost, the subject of designing heat exchange devices of higher efficiency is receiving considerable attention. In a reactor, or any type of heat exchange device, there are limits for the temperatures of a heat exchange surface because of corrosion, strength of metals etc. …

A Thermodynamic Study Of The System Pbo-Pbs, John P. Hager

Masters Theses

"An experimental investigation was conducted in order to determine the thermodynamic and kinetic behavior of the system PbO-PbS.

The thermodynamic behavior of the system PbO-PbS was studied by measuring the P_SO₂ in argon-SO₂ mixtures equilibrated with various PbO-PbS mixtures in a recirculating-type equilibrium apparatus, and analyzing the condensed phases by means of X-ray diffraction.

The effect of temperature and PbO/PbS ratio on the rate of SO₂ evolution was investigated in order to determine the reaction mechanisms involved in the approach to equilibrium.

A sodium hydroxide, hydrogen peroxide titration technique was employed in the analysis of SO_{2 …}

Automatic Tuning Of A.C. Compensating Networks, Giles C. Sinkewiz

Masters Theses

"The purpose of this thesis is to illustrate the practicality of using an auxiliary servo system to shift parameters in damping networks of the main servo system.

Since amplification is most easily achieved with A.C. amplifiers and since A.C. servo motors are superior in operation to D.C. servo motors, because no brushes or commutators are needed, the A.C. servo system is widely used. However, one major problem is confronted when designing an A.C. servo system. This is the problem of designing damping circuits and compensating circuits which are insensitive to carrier frequency fluctuations. Notch filters provide the desired transfer functions, …

Preparation Of Casting Slips Containing Ferrous Powders And Alginates, Robert Eugene Newcomer

Masters Theses

"The preparation of casting slips containing ferrous powders dispersed by alginates was studied and an attempt was made to determine the mechanism by which suspension was attained. The colloidal aspects of preparing ceramic casting slips are discussed and an analogy is drawn to preparation of metallic slips suspended by alginates.

Sodium and ammonium alginates were used to suspend stainless steel and iron powders. The effect of NaOH, HC1, and various phosphate additions on the properties of slips and algin solutions was considered.

It was found that colloidal concepts can not be applied to explain observed behavior in the system studied. …

A Study Of The Feasibility Of Stabilizing Putman Soil With Hydrated Lime And Portland Cement In Combination, John Henry Kern

Masters Theses

"This paper is the report of a feasibility study of the combined use of hydrated lime and portland cement to stabilize the troublesome Putnam soil of northern Missouri. In its natural state, this soil is highly plastic, possesses great shrinkage and swell characteristics when the moisture content is changed and is classified as an A-7-5 soil by the A. A. S. H. O. Standards for the Classification of Highway Subgrade Materials.

During the course of this investigation, the following tests were performed: (1) Moisture-Density Relationships for soil with admixtures; (2) Triaxial Compression Test; (3) Unconfined Compression Tests; (4) Freeze-Thaw Tests; …

The Equalization And Optimization Of A Third-Order Type-1 Position Control System, Viswanatha Seshadri

Masters Theses

"While the practice of feedback control dates back to the day when the earliest living organisms began to react to their environmental conditions and the changes therein, it has been only during the past two decades that this technique came to be subjected to a scientific examination. Yet, an astoundingly rapid advancement has resulted in the field of servo-mechanisms, contributing substantially to the development of modern civilized existence and activity to its present standards, and promising to contribute, to an ever-increasing extent, to the accelerated progress of scientific and industrial enterprise in this space age.

The principal concerns of the …

A Study Of The Reaction Of Hydrated Lime With Pure Clay (Kaolin) In Clay Stabilization, Chiyyarath Velayudhan Girijavallabhan

Masters Theses

"The work presented is the investigation of the reaction of pure Kaolinite clay with hydrated lime in clay stabilization. Pure Kaolin clay, ranging from one micron to five microns in size, was mixed with calcium hydroxide in the form of a paste. These mixtures were permitted to react for varying periods of time. An attempt was made to separate the lime from clay lime mixture by density separation using a mixed solution of carbon tetrachloride and tetrabromoethane. Since the above method failed because of the formation of a yellow gelatinous suspension, the lime was removed by washing the clay lime …

A Method For The Prediction Of Detection Ranges For Pulsed Doppler Radar, Phillip Orlan Brown

Masters Theses

"Modern radar systems must provide greater detection ranges both against high and low altitude targets because of the significant advances in weapon speed and range. Extended range indicates that the power transmitted by the radar must be increased. It follows, that ground return becomes a problem even at high altitudes.

There are at present three basic types of radars which are (1) pulsed, (2) continuous wave, and (3) pulsed doppler radar. The conventional pulsed radar now closely approaches the theoretical optimum performance; however, it does not have the inherent ability to distinguish between ground return and moving targets. The continuous …

Factors That Influenced Homesteading And Land Abandonment In San Juan County, Utah, Melvin J. Frost

Theses and Dissertations

Homesteading in San Juan County, Utah is for the most part, located on Sage Plain at elevations between 6,000 to 7,200 feet. Sage Plain is an undulating surface deeply dissected with canyons. The soil is relatively shallow and the predominant vegetation is pinyon, juniper, sage brush and blue-stem grass.

The 52 year mean precipitation is 15.47 inches. Since the beginning of weather records there has been a noticeable decrease in the annual precipitation. There is generally sufficient moisture to mature winter wheat. Pinto beans are also grown in the more favorable locations.

Principle factors that have influenced homesteading and land …

Methods For Calculating The Minimum Amortization Tonnage And Maximum Present Value For An Ore Body, Garrett M. Sainsbury

Masters Theses

"The discussion is divided into three parts. Part I describes a procedure for determining the mining rate that gives the minimum amortization tonnage required of an ore body, and the amount of that tonnage. The basic idea is that amortization tonnage is equivalent to the estimated capital costs, including interest, divided by the estimated operating profit per ton. Both capital costs and operating profit per ton can be expressed as functions of mining rate by making use of empirical equations. Therefore, amortization tonnage can be expressed as a function of mining rate. The amortization tonnage is calculated for a series …

Heat Transfer In A Vortex Flow Metal To Air, Elisha Rachovitsky

Masters Theses

"In this study heat transfer in a vortex flow has been investigated experimentally and analyzed qualitatively.

Air was forced through a Ranque tube in order to get a swirling turbulent flow in its "hot" section. The test section, having a diameter of .355 inches and a length of 27.5 inches, was heated by an induction coil.

Three types of flow were under investigation: a linear turbulent flow, a vortex uniflow and a mixed vortex-linear turbulent flow.

The experiments covered a range of tube-wall temperature from 570 to 900 Deg. R and inlet pressure to the vortex generator ranged from 25 …

Determination Of Vapor-Liquid Equilibrium Data By Continuous Distillation, David William Bunch

Masters Theses

"The procuring of experimental vapor-liquid equilibrium data has been a problem of considerable importance to chemical engineers for a number of years. Modern distillation theory and practice have made accurate vapor-liquid equilibrium data practically a necessity.

Using conventional methods for determining vapor-liquid equilibrium data, an experimenter can obtain only a single vapor-liquid equilibrium composition per trial. Ramalho working with Tiller has developed a new method which makes possible the determination of all values of the vapor and liquid concentrations in a single experiment.

The work done by Ramalho indicated that the necessity for very precise temperature measurements presented a serious …

The Redesign And Construction Of A Rotating Disc Contactor, Richard Henry Okenfuss

Masters Theses

"Liquid-liquid extraction has played a major role in the processing of nuclear fuels. The Department of Chemical Engineering of the Missouri School of Mines and Metallurgy realizing this, petitioned the Atomic Energy Commission for funds to design and construct an instructional facility representing the chemical processing of nuclear fuels. With this unit and its solvent recovery equipment, in which stress is placed on extraction and distillation, not only are the principles of nuclear fuels processing demonstrated, but the more basic concepts of mass and energy transfer are also illustrated. Extraction depends upon solubility differences to achieve a transfer of a …

Segregation Method As Possible Process To Beneficiate Oxidized Lead Ores, Jose Molfino Tomasio

Masters Theses

"In this investigation it has been demonstrated that the Segregation Process has merit for treating oxidized lead ores.

The process comprises heating the crushed ore with salt and coal at about 750° C. to produce metallic lead attached to the carbon particles, which then is recovered by conventional flotation methods.

The quantities of sodium chloride and coal required for the best segregation of lead obtained in this work was 1.0 percent of coal and 1.0 percent of salt by weight.

Good segregation was obtained by using salt and coal as fine as 65 or 48 mesh. Segregation varied with the …

The Separation Of Selected Radioactive Fission Products By Electrodialysis, Jerry David Vie

Masters Theses

"The recent advent of nuclear energy has opened an era of almost unlimited power and countless problems. A problem of extreme importance is the recovery of unburned nuclear fuel and the claiming of transmutation products, such as Pu²³⁹ and U²³³, from the irradiated fuel elements. The chemical processing must also separate the fission products from the fissionable material if the fuel is to be used again.

At present, the irradiated fuel elements are stored for 90 to 120 days to allow the intense short half-life activity to decay. After "cooling down", the nuclear fuels are separated from …

A Method Of Fuel Testing In A Cfr Engine, George R. Baumgartner

Masters Theses

"At the present time, only a very small fraction of motor fuels produced for domestic use in the United States contain any alcohol in their blends. Soma foreign markets, notably the Philippine Islands and South American Countries use high proportions of alcohol in their motor fuel blends. Special purpose fuels in the United States which have alcohol blended with other compounds, have been used for engines from which maximum horsepower output is imperative. An example of this type of motor fuel blend might be found in the competitive motor sports involving motorcycles, stock automotive equipment, and special racing equipment.

An …

Construction Of A Pulsed Perforated-Plate Extraction Unit, Clarence James Vetter Jr.

Masters Theses

"Liquid-liquid extraction is an important operation in the production and reprocessing of nuclear fuels. In the purification of uranium by liquid-liquid extraction, uranyl nitrate is separated from impurities by extraction into an organic solvent, followed by re-extraction into an aqueous phase. Further processing of the aqueous uranyl nitrate solution is tailored to yield uranium metal or any desired uranium compound.

In order that students in nuclear and chemical engineering may have an understanding of the practical as well as theoretical aspects of liquid-liquid extraction, a model of a uranium purification plant was designed and built in the Unit Operations Laboratory …