Digital Commons Network^™

Velocity And Kinetic Energy Distribution Of A Submerged Jet., Patrick Shepard Couch

Masters Theses

"The velocity distribution in a cylindrically bounded region of water induced by a submerged axisynnnetric jet of water, has been investigated. Velocity profiles at successive levels were constructed. The continuity equation was shown to be only approximately verified by the velocity profiles.

The kinetic energy for each level was computed and given mathematical expression"-- Abstract, p. 2

Stiffness Of Lightweight Reinforced Concrete Beams, Rameshchandra H. Patel

Masters Theses

"This work is a presentation of the findings of an experimental measurement of stiffness (El) for reinforced and nonreinforced lightweight and normal concrete. The experimental values of stiffness are compared with values obtained using standard reinforced concrete theory. In all, thirty beams, fifteen for lightweight and fifteen for normal concrete, each having the compressive strength of approximately 4, 500 psi, were tested. In addition to stiffness measurements, a relationship was obtained between the dynamic modulus of elasticity and the ultimate compressive strength at various ages for the particular lightweight concrete used"--Abstract, page ii.

Mass Transfer To Droplets: Effect Of Non-Newtonian Continuous Phase., Hsin Chih Wu

Masters Theses

"Since non-Newtonian fluids are frequently encountered in the chemical and process industries, it is important that the transport processes which are commonly encountered be thoroughly investigated. Although studies of fluid mechanics and heat transfer with these fluids have been reported, virtually no work has been reported in the study of mass transfer. This is particularly true of mass transfer in turbulent flow.

The purpose of this investigation is to study the liquid-liquid mass transfer phenomenon in turbulent flow associated with single droplets in non-Newtonian continuous phases. The results are compared with those obtained in Newtonian systems. The data obtained will …

Influence Of The Heat Release On Thermodynamic Characteristics Of Diesel Engines., Shirish Amritlal Desai

Masters Theses

"A Diesel. engine is an internal. combustion engine in which the fuel. is ignited by the heat of compression. Thus, the Diesel. engines are known as compression-ignition (C.I.) engines. The engine received its name: from its inventor, Dr. Rudolf Diesel., who in 1893 published a book under the title, '' Theory and Construction 0£ Rational. Diesel Engine". The first successf'u1 Diesel. engines, using liquid: fuel., which was injected into the cylinder by a blast of high-pressure air, were manufactured by the M.A.N. Company of Germany in 1895"-- Introduction, p. 1

Artifact Filter., Kent William Swearingen

Masters Theses

"Peripheral blood pulse monitors are highly susceptible to noise-artifact-- in their present stage of development. The purpose of this thesis is to demonstrate a feasible means for filtering the artifact, using existing monitors. Since no peripheral pulse monitor (transducer) was available for experimentation, a simulated test input was devised with frequency variations from JO cycles/minute to 1.50 cycles/minute.

The filtering circuit predicts the time location of each input pulse. The location of the prediction is governed by the accuracy of the preceding prediction. This is controlled by an R-C timing circuit with a Schmitt Trigger and relay.

From the data …

Development Of A Fluor-Mica Dielectric Using Glass-Ceramic Fabrication Methods., James Joseph Tuzzeo

Masters Theses

"A tetrasilicic fluor-mica, K₂Mg₅si₈o₂₀F₄, was synthesized using glass-ceramic fabrication methods. Bubbles, rods, and disks of glass-mica were formed, and heat treated at selected temperatures between 620°c and 1160°c for various time periods. Density changes were correlated to mica content to determine the relative amounts of crystalline mica phase precipitated after heat treatment. Dielectric losses and dielectric constants of the glass-mica disks were measured for correlation to mica content"--Abstract, p/ ii

Real Time Testing With A Time Scaled Analog Computer., Wayne F. Balsman

Masters Theses

"A present limitation to the testing of a physical subsystem within an analog simulation is that the analog computer must compute in real time. If it is necessary to time scale the simulation of the complete system, a physical subsystem of the complete subsystem may not be tested within the simulation. Therefore, a means of changing the time scale of the analog signal is needed to test a physical subsystem within a time scaled analog computer simulation.

In this thesis a means of time conversion by sampling the analog signal at one rate, storing the samples, and reading the samples …

The Effect Of Gap Graded Aggregate On The Properties Of Hot Mix Asphaltic Concrete, Maurice L. Northcutt

Masters Theses

"The objective of this investigation was to determine the effects of deviations from the recommended gradation of aggregate upon asphalt concrete mixes. The aggregate used in this study was a good grade Missouri Limestone and was mixed with an asphalt cement of 85-100 penetration grade. A control mix was designed in accordance with the Marshall Method using a gradation recommended by the Asphalt Institute. Ten aggregate blends were prepared by wasting certain fractions or combinations of fractions and the wasted weights were redistributed into the coarser or finer aggregate sizes. The test mixes were designed using the same method and …

The Importance Of Radiation As A Means Of Controlling Surface And Internal Temperatures Of A Semi-Infinite Solid, Kenneth C. Woodruff Jr.

Masters Theses

"This problem is concerned with the temperature history of a semi-infinite solid bounded by one flat surface.

Heat was applied by convection from a hot fluid to the flat surface of the solid which was originally at a uniform temperature. Heat was radiated from the flat surface to black space and conducted into the solid according to Fourier's law. The temperature at the surface, and at several points beneath the surface, was determined as a function of time.

A method for solution of such a problem is demonstrated here by the use of numerical analysis and the Royal McBee LGP …

Investigation Of The Effect Of The Wall Thickness On The Residual Stresses Developed In Thick Wall Cylinders Due To Water Quenching From The Outside Surface., Ghanshyam Chandubhai Patel

Masters Theses

"This investigation has been made to determine the residual stresses in thick wall cylinders by the use of strain gages.

The cylinders were quenched from their outer surface i n water from a temperature of 1000°F, and the resulting residual stresses were determined by Sachs boring-out method. The effect of the wall thickness of the cylinders on the residual stresses and the error developed due to the boring operation were discussed"--Abstract, p. ii

Densification Studies Of Three-Component Refractory Grog Systems., Jerome Dale Patterson

Masters Theses

"The bulk density and crushing strength properties of three-component refractory grog systems that were formed by mechanical impact or by mechanical vibration were determined.

Aqueous alkali silicate solutions of various types, concentrations, and amounts were investigated as room temperature binders for these grog systems. Compositions having maximum bulk densities were determined for each of six different three-component refractory grog systems. The densification rate curves for systems formed by mechanical impact were determined"--Abstract, p. ii

A Determination Of The Theoretical Stresses In A Deep Beam., James William Tritz

Masters Theses

"This paper presents an analytical solution of the stress distribution in a deep beam of finite length. The beam being considered is analyzed as one of plane stress. The method employed superimposes two stress functions each of which is a trigonometric series. The first stress function satisfies all boundary conditions except that of zero stress on the vertical faces. The second function is found, so that, when combined with the first function, all boundary conditions are satisfied. The IBM 1620 digital computer is then used to find the stresses for a particular beam. The results of this analysis are then …

The Prediction Of The Thermal Conductivity Of Various Binary Non-Polar Gaseous Mixtures., Chester Foon-Chen Feng

Masters Theses

"A simple method for predicting the thermal conductivity of binary non-polar gaseous mixtures from the force parameters of the pure components and composition was developed. The method is an extension of the application of the combining methods previously derived for viscosity predictions. Altogether, the published thermal conductivities of 683 binary non-polar mixtures at various temperature levels were compared with the corresponding calculated thermal conductivities resulting from the prediction method. The corresponding values predicted from Hirschfelder, Curtiss and Bird's expression were also compared.

Among the 683 binary mixtures, there were 138 di-di, di-poly, and poly-poly mixtures, 241 mono-

The Electrical Analogy Of Critical Speed For The Transverse Vibrations Of A Shaft With One, Two And Three Masses, Ashok Z. Patel

Masters Theses

"The object of this thesis is to determine the critical speed of a shaft by an electrical analogy. The shaft considered is of constant diameter and is simply supported at the ends by fixing it in self aligning bearings. The weight of the shaft is assumed to be proportionally distributed in the attached masses.

The original system is first of all converted to an equivalent simple spiring mass system by calculating the influence coefficients and hence frcan these determining the spring constants. The spring mass system obtained is then converted to an equivalent electrical circuit.

A sine-square wave frequency generator …

A Study Of The Separation Of A Mixture Of Carbon Dioxide And Hydrogen By Means Of An Orifice., Larry Gene Bauer

Masters Theses

"The purpose of the investigation was an attempt to verify a statement made by Partridge in an effort to discover a new method of separating gaseous mixtures. Partridge stated that when a constant pressure is applied on two gases of different specific gravity, a larger volume of the l igl1ter gas is forced through the orifice. Orifices of 1.016, 0.319, and 0.222 millimeter in diameter were used in the course of the investigation.

It was found that with the apparatus used in the research endeavor, no separation of the mixture of hydrogen and carbon dioxide could be obtained"--Abstract, p. i

Effect Of Hydroxyethyl Cellulose On Properties Of Concrete At Early Ages., Vipinchandra R. Shah

Masters Theses

"In this investigation, hydroxyethyl cellulose was used as an admixture in plain concrete. The admixture was tested for its effect on the compressive strength of plain concrete cylinders and for its effect on the flexural strength of plain concrete beams. Specimens were also tested for freeze-thaw durability and shrinkage.

The test results indicated that hydroxyethyl cellulose has the effect of increasing the compressive strength and decreasing the flexural strength of plain concrete. The rapid freezing and thawing tests showed that the durability increases with increase in amount of admixture.

The tests were carried out in the Materials Laboratory of the …

A Study Of The Crystallographic Orientation Dependence Of Electrical Resistivity In Zinc, Paul Frederic Becher

Masters Theses

"A potentiometer and galvanometer setup was used to obtain electrical resistivity data for polycrystalline zinc. Cold working textures were investigated by the reflection technique with a quadrant x-ray spectrometer.

Resistivity data were obtained for specimens that were reduced up to forty per cent from the as received condition, and the corresponding textures were studied. The results indicated that the resistivity change in the rolling direction is due to the reorientation of the c-axis in the rolling caused by cold working"--Abstract, page ii.

Structural Analysis Of Open Channels On Elastic Foundation., Wan-Cheng Liu

Masters Theses

"This study is to analyze continuous open channels used for fluid flow and supported on soil which is considered to provide an elastic foundation. The basic assumption is that the reaction forces of the foundation are proportional at every point to the deflection of the channel at that point. The walls of the channel are considered vertical in all cases but are subjected to various lateral pressures due to different embankment loading conditions"-- Abstract, p. ii

The Effects Of Granular Size On The Thermal Conductivity Of Fine Sand, Fikri Yalvac

Masters Theses

"The Thomas method (1) for determining the thermal conductivity of solid materials can be used for the determination of the thermal conductivity of granular materials. In this thesis this method has been used to determine the effect of the granular size of sand cn its thermal conductivity.

River sand was classified according to size by the Tyler Standard Screen Scale into 50-60, 50-80, 80-100, 100-200, and below 200 mesh size. These sands were used for the experiments. The clay was separated from these samples to obtain pure river sand for the experiments.

According to the International Critical Tables, the thermal …

The Anodic Dissolution Of Zinc In Nitrate Solution., Jo Lisle Reed

Masters Theses

"The increasing demand for protective metals as coatings and non-corrosive alloys has stimulated extensive research on the fundamental behavior of metals in corrosive media.

One of the problems still unsolved is the nature of the mechanism of the anodic dissolution of metals like zinc, magnesium, beryllium, cadmium, and aluminum in aqueous salt solutions. Several schools of investigators have proposed different and opposing theories to explain the discrepancies which often arise between coulometric data and the weight loss of metal electrodes in certain salt solutions.

The purpose of this investigation was to obtain experimental data for the anodic dissolution of zinc …

Correlation Of Chemical Structure And Distensibility Of Polyesters., Nitin Jhaverbhai Bhimani

Masters Theses

"Maleic anhydride and fumaric acid are important raw materials for the manufacture of unsaturated polyesters. Unsaturated polyesters are the esterification products of unsaturated dibasic acids and polyvalent alcohols, polymerized to a high molecular weight resin"--Introduction, p. 1

The Prediction Of The Viscosity Of Multi-Component Non-Polar Gaseous Mixtures At Atmospheric Pressure., Gary D. Fehsenfeld

Masters Theses

"The applicability of the Strunk, Custead, and Stevenson method for predicting the viscosities of multicomponent, non-polar, gaseous mixtures vas investigated. The viscosities of 24 ternary and quaternary gaseous mixtures were experimentally determined, at 3 temperature levels, and compared with the corresponding calculated viscosities resulting from the prediction method. In addition, the published viscosities of 64 multicomponent mixtures were compared with the corresponding calculated viscosities.

Altogether, the viscosities of 136 multicomponent, non-polar, gaseous mixtures were compared. The mixtures contained from 3 to 7 components including 16 different gases in the temperature range from 5• to 1014 ° c, and at a …

A Study Of Rotational Critical Speeds For A Multi-Mass System By Influence Coefficients, Kantikumar G. Patel

Masters Theses

"In this investigation an attempt has been made to determine the critical speeds of a multi-mass rotational system by using influence coefficients. Modes of vibrations are also examined at these critical speeds.

A shaft carrying five masses, supported by bearings at the ends, has been studied analytically. The length of the bearings is considered small with respect to the shaft length and therefore, the configuration is assumed to be point supported as a simple beam. The five masses, each weighing one pound, were placed at equal distances of 10 inches on a 60 inch shaft. The critical speed was examined …

A Laboratory Model Study Of Fluid Cross Flow., James Gary Fore

Masters Theses

"A procedure for scaling and operating a laboratory model for the purpose of studying fluid crossflow between zones of different permeability is presented. A modified existing model is used to simulate conditions for three dimensional, incompressible, two-phase flow through a two-layer, unconsolidated, homogeneous porous medium.

Eight tests were made to show effects on crossflow between the zones. Qualitative results indicate crossflow from the high to the low permeability zone for various perforation ratios and mobility ratios"--Abstract, p. ii

Effect Of Poly-Ethylene Glycol, A Non-Shrinking Agent, On Strength Properties Of Concrete., Vasantrai Vallabhbhai Desai

Masters Theses

"This thesis describes laboratory test made on plain concrete cylinders and ~earns for compressive strength, flexural strength, durability and shrinkage, using poly-ethylene glycol (ElOOO) as a non-shrinking admixture. The tests were conducted in the Materials Laboratory of the Civil Engineering Department.

The test results show that poly-ethylene glycol has the effect of reducing the compressive and flexural strength of plain concrete. The admixture also has the effect of reducing shrinkage, and reversing it, causing expansion with large percentage of its use. For the number of cycles of alternate freezing and thawing reported the admixture did not have any effect on …

Study Of The Temperature Dependence Of The Haeffner Effect In Mercury, Charles George Arnold

Masters Theses

“In 1953, E. Haeffner (1) reported that after he had passed a direct electric current through a capillary tube filled with mercury, he obtained a separation of the isotopes of mercury. It was found that the heavier isotopes were enriched at the negative terminal and the lighter Isotopes at the positive terminal. This effect has since been referred to as the Haeffner Effect. Since this original experiment, other investigators have observed this effect in many other liquid and some solid metal systems.

The work of J. N. Baysden (2) showed that the separation of the isotopes in mercury could be …

A Rubber Membrane Analogy For The Study Of Shafts In Torsion., Myron D. Bruns

Masters Theses

"The thesis presents a review of literature giving reference to several books which present the many and varied methods of determining the shearing stresses in shafts. However, no reference was found that used a rubber membrane analogy similar to that used in th is thesis. The theory of torsion, the membrane theory, and its analogy have been presented for a better understanding of the subject. Illustrations are used freely for clarity.

Analytical methods and solutions are given for two problems. The first method is that of writing a Saint-Venant stress function and satisfying the necessary conditions for it to be …

Use Of Sr-4 Strain Gages Under Hydraulic Pressure, Manubhai M. Patel

Masters Theses

"In this investigation an attempt has been made to determine the effects of hydraulic pressure on SR-4, type A-5 strain gages. A thick-walled aluminum alloy cylinder without end constraint was used to make an experimental study of the effects of hydraulic pressure on these strain gages.

The behavior of this cylinder under different internal hydraulic pressures was also studied by measuring the strains by means of strain gages which were attached to the inside and outside surface of the cylinder. The problem has been studied by applying pressures up to 4800 psi.

Because of the high internal fluid pressures various …

The Effect Of Metallic And Inert Electrodes On The Electrochemical Degradation Of Alkyl Benzene Sulfonate., Thomas Patrick O'Farrell

Masters Theses

"The purpose of this study was to investigate the effects of various metallic and inert electrode combinations on the electrochemical degradation of alkyl benzene sulfonates (ABS) in water and to determine the rate and degree of AB3 removal.

Selected combinations of copper, aluminum, iron, and carbon plate electrodes were studied in systems of tap, distilled and river waters containing an initial ABS concentration of 10 mg/1, using a current density of approximately 0.5 milliamperes per square centimeter and a total detention time of 6 hours. Samples were collected at appropriate time intervals and were analyzed for ABS, chemical oxygen demand …

Stability Investigation Of Pipe-Line Suspension Bridges, Ten-Hsi Chen

Masters Theses

“This thesis presents an analysis of the behavior of pipe line suspension bridges under the action of wind. From this analysis a differential equation of vertical vibration is derived and solved, and the possible methods of preventing its vibration are discussed and suggested”--Abstract, page ii.