Digital Commons Network^™

Application Of The Photoelastic Coating Method To Evaluate The Stress Distribution On The External Surface Of The Cap Of An Electrical Insulator, Harijeetsinh Jagtiani

Masters Theses

"The Photoelastic Coating Method was applied to find the surface stresses on the cap of an electrical insulator. The strain distribution was observed and photographed. This color photograph indicated a visible geography of the maximum shear strain distribution in the region of the insulator where the birefringent plastic was bonded with a reflective cement. The Oblique Incidence technique was used to determine the principal stresses from the maximum shear strain (or the principal strain difference) readings, obtained from Normal Incidence. The critical cross-section of the insulator head was optically located, giving an initiative for the re-design of the insulator cap. …

Instrumentation Of A Diesel Engine For Measuring Cylinder Head Temperature, And Pressure At Various Crank Angles, Raman A. Patel

Masters Theses

"In this investigation, an attempt has been made to measure the instantaneous pressures in the cylinder and the transient temperatures of cylinder head versus crank angle in a Diesel engine. A strain-gage pressure transducer and a sensitive surface thermocouple were used. The pressure transducer was practically free from temperature influence and strain effects caused by installation. It had a greatly reduced sensitivity to vibrations compared with other available types of pressure transducers. The thermocouple had a very short response time. A device enabling very accurate measurement of crank-angle was constructed. Appropriate quantities were displayed on the screen of an oscilloscope …

An Evaluation Of The Feasibility Of Neutron Microradiography, Maynard L. Arment

Masters Theses

"The metal working industry has used metallography and microradiography extensively in the past decade. X-ray or gamma microradiography has several advantages as compared to metallography, but a disadvantage concerning alloys of adjacent elements; microradiography cannot distinguish between elements 2 or less atomic numbers apart. Attempts were made using neutron microradiography to distinguish between cadmium and tin rich grains. A maximum resolution of 0.017 inches was found with a calculated possibility of a resolution less than 0.002 inches"--Abstract, page ii.

Study Of Deformation Of Non-Oscillating Droplets In Liquid Media, Arun Kumar Agrawal

Masters Theses

"The object of this investigation was to find a method for predicting the deformation of non-oscillating liquid droplets which are moving in liquid media, from a knowledge of droplet size and the physical properties of the continuous and dispersed phase systems. The deformation of thirteen liquid-liquid systems was experimentally studied in this investigation"--Abstract, page i.

Free Convection Heat Transfer From An Inclined Heated Flat Plate In Air, Shu Chien Yung

Masters Theses

"An experimental investigation has been performed to determine the free convection heat transfer from a heated flat plate in air moved from the vertical position through three inclined positions to the horizontal position. The hot surface of the plate was facing downward for the horizontal and three inclined positions. Tests were performed at plate surface temperatures from 120°F up to 404°F. Data for the plate surface temperature at about 165°F with the plate in the vertical position agrees very well with previous experimental work. This same data was used to determine a new parameter, introduced into the Pholhausen free convection …

An Apparatus To Measure Capillary Jet Thrusts And The Evaluation Of Normal Stresses In Fluids, Charles Donald Green

Masters Theses

"The purpose of this work was to design, construct and calibrate simple, inexpensive apparatus which could be used to measure the normal stresses and tangential shear stresses of a fluid. For normal stress measurements, the capillary jet thrust principle was selected. A standard analytical balance was modified so that capillary tubes could be fitted on it horizontally. It was designed so that the thrust produced by a jet of fluid from the tube caused a deviation from the zero balance position. The weights needed to rezero the balance gave a measure of the thrust"--Summary, page 1.

Order-Disorder In Fe₃Al At Various Temperatures Induced By Neutron Irradiation, Robert F. Toma Jr.

Masters Theses

"Resistivity measurements were made on ordered and disordered Fe₃Al samples while irradiated by neutrons.

In the ordered as well as the disorder state, the different Fe₃Al samples were heated to 100, 150, 200, 250, and 300°C respectively, and were irradiated by a fast neutron flux of 0.534 x 10¹⁰ neutrons/cm²-sec. The ordered Fe₃Al measurements were characterized by an increase in resistivity denoting an advancement toward disorder. The disordered Fe₃Al measurements were characterized by a decrease in resistivity denoting an advancement toward order. In the Fe₃Al ordered and disordered samples …

Circular Polarization From A Corner Reflector Antenna With Tilted Dipole Of Arbitrary Length, Ruben A. Carrizo M.

Masters Theses

"The problem consists of the development of the electric far field equations for a forty-five degree corner reflector antenna with a tilted dipole, of arbitrary length, centered at the corner bisector plane to produce circularly-polarized radiation. The far field expression was developed as a function of the spherical coordinate system variables and placed in Fortran language in order to determine the dipole locations which would produce circularly-polarized radiation. At such dipole locations the field patterns were plotted in the [theta] = [pi]/2 and [phi] = 0.0 planes. Computations were made by the IBM 1620 digital computer"--Abstract, page ii.

On Time-Optimal Second Order Discrete Control Systems, Chao-Tai Li

Masters Theses

"The time optimal control problem in unforced discrete systems is studied in this thesis. Comparison is made between the discrete and the continuous control systems by means of minimum time isochrones. concerning optimal time, it is shown that using the discrete control system will take at most one more sampling period of time to go to equilibrium. An investigation is also made for the case when the time constant of the physical plant, G(s), and the control model are different. In such a case, an optimal trajectory can not be obtained. An adaptive process is proposed to adjust the model …

The Shear Graph And Cohesive Soil, Charles Rees Nickerson

Masters Theses

"Some existing test procedures for measuring shearing properties of soils are reviewed. the correlation between the shear strength of two fine-grained soils as indicated by the unconfined compression test and the shear graph test is investigated. This is accomplished by comparing the test results at varying moisture contents and dry densities. One of the soils used is a red plastic clay, the other a silty clay. The test results indicate that for soils wet of optimum the shear graph strength can be taken as being equal to the unconfined compressive strength. This will be conservative for soils that exhibit an …

A Study Of Degradation In The Pumping Of Dilute Polymer Solutions, I-Chung Chang

Masters Theses

"In the course of an investigation of the turbulent flow properties of dilute high polymer solutions in organic solvents, a number of supplementary investigations were required. These were: 1. Determination of the molecular weights of a number of polymers by intrinsic viscosity measurements. 2. Determination of the effect of pumping on the degradation of high polymers in dilute solutions. This included development of a method for estimating the concentration of dilute polymer solutions. 3. Determination of the effects of density, viscosity and non-Newtonian behavior on the calibration of turbine flow meters"--Introduction, page 1.

The Dissolution Of Magnesium In Strong Acids And Neutral Solutions, Cheng-Ken Chi

Masters Theses

"The increasing demand for magnesium and magnesium- base alloys in the manufacture of aircraft has stimulated a great amount of research into the corrosion characteristics of these materials. The result of such research has been the development of suitable magnesium alloys and protective coatings to retard corrosion.

The basic mechanism of the anodic dissolution of metals such as magnesium, zinc, and cadmium in salt solutions is not completely known. Several schools of investigators have proposed different and opposing theories to explain the discrepancies which often arise between coulometer data and the weight loss of metal electrodes in certain salt solutions. …

A Computer Approach To Transistor Circuit Design, Kwok Chee Hong

Masters Theses

"The design of amplifiers is usually approached through experimental study. This thesis proposes a mathematical approach, using a digital computer to predict the performance of an active transistor circuit (a frequency equalizer circuit to compensate for the RIAA recording frequency characteristics) prior to the actual construction of the physical system. The simple but powerful computer analysis method will be based upon the nodal equations of the complete circuit. The primary aim is to design a circuit which would give a desired frequency-gain characteristic. The complete set of simultaneous complex nodal equations describing the circuit operation is then written. Based on …

The Cementing Of Hydraulically Placed Tailing Fill By The Oxidation Products Of Pyrrhotite, Stanley H. Alder

Masters Theses

"This thesis has been prepared to make available basic information on the use of the oxidation products of pyrrhotite to cement hydraulic tailing stope fill. As nothing has been published on this subject to date, a review has been made of pertinent information culled from accounts of work in related fields. From this study, a set of equations representing the most likely pyrrhotite oxidation reactions has been evolved and tests supporting these equations performed. Samples of fill, each containing from one to six percent of pyrrhotite, were cemented in the laboratory. They were then examined microscopically, subjected to unconfined compressive …

The Design And Construction Of A Shock Tube Facility, William Adolph Crede

Masters Theses

"It is the object of this thesis to give an account of the considerations necessary to design, construct, and operate a shock tube facility.

The primary purpose of the facility was to provide a means to study high strength shock waves in physics, chemistry, and aerodynamic applications.

Preliminary designs were undertaken to determine the basic dimensions and related capabilities. Final design, construction and testing of the tube itself was performed by Nooter Corporation in St. Louis, Missouri. Preliminary designs agreed rather closely with final construction.

Experimental testing was confined to the successful operation of all the various components of the …

Anodic Dissolution Of Silver In Aqueous Solutions, Jagdish Shantilal Sanghvi

Masters Theses

"Silver and platinum, although not used extensively in industry, find considerable use in specialized work. Silver, because of its much lower cost, is used to a greater extent than platinum. Since silver has a high position in the electromotive series, it is very resistant to chemical attack. It is unaffected by alkaline conditions even at high temperatures and hence silver is used in ladles and molds for producing pure sodium and potassium hydroxides. This and its excellent electrical conductivity makes it a very useful material in circuitry.

It has been reported in the literature that when active metals such as …

The Effect Of Carbonate Karst Terrain On Water Quality, Robert Russell Kilgo

Masters Theses

"The ever increasing use of water and unabated pollution of streams have made necessary increased research efforts into the quality and quantity of the available national water resources. Karst terrain is prevalent in several sections of the United States, however, little work has been done on the effect of this topography on water quality.

The purpose of this investigation was to determine the effect of carbonate karst terrain on the quality of water. The Meramec spring area, east of Rolla, Missouri, was selected for study. This area was underlain with dolomite formations and contains both karst and non-karst drainage basins …

The Electrochemical Oxidation Of Crotonic Acid, John L. Cannaday

Masters Theses

"The purpose of this investigation was to explain the mechanism of the electrochemical oxidation of crotonic acid on platinized-platinum anodes at 80⁰C.

A current-potential study was conducted using the parameters of pH and crotonic acid concentration. Faradaic efficiency was determined by measurement of CO₂ production.

Oxidation occurred both in acidic and basic solutions.The Faradaic efficiency was approximately 100 per cent.

The results were interpreted in terms of a mechanism having the following characteristics.

(a) The first charge transfer is the rate determining step.

(b) The rate is the sum of the rates for two parallel reactions. In strongly acidic solutions, …

Mass Transfer In The Electrodialytic Desalination Of Brackish Water And A Correlation Of Experimental Data With Theory, James Shih-Jiann Yang

Masters Theses

"The object of this work is an experimental investigation into the possibility of obtaining an increase in mass transfer in the electrodialysis of brackish water by altering the physical character of the selective membrane, and a correlation of experimental mass transfer data with theory"--Introduction, page 1.

Warping And Curling Of Plain Concrete Slabs, Vipinbhai Ratilal Shah

Masters Theses

"The study was made to determine the effect of daily atmospheric temperature variation and curing on the warping and curling of plain concrete slabs and to study the effect of moisture on the warping of plain concrete slabs under nearly constant temperature conditions, by keeping the bottom surface of one slab wet and the other dry.

Daily observations consisted of dial gage readings to determine the progressive variations in warping contours due to typical daily temperature curling. Trends were found for three months of dial gage readings and interpreted in terms of warping and curling of the slabs.

The warping …

A Study Of The Non-Newtonian Turbulent Fluid Flow Through An Annulus, Yogesh R. Parikh

Masters Theses

"This investigation is concerned with the study of non-Newtonian flow through an annulus. The experimental analysis of incompressible non-Newtonian fluids in a long cylindrical annulus of radius ratio 0.375 was studied in the turbulent region. Different types of non-Newtonian fluids were used to procure flow behaviour for the annulus.
The effect of increasing flow rate of the non-Newtonian fluids was evaluated by gathering pressure drop data across the annulus using a differential manometer. The power-law model is used in this study to characterize the non-Newtonian flow. The parameters of the power-law model were evaluated by gathering viscometric data on a …

The Design And Construction Of A Medium Power, Synchronous, Electronic Switch, Floyd S. Hall

Masters Theses

"This paper presents the design and construction of a medium power, synchronous, electronic switch and associated timing and control circuits.

The unit described is capable of controlling a 20 ampere resistive or inductive load from a 110/220 volt, 60 Hz excitation source. Thyristors are used as the active switching elements. The period of the on/off switching cycle may be varied from 1/60 second to 8 1/2 seconds. Turn-on and turn-off may occur at independently selected phase angles relative to the reference frequency source.

Higher power operation could be obtained easily with minor design changes"--Abstract, page ii.

Optimization Of Flywheel Design For Internal Combustion Engines, Dady Jal Patel

Masters Theses

"A new approach to the problem of flywheel design has been developed, thus eliminating some of the problems of conventional design. The term flywheel design, in this thesis, refers to the determination of the flywheel inertia (mass moment of inertia) only. Two versatile computer programs were set up to obtain the flywheel inertia and the turning moment diagram for a large variety of internal combustion engines, and use was made of these programs to optimize the inertia of the flywheel with respect to speed. As an illustration the data of a 1960 Corvair engine were selected, and the results obtained …

Analysis Of Flat Slabs With Various Edge Supports, Wu-Mo Chern

Masters Theses

"This study presents the solution of flat slabs with various edge conditions including T-Beam edge supports, The equations formulated are based on the finite difference method and solved using an electronic computer.

The results indicate that the solution of these slabs by the finite difference approximation is a practical method. In addition, this method is more flexible and yields moment values that are considerably more accurate than those obtained using the ACI Code"--Abstract, page ii.

The Development Of Conical Stress Forms By Explosive Charges, Walter T. Casquino

Masters Theses

"Usually stresses generated by explosive charges during blasting are considered to propagate through materials in a spherical manner. Although conical stress waves had been suggested by a few investigators they have never been clearly defined or studied in the laboratory.

An experimental technique using models was developed to produce conical stress waves from an explosive. Several materials with different properties were selected as models for the purpose of determining whether or not conical waves could be generated in all materials.

This investigation showed that conical stress waves do exist under certain conditions, which would closely approximate those present for much …

The Influence Of Cation Exchange And Electrolyte Concentrations Upon The Atterberg Limits, Kent J. Schwieger

Masters Theses

"The object of this investigation is to correlate relationships between cation exchange capacity, clay content, and type and concentration of the exchangeable cations upon the Atterberg limits of a soil. Synthetic soils consisting of loessial silt and either an illitic natural deposit, bentonite, ball clay, or kaolin clay were used.

As the percent clay fraction was increased the cation exchange capacity, liquid and plastic limits and plasticity index increased linearly in the clay range. Results also suggested a linear relationship between the liquid and plastic limits and the cation exchange capacity of soils of one hundred percent clay fraction"--Abstract, page …

Hot Isostatic Compaction Of Graphite, Donald C. Carmichael, P. D. Ownby, Edwin S. Hodge

Materials Science and Engineering Faculty Research & Creative Works

The effects of temperature, pressure, and graphite starting material on the density, isotropy, and strength of dense graphite material prepared by hot isostatic compaction of graphite powders were examined. Process equipment was developed to permit operation at temperatures up to 2700 C under a 1600-atom isostatic pressure of inert gas . The isotropy of graphite compacts was determined by neutron diffraction. Relatively isotropic, high-purity graphites were produced having modest isotropic tensile strength and extremely high density (up to 2.24 g per cm³, or 99 per cent of theoretical).

Design Of Non-Uniform Linear Antenna Arrays With Digitized Spacing And Amplitude Levels, Jack F. Morris

Masters Theses

"Recent developments in space exploration have shown a need for high resolution, high gain antennas. The introduction of non-uniform linear array theory has provided a means by which arrays may be designed to produce narrow main beams with fewer elements than required by uniform arrays. A general theory has not been developed, however, and the design engineer has been left with only trial-and-error methods with which to work. In this study a technique has been developed by which non-uniform antenna arrays may be synthesized to meet a given set of specifications with reasonable accuracy. The elements of the array are …

An Investigation Of Continuous Prestressed Concrete Structures, Ping-Chi Mao

Masters Theses

"This thesis presents an analysis of the behavior of continuous prestressed concrete structures. From this analysis the governing equations for various types of geometry for prestressing cables are derived. The calculation of fixed-end moments due to the prestressing force using the equations derived is quite cumbersome, however, in order to simplify the calculations, design charts are developed. A cable with reverse curvature is analyzed using the design charts. It is shown that the fixed-end moments calculated by neglecting the effect of reverse curvature differ significantly from the fixed-end moments calculated by considering this effect. Hence the effect of reverse curvature …

Evaluation Of Pile Bearing Capacity By Use Of The Wave Equation, Stuart H. Williams

Masters Theses

"The wave equation method of evaluating pile bearing capacity is investigated by using data obtained from a comprehensive pile testing program. Modifications which create a more accurate and realistic approach are made to the method proposed by previous investigators. With the use of these modifications, correlation between observed and computed results is more readily obtained. Selected pile formulas in the empirical, static, and dynamic categories are reviewed so that a direct comparison between these and the wave equation method can be made"--Abstract, page ii.