Digital Commons Network^™

Electrodialysis Of Tomato Juice, Raghunath R. Khetan

Masters Theses

"Thermal decarboxylation of carboxylic acids has been helpful in illustrating some fundamentals of reaction kinetics in solution. It has been important in formulation of the theory of unimolecular reactions. It is also used frequently in the synthetical methods of organic chemistry.

In a recent study of the anodic oxidation of malonic acid in sulfuric acid at 80⁰C using a platinum anode, the interpretation of some results was impossible due to the spontaneous decomposition of the malonic acid. As no information is available in the literature about decomposition rates of malonic acid in sulfuric acid at the concentrations used, it was …

Mass Transfer In Droplets With Turbulent Internal Circulation - Mathematical Description, Jayantilal Mohanbhai Patel

Masters Theses

"This investigation was carried out to check the accuracy of the eigenvalues, λ_n, calculated by Wellek and Skelland, using some method other than the Rayleigh-Ritz technique and also, to determine the coefficients, B_n in series solution, which were not calculated before.
The eigenvalues were obtained by trial and error procedure using the standard Runge-Kutta method. The coefficients B_n were obtained by using eigenvalues. By using this information the fractional extraction was calculated as a function of droplet contact time.

The Wellek-Skelland modification was also solved by finite difference technique to compute fraction extracted as a function …

Nucleate Boiling Heat Transfer To Liquid Nitrogen At Atmospheric Pressure, Satish R. Parikh

Masters Theses

"The object of this investigation was to study the effect of micro-roughness, a thin layer of oil, and infra-red radiations on the cylindrical heat transfer surface of copper, in liquid nitrogen and at atmospheric pressure during nucleate boiling. An attempt was made to find any possible effect of orientation of the heat transfer element on nucleate boiling. A number of different runs were taken with different degrees of roughness, and different orientation positions. Nucleate boiling has been found to be nearly independent of the heat transfer surface roughness and of orientation while strongly dependent on the chemical nature of the …

An Ac Method Of Measuring The Conductivity Of Dielectric Liquids., Henry E. Fischer

Masters Theses

"The problem undertaken in this thesis is the presentation of a method of measuring the conductivity of dielectric liquids in which the liquid is used as the parallel tank circuit of a modified Wien-bridge oscillator. The main advantage of this method is that the frequency of the voltage applied to the liquid can be varied by simply varying the oscillator frequency. This allows the selection of a frequency which is best suited to the liquid in regard to polarization and relaxation time.

An oscillator was designed, built and used in the laboratory to measure the conductivity of the dielectric liquids …

Analysis Of Time-Varying Linear Multipole Filters With Sampled Nonstationary Random Inputs, Ming-Chwan Chow

Masters Theses

"In this thesis an analytical method is developed to determine an optimum time-varying linear filter in order to satisfy the following specifications. The filters are of sampled data multipole form with n inputs and m outputs. The signal of each input is a member of a nonstationary random process, and the signal is corrupted by stationary noise.

The statistical optimization theory developed by Wiener is extended to a linear time- varying filter with nonstationary input. Correlation functions are defined for nonstationary ensembles. The mean- square error is calculated in terms of these correlation functions. By minimization of the mean-square error, …

The Effect Of Structure On The Consolidation Characteristics Of A Clay Soil, Dale E. Sukow

Masters Theses

"This paper reports the results of an investigation conducted to establish the effect of structure on the consolidation characteristics of a clay soil. Soil structure was caused to form in the soil by the addition of electrolytes to flocculate and disperse the clay fraction of the soil.

Consolidation tests were performed on specimens of the treated soil prepared at moisture contents well above the liquid limit of the soil. The consolidation data from these tests are evaluated and comparisons are made to relate the influence of structure to the consolidation characteristics of the treated soil.

The influence of structure on …

An Application Of The Variable Gradient Method Of Generating Liapunov Functions To Discrete Systems, Henry N. Peterson

Masters Theses

"The variable gradient method of generating Liapunov functions has been used only for continuous systems. This thesis presents an application of the variable gradient method to non-linear sampled data control systems.
Certain modifications to the variable gradient method are developed and several examples are presented which demonstrate the application. An attempt was made to synthesize the control system parameters, but due to the complexity of the ΔV functions, the synthesis in general cannot easily be obtained . To circumvent the problem of determining if the ΔV functions are negative definite, a set of computer programs were written to determine a …

A Mathematical Study Of Voigt Viscoelastic Love Wave Propagation, David Nuse Peacock

Masters Theses

"This research is a mathematical investigation of the propagation of a Love wave in a Voigt viscoelastic medium. A solution to the partial differential equation of motion is assumed and is shown to satisfy the three necessary boundary conditions. Velocity restrictions on the wave and the media are developed and are shown to be of the same form as those governing the elastic Love wave"--Abstract, page ii.

Study Of Heat And Mass Transfer Through Non-Wettable Porous Membrane, Rajender Kumar Rohatgi

Masters Theses

"The object of this investigation was to study the use of non-wettable porous membranes for simultaneous heat transfer and mass transfer of water from a hot salt solution stream to a cold distilled water stream, the streams being in countercurrent flow separated by the membrane. This type of mass transfer was achieved in the experiments, and mass and heat transfer coefficients were measured.

The membranes studied in this work were made of fiberglas treated with Teflon dispersion and aluminum sulphate. The fiberglas membranes yielded desired results. Empirical correlations were proposed which predict values of heat and mass transfer coefficients close …

Calibration Of An Instrument To Calibrate Accelerometers, Nader Khorzad

Masters Theses

"The purpose of this research was to calibrate an instrument with which an accelerometer could be calibrated accurately. The instruments used were a piezoelectric shaker and a modified Michelson interferometer together with necessary electronic equipment. This equipment was used to calibrate a Kistler Model 808A accelerometer.

Weight was added to the shaker in the second part of this experiment in order to determine its effect on the amplitude and frequency of oscillation of the shaker.

Results show that this instrument may be used to calibrate an accelerometer quite accurately. The weight added to the shaker will effect only the amplitude …

Temperature And Stress Distributions Produced In Long Circular Cylinders Cooled By Emission Of Thermal Radiation, Robert S. Pritchard

Mechanical Engineering ETDs

This study involves the determination of the temperature and stress distributions produced in long circumferentially symmetric circular cylinders cooled by emission of thermal radiation from the lateral surface. Temperature and strain responses obtained from an experimental model are presented for a set of parameters which correspond to the highest strain level which could be accurately determined with the strain gages. These responses are in good agreement with the results obtained by solution of an appropriate mathematical model. Temperature responses obtained from the same model, but having a higher initial temperature, are also presented and compared with analytical results. Reasonably good …

Torsional-Flexural Buckling Of Thin-Walled Open Sections, Pen J. Fang, George Winter

CCFSS Library (1939 - present)

INTRODUCTION Compression members with thin-walled open sections, because of their low torsional rigidities and because their cross-sectional configuration is such that the centroid and the shear center often do not coincide, can buckle at loads well below the Euler load by interaction of torsion and bending. Fast expanding applications of such sections in civil and architectural engineering call for an extensive investigation of torsional-flexural buckling. Basic theory of torsional-flexural buckling is treated by a number of authors, I,2 and simplifications of the basic theory in the elastic range for the design purposes together with some test results were reported previously. …

The Irish Plumbing And Heating Engineer, November 1965 (Complete Issue)

Building Services Engineering

No abstract provided.

Strength Of Three New Types Of Composite Beams, A. A. Toprac

CCFSS Library (1939 - present)

No abstract provided.

The Performance Of Beams And Columns Continuously Braced With Diaphragms - I, Gordon P. Fisher, S. J. Errera

CCFSS Library (1939 - present)

When properly attached, shear-rigid light-gage metal diaphragms, such as roof decking or wall sheathing, can be very effective as lateral bracing for slender columns and beams. At present, limited design use is made of this fact, because of inadequate information on the effectiveness and reliability of such bracing. In this thesis, previous theory on the stability of Isection beams and columns braced with shear-rigid diaphragms has been extended. Two energy methods are used, one employing the Euler-Lagrange conditions from the calculus of variations, and the other the Rayleigh-Ritz method. The problem initially considered is that of an I-section beam-column eccentrically …

Galvanomagnetic Effects And Related Phenonmenon In Semiconductors And Dielectrics In A Radiation Environment, Leroy C. Meyer

Electrical and Computer Engineering ETDs

From Introduction:

In 1878, Hall found that the stream lines of an electric current in a metallic conductor were distorted when the conductor was placed in an external magnetic field. This distortion arises from an electric field set up at right angles to the current and to the magnetic field. The effect is well known in conductors and semiconductors, for both steady state and low frequencies Figure 1-1 illustrates the polarities of the Hall voltage for Ix in the direction of conventional current flow.

Drag Forces On Magnetically Accelerated Particles, Darrell Winterton Walker

Theses and Dissertations

The object of this investigation was to determine the effect of acceleration on the drag of spheres as it differs from the steady state case. Steady state drag applies to the force acting on a single sphere moving at constant velocity through an infinite, continuous, incompressible, turbulence free fluid. Extensive experimentation has quite thoroughly documented the steady state drag characteristics of spheres. A dimensionless parameter associated with the drag force is sometimes used to correlate drag characteristics.

Heat Transfer In Shock Boundary Layer Interaction Regions, Rex W. Shumway

Theses and Dissertations

The interest in aerodynamic heating problems has been increasing rapidly in the last decade. This interest is no longer concentrated on the heating of simple shapes for which adequate heat transfer theory has been developed« Because of the increasing Mach number ranges of aircraft, the need for information on the aerodynamic heating of various components has become imperative. Only when the magnitude of the problem has been exposed can the design for reducing the severity of local heating be optimized. Definition of these problems is of interest, not only because of the flow phenomena, but because of possible design limitations …

The Investigation And Design Of A Powered, Single-Man Parawing Aircraft, Calvin J. Merrell

Theses and Dissertations

During the last few years there has been an increasing interest in a high-lift wing configuration known as the flex-wing, or parawing. The parawing consists basically of a flexible membrane such as cloth, attached to two leading edges (or booms) and a keel as shown in Figure 1. At angles of attack (��) greater than the billowing angle (��). the air impinges on the under side of the membrane and forces it into a double-arch shape at each cross-section. When straight leading edges are used, each arch approximates the shape of a conical section. A cylindrical section is obtained by …

Turbulent Flow In The Entry Region, Chin-Hsiu Li

Theses and Dissertations

When entering into the subject of turbulent flow, it is essential to understand that the kind of flow with which we deal belongs to a particular class known as shear flow. These types of flow comprise flow fields in which relative velocities have been induced by shear stresses rather than by the action of pressure forces. In pipe flow, when the fluid enters through the well-rounded bell from a reservoir or from the calm open air, a uniform velocity distribution occurs at the pipe entrance. Immediately down stream from the entrance of the pipe, the flow is structured with a …

The Vibration Response Of Laminated Orthotropic Plates, Max E. Waddoups Jr.

Theses and Dissertations

The behavior of anisotropic materials has been the object of much recent research® The high strength to weight ratio needed by aerospace structures has necessitated the use of exotic, composite materials which generally exhibit anisotropic behavior® These materials cannot be fully utilized unless analytical techniques are used which take maximum advantage of their anisotropic behavior.

Structural Performance Of Light Gage Steel Diaphragms, Larry D. Luttrell, George Winter

CCFSS Library (1939 - present)

Light gage steel roof, wall, and floor systems may be used to transfer in-plane shear forces from one part of a framed structure to another, leading to reduced loads in parts of the structure. This is particularly noticeable in buildings having rigid end walls and under lateral loading. The diaphragms transfer forces from the interior frames into the foundation through the rigid end walls, resulting in lower loads for the interior frames. The amount of force transfer is dependent upon the in-plane shear strength and is particularly sensitive to the shear stiffness of the diaphragm. The results from some 60 …

Torsional-Flexural Buckling Of Thin-Walled Open Sections, Pen J. Fang

CCFSS Library (1939 - present)

No abstract provided.

Liquid Particle Interaction With A Normal Shock Wave, Victor George Forsnes

Theses and Dissertations

The atomization of a liquid by an air stream has been an item of much concern in the past, and there have been numerous experimental studies of the process made in an effort to correlate liquid and air- stream physical properties into a general model which will predict the degree of and the time required for atomization for a given physical situation. The breakup of liquid drops, a major portion of the atomization process, finds application in the field of meteorology, where the formation, breakup, and shape of raindrops is an item of much concern; in the field of internal …

The Irish Plumbing And Heating Engineer, July 1965 (Complete Issue)

Building Services Engineering

No abstract provided.

Effects Of Cold-Forming On Light-Gage Steel Members, Kenneth W. Karren, George Winter

CCFSS Library (1939 - present)

Cold-forming may cause significant increases in tensile and in compressive yield strength in both the corner and flat elements of light-gage cold-formed steel members. The cumulative effects may raise the yield strength to as reuch as 70% above the virgin yield strength of the as-rolled sheet steel. The yield strength of corners is always considerably higher than that of any other portion of a cold-formed member because of the large plastic deformations which take place in the corners. Thus compact members with a large ratio of corner area to cross sectional area will have the largest increases in yield strength. …

Residual Stresses And The Bauschinger Effect, Raymond M. Huebner

Theses and Dissertations

Within the last ten years there has been much interest in the field of elasto-plastic behavior of engineering materials. Hie recent popularity of the low-cost light-weight plastically designed structures has added a great deal of impetus to this interest. This thesis deals with one of the aspects of elasto-plastic behavior, namely, the distribution of the residual stresses in a simple member which has been plastically deformed in tension and/or compression,. In particular, an attempt has been made to relate these residual stresses to the well-known but little understood Bauschinger effect.

An Investigation Of The Need To Correlate Academic Subject Areas With Industrial Arts, Ernest James Boedcher

Graduate Student Research Papers

This study was initiated as a result of a need that became apparent in two industrial arts seminars at Central Washington State College. Studies reveal that industrial arts teachers use principles, laws, and applications of mathematics and science daily, but these are seldom recognized and made meaningful to the students. As a result of this study industrial arts teachers may see a way to use this material to initiate similar situations in their teaching.

Residual Stress Distribution Changes During Dynamic Unidirectional Tensile Loading, Henry Swan Todd

Theses and Dissertations

In recent years there has been much engineering effort channeled toward obtaining higher strength, lower weight and cost product designs. In pursuit of this goal some carefully designed and tested parts have catastrophically failed after a long history of repeated successful service, even though the load at the time of failure was no higher than the part had repeatedly carried previously. These mechanical failures are commonly classified as fatigue failures.

Experimental Investigation Of Free Field Conditions In Tanks To Be Used In Interaction Studies, Clark P. Sanger

Civil Engineering ETDs

Experiments to determine the effects of boundary friction losses on static and dynamic vertical stress transmission and to determine the stress-strain relationship of standard 20-30 Ottawa sand in 8-inch-I.D. tanks to be used in burial structure interaction studies are presented. In these tests the tank height, boundary condition, sand density, and overpressure rise time were varied. The use of a greased rubber membrane proved to be a reliable method of minimizing the boundary friction losses thus creating a strain field that was independent of the tank height. Vertical stress transmission was not affected by the overpressure load rate. The stress-strain …