Digital Commons Network^™

Thermal-Fatigue Of Type 304 Stainless Steel, Gajinder Bir Singh Arora

Masters Theses

"Thermal fatigue resistance of unrestrained samples of type 304 stainless steel has been investigated under different test conditions. The following studies are reported: (a) effects of heating and cooling rates on the initiation of cracks, (b) effects of upper and lower cycle temperatures on the initiation of cracks, (c) effect of water quenching and (d) the manner in which cracks initiated and propagated. It is shown that under cyclic conditions involving maximum temperatures up to 1000°C, the thermal fatigue life of the material decreases rapidly with rise in the maximum temperature of the cycle. The increase in the lower cycle …

Further Investigation Of The Traveling-Wave Transistor, Robert J. Feugate

Masters Theses

"A brief introduction to the concept of a traveling-wave field-effect transistor is presented. Analytic solutions for certain lossless and lossy special cases are derived and a numerical method for solution of the general case developed. A possible computer program for implementing this numerically is given and utilized to compare the traveling-wave transistor to a conventional field-effect transistor amplifier"--Abstract, page ii.

The Effect Of Thermal-Mechanical Processing Of The Exfoliation Corrosion Resistance Of An Aluminum-Zinc-Magnesium-Copper Alloy, James Lawrence Spehr

Masters Theses

"The objective of this investigation was to evaluate the effect of thermal-mechanical processing on the exfoliation corrosion resistance of an aluminum-zinc-magnesium-copper alloy. the aluminum alloy used was commercially available 7178 alloy in two thicknesses, 0.390 inch thick and 0.250 inch thick. this material was reduced 10, 25 and 40% in thickness in both the annealed and solution heat treated conditions. The material was then aged to a high strength condition, T6, or T8, in the case of the material reduced in the solution heat treated condition. The effect of the thermal-mechanical processing on the exfoliation corrosion resistance was then evaluated …

An Investigation Of Transient Negative Resistance In A Cadmium Sulfide Device, John Irvin Giem

Masters Theses

"An analysis has been made of a CdS device which exhibits a transient negative resistance at room temperature and low field strengths whereas previously reported cases of negative resistance in CdS were observed at low temperatures and moderate to high electric fields. The CdS bar was illuminated on one end in the vicinity of an ohmic In contact. Contact was made to the other end of the device with a rectifying Ag contact and the device was reverse biased. Experimental evidence and the analytical results both indicated that it is necessary that the material used to make the negative resistance …

Solution Of The Two-Dimensional Multigroup Neutron Diffusion Equation By A Synthesis Method, William Ray Heldenbrand

Masters Theses

"A method, called the higher mode synthesis method, for the solution of the two-dimensional neutron diffusion equation is developed. In this method, the two-dimensional eigenfunction is expanded in terms of one-dimensional fundamental and higher eigenfunctions. A substitute, weight, and integration procedure is applied and the two-dimensional equation is reduced to a one-dimensional equation in terms of expansion coefficients. The expansion coefficients are combined with the trial functions in order to obtain the two-dimensional eigenfunction. This procedure results in a significant reduction of computation time as compared with standard iteration methods"--Abstract, page ii.

A Simple Observational Technique For The Investigation Of Boundary Layer Stability And Turbulence, Tony Maxworthy

Symposia on Turbulence in Liquids

A dense suspension of aluminum flakes in a fluid has many advantages as a flow-visualization method, and has been used to study circular Couette flow and Benard instability, among others. In the present contribution the scientific and pedagogical merits of the technique are examined further for three different cases: (a) Stability of Poiseuille flow; (b) Stability of the side-wall boundary layers created when a fluid-filLed, rotating container is suddenly brought to rest; (b) Stability of the boundary layer beneath a concentrated vortex.

The technique is also useful in other cases, especially when fundamentals of fluid flow are to be demonstrated …

Measurements Of Density Fluctuations In Submerged Water Jets, L. N. Wilson, D. W. Prosser

Symposia on Turbulence in Liquids

A remote sensing technique, free from many of the problems associated with Inserting probes into a liquid flow, has been developed to measure turbulent density fluctuations In a low speed, submerged water jet. The technique employs two schlieren optical systems, composed of He-Ne lasers and photo detectors. The optical beams intersect in the flow in a plane perpendicular to the flow direction. Knife edges are aligned such that the systems are sensitive to gradients of refractive index in the flow direction. An analysis is presented which relates the cross-covariance of the two signals to the local two-point refractive-index covariance and …

Conference Proceedings Of The Symposium On Turbulence Measurements In Liquids, September 1969, University Of Missouri--Rolla

Symposia on Turbulence in Liquids

No abstract provided.

Effect Of Dilute Polymer Solutions On External Boundary Layers, Brian Latto, J. A. Middleton

Symposia on Turbulence in Liquids

The paper reports an experimental study of the flow of homogeneous aqueous polyacrylamide MRL 402 solution over a thin flat plate. Extensive velocity profile data were obtained, using both cylindrical and conical hot-file probes, and used to obtain local skin friction profiles. Direct drag measurements were made over a period of time for concentrations of 0, 25, 50 and 75 wppm and indicated that there was no appreciable degradation of the polymer. Extensive turbulence intensity data were obtained which were contradictory but indicated that the conical type probe is better than the cylindrical type for turbulence measurements and that the …

Determination Of Distillation Efficiencies For The Water-Methanol-Acetone System, Chorng Shyong Wang

Masters Theses

"A pilot-scale, eight-plate, bubble-cap distillation tower with a multi-point temperature recorder and automatic sampling device was used to obtain operating data on temperatures and liquid phase compositions for distillation efficiency studies. The tower was run with a single feed, a total condenser, and a partial reboiler. At steady state, as indicated by constant temperatures, samples were taken and later analyzed by gas chromatography. A digital program was developed to calculate component efficiencies on each plate according to Holland's modified Murphree plate efficiency, utilizing the operating data, and reflux rate, the input and output flows and compositions, and vapor-liquid equilibrium data. …

Study Of Diagnosability Of Binary Address Decoders, Girishchandra Mahendrakumar Gandhi

Masters Theses

"This paper studies the diagnosability of various types of binary address decoders. An attempt is made to develop a theory of diagnosis for logical faults that might occur in these logic nets. The developed theory is used to analyze these logic nets for various input combinations. Finally, the derivation of optimum diagnostic test sequences is considered"--Abstract, Page i.

Investigation Of Free Convection Heat Transfer From An Inclined Flat Plate, Phairojna Sang-Urai

Masters Theses

"The experimental investigation was conducted to determine temperature distribution and convective heat transfer coefficients in terms of Nusselt number for an inclined heated flat plate in air. The heated surface of the aluminum flat plate was set facing upward and moved through seven positions from the vertical to the horizontal. The investigation shows that the local Nusselt number can be predicted by Kiekus's solution within 12 per cent for inclination angles from the vertical through 75° from the vertical. In the case of the vertical position, Eckert's solution gives a better prediction. For the horizontal position the results show good …

Application Of Approximate Transmission Matrices To Describe Transverse Beam Vibrations, Ranjit Kumar Roy

Masters Theses

"This paper is a report of an investigation of an approximate method for finding the principal mode frequency roots for beams in transverse vibration. The method utilizes approximate transmission matrices obtained by a power series expansion of the basic differential equation which governs the transmission matrix. Investigation has been carried out to examine the efficiency of the method in producing the first several normal mode frequency roots. This has been achieved by applying the method to several uniform and non-uniform beams and comparing the results with the exact solutions. The technique has further been applied to non-uniform beams of tapered …

Telecommunications System Design Considerations For Advanced Logistic Spacecraft, James Myron Romberg

Masters Theses

"The telecommunications system design goals and functional requirements for an advanced logistic spacecraft are presented qualitatively. Advanced equipment and techniques that meet these system requirements and goals, that are within the state-of-the-art and that are believed to be economically feasible, are enumerated and described. System emphasis is on unification to minimize RF links and antenna subsystems, and on use of functional redundancy to assure satisfactory performance of critical telecommunication functions. The interaction of the telecommunications system design and the spacecraft mechanical, environmental, electrical, and operational interfaces are described in qualitative and quantitative terms. A practical spectrum of system interface characteristics …

Anodic Behavior Of Semiconducting Insb Single Crystals In Acidic Solutions, Lih-Da Hu

Masters Theses

"Undoped, semiconducting single, n-type, InSb crystals were used to study the different etching behavior of the inverse {111} planes, to determine the apparent electron number of InSb under anodic dissolution (which corresponds to the sum of the absolute values of the oxidation numbers) and to investigate whether or not the inverse {111} planes show potential differences. The In {111}, Sb {111[repeating]}, {110} and {100} faces were highly polished, etched and immersed in various acidic solutions. Several new etch patterns of the inverse {111} faces were observed in giving other possibilities to distinguish both of the planes. The significant differences in …

A Study Of A Lead Mining Waste Water Pollution Problem, William Earl Anderson Jr.

Masters Theses

"The waste water from the Fletcher Mine of the St. Joseph Lead Company was producing large algal growths in Bee Fork Creek. A field and laboratory study was conducted to determine the characteristics of the waste, find a method of determining the pollutional materials contained in the waste, study the undesirable algal growths, and develop and evaluate a practical, inexpensive, and effective pollution abatement method. Laboratory studies included analytical analysis of the waste, flotation reagent analysis, a microscopic study of the algal growths, algal growth studies, and heavy metal analysis of the algal growths. Field work comprised: a study of …

A Five-Spot Waterflood Process As Applied To The Digital Computer Based On The Prats Technique, Leonard Koederitz

Masters Theses

"The technique for the prediction of injection rates and production history of a five-spot secondary recovery field pattern as presented by Prats has been significantly modified to permit rapid and accurate digital applications eliminating the heretofore prohibitive reliance upon electrolytic model results for intermediate data values following water front breakthrough"--Abstract, page i.

Numerical Simulation Of One-Dimensional Three-Phase Fluid Flow In A Stratified Petroleum Reservoir With No Cross-Flow, Ali Mohammed Akbar

Masters Theses

"A numerical model for linear, three-phase fluid flow in a stratified petroleum reservoir has been developed for the purpose of studying water-flooding performance characteristics. Gravity forces, capillary pressure and cross-flow were neglected, but the fluids were considered compressible and evaluations of dissolved gas concentrations have been accounted for. The model was used in evaluating the performance of a water flood project for a hypothetical reservoir which contained the three phases of oil, gas, and water. The results were then compared with those obtained using the Dykstra-Parsons technique. The model produces results which were found to be similar to those obtained …

Simulation Of The Cyclic Steam Injection Process In A Petroleum Reservoir By A Finite Difference Mathematical Model, Jean-Claude Bernys

Masters Theses

"A three-phase, one-dimensional radially layered reservoir simulator is programmed for a large memory digital computer. It is designed to provide a practical solution to the problem of determining optimum soak time during an intermittent steam injection process. The general approach is to (1) develop a representative mathematical model which describes the reservoir; and (2) employ a suitable numerical technique to solve the system of equations which comprises this model. The reservoir consists of concentric cylinders around the wellbore, a pay-zone stratified into thermally connected layers limited on the top and on the bottom by an impermeable cap and base rock, …

A Study Of The Correlation Potential Of The Optimum Moisture Content, Maximum Dry Density, And Consolidated Drained Shear Strength Of Plastic Fine-Grained Soils With Index Properties, Marvin Tartt Harris

Masters Theses

"The correlation potential of the compaction properties and the consolidated drained shear strength parameters of plastic fine-grained soils with index properties was investigated in this study. The interrelationships of these properties were derived through graphical and multilinear regression analysis. The compaction properties, optimum moisture content, and maximum dry density were found to be related to many of the index properties. The most important relationships were with the plasticity indices and the percentage of particles smaller than two microns; the highest degree of simple correlation was achieved with the liquid limit. The consolidated drained shear parameters, cohesion, and the angle of …

Isotope Effect Of Carbon Diffusion In An Fe-Si Alloy, Manfred Wuttig, E. T. Yen

Materials Science and Engineering Faculty Research & Creative Works

The isotope effect of carbon diffusion in dilute iron silicon alloys containing 28Si and 30Si has been measured below room temperature using the Dis accommodation technique. The time dependence of the reluctivity has been analyzed in terms of two relaxation processes which are due to the reorientation of carbon interstitials in Fe-Fe and Fe-Si sites respectively. The ratio of the relaxation times of the two carbon isotopes 13C and 12C τ13/τ12 is 1.037 for the former and 1.007 for the latter process in the Fe+28Si alloy. The ratios of the relaxation times of the same carbon isotope 12C contained in …

Film Boiling Heat Transfer From An Oscillating Sphere, L. G. Rhea, R. G. Nevins

Mechanical and Aerospace Engineering Faculty Research & Creative Works

An experimental investigation has been undertaken to determine the effect of oscillation of the heat transfer surface on turbulent film boiling heat transfer. A transient technique was used to calculate the heat flux from copper spheres of 1 in., 3/4 in., and 1/2 in. dia. In all tests, saturated liquid nitrogen at atmospheric pressure was used as the boiling fluid. The data obtained were found to be in good agreement with published theory at zero frequency. The range of frequencies studied was from zero to approximately 12 cps at peak-to-peak amplitudes of 2 in. and 1 in., i.e., at amplitude-to-diameter …

Methods For Evaluating The Performance Of Small Acoustic Filters, William S. Gatley, Raymond Cohen

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Experimental methods are needed for determining the characteristics of small acoustic filters used in systems with pulsating gas flows. These characteristics could then be used to predict the performance of proposed filter designs in a particular system, according to plane wave acoustic theory. Dependence on trial-and-error experimentation in solving noise control problems would thus be minimized. A literature survey revealed only a few earlier attempts to evaluate the acoustic performance of small filters and filter elements. Three methods for determining reflection and transmission factors are described, evaluated, and compared. A method employing a standing wave tube of unique design is …

Mutually Dependent Heat And Mass Transfer In Laminar Duct Flow, E. M. Sparrow, T. S. Chen

Mechanical and Aerospace Engineering Faculty Research & Creative Works

An analysis is performed of the strongly coupled heat and mass transfer processes which result from sublimation of mass from the walls of a duct into a flowing gas, the latent heat being provided solely by convective transfer from the gas. The flow is assumed to be laminar and hydrodynamically developed. Results are given for the stream ward variations of the bulk and wall temperatures and mass fractions, of the heat and mass transfer rates, and of the local heat transfer coefficient. Representative temperature and mass fraction profiles are also presented. Entrance lengths characterizing the near approach to fully developed …

The Influence Of Organic Matter On Shear Strength Of A Cohesive Soil, Kamran Rezvan

Masters Theses

"The shearing properties of an organic A̲ horizon of Bryce clay were studied and compared with the properties of the same soil treated with hydrogen peroxide. The treatment was to remove the organic matter and isolate it as a variable. Tests were performed on artificially sedimented samples of the untreated, 75 percent untreated, 50 percent untreated, 25 percent untreated, and the treated soil. The effective stress failure envelopes were found to be higher for the untreated soil than that of the treated. The elastic deformation, however, was larger for the untreated samples. The pore water pressure development due to shearing …

Effect Of Axial Mixing In Gas Absorption, Sundareswaran Parameswaran Iyer

Masters Theses

"The effect of axial mixing in the liquid phase on the performance of a gas absorption column was studied using the experimental data of Michael Brittan for the carbon dioxide and water system. In this study, piston flow conditions were assumed for the gas phase. A one-parameter mathematical model, which characterized the flow regimes in both the gas and the liquid phases undergoing plug flow conditions, was first curve fitted for its unknown parameter (i.e. the Number of Transfer Units) by a non-linear regression analysis procedure. The "AAPD" (i.e. the Average Absolute Percentage Deviation between the predicted value of the …

Shock Shields, Asbjorn Kvammen Jr.

Civil Engineering ETDs

A series of tests was conducted to obtain information concerning the effectiveness of a shock shield of reinforced concrete between ground surf ace and a buried structure as a means of reducing the shock transmitted to the structure due to airblast loading. Two shock shields were used. The diameter of both shields was 20 inches and the thicknesses were 6 inches and 2 feet. The structure was 20 inches in diameter with a thickness of 5 feet. Tests were performed in a 2- by 40-foot shock tube without shock shield and structure, with structure only, and with different thicknesses of …

Dynamic Response Of Circular Plates To Transient And Harmonic Transverse Loads Including The Effect Of Transverse Shear And Rotary Inertia, Perakatte Joseph George

Doctoral Dissertations

"Using an improved theory of plate vibration suggested by R. D. Mindlin which takes into account the effects of transverse shear and rotary inertia, free and forced transverse vibrations of uniform circular plates are studied and the results compared with those obtained using the classical theory of plate vibration. The governing equations are developed in polar coordinates using the equations of elasticity. Frequency equations for axisymmetric and antisymmetric vibrations are derived for solid circular plates under different boundary conditions and for an annular plate rigidly mounted on a shaft. The response of plates to different types of rapidly applied axisymmetric …

Analysis Of The Traveling-Wave Transistor, Vernon Ray Stanley

Doctoral Dissertations

"Transmission lines containing independent and dependent distributed sources are considered and the transfer matrices of various active distributed lines are derived. A method is discussed by which a lossy line can be made lossless by the appropriate choice of distributed sources. A steady-state analysis of the uniform traveling wave transistor is given. Considering the device as an active four port network, the transfer matrix is found in closed form and the power gain, output voltage, and input impedance are found. A computer program is written and the frequency response is given for various values of line parameters and terminations. Finally, …

Diffusion Of Iron And Cobalt In Nickel Single Crystals, Charles Frederick Heuer

Doctoral Dissertations

"Diffusion coefficients of iron-59 in nickel have been determined in the temperature range 815°C to 1200°C. The temperature dependence can be represented by an Arrhenius type relationship,...The effect of the isotopic mass on the diffusion coefficient of cobalt in nickel has also been investigated. The isotope effect parameter, E, was found to vary from .26 to .84 over the temperature range 970.5°C to 1200°C. Both results are consistent with the single vacancy mechanism of diffusion. No evidence of divacancy contributions to the mass transport has been found"--Abstract, Page i.