Digital Commons Network^™

Some Applications Of Automatic Control, N. H. Ceaglske

Journal of the Minnesota Academy of Science

No abstract provided.

Laboratory Model Shaking Table; An Investigation Of Defects And Suggested Improvements, George C. Horak

Bachelors Theses and Reports, 1928 - 1970

The laboratory model is considered in this thesis. Information gained from this investigation has not been trans­ferred to the larger industrial machines. Some of the factors noted concerning the efficiency of the laboratory shaking table are inherent in this small scale model only.

A Correlation Of Plate Efficiencies In Fractionating Columns., Earl K. Stigger 1920-2007

Electronic Theses and Dissertations

No abstract provided.

Experiments With Pressure Methods Of Air Content Determinations For Cement Concrete, L. E. Gregg

Kentucky Transportation Center Research Report

In our report entitled "A Summary of Experiments With Air Entrainment in Cement Concrete" released last September, we recommended among other things that "The gravimetric method (A.S.T.M. Designation: C138-44) be used only as a temperary expedient for determining air contents until the pressure method or some method not dependent upon physical properties of aggregates and not influenced by other variables can be firmly established" (see item 3, page 66 of that report). At that time we were thinking of the pressure apparatus demonstrated by representatives of the Portland Cement Association during construction of the Lexington-Nicholasville Road (Project F 524 (1)-1; …

Study Of The Effect Of Blended Coarse Aggregate On Air Entrained Concrete, S. T. Collier, L. E. Gregg

Kentucky Transportation Center Research Report

This research with combined coarse aggregates in cement concrete was initiated at the request of the Director of Design as a direct result of the condition study made by the Division of Design in 1945. In the report on this study it was shown that on the basis of averages pertaining to 80 projects with crushed limestone totalling about 395 miles in length, and 70 projects with Ohio River Gravel totalling approximately 410 miles in length, the service record for pavements with the river gravel was far inferior to that of pavements containing limestone coarse aggregate.

Specifically, the summary of …

Test 383: John Deere G, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF TEST REPORT: John Deere G

TEST A: The manufacturer's representative operates the tractor for a minimum of 12 hours using light to heavy drawbar loads in each gear.

This serves as a period for limber up, general observation and adjustments. Adjustments that are permissible include valve tappet clearance, breaker ,point gap, spark plug gaps, clutch and others of a similar nature. No new parts or accessories can be installed without having mention made of it in the report. No data' are recorded during this preliminary run except the time that the engine is operated.

BELT HORSEPOWER TESTS

TEST …

Operating Instructions For Cockshutt 30 Tractor, Tractor Museum

Tractor Maintenance, Repair, and Restoration

Index to General Operations

AIR CLEANER BATTERY BRAKES BELT PULLEY SHIFT CARBURETOR CARE AND OPERATION COOLING AND OVERHEATING CREEPER GEAR SHIFT CLUTCH CHASSIS DRAINING SYSTEM DISTRIBUTOR DRAW BAR PULL ENGINE SPECIFICATIONS SPARK PLUGS STEERING GEAR STORING AND HOUSING STARTING ENGINE AFTER STORAGE TRANSMISSION AND DIFFERENTIAL TIRES THERMOSTAT VALVE TAPPETS WEIGHTS REAR WHEELS INDEX ' T O ILLUSTRATIONS

Illustrations Anti-freeze chart Air cleaner Belt pulley Cross-section view Carburetor Distributor adjustment Distributor wiring Fan belt tension Generator Gear shift lever Instrument panel and controls

Lubrication chart Oil filter Rear wheel tread Steering gear 30 Safety Top view of transmission Valve adjustment Wiring …

Test 382: Cockshutt Model 30, Nebraska Tractor Test Lab

Nebraska Tractor Tests

All tractors tested at the Nebraska Tractor Test Laboratory were certified by their manufacturers as being stock model machines, conforming to specifications filed with the application for test. No special or high-test fuels were used except as recommended by the manufacturer as necessary.

All results within the official tractor test report were actually attained in tests and are without correction or allowances for friction, temperature, altitude, etc. The results were initially accomplished with the tractor in charge of skilled operators employed by the University.

Unless otherwise noted, each tractor was apparently in good condition at the end of the testing …

Test 390: Ellinwood Tiger Cat, Nebraska Tractor Test Lab

Nebraska Tractor Tests

All tractors tested at the Nebraska Tractor Test Laboratory were certified by their manufacturers as being stock model machines, conforming to specifications filed with the application for test. No special or high-test fuels were used except as recommended by the manufacturer as necessary.

All results within the official tractor test report were actually attained in tests and are without correction or allowances for friction, temperature, altitude, etc. The results were initially accomplished with the tractor in charge of skilled operators employed by the University.

Unless otherwise noted, each tractor was apparently in good condition at the end of the testing …

Test 389: Massey-Harris Model 44-Rt, Nebraska Tractor Test Lab

Nebraska Tractor Tests

All tractors tested at the Nebraska Tractor Test Laboratory were certified by their manufacturers as being stock model machines, conforming to specifications filed with the application for test. No special or high-test fuels were used except as recommended by the manufacturer as necessary.

All results within the official tractor test report were actually attained in tests and are without correction or allowances for friction, temperature, altitude, etc. The results were initially accomplished with the tractor in charge of skilled operators employed by the University.

Unless otherwise noted, each tractor was apparently in good condition at the end of the testing …

Test 386: Mccormick-Deering Farmall Cub, Nebraska Tractor Test Lab

Nebraska Tractor Tests

All tractors tested at the Nebraska Tractor Test Laboratory were certified by their manufacturers as being stock model machines, conforming to specifications filed with the application for test. No special or high-test fuels were used except as recommended by the manufacturer as necessary.

All results within the official tractor test report were actually attained in tests and are without correction or allowances for friction, temperature, altitude, etc. The results were initially accomplished with the tractor in charge of skilled operators employed by the University.

Unless otherwise noted, each tractor was apparently in good condition at the end of the testing …

Temperature Relationships In Tent Structures., Earl Robert Gerhard 1922-

Electronic Theses and Dissertations

No abstract provided.

Test 388 Oliver Row-Crop 88 Hc, Nebraska Tractor Test Lab

Nebraska Tractor Tests

No abstract provided.

Test 385: Ford Model 8n, Nebraska Tractor Test Lab

Nebraska Tractor Tests

All tractors tested at the Nebraska Tractor Test Laboratory were certified by their manufacturers as being stock model machines, conforming to specifications filed with the application for test. No special or high-test fuels were used except as recommended by the manufacturer as necessary.

All results within the official tractor test report were actually attained in tests and are without correction or allowances for friction, temperature, altitude, etc. The results were initially accomplished with the tractor in charge of skilled operators employed by the University.

Unless otherwise noted, each tractor was apparently in good condition at the end of the testing …

Test 380: John Deere B , Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF TEST REPORT: John Deere B

TEST A: The manufacturer's representative operates the tractor for a minimum of 12 hours using light to heavy drawbar loads in each gear.

This serves as a period for limber up, general observation and adjustments. Adjustments that are permissible include valve tappet clearance, breaker ,point gap, spark plug gaps, clutch and others of a similar nature. No new parts or accessories can be installed without having mention made of it in the report. No data' are recorded during this preliminary run except the time that the engine is operated.

BELT HORSEPOWER TESTS

TEST …

Test 381: John Deere B All-Fuel, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF TEST REPORT: John Deere B All-Fuel

TEST A: The manufacturer's representative operates the tractor for a minimum of 12 hours using light to heavy drawbar loads in each gear.

This serves as a period for limber up, general observation and adjustments. Adjustments that are permissible include valve tappet clearance, breaker ,point gap, spark plug gaps, clutch and others of a similar nature. No new parts or accessories can be installed without having mention made of it in the report. No data' are recorded during this preliminary run except the time that the engine is operated.

BELT HORSEPOWER TESTS …

Test 384: John Deere A, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF TEST REPORT: John Deere A

TEST A: The manufacturer's representative operates the tractor for a minimum of 12 hours using light to heavy drawbar loads in each gear.

This serves as a period for limber up, general observation and adjustments. Adjustments that are permissible include valve tappet clearance, breaker ,point gap, spark plug gaps, clutch and others of a similar nature. No new parts or accessories can be installed without having mention made of it in the report. No data' are recorded during this preliminary run except the time that the engine is operated.

BELT HORSEPOWER TESTS

TEST …

Test 387: John Deere M, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF TEST REPORT: John Deere M

TEST A: The manufacturer's representative operates the tractor for a minimum of 12 hours using light to heavy drawbar loads in each gear.

This serves as a period for limber up, general observation and adjustments. Adjustments that are permissible include valve tappet clearance, breaker ,point gap, spark plug gaps, clutch and others of a similar nature. No new parts or accessories can be installed without having mention made of it in the report. No data' are recorded during this preliminary run except the time that the engine is operated.

BELT HORSEPOWER TESTS

TEST …

Performance Study Of Mechanical Loading Machines In Coal Mining Practice, Kor Uyetake

Masters Theses

"In the transition from hand-loading methods in coal mining to mechanical loading methods various types of equipment have been developed to do the same job. Among the coal mining operators and among miners in the coal fields, various equipment preferences have developed. This produces a sharp difference of opinion. emotional statements of such ideas based upon personal likings do not contribute materially to coal mining progress - it merely serves to confuse the issue. The author feels that the opinions on the loading equipment should be based upon some factual data rather than the preconceived idea. Often it is difficult …

A Comparison Of The Use Of Polaroid And Colored Filters In The Multiplex Aeroprojector, Robert Greig Livingston

Masters Theses

"The purpose of this thesis is the drawing of a comparison between the use of the colored filters, which are normally employed in the multiplex aeroprojector by various mapping agencies throughout the country, and the use therein of Polaroid filters. The filters in the aeroprojector serve to break the projection of a stereoscopic pair of photographs into two impressions which are viewed separately by each eye of the observer, thus providing the main requirement for the observance of a three-dimensional effect. this stereoscopic effect is utilized in the multiplex plotting machine for the delineation of contours...In order to form a …

Some Preliminary Work On Metaphosphates In Ceramics, John Frederick Burst

Masters Theses

"For a good many years the accepted method of cementing ceramic joints was with a mixture of fire clay grog and a plastic clay binder. This did not prove too satisfactory for several reasons. Usually when enough plastic clay was added to give good workability the vitrification was lowered to such an extent that either excessive shrinkage or excessive bloating occurred, depending upon the extent to which the vitrification point was exceeded...In order to obtain a cement with high strength throughout a long firing range the manufacturers have turned to the addition of various organic binders and inorganic fluxes. Most …

The Effect Of Temperature On Mine Rocks, James Wilson Snider

Masters Theses

"The problem of this investigation involves the determination of the coefficients of thermal expansion of mine rocks, and the relationship of porosity, permeability, and consecutive temperature changes to the permanent elongation of those rocks. One of the major problems in mining today is that of the analysis of the action of exposed mine rock under changes of temperature. The immediate cause of a fall of ground in a mining excavation is due to the fact that some part of the mass that falls has been subjected to a stress beyond the strength of the rock. The question arises as to …

Effect Of Chromium, Molybdenum, Tungsten, And Vanadium Additions On The Physical Properties Of 1.4 Percent Titanium-Copper, Edward Palmer Patterson

Masters Theses

"Titanium, an element reported to be ninth most abundant of the elements in the earth's crust, has received very little experimental attention as an alloying element in non-ferrous metallurgy. In copper, titanium produces an age-hardening effect, which makes it of great value to copper manufacturers of fabricated products. Yet, but a handfull of men have investigated the copper-titanium equilibrium diagram, and the titanium rich portion of the diagram still remains a mystery. No work has been done on ternary alloys of copper-titanium to this date, as far as recorded information is concerned, and it is hoped that the present work …

Study Of The Method Of Geometric Mean Distances Used In Inductance Calculations, Harold Lockwood Seneff

Masters Theses

"The object of this thesis is to study the method of geometric mean distances as applied in the calculation of inductances of transmission line conductors and of multicircuit transmission lines. The thesis will consist of: (a) the derivation of some of the basic theorems and equations to be used, (b) the use of these theorems and equations in calculating the geometric mean distances of different transmission line conductors, and (c) practical application of geometric mean distances applied in the calculation of equivalent inductance of multicircuit transmission lines. The method of geometric mean distances as applied to individual conductors of single …

Ceramic Possibilities Of Some Missouri Clays And Shales, Leonard Nathanael Larson

Masters Theses

"Although many of the shales and clays of Missouri have in the past been, or are presently being used for the manufacture of heavy clay products such as face brick, common brick, sewer pipe, and tile, there is in these post-war years a significant shortage of these products within the state and country. Especially in the northwestern part of Missouri is there a distinct shortage, as only one structural clay plant is known to be operating in that area. The St. Louis and Southeastern Missouri districts are better prepared to meet construction demands, with several structural clay plants operating at …

Ethylcellulose Lacquer Coatings For Polystyrene Plastics., Stuart V. Heil

Electronic Theses and Dissertations

An ethylcellulose lacquer system for both decorative and protective purposes was developed for use on polystyrene plastics. It was found that a one-coat lacquer containing only alcohol solvents produced the most satisfactory finish. Formulations were based on experimental work, conducted to determine the effect of the various lacquer components on the plastic. The results of a study of formulations on a two-coat system are presented.

A Plastic Protective Film Coating For Metals., Arthur S. Widzer 1914-2002

Electronic Theses and Dissertations

No abstract provided.

Porous Backfill, Robert F. Baker

Kentucky Transportation Center Research Report

Until the late 1930's, the accepted practice for the construction of drainage installation included the use of a large, approximately No. 2 size, aggregate as porous backfill. However, a lage number of drains ceased to function as result of clogging or "silting"*, and many highway departments practically eliminated sub-surface and intercepting drainage.

The following report summarizes some of the more important studies that have dealt with "filter" (backfill material) to be used in drainage construction. The scope of it is limited, dealing primarily with the questions of proper gradation.

At present Kentucky Specifications (1) require that the gradations of the …

A Graphical Solution For Batch Steam Distillation Of A Binary Mixture., Howard D. Carlson 1921-

Electronic Theses and Dissertations

The theory for the graphical solution of batch steam distillation of a binary mixture is presented and illustrated. The results obtained from this graphical procedure are compared with actual experimental results. The comparison showed very close agreement between the graphical results and the experimental results. Three sets of experimental data are shown for benzene-bromobenzene mixtures and one complete set for benzene-toluene mixtures.

An Investigation Into The Adaption Of The Induction Furnace For Determining The Equilibrim Diagram Of The System Cu2s-Fes, John R. Cole

Bachelors Theses and Reports, 1928 - 1970

This investigation was started in an effort to find an accurate and efficient method of determining the freezing points of ferrous and cuprous sulphides, mixtures of the two substances, and from this to establish the liquidus line of the equilibrium dia­gram.