Digital Commons Network^™

A Case Study In The Development Of A Cost Reduction Methodology In The Public Sector, Ross Cooper Haines

Engineering Management & Systems Engineering Theses & Dissertations

Intense fiscal pressures have caused the Department of Defense (DoD) to explore new ways of reducing operating expenses. The primary technique used to achieve this objective is the use of competition - recently for maintenance requirements not previously subjected to competition. One such maintenance requirement is the periodic overhaul of one of the Navy's front line fighter aircraft - the F-14A Tomcat. This case study documents the cost reduction methodology developed by the DoD's incumbent overhaul facility in preparation for competition. The methodology discusses task time estimation, cost center structure, labor rate development and analysis, internal cost transfers as well …

Analysis And Development Of A Switched Capacitor Power Supply, John Richard Hackworth

Electrical & Computer Engineering Theses & Dissertations

The combination of a switched capacitor network and switching power supply techniques can result in a transformer less regulated DC power supply that is small, relatively simple, and efficient. In addition, the output of such a system could be operated over a wide range of common mode voltages. Multiple switched capacitor supplies could be stacked to achieve voltage multiplication.

Although the output of a system of this type is a continuous function, the internal operation must be analyzed in finite time elements. This numerical analysis will be shown in both a mathematical approach and a computer model.

Architecture For A Human-Robot Symbiotic System, Fred W. Depiero, Wayne W. Manges, Reid L. Kress, Mike R. Kedl, William R. Hamel

Electrical Engineering

This paper describes a human-robot symbiont that is under development at Oak Ridge National Laboratory. An overview of the symbiotic system is described that motivates the architecture that has been developed. The architecture is a hierarchical structure that consists of several expert systems which reside above a robot control interface. This interface allows the manipulator to be operated in both a teleoperated and autonomous mode. All these processes coexist with the lowest level of the hierarchy, which is a numerically intensive control algorithm. The architecture is implemented on five processors in a coarsely parallel system.

Irish Building Services News

Building Services Engineering

No abstract provided.

Heat And Momentum Transfer Analogies For The Transitional And Turbulent Flow Of A Non-Newtonian Power-Law Fluid In A Heated Pipe, Prapat Wangskarn, Bahman Ghorashi

Chemical & Biomedical Engineering Faculty Publications

A model is proposed for the transfer of heat to non-Newtonian power-law fluids flowing in heated horizontal pipes. Comparisons with the existing models, based on the absolute-percent-arithmetic-average-deviation and the percent-standard-deviation, show that under the transitional and turbulent flow regimes the proposed correlation fits the experimental data more accurately over a wide range of flow behavior index and there are no restrictions for its use when applied to pseudoplastic fluids.

Review And Analysis Of Pavement Management Practices In Kentucky, David L. Allen

Kentucky Transportation Center Research Report

Pavement Management is becoming increasingly more important in an era of limited budgets and aging pavement structures, State Highway Agencies (SHA) are attempting to manage the pavements under their jurisdiction more carefully and economically. All pavement management systems include all or some of the following items as inputs: (1) pavement distress, (2) serviceability or rideability, (3) inventory of the system, (4) structural adequacy, (5) traffic volumes and loadings, and (6) some form of performance history. This report documents Kentucky's present pavement management system. In addition, the duties and goals of the Pavement Management Branch are catalogged and described. Methods for …

Fault Tolerant Benes Networks, Manoj Bhatnagar

Theses

A fairly large number of fault tolerant topologies have been proposed for the multistage interconnection networks in the recent years. However very few of these schemes have focused on the Benes network. This thesis presents two new fault tolerant architectures for the Benes network. The thesis includes algorithms to construct these fault tolerant networks from a Benes network and the reconfiguration procedure in the event of a fault. The hardware characteristics of both the fault tolerant networks have been analyzed and compared.

Three-Dimensional Stress Analysis Of The Femoral Midshaft Utilizing Computed Tomography And Finite Element Analysis, Peter F. Marion

Theses

Recent advances in computer technology have provided both the medical community and biomedical engineers with a method for noninvasively evaluating the internal structure in a way not previously possible. A three-dimensional finite element model of a midshaft section of the femur was generated, utilizing Computed Tomography scan data. The CT scan data file was introduced into an edge-detection algorithm and a file of geometric edge data was generated. This edge data was introduced into a solid modeling Computer-Aided Engineering software package to produce a three-dimensional solid model. A mesh generation procedure was then used to create a three-dimensional finite element …

Development Of A Flexible Control And Automated Data Acquisition System For Wear Testing, Wen-Long Yao

Theses

The purpose of this work is to develop a flexible control and automated data acquisition system for wear testing procedure. A programmable logic controller (PLC) control philosophy and PC-based automated data acquisition system (DAS) were designed and organized for the wear testing machine in Surface Engineering Laboratory of Mechanical Engineering Department. The designed and performed separation of control and acquisition strategies saved a lot of engineering interface communication time. Several instrumentations and mechanism designs, such as selected RTD sensor, modified testing shoe for RTD installation, designed controlled lubrication mechanism, and designed load-unload mechanism, have been performed to fulfill the concerned …

Performance Analysis Of A Dynamic Reservation Multichannel Local Area Network, Abubakar A. Ibrahim

Theses

A reservation multiaccess protocol. is proposed to be used on multichannel local area networks. This protocol is advantageous for networks supporting integrated services. The delay and throughput performance for message transmission are obtained by analysist The delay performance of the protocol is similar to the M-CSMA/CD/IC multichannel network proposed by Marsan and Roffinella. It is found that the reservation protocol can provide better throughput-delay characteristics when the fraction of the total available bandwidth allocated to data is increased. It is also observed that the maximum throughput increases with the increase in the number of channels when the total bandwidth is …

Adaptive Fir Digital Filter Design And Simulation In The Noise Reduction System, Jack Jiabing Pang

Theses

The adaptive FIR digital filter is designed to suppress the noise in the tape recording and audio communication systems. The cutoff frequency of the digital FIR filters can be varied adaptively depending on the energy level of the input signal. In audio communication, especially, in tape recording systems, the noise obviously gets much bigger, when the frequency band of the system increases. The noise reduction system makes use of a phenomenon called masking, where the big signal-to-noise ratio makes human ears not sensitive to the noise. In a constant interval time, the system detects the signal level and compares the …

Computer Integrated Manufacturing : A Systems Approach For Small Manufacturing Enterprises, Sanjeet Jagdish Patel

Theses

This work is dedicated to small manufacturing enterprises seeking to explore Computer Integrated Manufacturing (CIM) technology, which is the recent trend in the manufacturing world. The main therie of this thesis is to improve productivity, product quality and reliability and reduce costs by integrating various disciplines.

Generic manufacturing functions including order entry, inventory control, manufcturing planning and control, automated drafting, direct numerical control etc. were enhanced by the effective utilization of low end workstations grouped together into a network and equipped worth industry standards software.

The introduction of computers into a manually resourced system yielded significant results such as reduction …

Ultrasonic Measurement Of The Geometric Parameters Of Gaseous Voids In Low Gravity Fluid Containers, A. T. Patten, William W. Durgin

Office of the Provost Scholarship

A demonstration system for the ultrasonic gauging of fluids in low-gravity has been designed and tested. For purposes of simplification, it was assumed that vapor within a liquid container in low-gravity would form a spherical bubble which would float freely in the container. The project was designed to show that ultrasonic techniques could be used to determine the geometry of the resulting sphere given a worst-case transducer arrangement. The motivation was to simplify transducer mounting requirements so that propellant or other storage vessels could be fitted with ultrasonic gauging systems with a single or perhaps a few transducer penetrations. Data …

Risk Objectivism And Risk Subjectivism: When Are Risks Real, Paul B. Thompson

RISK: Health, Safety & Environment (1990-2002)

Typically, those who discuss Risk management envision a two-step process wherein, first, Risk is more or less objectively appraised and, second, the acceptability of those Risks is subjectively evaluated. This paper questions the philosophical foundations of that approach.

Wright State University College Of Engineering And Computer Science Bits And Pcs Newsletter, January 1990, College Of Engineering And Computer Science, Wright State University

BITs and PCs Newsletter

A fourteen page newsletter created by the Wright State University College of Engineering and Computer Science that addresses the current affairs of the college.

Santa Clara Magazine, Volume 32 Number 2, Winter 1990, Santa Clara University

Santa Clara Magazine

12 - WHO TAKES CARE OF THE KIDS Day care is one of the major issues society will be forced to grapple with in the 1990s. By Susan Frey

17 - THE GENERAL PAYS A VISIT The superior general of the Jesuit order makes a rare visit to Santa Clara and addresses the SCU and Bellarmine communities. By Peter-Hans Kolvenbach, S.J.

22 - PASSPORT TO FRIENDSHIP A Nome, Alaska Cub Scout troop makes the ultimate field trip, an exchange visit with the Young Pioneers in Provideniya, Russia. By Claire Murphy

26 - WHO, ME? Hazelden is considered the nation's premier …

Physiological Diversity And Distributions Of Heterotrophic Bacteria In Deep Cretaceous Sediments Of The Atlantic Coastal Plain, James K. Fredrickson, David L. Balkwill, John M. Zachara, Shu-Mei W. Li, Fred J. Brockman, Mary Simmons

United States Department of Energy: Publications

A series of 23 intact core segments was obtained from two distinct deep subsurface geological formations, the Middendorf and the Cape Fear formations, underlying the southeastern coastal plain of South Carolina. The Middendorf formation in this region consists of permeable, saturated, sandy sediments; the Cape Fear formation consists mainly of less permeable sediments. The core segments were separated by vertical distances ranging from several centimeters to 48 m. Aerobic chemoheterotrophic bacteria were enumerated on a dilute medium, and populations ranged from 3.1 to 6.4 log CFU g of sediment^-1 in the Middendorf cores and from below detection to 4.3 …

Influence Of Mineral-Bound Humic Substances On The Sorption Of Hydrophobic Organic Compounds, Ellyn M. Murphy, John M. Zachara, Steven C. Smith

United States Department of Energy: Publications

The sorption of three hydrophobic organic compounds (HOC) was investigated on hematite and kaolinite that had been coated with natural humic substances over a mass percent carbon range of 0.01-0.5%. Increasing quantities of sorbed humic substances increased the sorption of HOC. Anthracene, the most hydrophobic HOC, showed the greatest sorption enhancement, while the most aromatic coating, peat humic acid, was the strongest sorbent. Depending on the type of humic acid coating and the mineral substrate, the experimental K_oc values were either higher or lower than those predicted by the K_ow The sorptivity of a given humic acid for …

Stress-Induced Infrared Frequency Shifts In Polyethylene, G. A. Pfeffer, D. W. Noid

United States Department of Energy: Publications

The molecular dynamics technique is used to study the spectral response of a polyethylene chain in a crystal environment under a mechanical deformation. The MUSIC method, which was previously shown to accurately compute dispersion curves from the time-dependent structure factor, is used. A complete characterization of frequency shifts is presented for various lamellar thickness, temperatures, stress (or pressure), and mass defects.

Major Project Management: The Yale Telecommunications Project

ACUTA: Other Publications

Back in the good old days, when the telephone business was simpler and Saturday night television was worth watching, I can remember Ted Knight the newsman (remember him on The Mary Tyler Moore Show?) looking off into some imagined horizon in the newsroom when asked how he happened to come to his current position. With head cocked upward and his hand clutching his right lapel, he'd start in his deepest, most pompous voice: “lt all started in a small, 5,000-watt radio station..." Around here it a!! started with a 12,000-line, decade-old Centrex system and a new hospital building going up …

Mining In Maine : Past, Present, And Future, Carolyn A. Lepage

Maine Collection

Mining in Maine : Past, Present, and Future

by Carolyn A. Lepage, Michael E. Foley, and Woodrow B. Thompson

Maine Geological Survey, Department of Conservation, Augusta, Me., 1990.

Contents: Introduction / The Early Years: Pre-Civil War / The Civil War to World War II / The War Years of the 1940's / The Postwar Years: 1940's to 1960 / The 1960's / The 1970's / Maine Mineral Resources Association / The 1980's / Current Mining and Exploration / Future Potential / Acknowledgments / References

Impulse, Kara Donohoe

Impulse (Jerome J. Lohr College of Engineering Publication)

Features:
[Page 2] Astrophysicist's research seeks to correct "earth colors"
[Page 3] Classroom building vacated
[Page 4] Engineering students "cap" their education through practical experience
[Page 6] Scientists from Egypt, West Africa learn mapping by satellite
[Page 7] Tillage research seeks to reduce compaction
[Page 8] Lap-Top computer controls fertilizer rates
[Page 9] Engineering sculpture dedicated
[Page 10] Research seeks to improve structural design of post-frame buildings
[Page 11] Buckley dies of cancer a t 65
[Page 12] Sencore donates "state of the art" test equipment
[Page 13] Boisjoly headlines ethics seminar; 600 attend
[Page 14] Mechanical engineer stays in …

The Development Of The Smelting Industry In The Central Salt Lake Valley Communities Of Midvale, Murray, And Sandy Prior To 1900, Charles E. Hughes

Theses and Dissertations

This thesis found that the three communities of Midvale, Murray, and Sandy were the center of the smelting industry in the Salt Lake Valley. These communities became the center of smelting because of their central location, the readily available water supply, and the availability of an inexpensive, efficient transportation system to ship the bullion. The smelters were surrounded by two major mountain ranges which provided a ready supply of good lead, silver, and copper ore.

The development of the smelting industry followed three separate phases or periods. The first phase was one of experimentation or period of discovery, in which …

Enhancing An Engineering Learning Environment, Paul J. Palazolo, Patricia Brackin

Journal of the Arkansas Academy of Science

No abstract provided.

Spatial Control Of Crop Inputs Via Laptop And Typical Field Travel, Joseph Alan Schumacher

Electronic Theses and Dissertations

Field Grid Sense (FGS) is a system developed for use with a laptop computer to control crop production inputs. FGS can be used for spatially controlling and recording field inputs according to regional requirements within the field. Location is identified via the travel lanes formed during field operations. Grid areas within lanes are formed by measuring from the beginning of each lane to the start of each grid within the lane. Distance measurements are reset at the beginning of each lane in order to eliminate accumulated distance error in the field. A fifth wheel, which runs in the smooth path …

Doctor Of Arts In Information Science, Nova University

College of Engineering and Computing Course Catalogs

No abstract provided.

Master Of Science In Computer Science, Nova Southeastern University

College of Engineering and Computing Course Catalogs

No abstract provided.

Computer Education Complete Masters Program, Nova Southeastern University

College of Engineering and Computing Course Catalogs

No abstract provided.

Bachelors In Computer Science Course Descriptions, Nova Southeastern University

College of Engineering and Computing Course Catalogs

No abstract provided.

Center For Computer And Information Sciences Application Package 1990, Nova Southeastern University

College of Engineering and Computing Course Catalogs

No abstract provided.