Digital Commons Network^™

Ammonia Synthesis By Nanosecond Pulsed Atmospheric Pressure Plasma Jets Impinging On Water, Zach Caudell, Lynnet Rich, Olga Pakhomova, Chunqi Jiang

Bioelectrics Publications

Developing energy-efficient technologies for carbon-neutral ammonia (NH₃) synthesis is critical for decentralized fertilizer production and global decarbonization. This study investigates generating NH₃ from water using a nanosecond pulsed atmospheric pressure plasma jet (ns‑APPJ) operating in either N₂ or dry air. The plasma jet reactor employed approximately 250 ns, up-to-22 kV pulses at 500 Hz to sustain a nonequilibrium discharge impinging directly on static liquid water. The kinetics, energy efficiency, and product selectivity of NH3 formation were quantified as functions of the pulse voltage, repetition frequency (PRF), and gas flow rate. NH₃ production increased linearly with treatment time and scaled strongly …

Design, Optimization, And Techno-Economic Analysis Of A Standalone Pv-Wind-Battery Microgrid For A Remote Load In Kurdistan Region Of Iraq, Harwan Mohammed Taha, Laith Akram Mohammed

Mansoura Engineering Journal

Standalone microgrids play a crucial role in rural areas where grid electricity delivery is difficult and expensive. This research verifies the effectiveness of a standalone microgrid in a rugged area, Pers Mountain in Akre district, Duhok governorate, Iraqi Kurdistan. A first hybrid renewable energy system (HRES)-based standalone microgrid is presented to supply a remote load. Solar and wind energy are employed for their reliability, sustainability, and abundance, with battery storage ensuring continuous power when solar and wind are unavailable. Simulation results demonstrate reliable power supply during summer months (loss of power supply probability < 5%), with the system operating across three modes — PV-dominant daytime, combined wind-battery evening, and battery-discharge nighttime. The inverter achieved minimum total harmonic distortion of 1.53% for both current and voltage outputs, below the IEEE 519 limit. A full-year hourly particle swarm optimization (PSO) sizing analysis assessed annual reliability and each source's economic contribution: the original fixed sizing yields an annual loss of power supply probability (LPSP) of 26.80% (expected energy not served ~1,471 kWh/year), motivating a PSO-optimized PV-battery configuration achieving annual LPSP of 5% (~274 kWh/year unserved) at comparable cost. The site's wind resource is reasonable (13.8% capacity factor), but the fixed tower and controller cost outweighs its contribution at this small scale. The proposed HRES totals $11,960–$16,317 depending on configuration, approximately 28–38 times lower than grid extension ($455,600) to the site, while producing zero CO₂ emissions and avoiding approximately 4,189 kg/year versus an equivalent HOMER Pro-simulated diesel generator.

C2p-M: Critical Connection Protection In Multiplex Graphs, Conggai Li, Wei Ni, Ming Ding, Youyang Qu, Jianjun Chen, Wenjie Zhang, Thierry Rakotoarivelo

Research outputs 2022 to 2026

Multiplex graphs represent diverse real-world interactions among entities, where multiple relationship types coexist within the same set of entities. These graphs introduce privacy risks, as data collectors can exploit cross-layer dependencies to infer hidden and sensitive connections. In this work, we propose a C2P-M framework that identifies and protects critical connections while preserving the structural information in multiplex graphs. Unlike conventional methods for single-layer graphs that perturb all edges uniformly, C2P-M selectively protects critical connections, maintaining the analytical usability of the graph. To achieve this, we introduce the multiplex p-cohesion model, which incorporates new score functions that account for both …

Guitar Amplifier Directivity, Rachel C. Edelman, Brian E. Anderson, Samuel D. Bellows, Timothy W. Leishman

Directivity

No abstract provided.

Ev Charging And V2g Operation For Distribution System Vpp Including Model Predictive Control, Rosemary E. Alden, Simone Silvestri, Malcolm D. Mcculloch, Dan M. Ionel

Electrical and Computer Engineering Faculty Publications

Future smart grid virtual power plants (VPPs) are considered for development based on industry communication standards for electric vehicle (EV) chargers such as Open Charge Point Protocol (OCPP), IEC 15118, and IEC 61851. To support research and development of computationally intelligent controls for distributed EV batteries, a python-based API OpenDSS VPP framework is utilized with thousands of experimental smart meter profiles, the IEEE 123 node test feeder, and hundreds of national survey-based EV modules for conventional and optimal charging and vehicle-to-grid (V2G) control development to mitigate any voltage violations and reduce peak load. A methodology is proposed for model-predictive control …

Pillpetz: A Smarter Way To Encourage Medication Adherence In Children, John H. Begley

CMC Senior Theses

Medication adherence is usually framed as a problem of patient behavior, but this thesis argues that it is equally a problem of design. Children who take daily medication face barriers that adults often do not: developing executive function, dependence on caregivers, shifting school and home routines, privacy concerns, and stigma around being perceived as different. The standard prescription bottle, by contrast, was designed primarily for dispensing efficiency, safety, and accidental ingestion prevention—not for sustained daily use by a developing child.

This thesis proposes PillPetz, a smart pill case and digital companion that uses routine, play, dose confirmation, and caregiver-connected support …

Robust Broadband Characterization Of Flexible Absorbers, Sheet Material, And Liquids Using A Coaxial Structure, Joseph Christopher Stecher

Masters Theses

Modern high-frequency measurement systems require reliable calibration and sample positioning to ensure measurement fidelity. This thesis presents three studies addressing practical limitations in broadband material parameter extraction and instrumentation.

The first study introduces a modified Nicolson–Ross–Weir (NRW) technique for flexible, compression-sensitive materials from 100 MHz to 18 GHz. Rigid 3D-printed spacers ensure precise sample positioning, and a T-matrix–based de-embedding procedure removes spacer effects. Validation using microstrip measurements and full-wave simulation confirms accurate permittivity extraction across compression levels.

The second study extends NRW to sheet materials enabling accurate material characterization. Independent validation using toroidal inductors with leakage correction and parallel-plate capacitors …

Incremental Cluster Validity Indices And Their Role In Interpreting Lifelong Learning Systems, Niklas Max Melton

Doctoral Dissertations

Clustering and supervised learning are often treated as distinct paradigms, yet both rely on structure in feature space. This dissertation investigates the relationship between cluster validity indices (CVIs) and supervised learning in real-time and lifelong learning settings where data arrive incrementally and cannot be revisited. Across four studies, it develops methods for online cluster validation, uses supervised learning to improve their interpretability, and applies these ideas to evaluating performance degradation in continual learning.

The first study extends incremental cluster validity indices (iCVIs), enabling widely used validation metrics to operate in streaming environments. Experiments on synthetic and real-world datasets show systematic …

Validating A Low-Cost Radio Frequency Characterization Framework For Development-Grade Software-Defined Radios In Short-Duration Cubesat Missions, Thomas Wayne Francois

Masters Theses

Software-defined radios (SDRs) and CubeSat platforms have reduced the cost and complexity of space-based communication systems, enabling broader participation in satellite missions. While low-cost radio hardware is increasingly accessible, the ability to characterize and validate its performance remains constrained by the high cost and limited access to traditional RF test equipment. This disparity creates a challenge for small satellite development teams, which must characterize communication-system technical performance with limited access to laboratory-grade instrumentation.

This thesis presents a low-cost RF characterization framework for assessing key radio-frequency performance metrics using readily available hardware and measurement techniques. The approach integrates frequency translation, SDR-based …

Machine Learning Based Automation Of Pcb Pdn Design And Optimization, Haran Manoharan

Doctoral Dissertations

The rapid increase in power density and stringent power-integrity requirements in modern System-on-Chip (SoC) platforms have made Power Delivery Network (PDN) design an increasingly complex, multi-stage challenge. Critical decisions must be made both during pre-layout planning, such as stackup configuration, power-plane geometry, and early decoupling capacitor (decap) budgeting, and during post-layout refinements. Traditional heuristic and evolutionary optimization techniques struggle with scalability, require extensive manual iteration, leading to long runtimes and limited adaptability across varying board configurations. To address these challenges, this work proposes a unified reinforcement-learning-driven framework for automated PDN synthesis and decap optimization that spans both pre-layout and post-layout …

Electron Beam Irradiation Effects On Bulk Metals: A Comparative Study Of Polycrystalline Versus Single-Crystalline Structures, A. A. Elmustafa, N. A. Sultana, A. H. Al-Allaq, M. Ojha, Y. S. Mohammed, J. Vennekate, H. Baumgart

Mechanical & Aerospace Engineering Faculty Publications

This study investigates the effects of electron beam (e-beam) irradiation on the mechanical and structural properties of eight bulk metallic samples, comprising both polycrystalline (PC) and single-crystalline (SC) forms of Ni, Cr, V, and Ti. These metals were evaluated as potential candidates for beam exit windows in high-power (MW-class) particle accelerators. The primary objective is to identify metals capable of withstanding the conditions of high-power/MW-class e-beam accelerators and serve effectively as exit windows. Selection criteria were based on each metal’s intrinsic properties, power dissipation capability, and irradiation-induced changes in mechanical behavior, including hardness, elastic modulus, and defect density. Comprehensive characterization …

Array Signal Processing And Machine Learning In 5g/6g Networks, Roopesh Kumar Polaganga

Electrical Engineering Dissertations - Archive

This dissertation investigates advanced methodologies in Array Signal Processing (ASP) and Machine Learning (ML) to enhance the performance, efficiency, and intelligence of next-generation wireless networks, with a primary focus on 5G and emerging 6G systems. As wireless networks face rapid traffic growth, increasingly heterogeneous service requirements, and more complex propagation environments, conventional design and optimization approaches become insufficient to meet evolving demands in reliability, capacity, spectral efficiency, and energy efficiency. On the network intelligence side, this work develops data-driven frameworks for causal discovery, scheduler enhancement, session-duration prediction, and Radio Resource Control (RRC) state optimization using real-world telecommunication network data. On …

Enhancing Deep Reinforcement Learning With Expert Demonstrations For Mobile Robot Navigation In Unstructured Off-Road Environments, Dulitha Dabare

Theses: Doctorates and Masters

Advancements in the field of Deep Learning has ushered in a boom in autonomous navigation research. Most of the work being conducted in this space, however, has focused on on-road urban navigation scenarios, with unstructured outdoor terrain navigation receiving much more limited attention. Given the wide range of applications that exist for legged and wheeled ground robots in off-road environments in areas such as agriculture, mining and disaster recovery, there is a growing need for research work to improve the navigational capabilities of mobile robots deployed in these challenging environments.

A promising candidate for application to these navigation challenges in …

Multimodal Scene Understanding For Mobile Robot Navigation In Unstructured Outdoor Environments, Liyana Mudiyanselage Nipuna Dinendra Wijayathunga

Theses: Doctorates and Masters

The application of autonomous field robots in agriculture, mining, transport and logistics, disaster management, and exploration has increased with advances in sensing, perception, and autonomous navigation technologies. Western Australian off-road environments present challenges for autonomous ground robots because they contain unstructured ter rain, variations in appearance and geometry, changing illumination, and visually similar regions with different traversal characteristics. Reliable operation therefore requires scene understanding methods capable of representing the environment according to its navigability for robot traversal.

This PhD research investigates multimodal scene understanding for autonomous ground robot navigation in unstructured off-road environments. The research focuses on the development of …

Large Language Models For Neurology: A Mini Review, Donald C. Wunsch, Daniel B. Hier

Electrical and Computer Engineering Faculty Research & Creative Works

Large language models have the potential to transform neurology by augmenting diagnostic reasoning, streamlining documentation, and improving workflow efficiency. This Mini Review surveys emerging applications of large language models in Alzheimer's disease, Parkinson's disease, multiple sclerosis, and epilepsy, with emphasis on ambient documentation, multimodal data integration, and clinical decision support. Key barriers to adoption include bias, privacy, reliability, and regulatory alignment. Looking ahead, neurology-focused language models may develop greater fluency in biomedical ontologies and FHIR standards, improving data interoperability and supporting more seamless collaboration between clinicians and AI systems. Two future developments have the potential to be particularly impactful: (1) …

Mitigating Hysteresis In Metal-Coated Fibers Via Optimized Thermal Treatment For Advanced Distributed High-Temperature Sensing Applications, Koustav Dey, Rony Kumer Saha, Bohong Zhang, S. Narasimman, Farhan Mumtaz, Jeffrey D. Smith, Rex E. Gerald, Ronald J. O'Malley, Jie Huang

Electrical and Computer Engineering Faculty Research & Creative Works

Metal-coated optical fibers are widely employed in sensing applications owing to their superior mechanical strength and corrosion resistance. However, their calibration at elevated temperatures is hindered by hysteresis, manifested as discrepancies between heating and cooling cycles, primarily caused by residual strain from mismatched thermal expansion coefficients (TECs) between the metal coating and silica cladding. This research introduces an optimal heat treatment procedure aimed at minimizing the impact of the mismatch in TECs between the cladding and the coating materials that causes the residual strain in gold (Au) and copper (Cu) coated fibers for achieving reliable distributed high temperature sensing up …

Multi-Parameter Optimization And Adaptive Temperature Compensation For Fbg Strain Sensors In Wide-Temperature-Range Aerospace Applications, Ruling Zhou, Jiacheng Yu, Yutang Dai, Jianguan Tang, Minghong Yang, Farhan Mumtaz

Electrical and Computer Engineering Faculty Research & Creative Works

Accurate strain measurement in cryogenic fuel pipelines is crucial for ensuring the structural integrity and reliability of rocket engine systems operating under extreme thermal conditions. Fiber Bragg grating (FBG) sensors show significant potential for such applications; however, their inherent temperature-strain cross-sensitivity limits performance over wide temperature ranges. This research presents an enhanced compensation strategy combining multi-parameter optimization with temperature-zone-specific adaptation to improve the accuracy and stability of FBG-based strain sensing in harsh aerospace environments. Four special steel substrate materials including S03, S06, S07, and 1Cr18Ni9Ti, were evaluated using strain transfer theory and thermo-mechanical coupling simulations. Genetic algorithms optimized key design …

Safe Optimal Control Framework For Cooperative Manipulation Of Objects In Human–Robot Teams, Irfan Ganie, Sarangapani Jagannathan

Electrical and Computer Engineering Faculty Research & Creative Works

This article introduces a distributed deep neural network (NN)-based adaptive control framework for cooperative object manipulation in human–robot teams with unknown agent dynamics by using three distinct multilayer NN observers (MNNOs). The first observer, termed the reference point estimator, enables each robotic agent to estimate the object's reference center using consensus-based learning, even without direct access to global reference trajectories. The second observer, referred to as the human force-to-trajectory estimator, uses human-applied forces to infer the intended position, velocity, and acceleration of the object, enabling real-time estimation of human intent. Together, these two observers allow distributed estimation of human-intended motion. …

High-Resolution, Fast-Response Optical Fiber Temperature Sensor With A Large Measurement Range Based On Fiber-Tip Alumina Fabry-Pérot Interferometer, Ruimin Jie, Chen Zhu, Robert Abbott, Michael Davis, Xiong Zhang, Jie Huang

Electrical and Computer Engineering Faculty Research & Creative Works

We present an alumina-tip optical fiber Fabry-Pérot interferometric temperature sensor exhibiting high-temperature performance, rapid response, and high resolution. Fabricated by fusion splicing an alumina micro disk directly to a single-mode fiber, the sensor achieves robust, stable operation without complex fabrication processes or adhesives. Experimental evaluation confirms a measurement range extending to 1000°C, with sensitivity of 28.66 pm/°C, a resolution of 0.042°C, and a rapid response time of approximately 13 ms. Compared to state-of-the-art optical fiber FPI sensors, our alumina-tip sensor offers superior overall performance, effectively addressing critical demands for high-resolution, fast-response temperature measurement in extreme environments including aerospace, structural monitoring, …

Waveguide-Assisted Single-Mode Fiber Bragg Gratings In A Highly Multimode Coreless Fiber Via Femtosecond Laser Inscription For Extreme Temperature Quasi-Distributed Thermal Sensing, Farhan Mumtaz, Koustav Dey, Bohong Zhang, Jeffrey D. Smith, Ronald J. O'Malley, Jie Huang

Electrical and Computer Engineering Faculty Research & Creative Works

This research reports a potential quasi-distributed thermal mapping optical sensing system for extreme temperatures, leveraging femtosecond (fs) laser inscribed single-mode fiber Bragg gratings (FBGs) and a waveguide within coreless, highly multimode optical fiber, resulting in a single-mode structure. Unlike doped single-mode fibers, coreless fibers composed of silica rods prevent issues associated with dopant migration and ensure data accuracy. The strategic placement of point-by-point FBGs in a cascaded formation on the fs-laser inscribed waveguide facilitates localized multipoint sensing. The long-term stability of the proposed waveguide-assisted FBG system was assessed over 24 hours at elevated temperatures (1000°C), showing no hysteresis during heating …

Performance Analysis And Optimization Of Fructose Memristor-Based Neuromorphic Systems, Harshvardhan Uppaluru, Shakil Mahmud Jiban, Shah Zayed Riam, Feng Zhao, Jinhui Wang

Electrical and Computer Engineering Faculty Research & Creative Works

Natural organic memristors have demonstrated promising synaptic behavior, positioning them as strong candidates for synaptic devices in neuromorphic systems. This paper presents the fabrication and evaluation of a neuromorphic system based on natural organic 16-level and 32-level fructose memristors. First, the manufacturing process of fructose memristors is described in detail. Second, the nonlinear property associated with fructose memristors is investigated, and an optimization method is applied to address the nonlinear effects. The performance of the fructose memristor-based neuromorphic system on MNIST with a multi-layer perceptron and on CIFAR-10 with VGG-8 is evaluated and reported under various conditions -with/without nonlinearity optimization …

Integrating Optical And Radiofrequency Interferometry For Enhanced Phase Sensing, Ruimin Jie, Zhaopeng Zhang, Chen Zhu, Jie Huang

Electrical and Computer Engineering Faculty Research & Creative Works

Interferometry is a crucial investigative technique used across diverse fields to achieve high-precision measurements. It works by analyzing the phase difference between two interfering waves, which results from variations in optical path lengths within an interferometer. We introduce a novel method for directly measuring changes in the phase difference within an optical interferometer, importantly, with the added advantage of a controllable enhancement factor. This approach is achieved through a two-step process: first, the optical phase difference is encoded into a sub-GHz radiofrequency (RF) signal using microwave-photonic manipulation; then, RF interferometry-assisted phase amplification is implemented at the destructive interference point. In …

Online Lifelong Optimal Adaptive Control Of Partially Uncertain Strict Feedback Discrete-Time Systems With Application To Quadrotor Uavs, Maxwell Geiger, Sarangapani Jagannathan

Electrical and Computer Engineering Faculty Research & Creative Works

This article considers the infinite time horizon optimal adaptive tracking control of partially uncertain strict feedback discrete-time (DT) systems with application to quadrotor uncrewed aerial vehicles (UAVs). First, the strict feedback DT system is transformed into an equivalent affine nonlinear DT system in terms of the tracking error dynamics. The optimal adaptive tracking control problem is solved using an augmented system approach, where a horizon of future bounded reference trajectory points is used in the augmented state, when compared to using a single point. It is assumed that the internal dynamics of the strict feedback system are unknown, but the …

Enhancing Measurement Accuracy: The Impact Of Missing Data On Parameter Estimation In Mass-Spring-Damper Systems, Michkath Omanda Bouraima, Steven Thompson, Maciej J. Zawodniok

Electrical and Computer Engineering Faculty Research & Creative Works

In sensor-driven dynamic systems, missing data can severely degrade parameter estimation accuracy. This article investigates the impact of missing data on phase estimation in a mass-spring-damper system using an information-theoretic framework based on the Cramér-Rao Lower Bound (CRLB). Closed-form CRLB expressions are derived for four scenarios: complete data, missing completely at random (MCAR) deletion, MCAR-based imputation, and missing at random (MAR) missingness via a selection-weighted formulation. These bounds are used as theoretical benchmarks to evaluate classical imputation methods (last observation carried forward (LOCF), linear interpolation) and advanced approaches (Kalman filtering, Rauch-Tung-Striebel (RTS) smoothing, Bayesian inference, and transformer-based imputation) through Monte …

Rf-Attennet: A Hybrid Attention-Enhanced Network For Mixed Signal Classification In Uav Swarm Detection, Prajoy Podder, Mohammad Atikur Rahman, Maciej Zawodniok, Sanjay Madria

Electrical and Computer Engineering Faculty Research & Creative Works

The continuous increase of UAVs, particularly in swarms, creates significant challenges for security and airspace regulation. Traditional RF fingerprinting methods struggle to detect and classify UAV swarms due to overlapping signals and interference. This study introduces RF-AttenNet, a hybrid deep learning model designed to classify mixed UAV signals by analyzing composite RF spectrograms. RF-AttenNet uses dual attention mechanisms, channel and spatial attention to focus on critical spectral features, enabling the model to effectively separate and identify overlapping UAV signals. We have developed custom composite UAV datasets that simulate real-world swarm interference, incorporating both single and mixed UAV classes. RF-AttenNet achieves …

Fixed-Time Consensus Tracking For Nonlinear Multi-Agent Systems Under Aperiodically Intermittent Control, Lei Xue, Tong Wu, Wenwen Jia, Donald C. Wunsch

Electrical and Computer Engineering Faculty Research & Creative Works

This article explores the problem of fixed-time consensus tracking (FT-CT) for nonlinear multi-agent systems utilizing the a periodically intermittent control (AIC) strategy. In contrast to existing control algorithms, the proposed algorithm utilizes the AIC strategy instead of the conventional continuous-time control strategy, effectively reducing the consumption of communication resources. Moreover, the problem of intermittent FT-CT is well handled by proposing the average control rate of the AIC strategy. Two theorems based on the cases of directed and undirected graphs are proposed, respectively. Finally, the validity of these results is confirmed through numerical simulations on a general nonlinear system and a …

Resolving Stiffness Trade-Offs In Simultaneous Pressure And Vibration Sensing Using A Corrugated-Tube Fiber-Optic Sensor, Yizheng Chen, Yan Tang, Jie Huang, Qi Zhang, Biyao Shi, Zewei Wu

Electrical and Computer Engineering Faculty Research & Creative Works

This article proposes and experimentally demonstrates a corrugated-tube-based fiber-optic sensor capable of measuring pressure, vibration, or both simultaneously. To address the limited sensitivity of conventional diaphragm-based designs, the sensor incorporates an optimized corrugated tube that balances the conflicting stiffness requirements for pressure and vibration measurements. The corrugated tube, acting as a mechanical transducer, is integrated with an extrinsic fiber-optic Fabry–Perot interferometer (EFPI). The EFPI cavity is formed between a reflective surface at the sealed end of the corrugated tube and the cleaved end face of an optical fiber fixed within a mounting assembly. In this configuration, displacement of the corrugated …

Nash Equilibrium Strategies For Multicluster Pursuit–Evasion Game With Disturbances: A Prescribed-Time Convergence Approach, Lei Xue, Xian Yu, Yongbao Wu, Jian Liu, Changyin Sun, D. C. Wunsch

Electrical and Computer Engineering Faculty Research & Creative Works

This article investigates the problem of prescribed-time Nash equilibrium (NE) seeking for a multicluster pursuit–evasion game (PEG) subject to external disturbances. To mitigate the impact of disturbances and reach the NE within a user-defined prescribed time, a prescribed-time disturbance observer (PTDO) is devised to estimate and compensate for them. Based on this observation, a novel control algorithm is developed, which facilitates collaboration among multiple pursuers to capture multiple evaders within the prescribed time. It is theoretically demonstrated that the designed algorithm ensures prescribed-time convergence to the NE of the multicluster PEG with disturbances. Finally, numerical simulations are conducted to verify …

Real-Time Multiregional Market-To-Market Congestion Management Through Exchange Of Relief Cost Curve, Haotian Chen, Yonghong Chen, Jose Daniel Lara, Jarrad Wright, Matthew Bossart, Sebastian De Jesus Machado, Rui Bo

Electrical and Computer Engineering Faculty Research & Creative Works

This paper introduces a novel method for multiregional market-to-market (M2M) coordinated congestion management. It identifies shortcomings in existing M2M approaches, where Regional Transmission Organizations (RTOs) exchange shadow prices and relief requests to optimize congestion relief allocations across interconnected regions. Two methods are proposed to enhance flow and price convergence. The first method proposes that both Regional Transmission Organizations (RTOs) use state-estimator flows directly to determine relief requirements, eliminating delays and potential oscillations caused by using market flows calculated from the prior period under existing M2M approach. The second method involves exchanging transmission relief cost curves, enabling each RTOs to integrate …

Transformer-Customer Relationship Identification Based On Load-Switching Fluctuation Characteristics Considering Same-Feeder-Adjacent-Transformer Condition, Yanan Zhang, Gan Zhou, Yuyuan Liu, Wei Gu, Yanjun Feng, Yujue Wang, Rui Bo

Electrical and Computer Engineering Faculty Research & Creative Works

Accurately identifying the connectivity between transformers and downstream three-phase customers in low-voltage distribution networks is challenging, because voltage curves of different phases and nearby nodes can be weakly distinguishable, especially when adjacent transformers on the same feeder serve geographically close customers with highly similar voltage curves. This paper proposes a novel method based on load-switching fluctuation characteristics recorded by smart meters. By extracting localized current and voltage fluctuations and establishing correlation matching, the method overcomes the limited discriminability using steady-state measurements. The method operates in two stages: first, switching-induced fluctuation characteristics are extracted and matched to cluster customers by the …