Digital Commons Network^™

Characterization Of Two-Dimensional Finite-Aperture Wire Grid Polarizers By A Spectral-Domain Technique, Michael A. Jensen, Gregory P. Nordin

Faculty Publications

We investigate the transmission characteristics of perfectly conducting two-dimensional wire grid polarizers fabricated in finite and infinite apertures using a rigorous spectral-domain mode-matching method. Specifically, the transmission coefficient for both transverse-electric and transverse-magnetic polarizations, extinction ratio, and diffraction pattern are characterized for a wide variety of geometric and material parameters including aperture dimension, conducting wire fill factor, wire spacing, polarizer thickness, material dielectric constants, and incident wave arrival angle. The results indicate that the transmission behavior is largely insensitive to aperture dimension.

Using Neural Networks To Estimate Wind Turbine Power Generation, Shuhui Li, Donald C. Wunsch, Edgar O'Hair, Michael G. Giesselmann

Electrical and Computer Engineering Faculty Research & Creative Works

This paper uses data collected at Central and South West Services Fort Davis wind farm to develop a neural network based prediction of power produced by each turbine. The power generated by electric wind turbines changes rapidly because of the continuous fluctuation of wind speed and direction. It is important for the power industry to have the capability to perform this prediction for diagnostic purposes—lower-than-expected wind power may be an early indicator of a need for maintenance. In this paper, characteristics of wind power generation are first evaluated in order to establish the relative importance for the neural network. A …

Saturation Routing For Asynchronous Transfer Mode (Atm) Networks, Jose Luis Ucles

Dissertations

The main objective of this thesis is to show that saturation routing, often in the past considered inefficient, can in fact be a viable approach to use in many important applications and services over an Asynchronous Transfer Mode (ATM) network. For other applications and services, a hybrid approach (one that partially uses saturation routing) is presented. First, the minimum effects of saturation routing are demonstrated by showing that the ratio, defined as f, of routing overhead cells over information cells is small even for large networks. Second, modeling and simulation and M/D/l queuing analysis techniques are used to show that …

Optimization Of Real-Time Protocols For Wireless Packet-Switched Multimedia Networks Based On Partially Observed Multivariate Point Processes, William S. Hortos

Electrical Engineering and Computer Science Faculty Publications

Next-generation wireless networks have been designed to transport integrated multimedia services based on a cellular extension of a packet-switched architecture using variants of the Internet protocol (IP). Each call, arriving to or active within the network, carries demand for one or more services in parallel, where each service type has a guaranteed quality of service (QoS). Admission of new calls to the wireless IP network (WIN) from the gateway of a wired network or from a mobile subscriber (MS) is allowed by call admission control (CAC) procedures. MS roaming among the nodes of the WIN is controlled by handoff procedures …

Current Oscillations In The System Of Carbon Steel/Phosphoric Acid/Platinum, Shao-Yuan Shi, Jin-Ping Wu, Jing Liu, An Lin

Journal of Electrochemistry

The periodic,aperiodic, chaotic and mixed-mode oscillations can occur in the process of the anodic electrodissolution of carbon steel in the solution of dilute phosphoric acid. More plentiful dynamic behaviors can be found in this system compared with the system of Fe/H₃PO₄/Pt.

Characterization And Electrochemical Investigation Of Boron-Doped Mesocarbon Microbeads Anode Materials For Lithium-Ion Battery, Mao-Hui Chen, Guo-Tao Wu, Guang-Ming Zhu, Jin-Kua You, Zu-Geng Lin

Journal of Electrochemistry

The anodic performances of boron doped and undoped mesocarbon microbeads(MCMBs) were comparatively studied and the structures were characterized by XPS, SEM, XRD and electrochemical measurements. It was found that boron doping samples greatly increased the degree of graphitization and the crystallite size, leading to quite different morphology. Electrochemical discharge/charge cycle tests indicate that lithium intercalation occurred at a little higher potential for the boron doped MCMBs, being attended by greater irreversible capacity loss.

Empirical Modeling And Vision Based Control For Laser Aided Metal Deposition Process, Mallikharjuna R. Boddu, Srinivas Musti, Robert G. Landers, Sanjeev Agarwal, Frank W. Liou

Mechanical and Aerospace Engineering Faculty Research & Creative Works

This paper gives a brief description of the laser aided manufacturing process. Empirical models describing the process dynamics of the laser aided metal deposition process is developed based on some of the models found in the literature. These models provide the basis for process planning and real time control. An embedded vision system, a two color temperature sensor, and a laser displacement sensor are incorporated for real time monitoring and control of the deposition process. The temperature profile of the surface and geometric characteristics of the melt pool are studied to ensure consistent operation of the process.

Design Of A Control System For Fmc Jetway Systems' Teleradial Bridge, Briclyn Jon Rogers

Undergraduate Honors Capstone Projects

FMC Jetway Systems has been manufacturing and servicing airport products for over forty years. These products include passenger boarding bridges, pre-conditioned air units, potable water systems and solid-state 400 hertz converters. Components produced by Jetway can be found on over 190 airports across the world. Their Apron Drive Passenger Boarding Bridge (Fig. 1) is the most versatile and widely used boarding bridge in the world. Only recently has the company aimed at gaining a portion of the quickly expanding market of commuter flights.

Real-Time Travel Time Estimation Using Macroscopic Traffic Flow Models, Pushkin Kachroo, Kaan Ozbay, Antoine G. Hobeika

Electrical & Computer Engineering Faculty Research

This paper presents the estimation of travel time on highways based on macroscopic modelling. The focus is on real-time values as compared to average or static values. The macroscopic models are used for distributed and time/space lumped settings and corresponding travel time estimation functions and algorithms are developed. The implications of these algorithms for the implementation of various incident management and traffic control strategies are also discussed.

Representation Of Gyromagnetic Composite Media For Fdtd Modeling, Marina Koledintseva, James L. Drewniak, Xiaoning Ye

Electrical and Computer Engineering Faculty Research & Creative Works

A composite media containing particles with a high internal field of magnetic anisotropy (hexagonal ferrites) useful for numerous EMC applications in a wide frequency band is considered. Effective constitutive parameters of a high-loss composite gyromagnetic media are represented in the Lorentzian form. It is convenient for the numerical analysis using the finite-difference time-domain (FDTD) algorithm with a recursive convolution procedure. The equations for the electric and magnetic field updating in such media are represented.

Electromagnetics, David V. Arnold, Richard H. Selfridge, Karl F. Warnick

Faculty Publications

Many applications of electrical engineering require a knowledge of the behavior of voltages and currents in electronic devices and within conductors. In many other situations it is not enough to understand the behavior the voltages and currents in just the conductors and other components, but also the influence of the voltage and current on surrounding materials.

Microcavity Surface Emitting Laser, Stewart Feld, John P. Loehr, James A. Lott

AFIT Patents

A three-dimensional waveguiding structure for a microcavity surface-emitting laser is described in which native aluminum oxide layers provide control of intracavity waveguiding and the laser optical mode structure of the emitted beam. Microcavity lasers described herein account for the blueshift of the emission wavelength as the laser lateral dimensions are reduced to or below the emission wavelength.

Aurora Working Group: Dsr Front End Lvcsr Evaluation — Baseline Recognition System Description, Naveen Parihar, Joseph Picone

Publications

In this document we describe the features of the baseline system to be used in the Distributed Speech Recognition (DSR) front end large vocabulary continuous speech recognition (LVCSR) evaluations being conducted by the Aurora Working Group of the European Telecommunications Standards Institute (ETSI). The objective of these evaluations is to determine the robustness of different front ends for use in client/server type telecommunications applications. As such, our experiments are designed to test the following focus conditions on the DARPA Wall Street Journal (WSJ0) corpus using a 5000-word closed-loop vocabulary and a bigram language model:

1. Additive Noise: six noise conditions …

Feedback Correction Of Angular Error In Grating Readout, Monish Ranjan Chatterjee, Sundaram Ramachandran

Electrical and Computer Engineering Faculty Publications

Angular and wavelength READ beam errors in holographic interconnection systems are often a recurrent problem. Several strategies have been proposed to minimize or eliminate such READOUT misalignments.

Some years ago, Chatterjee and co-workers proposed a method involving READ beam wavelength tuning to correct output angular errors. In this paper, we investigate the possibility of using an acousto-optic (A-O) Bragg cell with optoelectronic feedback to dynamically correct the scattered beam for deviations in the incidence direction of the READ beam of a hologram. The concept here is based on an acoustic frequency feedback strategy used recently by Balakshy and Kazaryan for …

Simulation Optimization Studies Of Routing And Process Flow Problems, Satish Ravichandran

Electrical & Computer Engineering Theses & Dissertations

Computer aided simulation is emerging as a powerful tool for numerical analysis and in conducting performance evaluations of complex systems that depend on a multitude of variables. The primary objective in such simulation studies is to gauge the performance of the system under a various constraints and operating conditions. The effects of changing the operating parameter space can thus be analyzed without having to implement costly changes. Simulations are also carried out for the baseline scenarios to verity and validate the basic underlying system model. In this thesis research, two practical problems were studied through numerical modeling, and optimized solutions …

Pulsed Electron Heating Of Atmospheric Pressure Air Glow Discharges, Hisham Merhi

Electrical & Computer Engineering Theses & Dissertations

By applying electric field pulses of short duration (compared to the time constant for glow-to-arc transitions) to a weakly ionized gas, the electron energy distribution can be temporarily shifted to higher energies. This effect causes a nonlinear increase in the ionization rate and consequently a larger electron decay time. This effect has been demonstrated using single pulse operation.³ In order to generate plasma with semi-continuous electron density, repetitive operation is required. As a first step towards repetitive pulsed electric field operation, the temporal development of the voltage across the plasma for two subsequent pulses was measured. The dual pulse …

Bi-Decomposition Of Multi-Valued Relations, Alan Mishchenko, Marek Perkowski, Bernd Steinbach

Electrical and Computer Engineering Faculty Publications and Presentations

This presentation discusses an approach to decomposition of multivalued functions and relations into networks of two-input gates implementing multi-valued MIN and MAX operations. The algorithm exploits both the incompleteness of the initial specification and the flexibilities generated in the process of decomposition. Experimental results over a set of multi-valued benchmarks show that this approach outperforms other approaches in the quality of final results and CPU time.

Globally Convergent Approximate Dynamic Programming Applied To An Autolander, J.J. Murray, Richard Saeks, C.J. Cox, George G. Lendaris

Complex Systems Faculty Publications and Presentations

A globally convergent nonlinear Approximate Dynamic Programming algorithm is described, and an implementation of the algorithm in the linear case is developed. The resultant linear Approximate Dynamic Programming algorithm is illustrated via the design of an autolander for the NASA X-43 research aircraft, without a priori knowledge of the X-43's flight dynamics.

Human Head-Neck Response To Impact Acceleration: Comparison Of Oblique To Combined Frontal And Lateral Response, Salvadore J. Guccione Jr., Edit J. Kaminsky

Electrical Engineering Faculty Publications

This paper relates human oblique head-neck kinematics to human frontal and lateral head-neck kinematics for three subjects of varying anthropometry. Head-neck kinematic response to indirect impact acceleration for an oblique test is compared to the superposition of the head/neck behavior of appropriate frontal and lateral tests for the same subject. The results have important implications in terms of the complexity required in the design and validation of omni-directional biofidelic crash test manikins and mathematical models of human head-neck response.

Turbo Space-Time Coded Modulation : Principle And Performance Analysis, Dongzhe Cui

Dissertations

A breakthrough in coding was achieved with the invention of turbo codes. Turbo codes approach Shannon capacity by displaying the properties of long random codes, yet allowing efficient decoding. Coding alone, however, cannot fully address the problem of multipath fading channel. Recent advances in information theory have revolutionized the traditional view of multipath channel as an impairment. New results show that high gains in capacity can be achieved through the use of multiple antennas at the transmitter and the receiver. To take advantage of these new results in information theory, it is necessary to devise methods that allow communication systems …

Modeling, Design And Scheduling Of Computer Integrated Manufacturing And Demanufacturing Systems, Ying Tang

Dissertations

This doctoral dissertation work aims to provide a discrete-event system-based methodology for design, implementation, and operation of flexible and agile manufacturing and demanufacturing systems. After a review of the current academic and industrial activities in these fields, a Virtual Production Lines (VPLs) design methodology is proposed to facilitate a Manufacturing Execution System integrated with a shop floor system. A case study on a back-end semiconductor line is performed to demonstrate that the proposed methodology is effective to increase system throughput and decrease tardiness. An adaptive algorithm is proposed to deal with the machine failure and maintenance. To minimize the environmental …

Joint Source Channel Coding For Progressive Image Transmission, Minyi Zhao

Dissertations

Recent wavelet-based image compression algorithms achieve best ever performances with fully embedded bit streams. However, those embedded bit streams are very sensitive to channel noise and protections from channel coding are necessary. Typical error correcting capability of channel codes varies according to different channel conditions. Thus, separate design leads to performance degradation relative to what could be achieved through joint design. In joint source-channel coding schemes, the choice of source coding parameters may vary over time and channel conditions. In this research, we proposed a general approach for the evaluation of such joint source-channel coding scheme. Instead of using the …

Novel Multiuser Detection And Multi-Rate Schemes For Multi-Carrier Cdma, Pingping Zong

Dissertations

A large variety of services is [sic] expected for wireless systems, in particular, high data rate services, such as wireless Internet access. Users with different data rates and quality of service (QoS) requirements must be accommodated. A suitable multiple access scheme is key to enabling wireless systems to support both the high data rate and the integrated multiple data rate transmissions with satisfactory performance and flexibility. A multi-carrier code division multiple access (MC-CDMA) scheme is a promising candidate for emerging broadband wireless systems. MC-CDMA is a hybrid of orthogonal frequency division multiplexing (OFDM) and code division multiple access (CDMA). The …

Propagation And Scattering Of Collimated Beam Wave In Vegetation Using Scalar Transport Theory, Michael Yu-Chi Wu

Theses

The scalar time-dependent equation of radiative transfer is used to develop a theory of pulse beamwave propagation and scattering in a medium character ized by many random discrete scatterers which scatter energy strongly in the forward scattering direction. Applications include the scattering of highly collimated millimeter waves in vegetation and optical beams in the atmosphere. The specific problem analyzed is that of a periodic sequence of Gaussian shaped pulses normally incident from free space onto the planar boundary surface of a random medium half-space, such as a forest, that possesses a power scatter (phase) function consisting of a strong, narrow …

Performance Of Proton Exchange Membranefuel Cell With Co/H2 Fuel, Hong-Mei Yu, Zhong-Jun Hou, Bao-Lian Yi, Ke-Wan Bi, Jing-Xin Zhang, Zhi-Yin Lin, Ming Han

Journal of Electrochemistry

Fuel of proton exchange membrane fuel cell(PEMFC) mostly comes from reformatecontains CO which will poison the fuel cell electrocatalyst. The effect of CO on the performance of PEMFC was studied in this paper. The results of the experiment show that when CO is fed inPEMFC ,the cell voltage will be decreased violently,then it will become steady with some vibration. The poison will become more serious with higher CO content and weaker at higher temperature. The adsorption of CO on the electrocatalyst is reversible. The PtRu electrocatalyst is moresuitable for the electrocatalysis of CO/H₂ than Pt electrocatalyst.

Study Of The Oxidation Dynamics Of Tizro2 Metal-Ceramics, Wen-Chao Li, Li-Dong Teng

Journal of Electrochemistry

The oxidation dynamics of hot-pressed Ti-ZrO₂ metal-ceramics with the compositionof 50 vol.% Ti and 50 vol.% ZrO₂ has been studied.Thermodynamic analysis shows that Ticould react with O₂ but not with N₂ in the oxidizing process of TiZrO₂ composites at 0.1 MPa air. The oxidation dynamic behavior of Ti-ZrO₂ composites is analogous to that of pure Ti. Theactivation energy for the oxygen diffusion in Ti-ZrO₂ composites is higher than that in Ti solutions, for the presence of ZrO₂ restrains the oxygen diffusion in Ti-ZrO₂ composites. At early stagethe oxidation of Ti-ZrO_{2 …}

Preparation And Properties Of Separator For Lithium-Ion Battery, Xu-Mei Ren, Feng Wu, Chuan Wu, Han-Jun Li, Xue-Jie Huang

Journal of Electrochemistry

Lithium-ion batteries are well adapted to the new multimedia applications. PP/PE based microporous film is commonly used as separator in commercial lithium ion batteries. Herewe report a microporous film which is superior to the commercial available separator. The microporous PVDF polymer separators were prepared by the phase inversion process. The pore size of the separator is Φ 7 μm , and it's porosity is 75 %. The membrane in LiPF₆-EC/DEC showedhigh ionic conductivity (above 10^-3 S/cm at room temperature), and good mechanical properties(10³ kg/cm²). The half-cells consisted of Li/PVDF separator/MCMB showed excellent cyclingcharacteristics and …

Performance Of A Direct Methanol Fuel Cell, Zhao-Bin Wei, Jian-Guo Liu, Ya-Guang Jiao, Wei-Jiang Zhou, Wen-Zhen Li, Li-Kang Chen, Qin Xin, Bao-Lian Yi

Journal of Electrochemistry

A direct methanol fuel cell with 9cm² active area consists of Pt-Ru/C anode ,Pt/Ccathode and Nafion 115 membrane. The effect of operating conditions: methanol solution concentration, oxygen pressure and cell temperature on the cell performances was investigated. The results show that performance of single cell was enhanced by increasing oxygen pressure and celltemperature ,and a maximum power density 75 mW/cm² was obtained in the range of 250-300mA/cm² current density, 0.2 MPa oxygen pressure, 1.0 mol/L methanol concentration and 75 ℃ cell temperature. When cell operating at room temperature, a relatively low, but a stable performance of cell …

The Effect Of Preparation Condition On The Photoelectrochemical Performance Of Both The Pani Film And Tio2-Pani Composite Film On Au, Huai-Guo Huang, Hong-Ping Zhang, Zhi-Xin Zheng, Yan-Yan Xi, Ling-Ling Wu, Zhong-Hua Lin

Journal of Electrochemistry

Both the PANI (polyaniline) film and TiO₂-PANI composite film on the PATP(paminothiophenol)/Au substrate were obtained under different preparation condition by electrochemical methods, and their photoelectrochemical performances were alo studied. The resultsshowed that the photoelectrochemical performances of the films depend deeply on the comditionsof preparation. The self-assembling of PATP favors the adhesion of PANl. The partially-oxidizedPANI has a greater photoelectrochemical response than that of the reduced PANI and oxidized PANl. There is an optimum of film thickness for the photoelectrochemical performance of PANI film. Heat treating is in favor of the photoelectrochemical performance of TiO₂, but decreases …

New Progress In Studies Of Lithium Nickel Oxide As Positive Electrode Materials Of Lithium Ion Batteris, Han-San Liu, Yong Yang, Zhong-Ru Zhang, Zu-Geng Lin

Journal of Electrochemistry

Lithium nickel oxide as the positive electrode of lithium ion batteries has aroused more and more interests.This paper reviews the recent reserches on synthesis and element-substitution of LiNiO₂ cathode material,and summarizes the intrinsical relationship between properties and sturcture of the material.The developments of new synthesis methods and mutilsubstitution of the material are expecting to be studied in the future research.