Digital Commons Network^™

A New Approach To Signal Registration With The Emphasis On Variable Time Delay Estimation, Mohamad Namazi, John A. Stuller

Electrical and Computer Engineering Faculty Research & Creative Works

Signal Registration is Concerned with the Problem of Estimating a Varying Displacement between Two Random Processes. We Approach Signal Registration Here as a Recursive Demodulation Problem in Which the Recursion is between Signal Estimations and Displacement Estimation. Special Attention is Given to the Problem of Estimating a Variable Time Delay. Thus, We Present New Algorithms for Estimating D(T) from Received Processes:

r₁(t) = s(t) + n₁(t)

R₂(t) = s(t - D(t)) +n₂(t)

Where s [Formula Omitted] is Signal and n₁ (•) and n₂ (•) Are Noise. Simulation Results Are Presented …

Ada Tools For The Description And Simulation Of Digital Signal Processing Systems, Mark D. Happel

Retrospective Theses and Dissertations

While specialized hardware description languages allow for maximum capability and efficiency in a design automation system, the use of a general purpose language in the same role can make the system more available or more available or more practical for a larger set of users. This project demonstrates the use of ADA* for the description and simulation of small digital signal processing systems. Building on conventions and primitives proposed by Denyer and Renshaw, a simple subsystem was described in ADA and then tested with a small simulator also written in ADA.

* ADA is a trademark of the United States …

Recombination-Current Suppression In Gaas P-N Junctions Grown On Algaas Buffer Layers By Molecular-Beam Epitaxy, D. P. Rancour, M. R. Melloch, R. F. Pierret, Mark S. Lundstrom, M. E. Klausmeier-Brown, C. S. Kyono

Department of Electrical and Computer Engineering Faculty Publications

n+pp+GaAs and n+pP+ GaAs/GaAs/Al0.3Ga0.7As mesa diodes have been fabricated from films grown by molecular‐beam epitaxy. The diodes made from films employing an AlGaAs buffer layer show marked improvements (a factor of 5 reduction) in recombination current densities. Deep level transient spectroscopy measurements moreover indicate that deep level concentrations are reduced by the AlGaAs buffer.

Compiling Unit Clauses For The Warren Abstract Machine, George D. Herbert

UNF Graduate Theses and Dissertations

This thesis describes the design, development, and installation of a computer program which compiles unit clauses generated in a Prolog-based environment at Argonne National Laboratories into Warren Abstract Machine (WAM) code. The program enhances the capabilities of the environment by providing rapid unification and subsumption tests for the very significant class of unit clauses. This should improve performance substantially for large programs that generate and use many unit clauses.

Computer-Aided Testing Of Electrical Machines: Software Development, Max Darwin Anderson, Steven A. Hauk, Robert Laramore, Hardy J. Pottinger

Electrical and Computer Engineering Faculty Research & Creative Works

Computer-aided test stations have been developed for research, experimentation, and testing of electric motors and generators. Data acquisition and control of the machines and drives are provided through a computer and its interfaces. Machines are connected to the computer through transducers for data acquisition, and power electronic drives for machine control. General software was written to enable the monitoring of all transducers continuously on the CRT screen while giving the user manual control of the machines and drives. Specialized software was written for automatic control of the induction, dc, and synchronous machines for specific experiments on each type of machine. …

Implementation And Performance Analysis Of Numerical Algorithms On The Mpp, Flex/32, And Cray/2, Raad A. Fatoohi

Electrical & Computer Engineering Theses & Dissertations

This dissertation presents the results of the implementation of a number of numerical algorithms on three parallel/vector computers. The object of this research is to determine how well, or poorly, a number of numerical algorithms would map onto three different architectures and to analyze the performance of these architectures using these algorithms. These algorithms are: a relaxation scheme for the solution of the Cauchy-Riemann equations, an ADI method for the solution of the diffusion equation, and a compact difference scheme for the solution of two-dimensional Navier-Stokes equations. The computers were chosen so as to encompass a variety of architectures. They …

The Design Of A Resonant Post Waveguide Filter, Ramjee Prasad

Tanzania Journal of Engineering and Technology (TJET)

A seven stage, quarter-wave coupled, single post, resonant cavity type waveguide filter has been studied. The posts are placed according to the Tchebyscheff distribution. The filter is designed and fabricated to meet the following specifications: Centre frequency: 9.31 GHz, Number of stages = 7, 3-dB bandwidth = 300 Mhz, Ripple tolerance in the passband = 0.5 dB. The frequency behaviour of this filter has been experimentally studied and is in close agreement with the specifications.

Gain Margin And Phase Margin Interrelationships, M Luhanga

Tanzania Journal of Engineering and Technology (TJET)

The gain margin and the phase margin Of a control SY Stem are important parameters in the determination of the relative stability of control system. In this paper We derive general interrelationships between these parameters.

A Frequency Domain Digital Signal Processor For Laser Velocimeter Systems, Andreas Evangelos Savvakis

Electrical & Computer Engineering Theses & Dissertations

A new signal processor for laser velocimeter systems is proposed. The proposed processor incorporates automatic initialization, real time operation, and can efficiently process input signals comprised of as low as 150 photons, with mean oscillation frequency up to 100 MHZ, and input turbulence from 0 to 20%. A bank of digital bandpass filters is employed for the energy spectrum estimation of the input signal. A deterministic model is developed to describe the relationship between the filter output energies and the input signal parameters. The input frequency is estimated by linearly weighting the filter output energies. A spline function approximation approach …

Multi-H Continuous Phase Modulation : Its Properties And Analysis, Jyung-Cheng Chen

Theses

Multi-h CPM, a generalization of CPFSK and also one of the so-called Combined Modulation and Coding schemes, is useful in digital communication systems where both the bandwidth and power are constrained. The increased signal processing complexity, which can be viewed as the third communication resource, is used to trade for both power and bandwidth, and to approach the error-free communication promised by Shannon's theorem.

The transmitted multi-h CPM signal carries a coded sequence of continuous phase changes; the possible phase states form a cylindrical trellis in phase and time, in which the modulation indices are reused in a cyclical fashion. …

Relationship Between The P And S Fresnel Reflection Coefficients Of An Interface Independent Of Angle Of Incidence, R. M.A. Azzam

Electrical Engineering Faculty Publications

The Fresnel reflection coefficients r_p and r_s of p- and s-polarized light at the planar interface between two linear isotropic media are found to be interrelated by (r_s - r_p)/(1 - r_sr_p) = cos 2β, independent of the angle of incidence ø, where tan²β = ∊ and ∊ is the (generally complex) ratio of dielectric constants of the media of refraction and incidence. This complements another relation (found earlier), (r²_s - r_p)/(r_s - r_sr_p) = …

The Acquisition Of Direct Sequence Spread Spectrum Communication Systems, Anthony Donald Demeri

Theses

This Paper surveys different techniques of acquiring Direct Sequence Spread Spectrum Systems.

It classifies different systems, indicates the strongpoints and weakness of each, along with some applications.

One method, The Single Dwell Serial PN Acquisition System is then focused on in detail. The detail includes analysis of standard version, derivation of the mean time to acquire, the variance, the probability of detection and the probability of a false alarm.

In the last section of the paper the analytical results of the Single Dwell Serial PN Acquisition System shall be confirmed by computer simulation.

Reliability Study Of Liquid Crystal Display, Kalpesh Mahendra Desai

Theses

The purpose of this thesis is to study the reliability of liquid crystal display under different temperature conditions. To accomplish this, accelerated life testing was done on the soft glass and the hard glass liquid crystal display units at 77 C and 85 C temperature without any added humidity or voltage.

As the current is a usefu1 indicator for probable wear of liquid crystal display, leakage current was measured at 0 hour, 1000 hours, 2000 hours and 3000 hours when the units have stabilized at room temperature.

The date shows higher spread for the hard glass units. This may indicate …

Computer-Aided Design Of A Waveguide To A Suspended Stripline Transition For Millimeter-Wave Applications, Hsin-Yen Peng

Theses

Realization of millimeter-wave systems on suspended striplines necessitates transitions from such lines into waveguides for measurements and other purposes. Transition can be obtained through coupling TE10 mode in the waveguide into a TEM mode in the suspended stripline. A continuous transition using tapered complementary unilateral finline and two gradually increasing conducting tapered ridges is studied here. The tapered region is modelled using a number of uniform sections with gradually changing cross sections. The junction separating the tapered section from the suspended stripline is modelled via physically and electrically continuous terminations. Physical continuity approach is more flexible for manufacturing purpose at …

The Dielectric Slab-Wedge Antenna, B. Keith Christensen

Theses

A theoretical model and numerical investigation of the directive gain of a dielectric slab-wedge radiator is presented. The model is based on a union of the classical dielectric slab equations, local mode theory, and equivalent current distribution treatments of the truncated dielectric slab and wedge geometries.

The far field is developed from the sum of two current distributions. The slab region, up to the transition plane between slab and wedge, is replaced by equivalent electric and magnetic surface current densities. The wedge contribution is developed from a volume polarization current distribution.

Conservation of power is used to approximate the field …

Microcomputer Local Area Network Interface, David W. Juan

Theses

A Microcomputer Local Area Network Interface system for use in the study of Local Area Network has been built and tested. The special feature of the system is data transmission/receiving and error detection/recovery. The system adapted the International Standards Organization (ISO) Open System Interconnection COSI) model. It used the star topology and implemented the physical layer, data link layer and network layer. The results of the system indicated the data communications and resources—sharing between microcomputers.

Linearization Accuracy In Probabilistic Load Flow, Guan-Zhong Liang

Theses

This paper presents a linear load flow method which can be used for probabilistic load flow analysis. The method is based on least-square estimation. To estimate its accuracy in linear load flow calculations, the method and a previously developed linear load flow method are applied to a typical power system and the results evaluated. Comparable accuracy is noted.

Design And Evaluation Of Performance For The Multi-Microprocessor System, Sang-Soo Lee

Theses

A tightly coupled multiple-microprocessor with two MPU's that can be run at different clock speeds has been built and tested. The method of interconnection for this multiprocessor is a timeshared common bus with shared memories having a tightly coupled architecture. The signal timipg of the multiprocessor system for different speeds has been investigated using a logic analyzer for simulation modeling. The desired timing results have been obtained. According to the timing results, the simulation model for the General Purpose Simulation System has been correctly designed and performance of the multiprocessor system for the various clock speeds has been evaluated by …

Nervous System Simulation, Jian Chen

Theses

This thesis deals with the nervous system simulation. The Hodgkin-Huxley model and Stein's model are used as basic tools. The author has tried to describe some practical problems by mathematical models.

First, the horse-shoe crab eye is investigated. Light intensity is reported to the brain by the firing frequency of the photoreceptoe. A Poisson process is used to simulate the stimulus to the receptor. The result of the stochastic model coincides with the theoretical one: receptor overlapping decreases the resolving power of the eye; and the lateral inhibition compensates the effect of overlapping.

Second, a nerve muscle model was set …

An 8052 Ah - Basic, Based Development System, Suresh Vishwanath Leley

Theses

This project exploits the latest in microcontrollers-an entire environment for developing and prototyping a microcontroller application. With one key chip, a little glue, and a Dumb terminal a powerful system is achieved at a vanishingly small cost. This "one chip" system is adequate for realizing a wide range of applications calling for a small computer or an embedded processor.

Besides economy of system cost, the turn around time from concept to functioning application can be extremely short, even when the development engineer is not particularly well acquainted with traditional assembly language and microprocessor development practices. This economy is achieved by …

An Analysis Of Minimum Shift Keying From The Viewpoints Of Quadrature Multiplexed And Multi-H Continuous Phase Modulation Signaling, Alfred Anthony De Seta

Theses

Minimum Shift Keying (MSK) is a bandwidth efficient modulation scheme which offers superior performance over Quadrature Phase Shift Keying (QPSK) and Offset Quadrature Phase Shift Keying (OQPSK). This paper discusses these modulation techniques from a quadrature multiplexed signaling viewpoint and compares them in terms of error performance, bandwidth properties and bandlimiting and hardlimiting effects. MSK is also considered as a special case of a multi-h Continuous Phase Modulation (CPM) signal and the Viterbi algorithm is presented as an optimal detection scheme for this class of signals. A computer simulation is performed with the VA as the detection mechanism for an …

A Computer Aided Manufacturing System For Small Quantity Prototype Board Production, Santiago Garcia-Perez

Theses

A matrix addressed manufacturing tool has been built, tested, and integrated in a system aimed to exploit wire-wrap wiring technology for protoboard production in small quantities. Extensive software exploits the power and economy of the personal computer as a superb manufacturing tool and documentation system. Computer graphics are used as a visual aid that takes advantage of the cognitive capabilities of the human mind and eliminates the boredom and high costs involved with heavy automation achieving instead a tolerable level of human engagement with significantly increased efficiency. The approach presented is new and delivers substantial gains in productivity. The software …

Design And Applications Of A Graphics Package For The Hp1000 Computer., Hsiao-Chih George Lee

Electronic Theses and Dissertations

The objective of this thesis is to develop the FORTRAN subroutine PLOTER which is a general-purpose plotting tool to plot charts on a Hewlett Packard plotter. The programs RESP and INVLAP which can plot the frequency and time responses of system functions are modified to adopt the PLOTER subroutine and are stored of the HP1000-A900 minicomputer whose software, the GRAPHICS/1000, supports the graphics ability of PLOTER. This thesis describes the theories, functions, software techniques and operations of the PLOTER subroutine and the application programs RESP and the INVLAP. It also provides program listings and example plots.

A Unit Of Instruction In Fiber-Optic Communication, Ronald Struble

Graduate Research Papers

The purposes of this research project were to:

1. Review the historical developments, components, and applications of optical fiber in communications.

2. Develop a laboratory exercise to demonstrate fiber-optic communication.

3. Construct equipment to demonstrate the use of fiber optics in communication. This equipment is used in the laboratory exercise.

Design Of Code Division Multiple Access Systems, Nakrendrakumar Patel

Theses

The intent of the work "Design of Code Division Multiple Access systems (CDMA) " is to consider different aspects of design with their effect on system performance. The generation of binary shift register sequences, that is maximal length sequences, with their properties are presented. From these maximal length sequences the Gold codes are obtained which are the most suitable approximately orthogonal codes for designing CDMA systems. These are discussed with their specific crosscorrelation properties. An extensive discussion is given of the difficult problem of synchronization, thatis bothacquisitionandtracking of pseudonoise sequences. Different synchronizing methods are discussed along with their relative performance. …

Optimization Of Reactive Ionized Cluster Beam (R-Icb) Technique For Deposition Of Gan Films, Veronica S. Kyriacou

Theses

The deposition of GaN film onto glass substrate, using the Reactive - Ionized Cluster Beam deposition technique was studied. The creation of clusters is dictated by various parameters such as the vacuum pressure inside and outside the crucible, the crucible temperature, and the nozzle diameter of the crucible. Optimization of these parameters was experimentally studied, and deposition of gallium films on glass substrates was tried as a first step.

The direct heating method was used at first to get the 1100¬1300°C crucible temperature which was required for the creation of gallium clusters. Although different tungsten wire diameters and different number …

The Gpib User's Manual For Hx-40, Ding-Tang Li

Theses

A completed RS-232 to GPIB interfacing system has been built for HX-40 to master the GPIB oriented machine through its serial port. GPIB commands and data can be transfered between HX-40 and the slave station, which is a HP 3582A spectrum analyzer in this project. The data acquisition from serial to GPIB is done by a well-made GPNET mode 10 interfacing board in a transmitting rate of 9600 baud rate. GPNET exchanges data and commands with HX-40 through a RS-232 port, and passes them to the slave station through a GPIB port which is coordinated by GPIB protocol. A software …

The Interfacing Between The A/D Converter, Buffer Memory And Hx-40 Microcomputer, Yu-Hwa Chu

Theses

The data acquisition system which includes A/D converter, buffer memory, and address generator, is to digitize the signal for the computer use. The special feature of this system is the computer controlled digitizing rate over a range from 35K to 0.

The interfacing between Motorola 68000 E.C.B. to H.P. 64000 Development System is the simple example for data communication. How to make the protocal to be compatible is the main point. H.P. 64000 is treated as a host computer because it has the capability for data management and large memory for storing data.

Digital Signal Processing On Tms32010 Evaluation Module And Analog Interface Board, Jiming Sun

Theses

The TMS32010 Evaluation Module (EVM) and Analog Interface Board (AIB) have been used to implement a digital signal processing system. This new system will be the hardware basis for research and development in the DSP field at NJIT in the future. This thesis will serve as a user's guide and overall technical manual for the system.

TMS32010 Assembler, Linker and Simulator in VAX-11 are used to develop the system software, then we can down load the object codes to the EVM through the MODEM in order to test them. By using the A/D and D/A converter as input and output …

Design And Construction Of An Atomic Nitrogen Source For Ion Cluster Beam Deposition Of Thin Film Nitrides, Sahar Elgharib

Theses

The objective of this thesis research was to generate atomic nitrogen to react with Ga being deposited by an Ion Cluster Beam method to prepare GaN thin films. An experimental reactor was designed and constructed to generate atomic nitrogen by making use of a microwave induced discharge to dissociate molecular nitrogen into atomic nitrogen. The concentration and the flow rate of the atomic nitrogen arriving at the substrate were measured by titration with nitrous oxide. The experiments were done with 0.32 square cm quartz tubing at room temperature over the nitrogen pressure range from 0.14 torr to 0.56 torr. Results …