Digital Commons Network^™

Kinetic Behavior Of The Pt/Ysz Solid Electrolyte Interface Exposed To O2+He Mixture, Yi Jiang, Wenzhao Li, Lixin Cao, Jingwang Yan

Journal of Electrochemistry

Electrochemical behavior of the Pt/YSZ solid electrolyre interface has been investigated by cyclic voltammetry and linear potential sweep technique. It was found that the electrochemical adsorption of oxygen on the Pt surface follows the Temkin adsorption model. The amount of oxygen species increases logarithmically with time. Two oxygen species are electrochemically formed on the Pt surface. One is atomically adsorbed, the other probably subsurface oxygen or Pt oxide. The electrochemical reduction of adsorbed oxygen is kinetically irreverable. The cathodic peak potential is affected both by the potential sean rate and the amount of oxygen ahorbed on the surface. Kinetic parameters, …

Determination Of Transport Number Of The Modified Liclo4-(Peo)20 Polymer Electrolyte, Ruqi Zhou, Qngguo Liu, Weihua Qiu, Yun Zhang, Yuee Zhao, Leiling Yang

Journal of Electrochemistry

In this work a combination method of A.C. Impedance and chronoamperometry was used to determine the lithium ion transport number of LiClO₄·(PEO)₂₀·(PC)₁₂·(EC)₁₂ polymer electrolyte. It is known that lithium is thermodynamically unstable in non-aqueous or polymer electrolytes, leading to the formtion of a film on lithium surface, called as solid electrolyte interphase (SEI). The presence of SEI layer will greatly influence the experimental result of lithium ion transport number. The new method avoid the effect of SEI layer, and can give correct transport number of lithium ion in the electrolyte of DCIO_{4 …}

Preparation Techique Of Foamed Nickel By Electrodeposition, Xihua He, Ronghui Hu, Hanxi Yang, Zhengzhong Zuo

Journal of Electrochemistry

This paper describes the preparation technique and operation conditions for manufacturing foamed nickel by chemilcal pretreament, electrodeposition and heat treatment. The foamed nickel made in this method showed high porosity, uniformity and considerable strength and tenacity,applicable for various secondary battery electrodes.

The Electrochemical Behavior Of C60-Chemically Modified Poly(N-Vinylcarhzole)In 1 Mol/L Liclo4-Thf Solutions, Yu Chen, Zuen Huang, Ruifang Cai, Fupin Zhang

Journal of Electrochemistry

The electrochemical behavior of C₆₀-PNVC copolymer in 1 mol/L LiClO₄-THF solutions has been studied by cyclic voltammetry. The results demonstrated that there are considerable differences of electronic structure between PNVC (Poly (N-vinylcarbazole)) and C₆₀-PNVC copolymer, this being consistent with the ESR results and the oxidstion-reduction activarion of pure PNVC by C₆₀-chemical modification. In the potential region, 1.3V～-3.5V, five steps, 0. 90V/0.60V, 0.20V/0.00V, -1.05V/-1.30 V, -1.25V/-1.75 V, -2.00V/-2.50V, of oxidation/reduction proceases were indicated in the cyclic voltammetry for pure PNVC, whereas seven steps, 0.20V/0.20V, -0.30V/-0.50 V, -0. 60V/-0.60 V, -0.80V/-1.10 V, -1.95V/-2.10 V, …

Study On The Manufacture Of Pt/C Gas-Diffusion Electrodes, Yonglin Ma

Journal of Electrochemistry

The various methods of manufacturing gas-diffusion electrodes are reviewed and a new method of preparing the Pt/C electrocatalyst and the gas-diffusion electrodes is explored in this paper. The electrochemical performance of resulting electrodes in concentrated phosphoric acid for oxygen reduction at 150℃ are compared with the commercial electrode which purched from Giner Inc. (U. S. A). The results show that the performance of the Pt/C electrodes which manufactured by the method in this paper has been greatly improved. Therefor, a fuel cell using such electrodes has high industrial value.

Construction Of Accurate Molecular Models Using Laser Stereolithography And Determination Of Nmr Spectra For Amiloride Hydrochloride And Its Free Base, Ana Deborah Ofsievich

Theses

Accurate molecular models were constructed by a rapid prototyping process, called stereolithography. This process uses a computer-controlled laser to cure and solidify a photosensitive liquid polymer. Using a computer-aided design (CAD) program, spheres of appropriate van der Waals or CPK radii were drawn and placed in the three dimensional CAD space, in accordance with the atomic coordinates obtained from quantum mechanical calculations and from neutron diffraction data. These design data were used to drive the stereolithography system where the models were built in the same shape as the CAD image. The models built for the purpose of this work consisted …

Continuous Monitoring Of Volatile Organic Compound Emissions Using Microtrap Based Injection Technique And Gas Chromatography, Wenjun Chen

Theses

A microtrap is made by packing a small diameter tubing with an adsorbent. The microtrap can be rapidly heated with a pulse of electrical current resulting in a sharp desorption that can act as an injection for GC separation. The microtrap can be used in several configurations to concentrate and inject sample in continuous, on-line monitoring system.

In this research a laboratory scale catalytic incinerator was set up and volatile organic compounds in the incinerator effluents were monitored using the microtrap based injection systems. The detection systems used were gas chromatography and nonmethane organic carbon (NMOC) analyzer. Conventional sample valve, …

Space-Based Genetic Cryoconservation Of Endangered Species, Michael Noah Mautner

Chemistry Publications

Genetic materials of endangered species must be maintained, for cryoconservation, permanently near liquid nitrogen temperatures below 77 K. Due to the instability of human institutions, permanent safety is best provided at storage sites that maintain passively the needed low temperatures, and provide barriers to access. The required conditions are available in permanently shaded polar lunar craters with equilibrium temperatures of 8 to 40 K, on the moons of Saturn, and unshielded storage satellites. A genetic depository can be incorporated readily into planned lunar programmes.

[(Co)H(Pph3)2-Arachno-Osb3h8], Nigam Rath, J. Bould, L. Barton

Chemistry & Biochemistry Faculty Works

A single-crystal X-ray diffraction study of the species 2-carbonyl2-hydrido-trans-2,2-bis(triphenylphosphine)-2-osma-arachno-tetraborane confirms the structure as a tetraborane(10) butterfly with a trans-[(CO)H(PPh3)2Os] group replacing a BH2 group at a wing-tip or 2-position. It is compared with the previously reported ruthenaborane analogue (CO)H(PPh3)2-arachno-RuB3H8.

A New High Pressure Sapphire Nuclear Magnetic Resonance Cell, Shi Bai, Craig M. Taylor, Charles L. Mayne, Ronald J. Pugmire, David M. Grant

Faculty Publications

A new version of a single-crystal sapphire high pressure nuclear magnetic resonance (NMR) cell is described that is capable of controlling the sample pressure independent of the temperature. A movable piston inside the cell adjusts and controls the sample pressure from ambient conditions to 200 atm within plus or minus 0.3 atm. The linewidth at half-height for a 13C spectrum of carbon dioxide at 15degrees C and 57.8 atm is found to be 0.5 Hz. The carbon dioxide gas/liquid phase transition is clearly observed by measuring 13C chemical shifts as the sample pressure approaches equilibrium. The time required for this …

Microhollow Cathode Discharges, K. H. Schoenbach, R. Verhappen, R. Tessnow, F. E. Peterkin, W. W. Byszewski

Bioelectrics Publications

The current–voltage characteristics of hollow cathode discharges and their predischarges in argon under dc and pulsed conditions were found to have a positive slope at pressures up to approximately 50 Torr, and currents up to 20 mA, at a hole diameter of 0.7 mm. In this range of pressure and current, parallel operation of hollow cathode discharges, without ballast, was demonstrated. Scaling to higher pressure is possible by reducing the hole diameter. Pulsed experiments with an array of cathode rings of 75 μm diameter allowed us to obtain parallel operation of more than 50 discharges at a pressure of 350 …

Electrodeposition Of Copper Indium Sulfide Films From Organic Solutions, Arif Raza, Robert Engelken, Brandon Kemp, Imran Khan, Wasim Aleem, Chris Barber

Journal of the Arkansas Academy of Science

We report on organic solutions ofCuCl 2 ,InClg, and elemental sulfur for electrodepositing CuIn x Sv films. CuInS 2 and CuInSe 2 are promising solar cellmaterials; our work on CuInSg prefaces planned work on plating CuInSe 2 from nonaqueous solvents. Two promising solvent systems are (1) mixed propylcne carbonate and water and (2) mixed ethylene glycol, propionic acid, and water (Engelken et al., 1988). Gray-brown films ofCuInx Sy (nominally GuInS2 ) have been plated from both baths. Major problems include (1) reduction ofCu+2 to Cu and Cu x S by the solvent at high temperatures (T>l()0°C), hence depleting Cu+2,(2) …

Nucleation And Growth Of Gan On Sapphire By Mbe, Steven Buczkowski

Graduate Theses, Dissertations, and Problem Reports (ETD)

GaN was grown by molecular beam epitaxy in an effort to determine nucleation and growth conditions which lead to high quality, single-crystal films. Atomic force microscopy (AFM) was used to show that growth under Ga-rich conditions promotes the nucleation of films with large nucleation domains leading to a lower density of intrinsic defects related to domain boundaries. These conditions are also shown to promote a 2-D growth mode resulting in films with a high degree of nucleation domain coalescence and surface roughnesses below 2 nm. Addition of atomic hydrogen, using a thermally-cracked source, is shown to increase the growth rate …

Galvanostatic Pulse And Pulse Reverse Plating Of Zinc-Nickel Alloys From Sulfate Electrolytes On A Rotating Disc Electrode, Branko N Popov, M. Ramasubramanian, S. N. Popova, Ralph E. White, K-M. Yin

Faculty Publications

Galvanostatic pulse and pulse reverse techniques have been used to study the plating of zinc–nickel alloys in the presence of nonyl phenyl polyethylene oxide. The effects of average current density, rotation speed of disc electrode and the presence of nonyl phenyl polyethylene oxide in the electrolyte on deposition of zinc–nickel alloys were evaluated. Zinc–nickel plating bath solution chemistry was studied by determining the equilibrium concentrations at various pH levels. It was found that the alloy composition was determined by solution equilibria, mass transfer of the electroactive species within the diffusion layer and by the surface coverage of nonyl phenyl polyethylene …

Biodegradation Of Nonionic Surfactants And Effects Of Oxidative Pretreatment, Craig D. Adams, S. Spitzer, R. M. Cowan

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

The aerobic biodegradability of nonionic, ethoxylated surfactants and model compounds, and the effect of advanced oxidation pretreatment on the biodegradability of the biorefractory surfactants were examined. Bioassays conducted using a mixed microbial seed showed that the linear primary alcohol ethoxylates, the fatty acid ethoxylates, and also polyethylene glycol were all degradable. The biomineralization of the linear secondary alcohol ethoxylate, ethylene oxide/propylene oxide block copolymer, and alkylphenol ethoxylate was observed to be inhibited to varying degrees. Additional bioassays were conducted on model compounds to examine the effect of specific structural components on biodegradability. Advanced oxidation pretreatment using hydrogen peroxide in combination …

Neutron Diffraction And Magnetic Studies Of Nd₂Fe₁₇₋ₓtₓ (T=Si, Mn) Alloys, William B. Yelon, Z. Hu, Mingxing Chen, H. Luo, F. Pourarian, Peter C. Ezekwenna, G. K. Marasinghe, K. H. J. Buschow, D. P. Middleton, William Joseph James

Physics Faculty Research & Creative Works

We have carried out neutron and magnetic studies on Nd₂Fe_17-xT_x (T=Si, Mn) alloys. the unit cell of the compounds contracts with both Si and Mn substitution. Si atoms avoid the 6c site, prefer the 18h site strongly, fill the 9d site steadily and fill the 18f site only at relatively high Si concentration. Mn atoms avoid the 9d sites but prefer the 6c site strongly, while the 18f site and 18h site fill slowly. the Si site occupancies appear to be dominated by the crystal environment while the Mn site occupancies are dominated by steric …

Treatability Of S-Triazine Herbicide Metabolites Using Powdered Activated Carbon, Craig D. Adams, Tammy L. Watson

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Widespread use of s-triazine herbicides such as atrazine, simazine, and cyanazine has led to the contamination of many ground-water and surface-water supplies with the parent compounds as well as by primary metabolites (e.g., deethylatrazine, deisopropylatrazine, and deethylcyanazine). Ozonation has been shown to produce many of the same byproducts. Activated carbon adsorption has been designated by the U.S. Environmental Protection Agency as the best available technology (BAT) for the treatment of herbicides in drinking water. Little data is available, however, on the applicability of activated carbon treatment for the control of the primary degradation products of herbicides. In this study, the …

Effects Of Ammonium Perchlorate On The Thyroid Hormone Levels Of The Sprague-Dawley Rat, James H. King Jr.

Theses and Dissertations

The purpose of this research was to determine the threshold dose for ammonium perchlorate (AP) in the Sprague-Dawley rat. No dose response data exist for AP and the EPA has studied literature on the subject of perchlorates to determine a provisional reference dose. The Perchiorate Group, a consortium of DoD and industry representatives, believes this provisional reference dose is too conservative. This experiment was executed to provide dose response data on which to base a more accurate reference dose. The study consisted of eight groups of 12 Sprague-Dawley rats, six male and six female, which were exposed to incremental doses …

Study Of The Long-Term Desorption Of Trichloroethylene From Clay Soils Using Infrared Spectroscopy, Mary P. Stager

Theses and Dissertations

Slow desorption of contaminants from soil presents one of the greatest challenges to modeling contaminant fate and transport and implementing effective remediation technologies. The kinetics of long-term desorption of trichloroethylene (TCE) from powdered clay soils were studied to determine the desorption rates and mechanism. Infrared absorption spectroscopy was used to monitor the concentration of TCE desorbed from contaminated flint clay for 71 hours. Observed gas phase TCE concentrations as a function of time were compared to that predicted by a one-site Langmuir desorption mechanism. The Langmuir model, with a single type of bonding site, did not account for the release …

Model Of Chlorocarbon (Cfc-12) Chemisorption On Solid Rocket Motor Alumina Exhaust Particles, Gary E. Lund

Theses and Dissertations

Solid Rocket (SRMs) that power Titan IV rockets and Space Shuttles, exhaust large quantities of potentially ozone damaging pollutants directly into the stratosphere, while in powered flight. In the past, studies on potential stratospheric impact of the exhaust products from aluminum/ammonium perchlorate based SRMs have focused on the effect of gaseous HCl from SRMs on the stratosphere. Until recently, the impact of heterogeneous chemistry on stratospheric ozone was believed to be relatively insignificant. This research investigates the potential heterogeneous process of CFC-12 dissociative chemisorption on alumina surfaces and the release of reactive halogen species known to destroy ozone. Through a …

Atmospheric Transport And Diffusion Modeling Of Rocket Exhaust, Chad A. Burel

Theses and Dissertations

Space launches at Vandenberg Air Force Base (VAFB) and the Cape Canaveral Air Station (CCAS) produce exhaust from the solid rocket boosters and liquid hypergolic fuels containing several toxic substances including hydrogen chloride and hydrazine. In order to estimate the health risk that would be imposed upon the public by proposed launches, range safety officials rely on the Rocket Exhaust Effluent Diffusion Model to predict where the exhaust chemicals will go after the launch and how strong the concentrations will be. The original REEDM program averaged the meteorological parameters (wind speed, wind direction, shear, etc.) across the entire mixing level …

Simultaneous Detection System Combining Studies Of Programmedpotential Step Technique And Time-Resolved Ftir Spectroscopy, Shigang Sun, Xiaoyu Chen, Guoqiang Lu, Wenfeng Lin, Nanhai Li, Shenpei Chen, Hongping Dai, Jiqian Mu

Journal of Electrochemistry

/

A Photoelectrochemical Investigation Of A.C.Modulated Passive Films On 304 Stainless Steel In Weak-Alkaline And Neutral Solution, Tianbao Du, Chunan Cao, Jiakang Yu, Haichao Lin

Journal of Electrochemistry

A photoelectrochemical investigation has been carried out on AISI 304 stainless steeI AV modulated passive film in 0.1mol/L Na₂B₄O₇ and 0.5 mol/L Na₂SO₄ solution. Photo current curve depends on the potential, passive condition and testing solutions. The results of the measurements indicate that the photoresponse is determined by the defects in the electronic structure of the films whenthe defects lead to localized states in the bandgap region. It is concluded that the passive film on AISI 304 stainless steel is in a highly disordered amorphous state.

Growth Kinetics And Breakdown Of Passive Films On Rebar Electrodes In Simulated Cement Pore Solution, Wei Chu, Yuanxiang Shi, Baoming Wei, Yong Yang, Xuguang Chen, Zugeng Lin

Journal of Electrochemistry

The growth kinetics and breakdown of passive films on REBAR electrodes insimulated cement solution (pH=12.5 and 13.8) have been investigated using in situ photoelectrochemical methods and potential step method. The results show that there are two mainstages in the growth of the film, with two rate functions characterized by linear relation between thefilm thickness and the direct logarithm of time. There is a sign in laser-scanning photoelectrochemical microscopic image just before the passive film breaks down. The addition of inhibitor NaNO₂ changes the growth kinetics and thickness of the film, and therefore improves the resistance of pitting corrosion induced …

Application Of Electroanalytical Chemistry In Heteropoly Compounds System──Studies On The Redox Properties Of Bis(Undecatungstometalate) Lanthanates, Weiqing Wang, Xiumei Zhang, Jingfu Liu

Journal of Electrochemistry

The redox properties of Ln(MW₁₁)₂ (M=As, Ti, Ga; Ln=La, Ce, Pr,Nd, Sm, Eu, Gd, Dy) are systematically studied. It has been found that the redox order is La(AsW₁₁)₂ > La(TiW₁₁)₂ >La(GaW₁₁)₂.The reduction process of Ln(MW₁₁)₂ anion has been discussed.

Fabrication And Electrochemical Behaviors Of Thin Films Of Polyaniline By Langmuir-Blodgett Technique And Electropolymerization, Benzeng Hua, Zhaoxiong Xie, Yanzhen Chen, Yunhong Zhang

Journal of Electrochemistry

Hydrogen-bond between stearic acid and aniline in subphase lead to Langmuir monotayers of stearic acid-aniline, the molecular area of stearic acid-aniline is 26 nm². With surfacepressure increased into 50 mN/M, the hydrogen-bond would be rearranged, aniline molecular transales into vertical from horizontal, surface pressure decreased quickly. A new kind of Langmuirmonolayer is formed instead of collapse, it's molecular area decreases into 24 nm² and thicknessin creases with 0.25 nm. After electroreduction of L-B films depeited onto the surface of SnO₂ electrode, anilne layers between two stear acid matix could be polymerized into thin films of polyanilne. …

Cyclic Voltammetric Calorimetry Studying The Deposition Of Copper Of Pt Electrodes, Yongchun Zhu, Robin. H. J. Clark

Journal of Electrochemistry

In the present paper, cyclic voltammetric calorimetry has been used to study thedeposition of copper on platinum electrode from LiClO₄ aqueous solution. Cyclic voltammetric thermogram and cyclic voltammetric differential thermogram show that the deposition of copper on theelectrode is an exothermal process with a strong interaction between copper and platinum layer (-3227.0 kJ /mol). The electrochemical oxidation of the deposited copper is composed of twoprocesses: an endothermal activation process with 747.0 kJ/mol of activation enthalpy, and an exothermal oxidation reaction with -189.9 kJ/mol of the reaction enthalpy, which are accord with the data from the theoritical estimation and thermodynamic …

Electrochemical Behaviors Of The Loaded Stainless Steel In Dilute Thiosulphate Solution, Changjian Lin, Zude Feng, Fuling Lin, Fayang Wang, Jianguang Tang, Yuanhui Wang

Journal of Electrochemistry

The electrochemical behavior of 18/8 stainless steel in dilute thiosulphate solutionduring strained loading was studied by various electrochemical techniques and scanning electronmicroscope. It is evidenced that the corrosion activity of stainless steel increased with strained loading. The dynamic process of repassivation, which may datermine the initiation, the cease and development of the stress corrosion cracking for stainless steel, was strongly influenced by both electrochemical andloading conditions. Pitting corrosion may locate preferentially on the sites which was suffered mostloading. The propagation of pitting corrosion of stainless steel may induce stress corrosion crakingunder certain conditions.

Study Of The Modified Electrolytic Manganese Dioxide, Guohui Yuan, Dewei Chu, Rihui Shen, Hongwei Pan, Cuifen Zhang

Journal of Electrochemistry

A modified electrolytic manganese dioside doped with Bi (Bi-EMD)wasprepared and examined by XRD and XPS. It is predominantly γ-mnO₂ and the Bi exists as Bi₂O₃ in the modified material. The content of Bi in Bi-EMDs increased with the increasement of Bi³⁺ concentration in electrolyte, and reached 14.3(wt)% from the bath of 0.008 mol·L^-1 Bi³⁺ used. Some Zn/Bi-EMD prototype batteries of AA size were assembled, and which cycle life tests showedthat the Bi-EMD has better reversibility.

The Composition Structure And Corrosion Resistance Of Al-Mn Alloy Plating, Jiaju Guo, Naiming Guo

Journal of Electrochemistry

The Al-Mn alloy plating was electrodeposition from low temperature molten salts (below 200℃), its chemical composition control, corrosion resistance as well as the relationshipbetween chemical composition and structure were studied. The results indicate that the main effect onchemical composition of Al-Mn alloy plating is Mn ion concentration in molten salts. The Mn contentin the range of 25～40(wt)%, Al-Mn alloy plating has amorphous structure. In 0.5 mol/L H₂SO₄ and NaCl solution ,corrosion resistance of the alloy plating is much better. When the alloy has amorphous structure, corrosion resistance of plating has been remarkably increased.