Digital Commons Network^™

Application Of Biphenyl Electroploymerization For Overcharge Protection In Li-Ion Batteries, Li-Fen Xiao, Xin-Ping Ai, Yu-Liang Cao, Han-Xi Yang

Journal of Electrochemistry

The electropolymerization of biphenyl at overcharged positive electrode was investigated for overcharge protection of Li-ion batteries. Biphenyl in electrolyte as an additive can electrochemically polymerize at 4.5～4.75 V(vs. Li/Li⁺) to form a layer of conductive film on cathode surface. The surface film increases the internal resistance and the gases released during the electropolymerization also increases the internal pressure of the batteries, which therefore enhance the sensitivities of the electrical disconnecting devices. During prolonged overcharge, the growth of the conductive polymer film can create short circuit between the positive and negative electrodes and cause self-discharge of the batteries to …

The Preparation And Characterization Of Zno-Pani Composite Film, Yan-Yan Xi, Huai-Guo Huang, Zhi-Xin Zheng, Ping Dong, Jian-Zhang Zhou, Ling-Ling Wu, Zhong-Hua Lin

Journal of Electrochemistry

ZnO nanoparticle films were prepared on the Au film, PANI film and ITO by sol-gel method, and their morphological optical and photoelectrochemical properties were also studied. The results showed that the porous structure of PANI can suppress the aggregation of ZnO particles, resulting in the blue shift of on-set in the UV-Vis spectra and fluorescence spectra of ZnO-PANI composite film compared with that of ZnO-Au film. It was suggested that the ZnO-PANI composite film can be used in photoelectric coversion.

The Electrochemical Behavior Of Amorphous Ni-P And Ni-B Alloys In 0.5 Mol/L H2So4, Xu-Cheng Wang, Wei-Jiang Wang, Hou-Tian Liu, Zu-Zhan Yu

Journal of Electrochemistry

Polarization curves and impedance spectra were used to investigate the electrochemical behavior of amorphous Ni-P and Ni-B alloys in 0.5 mol/L H₂SO₄ solutions. The possible reason about the remarkable difference in the electrochemical behavior between amorphous Ni-P and Ni-B alloys was discussed.

In Situ Measurements Of Solution Conductivity In Microwave Field, Yong-Qing Su, Chun-Peng Liu

Journal of Electrochemistry

The curves of the conductivity as a function of temperature for 24 kinds of solutions have been in situ measured both in the microwave field and in absence of microwave field. The results indicated that the relationship between the conductivity in microwave field (L_w) and temperature (T) can be expressed by an equation L_w=a′+b′T+c′T² , similar to the one that is valid in absence of the microwave field L_n=a+bT+cT². Conductivity in the absence and presence of microwave field can be linked by the equation lnL_w=A+BL_n+CL²_{n …}

An Eqcm Study Of Water Adsorption And Oxidation On Pt Electrodes In Sulfate Acid Sulotions, Heng Lin, Sheng-Pei Chen, Jin-Mei Lin, Ai-Lan Lin, Guo-Liang Chen

Journal of Electrochemistry

Simultaneous frequency and current responses during potential cycling of Pt electrode were measured in 0.1 mol·L^-1 H₂SO₄ solution by using EQCM. Quantitative analysis of the mass change revealed that the increase of mass in the hydrogen and double-layer regions in a positive-going potential scan was due to water adsorption on the Pt electrode, further calculation indicated that water molecules adsorbed on Pt electrode in the double-layer regions through a low discharge quomodo .The EQCM studies provided quantitative results of surface mass variation during water adsorption and oxidation,and have thrown new light in elucidating the structure of …

Study For The Cathodic Behavior Of Active Chlorine On 316l Ss Electrode Surface, Hui Yu, Ming-Xian Sun, Yan Ma, Xiao-Bin Wang

Journal of Electrochemistry

The cathodic reducing reactions of active chlorine on 316 L SS electrode surface have been investigated by electrochemical techniques. The open circuit potential shifted positively and the limited diffusion current density increased significantly with the increasing content of active chlorine in the 3.5% sodium chloride solution. The two cathodic reduction processes of HClO and ClO^- exhibited on the surface of electrode with the active chlorine added to the 3.5%sodium chloride solution and the corresponding potentials of the two reducing reactions were confirmed. The linear relationship of the mass transport-limited Faradaic current, Id vs. the square root of the angular …

Investigations Of Smooth Function Of Polyethylene Glycol Surfactants On The Electrolessly Deposited Silver Film, Hao Tong, Zhi-Qing Qiao, Fen-Ning Jing, Meng-Ke Li, Chun-Ming Wang

Journal of Electrochemistry

Some non-ionic surfactants of Polyethylene Glycol 2000, 6000 and 20000 were used to estimate the smooth affection on the electrolessly deposited silver film. The adsorption state of the surfactants about Si/solution interface was investigated by using open circuit potential-time technology (Opt). As comparative experiments, the atomic force microscopy (AFM) was also performed to study the surface smooth effection of the surfactants. It was found that with the increasing of the carbon chain in the surfactants, the smooth effection is getting great. PEG 20000 showed the best smooth function.

Electroreduction Of Cd(Ⅱ) In Dmso And Complexation Of Cd(Ⅱ) With Coumarin Derivates, Ji-Guo Song, Hua-Can Song, Qi-Qin Yang, Yi-Wen Chen, Zun-Le Xu

Journal of Electrochemistry

Cadmium p-toluenesulfonate was synthesized and tested electrochemically for the first time. This salt can lose all the hydrated water easily and the dehydrated salt do not deliquesce in the air.Hence,the cadmium p-toluenesulfonate is suitable for the electrochemical studies in organic solvents.When the Cd(Ⅱ) reduced on Pt electrode in Cd(p-CH₃C₆H₄SO₃)₂+TBAP+DMSO, underpotential deposition of cadmium occurred at first, and then cadmium deposited. 4-Methyl-7-hydroxylcoumarin and 3-aminocoumarin coordinate with Cd(Ⅱ) respectively, as a result the reductive potentials of Cd(Ⅱ) moved to the negative direction.

Behaviors Of Fe-Cr Alloys During Cavitation Damage, Xia Bai, Dong-Bai Sun, Hong-Ying Yu, Hui-Ming Meng, Hui-Qin Li, Zi-Shuang Fan

Journal of Electrochemistry

The influence of the surface galvanic effect on the behaviors of three Fe-Cr alloys during cavitation damage in NaCl solutions have been investigated. The results showed that the galvanic effect caused by the inhomogeneity between the undamaged surface of the alloy and the damaged one will be enhanced by the area ratio of the undamaged and the damaged. The behaviors of alloys during cavitation are closely related to both their mechanical performance and anti-corrosion capabilities.

Study On The Corrosion & Electrochemical Properties Of Alloy Aa5083 And The Effect Of Active Chlorine In Seawater, Hong-Ren Wang, Jian-Hua Wu, Jun-Tao Wang, Hong-Bin Wang, Zhi-Gang Fang

Journal of Electrochemistry

In this paper potentiodynamic technique, cyclic polarization technique and immersion corrosion method were used to study the corrosion and electrochemical properties of AA5083 alloy in quiescent seawater, the effect of active chlorine on its properties was also studied. The results obtained indicate that the active chlorine has no remarkable impact on the corrosion and electrochemical properties of AA5083 alloy in area of design concentration which range from 0.2 to 0.5 mg/L, and it has favorable influence on the improvement of pitting corrosion resistance. While the pH value of seawater has evident influence on the corrosion resistance of AA5083 alloy.

Synthesis By Complexation Processes And Characterization Of Lini0.8Co0.2O2 Cathode Materials, Jing Liu, Zhao-Yin Wen, Zhong-Hua Gu, Xiu-Jian Zhu, Zu-Xiang Lin

Journal of Electrochemistry

The layered LiNi_0.8Co_0.2O₂ compound, which has been of great interest for lithium ion batteries, was prepared at low temperatures by calcining a complex precursor at different temperatures. The physical properties of the synthesized cathode materials were discussed in the light of structural (XRD). The charge and discharge cycling of the cells containing the synthesized oxide as the positive electrode in conjunction with lithium metals and employing a non-aqueous electrolyte showed that LiNi_0.8Co_0.2O₂ treated at 900 ℃ exhibited excellent performances. The first discharge capacity of LLiNi_0.8Co_0.2O_{2 …}

Fabrication Of SncuX/Cms Composite Materials For Lithium-Ion Batteries, Yu Liu, Jing-Ying Xie, Jun Yang, Ke Wang, Bao-Feng Wang

Journal of Electrochemistry

The composite material were prepared by sub-ctrochemical cycling tests showed that coulombic efficiency of the electrodes prepared by the composite materials was near 100 % after second cycle and the capacity dropped less than 5% after the 30th cycle, versus 390 mAh⋅g^-1 special capacity, improving 26% special capacity of pure CMS electrode. The electrochemical performance of the composite materials is depended strongly on the alloy content in the composite, the addhesive strength between alloy particles and CMS matrix, the distribution of particles on the surface of CMS and the particle size of alloy. The composite material can be applied …

The Electrochemical Performance Studies On Novel Lifepo4 Cathode Materials For Li-Ion Batteries, Zhi-Cong Shi, Chen Li, Yong Yang

Journal of Electrochemistry

The cathode materials of LiFePO₄ and  LiFePO₄ coated with carbon were synthesized by means of solid state reaction and ballmilling. The samples were characterized by X-ray diffraction, scanning electron microscopy, gas-phase element analysis and titration analysis methods. Electrochemical tests of two kinds of materials showed that both of them exhibit a 3.4V discharge voltage plateau, however, the coated samples demonstrated the improved performance in terms of discharge capacity and cyclic stability.

The Study On The Synthesis And Electrochemical Property Of K2Feo4, Yong-Long Wang, Ning Zhou, Shi-Hai Ye, Xue-Ping Gao, Feng Wu, Zuo-Xiang Zhou, De-Ying Song

Journal of Electrochemistry

The synthesis,characterization and electrochemical property of K₂FeO₄ for positive materal of lithium ion battery were studied. K₂FeO₄ with low purity was gained through the reaction of KCIO and Fe(NO₃)₃ in KOH solution and after recrystalization the purity of K₂FeO₄ reached 97%～98%. The methods of XRD and FTIR were used to measure the structure of K₂FeO₄ and its initial discharge performance was tested.

Development And Study Of The (Ag)-Ni/Cr Composite Plating With Antibacterial Properties And Corrosion Resistance, Ya-Ping Zhao, Jin-Hua Wang, Ren-He Yin, Jin Zheng, Le-Shu Yu

Journal of Electrochemistry

The 3-factor and 3-level orthogonal experiment was designed and through the comparison of the different films' antibacterial properties measured by bacterial colony counting and the corrosion resistance studied with the AC impedance method. The optimal plating conditions of the (Ag)-Ni/Cr composite plating, a novel functional plating, were determined. The results have indicated that the (Ag)-Ni/Cr composite plating is characterized by both antibacterial and corrosion resisting properties and has its wide applied prospect.

Pure Iron Electrolyzed From Scrap Iron Chips And Its Corrosion Characteristics, Wei-Min Cao, Ren-He Yin, Hui-Ceng Yan, Zhi-Qiang Ye

Journal of Electrochemistry

The high purity electrolytic iron was made from scrap iron chips. Electrolytic conditions of pure iron were determined in chloride baths and the highest purity was 99.983% by chemical analysis. Pure iron had very compact texture and high mechanical strength by SEM figures of cross section. In deaerated 0.5 kmol·m^-3 H₂SO₄ and 0.5 kmol·m^-3 NaCl solutions, the corrosion rate of iron decreased with increasing purity.

Fenton Reagent Produced In Electrolysis Cell And Its Using In Degradation And Decolourization Of Dye, Xi Zheng, Ri-Yao Chen, Rui-Fang Lan, Xiao Chen, Zhen Chen

Journal of Electrochemistry

The electro-chemical processing to produce Fenton reagent has been described. Fenton reagent having a high redox potential has been used as an oxidant in treatment of dye wastewater. Results show that both of the degradation and decolourization of dyes are efficient. The decolourization of dye wastewater reaches 100%.The COD removing rate is about 80%.

Experimental Investigation Of Steel Corrosion In Lead Bismuth Eutectic (Lbe): Characterization, Species Identification, And Chemical Reactions, John Farley, Dale L. Perry, Allen L. Johnson

Transmutation Sciences Materials (TRP)

The goal of the present research is to achieve a basic understanding of corrosion of steels by Lead Bismuth Eutectic (LBE). Liquid LBE is under consideration in the transmuter as both a spallation target and as a blanket coolant. There have been previous studies of LBE, especially by the Russians, who have over 80 reactor-years experience with LBE coolant in their Alpha-class submarine reactors. The Russians found that the presence of small amounts (ppm) of oxygen in the LBE significantly reduced corrosion. However, a fundamental understanding and verification of its role in the corrosion of steels is still very incomplete. …

Particle Growth In Urban And Industrial Plumes In Texas, Charles A. Brock, Michael Trainer, Thomas B. Ryerson, J. Andrew Neuman, David D. Parrish, John S. Holloway, Dennis K. Nicks, Gregory J. Frost, Gerhard Hübler, Fred C. Fehsenfeld, J. Charles Wilson, J. Michael Reeves, Bernard G. Lafleur, Henrike Hilbert, Elliot L. Atlas, Stephen G. Donnelly Ph.D., Sue M. Schauffler, Verity R. Stroud, Christine Wiedinmyer

Chemistry Faculty Publications

Particle size distributions and gas-phase particle precursors and tracer species were measured aboard an aircraft in the plumes downwind from industrial and urban sources in the vicinity of Houston, TX during the daytime in late August and early September 2000. Plumes originating from the Parish gas-fired and coal-fired power plant, petrochemical industries along the Houston ship channel, the petrochemical facilities near the Gulf coast, and the urban center of Houston were studied. Most of the particle mass flux advected downwind of Houston came from the industries and electrical utilities at the periphery of the city rather than from sources in …

Development Of A Systems Engineering Model Of The Chemical Separations Process: Quarterly Progress Report 11/16/02- 2/15/03, Yitung Chen, Randy Clarksean, Darrell Pepper

Separations Campaign (TRP)

Two activities are proposed in this Phase I task: the development of a systems engineering model and the refinement of the Argonne code AMUSE (Argonne Model for Universal Solvent Extraction). The detailed systems engineering model is the start of an integrated approach to the analysis of the materials separations associated with the TRP Program. A second portion of the project is to streamline and improve an integral part of the overall systems model, which is the software package AMUSE. AMUSE analyzes the UREX process and other related solvent extraction processes and defines many of the process streams that are integral …

Corrosion Of Steel By Lead Bismuth Eutectic: Quarterly Report November- December 2002 January 2003, John Farley

Transmutation Sciences Materials (TRP)

We continue to get valuable data from sputter depth profiling of steel samples. We meet weekly to discuss progress. We took depth-profiling data on D9 steel that had been exposed to LBE. This the first time we have examined this type of steel. This is important because it will enable us to separate out two effects and determine their effect on corrosion: composition of the steel vs surface preparation.

We started to plan a small experiments using a crucible of heated LBE, with the research program to be conducted at UNLV, on basic aspects of corrosion in this system. The …

On-Road Remote Sensing Of Automobile Emissions In The Labrea Area: Year 2, Mitchell J. Williams, Gary A. Bishop, Donald H. Stedman

Fuel Efficiency Automobile Test Publications

No abstract provided.

Development Of A Systems Engineering Model Of The Chemical Separations Process, Lijian Sun, Haritha Royyuru, Yitung Chen, Randy Clarksean, Darrell Pepper, George Vandegrift, James Laidler

Separations Campaign (TRP)

Project Overview:

• Two Components

– Refine AMUSE Code

– Develop Systems Engineering Model

• Research Objectives

– Develop a framework and environment for a systems engineering analysis of the chemical separations system for the AAA program.

– Establish a baseline systems engineering model from which modifications and improvements can be made.

– Refine the existing AMUSE program that gives a detailed examination of the UREX process, a critical component of the overall separation scheme.

Calibration Of Ysz Sensors For The Measurement Of Oxygen Concentration In Liquid Pb-Bi Eutectic, Xiaolong Wu, Ramkumar Sivaraman, Ning Li, Wei Hang, T. W. Darling, Yingtao Jiang, Woosoon Yim, Bingmei Fu

Transmutation Sciences Materials (TRP)

Although liquid lead-bismuth eutectic (LBE) is a good candidate for coolant in the subcritical transmutation blanket, it is known to be corrosive to stainless steel, the material of the carrying tubes and containers. Such longterm corrosion problem can be prevented by producing and maintaining a protective oxide layer on the exposed surface of stainless steel. For this purpose, it is required to accurately control the concentration of oxygen dissolved in LBE. Currently, YSZ (Yttria Stabilized Zirconia) oxygen sensors, based on an existing automotive oxygen sensor, with molten bismuth saturated with oxygen as the reference, have been selected for oxygen-concentration measurement. …

Tetratricopeptide Repeat Motif-Mediated Hsc70-Msti1 Interaction Molecular Characterization Of The Critical Contacts For Successful Binding And Specificity*, Odutayo O. Odunuge, Judith A. Hornby, Chrisiane Bies, Richard Zimmermann, David J. Pugh, Gregory L. Blatch

Faculty Publications

Murine stress-inducible protein 1 (mSTI1) is a cochaperone that is homologous with the human Hsp70/ Hsp90-organizing protein (Hop). Guided by Hop structural data and sequence alignment analyses, we have used site-directed mutagenesis, co-precipitation assays, circular dichroism spectroscopy, steady-state fluorescence, and surface plasmon resonance spectroscopy to both qualitatively and quantitatively characterize the contacts necessary for the N-terminal tetratricopeptide repeat domain (TPR1) of mSTI1 to bind to heat shock cognate protein 70 (Hsc70) and to discriminate between Hsc70 and Hsp90. We have shown that substitutions in the first TPR motif of Lys8 or Asn12 did not affect binding of mSTI1 to Hsc70, …

Oligothiophenes And Synthesis Thereof, Andrzej Rajca

Department of Chemistry: Faculty Publications

Novel oligothiophenes and intermediates therefor are disclosed together with a process for synthesizing them. The oligothiophenes are in the form of a helix which contains five-membered rings unsaturated heterocycles that are cross-conjugated and annelated into a helix.

Ft-Ir Studies Of Stereo Regular Pmma On Silica: Drying Effects, Bing Zhang, Suntree Kulkeratiyut, Suriyaphongse Kulkeratiyut, Frank D. Blum

Chemistry Faculty Research & Creative Works

A great amount of work has been done on the configuration of surface adsorbed poly(methyl methacrylate) (PMMA), especially on surfaces to which they have a strong attraction. Some studies have been make on the relationships between configuration and tacticity, molecular weight, adsorbed amount, and density of surface hydroxyl groups. The effect of tacticity on the conformation of alumina-adsorbed PMMA in solution and dry spin-coated films were studied by Grohen et al. Their results showed that surface-adsorbed PMMA chains adopted a relatively flat configuration, but iso-PMMA (isotactic) adsorbed on aluminum, with a much larger fraction of the bound carbonyl groups, had …

Quantitative Analysis Of Diepoxybutane Damage Within The Chicken Β-Globin Domain, André M. Pilon

Honors Theses

In industrial polymer and synthetic rubber production facilities, workers are exposed to 1,3-butadiene. This compound is converted in vivo to 1,2,3,4-diepoxybutane (DEB) and has been linked to increased incidences of cancer in these individuals. Carcinogenesis has been attributed to formation of DEB induced DNA interstrand cross-links. Previous studies have demonstrated that DEB cross-links deoxyguanosine residues within 5'-GNC sequences in synthetic DNA, in restriction fragments, and in defined sequence nucleosomes. The current study utilized the polymerase chain reaction (PCR) to examine DEB damage frequencies within nuclear genes, found within "open" regions of chromatin, as compared to regions of unexpressed sequence that …

Chlorobenzenes And Chloronitrobenzenes Interaction With Iron (O), Manuel Alejandro Serratos

Masters Theses

Degradation of chlorobenzene, dichlorobenzenes and chloronitrobenzenes (ClB, x-Cl2B and x-ClNO2B) was tested by trying to make them react with metallic iron, Fe (0), in water solvent.

The experiments consisted of optimizing the parameters of the reactions (like minimum mass of iron needed) and analytical detection conditions. Analytical techniques used were gas and liquid chromatography (GC and HPLC), mass spectrometry (MS) and UV-Vis spectroscopy.

No substances other than the initial ClB and x-Cl2B were detected in their tests with Fe (0) after shaking for periods of up to three days, although 10%weight average decreases in concentration were observed.

The ClNO2B isomers …

Phosphido-Bridged Complexes Linked By Unsaturated Phosphines, Yong Liu

Masters Theses

Di(p-tol)phosphido-bridged complexes, (OC)₄M[μ-P(p-tol)₂]₂M(CO)₄ (M = Mo, W), have been synthesized for the first time. These have been obtained from the reaction of (OC)₅MP(p-tol)₂H with BuLi, followed by air oxidation. The choice of solvent is very important as the intermediate anion, [(OC)₅MP(p-tol)₂] is unstable in THF. An ideal solvent for these preparations is CH₃OCH₂CH₂OCH₃ (monoglyme) from which yields of 68% and 76% were realized for the tungsten and molybdenum complexes, respectively. …