Physical Sciences and Mathematics Commons^™

High Performance Pure Sulfur Honeycomb-Like Architectures Synthesized By A Cooperative Self-Assembly Strategy For Lithium Sulfur Batteries, Xin Liang, Mohammad Kaiser, Konstantin Konstantinov, Richard Tandiono, Zhaoxiang Prof Zhaoxiang Wang, Hua-Kun Liu, S X. Dou, Jiazhao Wang

Shi Xue Dou

Honeycomb-like pure sulfur architectures were synthesized by a cooperative self-assembly strategy, in which a soft template is used to form the porous structure. Their electrochemical performance is significantly improved comparing with the commercial sulfur powder and the as-prepared sulfur without honeycomb morphology. There has been no report on using a soft template to prepare honeycomb-like sulfur particles.

Thermoelectric Performance Of N-Type (Pbte)0.75(Pbs)0.15(Pbse)0.1 Composites, Sima Aminorroaya Yamini, Heng Wang, Dianta Ginting, David R. G Mitchell, S X. Dou, G. Jeffrey Snyder

Shi Xue Dou

Lead chalcogenides (PbQ, Q = Te, Se, S) have proved to possess high thermoelectric efficiency for both n-type and p-type compounds. Recent success in tuning of electronic band structure, including manipulating the band gap, multiple bands, or introducing resonant states, has led to a significant improvement in the thermoelectric performance of p-type lead chalcogenides compared to the n-type ones. Here, the n-type quaternary composites of (PbTe)0.75(PbS)0.15(PbSe)0.1 are studied to evaluate the effects of nanostructuring on lattice thermal conductivity, carrier mobility, and effective mass variation. The results are compared with the similar ternary systems of (PbTe)1-x(PbSe)x, (PbSe) 1-x(PbS)x, and (PbS)1-x(PbTe)x. The …

Thermoelectric Performance Of Tellurium-Reduced Quaternary P-Type Lead-Chalcogenide Composites, Sima Aminorroaya Yamini, Heng Wang, Zachary M. Gibbs, Yanzhong Pei, David R. G Mitchell, S X. Dou, G. Jeffrey Snyder

Shi Xue Dou

A long-standing technological challenge to the widespread application of thermoelectric generators is obtaining high-performance thermoelectric materials from abundant elements. Intensive study on PbTe alloys has resulted in a high figure of merit for the single-phase ternary PbTe-PbSe system through band structure engineering, and the low thermal conductivity achieved due to nanostructuring leads to high thermoelectric performance for ternary PbTe-PbS compounds. Recently, the single-phase p-type quaternary PbTe-PbSe-PbS alloys have been shown to provide thermoelectric performance superior to the binary and ternary lead chalcogenides. This occurs via tuning of the band structure and from an extraordinary low thermal conductivity resulting from high-contrast …

High-Performance Sodium-Ion Batteries And Sodium-Ion Pseudocapacitors Based On Mos2/Graphene Composites, Yunxiao Wang, Shulei Chou, David Wexler, Hua-Kun Liu, S X. Dou

Shi Xue Dou

Sodium-ion energy storage, including sodium-ion batteries (NIBs) and electrochemical capacitive storage (NICs), is considered as a promising alternative to lithium-ion energy storage. It is an intriguing prospect, especially for large-scale applications, owing to its low cost and abundance. MoS2 sodiation/desodiation with Na ions is based on the conversion reaction, which is not only able to deliver higher capacity than the intercalation reaction, but can also be applied in capacitive storage owing to its typically sloping charge/discharge curves. Here, NIBs and NICs based on a graphene composite (MoS2/G) were constructed. The enlarged d-spacing, a contribution of the graphene matrix, and the …

Ultra-High Performance, High-Temperature Superconducting Wires Via Cost-Effective, Scalable, Co-Evaporation Process, Ho-Sup Kim, Sang-Soo Oh, Hong-Soo Ha, Dojun Youm, Seung-Hyun Moon, Jung Ho Kim, S X. Dou, Yoon-Uk Heo, Sung-Hun Wee, Amit Goyal

Shi Xue Dou

Long-length, high-temperature superconducting (HTS) wires capable of carrying high critical current, Ic, are required for a wide range of applications. Here, we report extremely high performance HTS wires based on 5 μm thick SmBa2Cu3O7 − δ (SmBCO) single layer films on textured metallic templates. SmBCO layer wires over 20 meters long were deposited by a cost-effective, scalable co-evaporation process using a batch-type drum in a dual chamber. All deposition parameters influencing the composition, phase, and texture of the films were optimized via a unique combinatorial method that is broadly applicable for co-evaporation of other promising complex materials containing several cations. …

Reliable And Efficient Multithreading, Tongping Liu

Doctoral Dissertations

The advent of multicore architecture has increased the demand for multithreaded programs. It is notoriously far more challenging to write parallel programs correctly and efficiently than sequential ones because of the wide range of concurrency errors and performance problems. In this thesis, I developed a series of runtime systems and tools to combat concurrency errors and performance problems of multithreaded programs. The first system, Dthreads, automatically ensures determinism for unmodified C/C++ applications using the pthreads library without requiring programmer intervention and hardware support. Dthreads greatly simplifies the understanding and debugging of multithreaded programs. Dthreads often matches or even exceeds the …

A Comparative Study Of Accuracy And Performance Between A Fully 2d Gpu Based And A 1d-2d Coupled Numerical Model In A Real River, Mario Morales-Hernández, Asier Lacasta, Javier Murillo, Pilar Brufau, Pilar García-Navarro

International Conference on Hydroinformatics

Hydraulic simulation is becoming a very widely used tool to provide information about the duration, the extension and the magnitude of a flooding episode. In the last decade, the advances in the numerical schemes, connected to the evolution experimented in the power of computers have allowed to aim for maximum accuracy in the results instead of working with simplified models. In particular, two main implementations have been extensively developed in the recent years: 1D-2D coupled numerical models and fully 2D models under GPU technologies. These strategies allow to simulate a wide range of applications over large domains and time scale …

A Management Indicator Program For Water Operating Agencies, Martha Patricia Hansen Rodríguez, Víctor Hugo Alcocer Yamanaka, Yenni Laurel Varela

International Conference on Hydroinformatics

The management indicator program for operating agencies (PIGOO, for its initials in Spanish) specifies a set of 28 management indicators that help to measure the operational aspects, financial aspects and efficiencies of potable water supply systems. Ideally, the performance indicators of an operating agency should be linked to an objective or strategy established by that same agency. The performance indicators are calculated based on annual data, variables such as the volume of water produced, the number of employees, total income and expenditures, rate of leaks and claims. The Mexican Institute of Water Technology has conducted PIGOO since 2005. From 2005 …

A Hamming Embedding Kernel With Informative Bag-Of-Visual Words For Video Semantic Indexing, Feng Wang, Wen-Lei Zhao, Chong-Wah Ngo, Bernard Merialdo

Research Collection School Of Computing and Information Systems

In this article, we propose a novel Hamming embedding kernel with informative bag-of-visual words to address two main problems existing in traditional BoW approaches for video semantic indexing. First, Hamming embedding is employed to alleviate the information loss caused by SIFT quantization. The Hamming distances between keypoints in the same cell are calculated and integrated into the SVM kernel to better discriminate different image samples. Second, to highlight the concept-specific visual information, we propose to weight the visual words according to their informativeness for detecting specific concepts. We show that our proposed kernels can significantly improve the performance of concept …

Aqueous Dispersions Of Reduced Graphene Oxide And Multi Wall Carbon Nanotubes For Enhanced Glucose Oxidase Bioelectrode Performance, Willo Grosse, Joffrey Champavert, Sanjeev Gambhir, Gordon G. Wallace, Simon E. Moulton

Gordon Wallace

Aqueous dispersions of reduced graphene oxide (rGO) and multi walled carbon nanotubes (MWCNT) were fabricated through a modified chemical reduction method. The significant advantage of the method developed here is the omission of any stabilising compound or organic solvent to obtain stable rGO-MWCNT dispersions. Significantly biological entities, in this case the enzyme glucose oxidase (GOx), can be successfully incorporated into the dispersion. These dispersions were characterised using XPS, SEM, zeta potential and particle size measurements which showed that the dispersion stability is not sacrificed with the addition of GOx, and significantly, the electrical properties of the rGO and MWCNTs are …

Evaluation Of Encapsulating Coatings On The Performance Of Polypyrrole Actuators, Sina Naficy, Nicholas Stoboi, Philip G. Whitten, Geoffrey M. Spinks, Gordon G. Wallace

Gordon Wallace

Conjugated polymer actuators are electroactive materials capable of generating force and movement in response to an applied external voltage. Many potential biomedical and industrial applications require these actuators to operate in a liquid environment. However, immersion of uncoated conducting polymer actuators in non-electrolyte liquids greatly reduces their operating lifetime. Here, we demonstrate the use of spray coating as an effective and simple method to encapsulate polypyrrole (PPy) tri-layer bending actuators. Poly(styrene-b-isobutylene-b-styrene) (SIBS) was used as an encapsulating, compliant spray coating on PPy actuators. A significant enhancement in actuator lifetime in both air and water was observed by encapsulating the actuators. …

Cation Exchange At Semiconducting Oxide Surfaces: Origin Of Light-Induced Performance Increases In Porphyrin Dye-Sensitized Solar Cells, Matthew J. Griffith, Kenji Sunahara, Akihiro Furube, Attila J. Mozer, David L. Officer, Pawel Wagner, Gordon G. Wallace, Shogo Mori

Gordon Wallace

The origin of simultaneous improvements in the short-circuit current density (Jsc) and open-circuit voltage (Voc) of porphyrin dye-sensitized TiO2 solar cells following white light illumination was studied by systematic variation of several different device parameters. Reduction of the dye surface loading resulted in greater relative performance enhancements, suggesting open space at the TiO2 surface expedites the process. Variation of the electrolyte composition and subsequent analysis of the conduction band potential shifts suggested that a light-induced replacement of surface-adsorbed lithium (Li+) ions with dimethylpropylimidazolium (DMPIm+) ions was responsible for an increased electron lifetime by decreasing the recombination with the redox mediator. …

A Facile Route To Synthesize Transition Metal Oxide/Reduced Graphene Oxide Composites And Their Lithium Storage Performance, Chongjun Zhao, Shulei Chou, Yunxiao Wang, Cuifeng Zhou, Hua-Kun Liu, S X. Dou

Shi Xue Dou

Transition metal oxide (Mn3O4, Fe2O3, Co3O4, and ZnO) and reduced graphene oxide (RGO) composites were successfully synthesized via a hydrothermal method using the direct reaction between the corresponding metal powder and graphene oxide (GO). In this process, the GO can be reduced by transition metal powder in water, and the nanosized metal oxide can be obtained, and homogeneously mixed with and wrapped by RGO to form a metal oxide/RGO composite at the same time. X-ray diffraction, Raman spectroscopy, X-ray photoelectron spectroscopy, and scanning and transmission electron microscopy were used to characterize the as-prepared materials. The different experimental parameters, including reactants, …

Synergetic Combination Of Limd With Chpd For The Production Of Economical And High Performance Mgb2 Wires, Minoru Maeda, Md Shahriar Ai Hossain, Ashkan Motaman, Jung Ho Kim, Anna Kario, Matt Rindfleisch, Mike Tomsic, S X. Dou

Shi Xue Dou

We propose an economical fabrication concept, the localized internal magnesium diffusion (IMD) method. Instead of using a single magnesium (Mg) rod in the center of a metal sheath tube, we use large-sized Mg particles (20-50 mesh) mixed well with cheap 97% crystalline boron powder to fill the metal sheath tube. After a repeated drawing process, the coarse Mg is elongated along the core wire axis of the metal sheath tube. Textured MgB2 grains are then formed during the sintering process. In the localized IMD process, however, there is still a need to improve the overall density. In order to increase …

Indemics: An Interactive High-Performance Computing Framework For Data Intensive Epidemic Modeling, Keith R. Bisset, Jiangzhuo Chen, Suruchi Deodhar, Xizhou Feng, Yifei Ma, Madhav V. Marathe

Mathematics, Statistics and Computer Science Faculty Research and Publications

We describe the design and prototype implementation of Indemics (_Interactive; Epi_demic; _Simulation;)—a modeling environment utilizing high-performance computing technologies for supporting complex epidemic simulations. Indemics can support policy analysts and epidemiologists interested in planning and control of pandemics. Indemics goes beyond traditional epidemic simulations by providing a simple and powerful way to represent and analyze policy-based as well as individual-based adaptive interventions. Users can also stop the simulation at any point, assess the state of the simulated system, and add additional interventions. Indemics is available to end-users via a web-based interface.

Detailed performance analysis shows that Indemics greatly enhances the …

High-Performance Sodium-Ion Batteries And Sodium-Ion Pseudocapacitors Based On Mos2/Graphene Composites, Yunxiao Wang, Shulei Chou, David Wexler, Hua-Kun Liu, S X. Dou

Australian Institute for Innovative Materials - Papers

Sodium-ion energy storage, including sodium-ion batteries (NIBs) and electrochemical capacitive storage (NICs), is considered as a promising alternative to lithium-ion energy storage. It is an intriguing prospect, especially for large-scale applications, owing to its low cost and abundance. MoS2 sodiation/desodiation with Na ions is based on the conversion reaction, which is not only able to deliver higher capacity than the intercalation reaction, but can also be applied in capacitive storage owing to its typically sloping charge/discharge curves. Here, NIBs and NICs based on a graphene composite (MoS2/G) were constructed. The enlarged d-spacing, a contribution of the graphene matrix, and the …

Enhanced Sodium-Ion Battery Performance By Structural Phase Transition From Two-Dimensional Hexagonal-Sns2 To Orthorhombic-Sns, Tengfei Zhou, Wei Kong Pang, Chaofeng Zhang, Jianping Yang, Zhixin Chen, Hua-Kun Liu, Zaiping Guo

Australian Institute for Innovative Materials - Papers

Structural phase transitions can be used to alter the properties of a material without adding any additional elements and are therefore of significant technological value. It was found that the hexagonal-SnS2 phase can be transformed into the orthorhombic-SnS phase after an annealing step in an argon atmosphere, and the thus transformed SnS shows enhanced sodium-ion storage performance over that of the SnS2, which is attributed to its structural advantages. Here, we provide the first report on a SnS@graphene architecture for application as a sodium-ion battery anode, which is built from two-dimensional SnS and graphene nanosheets as complementary building blocks. The …

Thermoelectric Performance Of N-Type (Pbte)0.75(Pbs)0.15(Pbse)0.1 Composites, Sima Aminorroaya Yamini, Heng Wang, Dianta Ginting, David R. G Mitchell, S X. Dou, G. Jeffrey Snyder

Australian Institute for Innovative Materials - Papers

Lead chalcogenides (PbQ, Q = Te, Se, S) have proved to possess high thermoelectric efficiency for both n-type and p-type compounds. Recent success in tuning of electronic band structure, including manipulating the band gap, multiple bands, or introducing resonant states, has led to a significant improvement in the thermoelectric performance of p-type lead chalcogenides compared to the n-type ones. Here, the n-type quaternary composites of (PbTe)0.75(PbS)0.15(PbSe)0.1 are studied to evaluate the effects of nanostructuring on lattice thermal conductivity, carrier mobility, and effective mass variation. The results are compared with the similar ternary systems of (PbTe)1-x(PbSe)x, (PbSe) 1-x(PbS)x, and (PbS)1-x(PbTe)x. The …

Thermoelectric Performance Of Tellurium-Reduced Quaternary P-Type Lead-Chalcogenide Composites, Sima Aminorroaya Yamini, Heng Wang, Zachary M. Gibbs, Yanzhong Pei, David R. G Mitchell, S X. Dou, G. Jeffrey Snyder

Australian Institute for Innovative Materials - Papers

A long-standing technological challenge to the widespread application of thermoelectric generators is obtaining high-performance thermoelectric materials from abundant elements. Intensive study on PbTe alloys has resulted in a high figure of merit for the single-phase ternary PbTe-PbSe system through band structure engineering, and the low thermal conductivity achieved due to nanostructuring leads to high thermoelectric performance for ternary PbTe-PbS compounds. Recently, the single-phase p-type quaternary PbTe-PbSe-PbS alloys have been shown to provide thermoelectric performance superior to the binary and ternary lead chalcogenides. This occurs via tuning of the band structure and from an extraordinary low thermal conductivity resulting from high-contrast …

Hp-Daemon: HIgh PErformance DIstributed ADaptive ENergy-Efficient MAtrix-MultiplicatiOn, Li Tan, Longxiang Chen, Zizhong Chen, Ziliang Zong, Rong Ge, Dong Li

Mathematics, Statistics and Computer Science Faculty Research and Publications

The demands of improving energy efficiency for high performance scientific applications arise crucially nowadays. Software-controlled hardware solutions directed by Dynamic Voltage and Frequency Scaling (DVFS) have shown their effectiveness extensively. Although DVFS is beneficial to green computing, introducing DVFS itself can incur non-negligible overhead, if there exist a large number of frequency switches issued by DVFS. In this paper, we propose a strategy to achieve the optimal energy savings for distributed matrix multiplication via algorithmically trading more computation and communication at a time adaptively with user-specified memory costs for less DVFS switches, which saves 7.5% more energy on average than …

Star-Crossed Cube: An Alternative To Star Graph, Nibedita Adhikari, Chitta Ranjan Tripathy

Turkish Journal of Electrical Engineering and Computer Sciences

This paper introduces a new interconnection network topology called the star-crossed cube (SCQ). The SCQ is observed to be superior to other contemporary networks in terms of various topological parameters such as diameter, cost, average distance, and message traffic density. The various performance metrics of the proposed network, including cost effectiveness and time-cost effectiveness, are found to be better. The optimal routing and broadcasting algorithms for the new network are also presented. Embedding properties for the proposed network are also studied.

Multi-Threaded Implementation Of Association Rule Mining With Visualization Of The Pattern Tree, Eera Gupta

LSU Master's Theses

Motor Vehicle fatalities per 100,000 population in the United States has been reported to be 10.69% in the year 2012 as per NHTSA (National Highway Traffic Safety Administration). The fatality rate has increased by 0.27% in 2012 compared to the rate in the year 2011. As per the reports, there are many factors involved in increasing the fatality rate drastically such as driving under influence, testing while driving, and various other weather phenomena. Decision makers need to analyze the factors attributing to the increase in an accident rate to take implied measures. Current methods used to perform the data analysis …

A Regression Model To Investigate The Performance Of Black-Scholes Using Macroeconomic Predictors, Timothy A. Smith, Ersoy Subasi, Aliraza M. Rattansi

Publications

As it is well known an option is defined as the right to buy sell a certain asset, thus, one can look at the purchase of an option as a bet on the financial instrument under consideration. Now while the evaluation of options is a completely different mathematical topic than the prediction of future stock prices, there is some relationship between the two. It is worthy to note that henceforth we will only consider options that have a given fixed expiration time T, i.e., we restrict the discussion to the so called European options. Now, for a simple illustration of …

Fabrication Of Graphene Foam Supported Carbon Nanotube/Polyaniline Hybrids For High-Performance Supercapacitor Applications, Hongxia Yang, Nan Wang, Qun Xu, Zhimin Chen, Yumei Ren, Joselito M. Razal, Jun Chen

Australian Institute for Innovative Materials - Papers

A large-scale, high-powered energy storage system is crucial for addressing the energy problem. The development of high-performance materials is a key issue in realizing the grid-scale applications of energy-storage devices. In this work, we describe a simple and scalable method for fabricating hybrids (graphenepyrrole/ carbon nanotube-polyaniline (GPCP)) using graphene foam as the supporting template. Graphene-pyrrole (G-Py) aerogels are prepared via a green hydrothermal route from two-dimensional materials such as graphene sheets, while a carbon nanotube/polyaniline (CNT/PANI) composite dispersion is obtained via the in situ polymerization method. The functional nanohybrid materials of GPCP can be assembled by simply dipping the prepared …

Mechanically Strong High Performance Layered Polypyrrole Nano Fibre/Graphene Film For Flexible Solid State Supercapacitor, Sha Li, Chen Zhao, Kewei Shu, Caiyun Wang, Zaiping Guo, Gordon G. Wallace, Hua-Kun Liu

Australian Institute for Innovative Materials - Papers

Paper like flexible electrode becomes one of the most important research objects recently in request of the fast expanding market of portable electronics. Flexible solid state supercapacitors are shortlisted as one of the most promising energy devices to power electronics with medium to high power density requirements. In this work, we developed a simple but effective way to produce a mechanically strong and electrochemically active RGO/polypyrrole (PPy) fibre paper. A well-bedded microstructure was created with interlaced polypyrrole fibres evenly distributed between the graphene layers. Such microstructure can create enormous amount of pores and therefore provides larger interfaces for charge carrier …

Sulfur-Graphene Nanostructured Cathodes Via Ball-Milling For High-Performance Lithium-Sulfur Batteries, Jiantie Xu, Jianglan Shui, Jianli Wang, Min Wang, Hua-Kun Liu, S X. Dou, In-Yup Jeon, Jeong-Min Seo, Jong-Beom Baek, Liming Dai

Australian Institute for Innovative Materials - Papers

Although much progress has been made to develop high-performance lithium-sulfur batteries (LSBs), the reported physical or chemical routes to sulfur cathode materials are often multistep/complex and even involve environmentally hazardous reagents, and hence are infeasible for mass production. Here, we report a simple ball-milling technique to combine both the physical and chemical routes into a one-step process for low-cost, scalable, and eco-friendly production of graphene nanoplatelets (GnPs) edge-functionalized with sulfur (S-GnPs) as highly efficient LSB cathode materials of practical significance. LSBs based on the S-GnP cathode materials, produced by ball-milling 70 wt % sulfur and 30 wt % graphite, delivered …

Ultra-High Performance, High-Temperature Superconducting Wires Via Cost-Effective, Scalable, Co-Evaporation Process, Ho-Sup Kim, Sang-Soo Oh, Hong-Soo Ha, Dojun Youm, Seung-Hyun Moon, Jung Ho Kim, S X. Dou, Yoon-Uk Heo, Sung-Hun Wee, Amit Goyal

Australian Institute for Innovative Materials - Papers

Long-length, high-temperature superconducting (HTS) wires capable of carrying high critical current, Ic, are required for a wide range of applications. Here, we report extremely high performance HTS wires based on 5 μm thick SmBa2Cu3O7 − δ (SmBCO) single layer films on textured metallic templates. SmBCO layer wires over 20 meters long were deposited by a cost-effective, scalable co-evaporation process using a batch-type drum in a dual chamber. All deposition parameters influencing the composition, phase, and texture of the films were optimized via a unique combinatorial method that is broadly applicable for co-evaporation of other promising complex materials containing several cations. …

Performance Enhancement Of Single-Walled Nanotube-Microwave Exfoliated Graphene Oxide Composite Electrodes Using A Stacked Electrode Configuration, Dennis Antiohos, Mark S. Romano, Joselito M. Razal, Stephen Beirne, Phil Aitchison, Andrew I. Minett, Gordon G. Wallace, Jun Chen

Australian Institute for Innovative Materials - Papers

We report the development of a stacked electrode supercapacitor cell using stainless steel meshes as the current collectors and optimised single walled nanotubes (SWNT)-microwave exfoliated graphene oxide (mw rGO) composites as the electrode material. The introduction of mw rGO into a SWNT matrix creates an intertwined porous structure that enhances the electroactive surface area and capacitive performance due to the 3-D hierarchical structure that is formed. The composite structure was optimised by varying the weight ratio of the SWNTs and mw rGO. The best performing ratio was the 90% SWNT-10% mw rGO electrode which achieved a specific capacitance of 306 …

High Performance Pure Sulfur Honeycomb-Like Architectures Synthesized By A Cooperative Self-Assembly Strategy For Lithium Sulfur Batteries, Xin Liang, Mohammad Kaiser, Konstantin Konstantinov, Richard Tandiono, Zhaoxiang Prof Zhaoxiang Wang, Hua-Kun Liu, S X. Dou, Jiazhao Wang

Australian Institute for Innovative Materials - Papers

Honeycomb-like pure sulfur architectures were synthesized by a cooperative self-assembly strategy, in which a soft template is used to form the porous structure. Their electrochemical performance is significantly improved comparing with the commercial sulfur powder and the as-prepared sulfur without honeycomb morphology. There has been no report on using a soft template to prepare honeycomb-like sulfur particles.

Enhanced Performance Of Dye-Sensitized Solar Cells Using Carbazole-Substituted Di-Chromophoric Porphyrin Dyes, Long Zhao, Pawel Wagner, Anastasia Elliott, Matthew Griffith, Tracey M. Clarke, Keith C. Gordon, Shogo Mori, Attila Mozer

Australian Institute for Innovative Materials - Papers

The purpose of this work is to investigate the origin of improved photovoltaic performance of a series of di-chromophoric carbazole-substituted porphyrin dyes employed as sensitizers in dye-sensitized solar cells. Five di-chromophoric zinc porphyrin dyes with the same porphyrin core, a carbazole unit attached in the meso-position through a phenylethenyl linkage, and substituents spanning a range of electron affinities, in an attempt to tune the electronic level of the carbazole unit, have been synthesized (CZPs). Density functional theory (DFT) calculations predicted the nature of the electronic transitions observed in the CZP systems, showing a large degree of orbital mixing. In contrast, …