Physical Sciences and Mathematics Commons^™

A One-Dimensional Analysis Of A Microbial Fuel Cell For Efficient Acetate Removal And Power Density Output, David Rouhani

UNLV Theses, Dissertations, Professional Papers, and Capstones

Microbial fuel cells (MFCs) are electrochemical devices that utilize microorganisms to convert organic matter into electrical energy. MFCs have been discussed to have potential application for sustainable wastewater treatment due to their ability to generate electricity while simultaneously treating contaminated water. To optimize MFC performance, numerical models can be used to understand the complex electrochemical and biological processes occurring in the system. In this study, a numerical model was developed to simulate the performance of MFCs under varying operating conditions and to investigate the performance of a MFC for treating wastewater fuel. More specifically, the MFC was modeled to oxidize …

Metastability And Degradation In Cu(In,Ga)Se2 Thin-Film Solar Cells, Mohsen Jahandardoost

UNLV Theses, Dissertations, Professional Papers, and Capstones

Cu(In,Ga)(S,Se)2 or CIGS is a thin-film semiconductor that has shown a device efficiency of 23.35% and 24.2% for single-junction and perovskite/CIGS tandem solar cells, respectively. CIGS offers promising properties such as tunable bandgap and ease of processing making them great candidates for thin-film tandem devices. However, knowledge of the effect of material defects, buffer materials, and post-deposition treatment (PDT) on degradation and metastability behavior in these devices is not well understood.In this dissertation, metastability and long-term degradation of CIGS thin-film solar cells have been investigated under combinatorial stress factors of heat, light, and voltage bias to systematically understand the effect …

Radiomic Features To Predict Overall Survival Time For Patients With Glioblastoma Brain Tumors Based On Machine Learning And Deep Learning Methods, Lina Chato

UNLV Theses, Dissertations, Professional Papers, and Capstones

Machine Learning (ML) methods including Deep Learning (DL) Methods have been employed in the medical field to improve diagnosis process and patient’s prognosis outcomes. Glioblastoma multiforme is an extremely aggressive Glioma brain tumor that has a poor survival rate. Understanding the behavior of the Glioblastoma brain tumor is still uncertain and some factors are still unrecognized. In fact, the tumor behavior is important to decide a proper treatment plan and to improve a patient’s health. The aim of this dissertation is to develop a Computer-Aided-Diagnosis system (CADiag) based on ML/DL methods to automatically estimate the Overall Survival Time (OST) for …

Plasma Aerodynamics: Experimental Quantification Of The Lift Force Generated On An Airfoil Using Plasma Actuation To Estimate Power Requirements In Small Uav Applications, Getachew Ashenafi

UNLV Theses, Dissertations, Professional Papers, and Capstones

This research addressed the amount of electric power required to induce specific changes in lift force using a NACA 2127 airfoil with a chord length of ~28 mm, connected to a micro load cell, in a wind tunnel of 103 square centimeter cross-section. A DBD plasma actuator supplied by a ZVS driven high voltage pulsed DC circuit, operating at a frequency of 17.4 kHz, was utilized for voltages of up to 5000 V. Two configurations of electrode gapping were compared to determine the efficient use of power. The configuration with a gap of ~1 mm between the upstream and downstream …

A Hyperelastic Porous Media Framework For Ionic Polymer-Metal Composites And Characterization Of Transduction Phenomena Via Dimensional Analysis And Nonlinear Regression, Zakai J. Olsen

UNLV Theses, Dissertations, Professional Papers, and Capstones

Ionic polymer-metal composites (IPMC) are smart materials that exhibit large deformation in response to small applied voltages, and conversely generate detectable electrical signals in response to mechanical deformations. The study of IPMC materials is a rich field of research, and an interesting intersection of material science, electrochemistry, continuum mechanics, and thermodynamics. Due to their electromechanical and mechanoelectrical transduction capabilities, IPMCs find many applications in robotics, soft robotics, artificial muscles, and biomimetics. This study aims to investigate the dominating physical phenomena that underly the actuation and sensing behavior of IPMC materials. This analysis is made possible by developing a new, hyperelastic …

A Monolithic Arbitrary Lagrangian-Eulerian Finite Element Method For An Unsteady Stokes/Parabolic Interface Problem, Ian Kesler

UNLV Theses, Dissertations, Professional Papers, and Capstones

In this thesis, a non-conservative arbitrary Lagrangian-Eulerian (ALE) method is developed

and analyzed for a type of linearized Fluid-Structure Interaction (FSI) problem in a

time dependent domain with a moving interface - an unsteady Stokes/parabolic interface

problem with jump coefficients. The corresponding mixed finite element approximation is

analyzed for both semi- and full discretization based upon the so-called non-conservative

ALE scheme. The stability and optimal convergence properties in the energy norm are

obtained for both schemes.

The Affective Perceptual Model: Enhancing Communication Quality For Persons With Pimd, Jadin Tredup

UNLV Theses, Dissertations, Professional Papers, and Capstones

Methods for prolonged compassionate care for persons with Profound Intellectual and Multiple Disabilities (PIMD) require a rotating cast of import people in the subjects life in order to facilitate interaction with the external environment. As subjects continue to age, dependency on these people increases with complexity of communications while the quality of communication decreases. It is theorized that a machine learning (ML) system could replicate the attuning process and replace these people to promote independence. This thesis extends this idea to develop a conceptual and formal model and system prototype.

The main contributions of this thesis are: (1) proposal of …

Design And Preliminary Evaluation Of A Supercritical Carbon Dioxide Brayton Cycle For Solar Dish Concentrator Clean Energy Production, Danielle Nobles-Lookingbill

UNLV Theses, Dissertations, Professional Papers, and Capstones

As we move toward energy independence and more ambitious clean energy goals, solar energy research must push the efficiency limits of traditional energy generation systems. Increases in efficiency can be achieved by increasing the hot temperature of the power cycle. Recent research demonstrates the potential for increased efficiency and a vastly smaller component size when supercritical carbon dioxide Brayton power cycles are used. Concentrated solar and nuclear heat sources are capable of achieving the high working fluid temperatures needed for significant efficiency gains. This NSF EPSCoR funded, experimental research system is designed to exploit the uniquely immense solar irradiance of …

Design & Delivery Of Automated Winston-Lutz Test For Isocentric & Off-Axis Delivery Stability Utilizing Truebeam Developer Mode & Electronic Portal Imaging Device, Mahmoud Mohammad Yaqoub

UNLV Theses, Dissertations, Professional Papers, and Capstones

The uncertainties in treatment delivery cannot be ignored in radiation therapy. Thus, the quality assurance QA tests are very important task of the medical physicist in clinical practice. Assuring the coincidence between the mechanical isocenter of the Linear Accelerator (LINAC) and its radiation beams isocenter is one of the most important qualities need to be tested, and the Winston Lust (WL) test is the

most popular technique to perform this task, especially for the treatment modalities which need high precision in beam delivery such as the stereotactic radiosurgery/stereotactic body radiotherapy (SRS/SBRT). The linear accelerator-based SRS/SBRT is a well-established method in …

Fast Neutron Detection In Nuclear Material Photofission Assay Using A 15 Mev Linear Electron Accelerator, Matthew Steven Hodges

UNLV Theses, Dissertations, Professional Papers, and Capstones

The purpose of this research was to use a 15 MeV (K15 model by Varian) linear electron accelerator (linac) for the photon assay of special nuclear materials (SNM). First, the properties of the photon radiation probe were determined. The stochastic radiation transport code, MCNP5, was used to develop computational models for the linac. The spectral distribution of photons as well as dose rate contour maps of the UNLV accelerator facility were computed for several linac operating configurations. These computational models were validated through comparison with experimental measurements of dose rates.

The linac model was used to simulate the photon interrogation …

Stationary Nonimaging Concentrators – A Comprehensive Study And Design Improvements, Srikanth Madala

UNLV Theses, Dissertations, Professional Papers, and Capstones

Most places on our planet receive an annual average radiation between 800-1000 W/m2. In the man-made world, this radiation is largely incident on stationary structures such as buildings, roads, monuments, bridges etc. Moreover, in the natural world also, there are large tracts of barren land which can be put to good use given their solar energy potential. The vision of the current research is to concentrate all this available solar energy to a more readily usable form. Therefore, stationary nonimaging solar concentrator technologies are sought after. This dissertation work is an exhaustive research on the nonimaging concentrating mechanisms with stationary …

Ionic Polymer-Metal Composite Actuators Based On Nafion Blends With Functional Polymers, Jungsoo Nam

UNLV Theses, Dissertations, Professional Papers, and Capstones

Ionic polymer metal composites (IPMCs) have been an attractive research subject for use in underwater robotic applications, biomedical and biomimetic application owing to their great potential as actuators, artificial muscles, and more. IPMC is synthetic composite nanomaterial of ion exchange membranes and metal electrode. Although both components are important, the properties of ion exchange membranes should be emphasized since it is responsible of the path for the mobile ions to migrate when voltage is applied to exhibit deformation. Most of the researches that have been done on IPMCs used commercially available Nafion as their ion exchange membranes. However, its high …

Neutron-Gamma Discrimination In Elpasolite Scintillator Detector, Brittany Morgan

UNLV Theses, Dissertations, Professional Papers, and Capstones

Existing nuclear stockpiles and weapons-making capabilities imperil the global community. Current nonproliferation efforts involve the research and development of newer, more efficient detection systems that can be deployed for the interdiction and monitoring of special nuclear materials (SNM). Spontaneous and induced fission events in SNM produce neutrons and gamma rays, which can be detected and analyzed, in particular, using scintillator detectors. Various electronic data acquisition systems and data analysis methods have been employed to record and characterize neutron and photon signatures. The goal of this thesis is to develop a new method of discrimination between neutrons and photons in the …

On The Scattering Of An Acoustic Plane Wave By A Soft Prolate Spheroid, Joseph Michael Borromeo

UNLV Theses, Dissertations, Professional Papers, and Capstones

This thesis solves the scattering problem in which an acoustic plane wave of propagation number K1 is scattered by a soft prolate spheroid. The interior field of the scatterer is characterized by a propagation number K2, while the field radiated by the scatterer is characterized by the propagation number K3. The three fields and their normal derivatives satisfy boundary conditions at the surface of the scatterer. These boundary conditions involve six complex parameters depending on the propagation numbers. The scattered wave also satisfies the Sommerfeld radiation condition at infinity. Through analytical methods, series representations are constructed for the interior field …

Simulation Of An Air Cooled Single-Effect Solar Absorption Cooling System With Evacuated Tube Collectors, Mohsen Jahandardoost

UNLV Theses, Dissertations, Professional Papers, and Capstones

Consistently increasing CO2 emission and ozone depletion from synthetic refrigerants are serious environmental issues challenging the scientific community. Absorption cooling systems give scope of utilizing low grade energy source for generating cooling effect. Solar energy is one of these low grade energy sources and with considering the fact that cooling demand increases with the intensity of solar radiation, solar refrigeration has been considered as a logical solution.

This thesis consists of two different simulation stages, in the first stage, a single effect lithium bromide absorption cooling system with constant cooling capacity is modeled and the effect of ambient and generator …

Designing, Building And Testing A Solar Thermoelectric Generation, Steg, For Energy Delivery To Remote Residential Areas In Developing Regions, Yacouba Moumouni

UNLV Theses, Dissertations, Professional Papers, and Capstones

New alternatives and inventive renewable energy techniques which encompass both generation and power management solutions are fundamental for meeting remote residential energy supply and demand today, especially if the grid is quasi-inexistent. Solar thermoelectric generators can be a cost-effective alternative to photovoltaics for a remote residential household power supply. A complete solar thermoelectric energy harvesting system is presented for energy delivery to remote residential areas in developing regions. To this end, the entire system was built, modeled, and then validated with LTspice simulator software via thermal-to-electrical analogy schemes. Valuable data in conjunction with two novel LTspice circuits were obtained, showing …

Mitigation Of Moving Shocks In An Expanding Duct, Veraun Chipman

UNLV Theses, Dissertations, Professional Papers, and Capstones

Inviscid flow theory governs the bulk motion of a gas at some distance away from the walls (i.e. outside the boundary layer). That is to say, there are no viscous forces in the bulk flow, which is modeled using the Euler equations. The Euler equations are simply the Navier-Stokes equations with zero viscosity terms. An ideal inviscid fluid, when brought into contact with a surface or wall, would naturally slip right past it since the fluid has no viscosity. In real life, however, a thin boundary layer forms between the wall or surface and the bulk flow. Shock wave boundary …

Designing A Biomimetic Testing Platform For Actuators In A Series-Elastic Co-Contraction System, Ryan Tyler Schroeder

UNLV Theses, Dissertations, Professional Papers, and Capstones

Actuators determine the performance of robotic systems at the most intimate of levels. As a result, much work has been done to assess the performance of different actuator systems. However, biomimetics has not previously been utilized as a pretext for tuning a series elastic actuator system with the purpose of designing an empirical testing platform. Thus, an artificial muscle tendon system has been developed in order to assess the performance of two distinct actuator types: (1) direct current electromagnetic motors and (2) ultrasonic rotary piezoelectric motors. Because the design of the system takes advantage of biomimetic operating principles such as …

Development Of A Black-Box Transient Thermal Model For Residential Buildings, Andrew Cross

UNLV Theses, Dissertations, Professional Papers, and Capstones

Heavily populated metropolitan areas located in cooling-dominated climates, as are found in the Desert Southwest, pose a challenge to electrical utilities that service these areas. During the late afternoons of the summer months, residents of these metropolitan areas require larger than normal amounts of power to run their homes' air conditioning systems, at significant expense to the utilities. In the study reported here, interior temperature and power consumption data, accumulated over the course of a year and a half from seven houses within a Las Vegas neighborhood, are used to develop a predictive black-box statistical model for residential thermal transience. …

Study Of Water Transport Phenomena On Cathode Of Pemfcs Using Monte Carlo Simulation, Karn Soontrapa

UNLV Theses, Dissertations, Professional Papers, and Capstones

This dissertation deals with the development of a three-dimensional computational model of water transport phenomena in the cathode catalyst layer (CCL) of PEMFCs. The catalyst layer in the numerical simulation was developed using the optimized sphere packing algorithm. The optimization technique named the adaptive random search technique (ARSET) was employed in this packing algorithm. The ARSET algorithm will generate the initial location of spheres and allow them to move in the random direction with the variable moving distance, randomly selected from the sampling range, based on the Lennard-jones potential of the current and new configuration. The solid fraction values obtained …

3d Modeling And Design Optimization Of Rod Shaped Ionic Polymer Metal Composite Actuator, Siul A. Ruiz

UNLV Theses, Dissertations, Professional Papers, and Capstones

Ionic polymer-metal composites (IPMCs) are some of the most well-known electro-active polymers. This is due to their large deformation provided a relatively low voltage source. IPMCs have been acknowledged as a potential candidate for biomedical applications such as cardiac catheters and surgical probes; however, there is still no existing mass manufacturing of IPMCs. This study intends to provide a theoretical framework which could be used to design practical purpose IPMCs depending on the end users interest.

This study begins by investigating methodologies used to develop quantify the physical actuation of an IPMC in 3-dimensional space. This approach is taken in …

Predicting The Performance Of A Solar Domestic Water Heating System With Evacuated Tube Collectors And Hydronic Radiant Flooring, Kimberly Nicole Hammer

UNLV Theses, Dissertations, Professional Papers, and Capstones

Residential solar thermal system installations have been significantly increasing in the last decade and there exists limited resources for reasonably predicting the performance of those systems. A simulated model is developed in MATLAB® and used to predict the performance of a solar domestic water heating system. In the simulated system, hot water is generated using evacuated tube solar collectors and stored in a domestic hot water storage tank, which utilizes immersed coil heat exchangers. The system is designed to provide hydronic radiant floor heating to its occupants based on the heat loss of a building energy model for an energy-efficient …

Investigation Of Peak Load Reduction Strategies In Residential Buildings In Cooling Dominated Climates, Fady Atallah

UNLV Theses, Dissertations, Professional Papers, and Capstones

This investigation of peak load reduction strategies in residential buildings contributes to the global international efforts in reducing energy consumption and is related directly to energy efficiency in residential and commercial buildings. Work reported here involves computer aided building energy simulation of energy efficient and non-energy efficient residential homes coupled with empirical energy consumption data gathered from monitoring an array of energy efficient residential homes. The latter have been implemented for peak load reduction strategies. In addition non-energy efficient residential homes have been monitored to compare performance to the energy efficient homes. This study demonstrates the crucial importance of energy …

Buffering Pv Output During Cloud Transients With Energy Storage, Yacouba Moumouni

UNLV Theses, Dissertations, Professional Papers, and Capstones

Consideration of the use of the major types of energy storage is attempted in this thesis in order to mitigate the effects of power output transients associated with grid-tied CPV systems due to fast-moving cloud coverage. The approach presented here is to buffer intermittency of CPV output power with an energy storage device (used batteries) purchased cheaply from EV owners or battery leasers. When the CPV is connected to the grid with the proper energy storage, the main goal is to smooth out the intermittent solar power and fluctuant load of the grid with a convenient control strategy. This thesis …

Improving Efficiency And Capacity Of Hydro-Turbines In The Western United States, Hoover Dam, Jonathan Sanchez

UNLV Theses, Dissertations, Professional Papers, and Capstones

The goal for this thesis is to minimize clearances and tolerances, in order to prevent water leakage. A proper seal on the seal rings does not let excess water flow through the turbine runner, thus conserving more water and wasting less energy. Moreover, water leakage past worn wear plates allows for an extra load for the turbine when operating in condense mode. When the wicket gates are closed, water leakage past worn plates wastes mechanical energy in the water; thus, decreasing the efficiency of the Francis turbine, especially when operating at partial loads. Furthermore, the wicket gates also known as …

Quantification Of Stochastic Uncertainty Propagation For Monte Carlo Depletion Methods In Reactor Analysis, Quentin Thomas Newell

UNLV Theses, Dissertations, Professional Papers, and Capstones

The Monte Carlo method provides powerful geometric modeling capabilities for large problem domains in 3-D; therefore, the Monte Carlo method is becoming popular for 3-D fuel depletion analyses to compute quantities of interest in spent nuclear fuel including isotopic compositions. The Monte Carlo approach has not been fully embraced due to unresolved issues concerning the effect of Monte Carlo uncertainties on the predicted results.

Use of the Monte Carlo method to solve the neutron transport equation introduces stochastic uncertainty in the computed fluxes. These fluxes are used to collapse cross sections, estimate power distributions, and deplete the fuel within depletion …

Energy-Based Analysis Of Utility Scale Hybrid Power Systems, Kwame Agyenim-Boateng

UNLV Theses, Dissertations, Professional Papers, and Capstones

The promise of large-scale use of renewables such as wind and solar for supplying electrical power is tempered by the sources' transient behavior and the impact this would have on the operation of the grid. Among the methods cited for addressing some of those concerns are exploring the complementary nature of solar and wind power generation, and through the use of supplemental energy storage. While the technology for the latter has not been proven to be economical on a large scale at the present time, some assessments of what magnitude is required can be made. An energy-based analysis of utility …

Modeling Of A Novel Solar Down Beam Test Facility Utilizing Newtonian Optics, Ryan J. Hoffmann

UNLV Theses, Dissertations, Professional Papers, and Capstones

As advances in concentrated solar energy progress there will inevitably be an increase in the demand of resources for testing new conceptions. Currently, there are limited facilities available for taking concentrated solar energy concepts from the laboratory bench scale to the engineering test scale. A proposed solution is a scientific and developmental facility that provides highly concentrated solar energy at ground level. The design presented is a solar down beam test facility utilizing a Newtonian optics approach with a flat rectangular down beam mirror to reflect and concentrate the sun's rays at ground level.

Literature review suggests a hyperbolic reflector …

Fenestration Studies On Building Energy Using The Facade Evaluation Facility, Wendell Cocina

UNLV Theses, Dissertations, Professional Papers, and Capstones

The project was developed to assess several types of facades and their influence on building energy, mainly focused on windows and other building fenestrations. Requirements for the facility are stated in this paper alongside corresponding solutions. The facility is designed to represent a section of a building façade. Experimenting on a wide range of fenestrations including windows with integrated PV elements was the primary prerequisite. The option of removable façade configurations was used and allowed testing specimens to be changed effortlessly. Instrumentation and data acquisition are discussed including calibration and uncertainty analysis. Investigation of the air conditioning unit was concluded …

Time-Dependent Crack Growth Behavior Of Alloy 617 And Alloy 230 At Elevated Temperatures, Shawoon Kumar Roy

UNLV Theses, Dissertations, Professional Papers, and Capstones

Two Ni-base solid-solution-strengthened superalloys: INCONEL 617 and HAYNES 230 were studied to check sustained loading crack growth (SLCG) behavior at elevated temperatures appropriate for Next Generation Nuclear Plant (NGNP) applictaions with constant stress intensity factor (K _max = 27.75 MPa[checkmark]m) in air. The results indicate a time-dependent rate controlling process which can be characterized by a linear elastic fracture mechanics (LEFM) parameter - stress intensity factor (K). At elevated temperatures, the crack growth mechanism was best described using a damage zone concept. Based on results and study, SAGBOE (stress accelerated grain boundary oxidation embrittlement) is considered the primary reason for …