Open Access. Powered by Scholars. Published by Universities.®
Physical Sciences and Mathematics Commons™
Open Access. Powered by Scholars. Published by Universities.®
Articles 1 - 6 of 6
Full-Text Articles in Physical Sciences and Mathematics
Dependence Of Resistivity In Low-Density Polyethylene On Space Environment Parameters, John R. Dennison, Jerilyn Brunson
Dependence Of Resistivity In Low-Density Polyethylene On Space Environment Parameters, John R. Dennison, Jerilyn Brunson
All Physics Faculty Publications
The conductivity of high-resistivity polymer films is dependent on the magnitude of applied electric field, repeated electric field exposure, and sample temperature. A traditional constant voltage method was used, maintained under vacuum to more closely resemble the space environment. Both the strength of the applied voltage and the thickness of low-density polyethylene (LDPE) samples were varied to determine the electric field dependence of internal polarization and the leakage current most appropriate in calculating the resistivity. Repetition of same field strength measurements determined the influence of sample history and charging memory. Measuring the resistivity from cryogenic temperatures to well above the …
Low Temperature Measurements Of Resistivity In Low-Density Polyethylene, John R. Dennison, J. Brunson
Low Temperature Measurements Of Resistivity In Low-Density Polyethylene, John R. Dennison, J. Brunson
All Physics Faculty Publications
Measurements of resistivity of low density polyethylene (LDPE) have been made using the standard constant voltage method to determine the temperature dependence of resistivity. Where electrons are assumed to serve as the primary charge carriers, their mobility is believed to be dependent on their probability of hopping between trapping sites treated as potential wells. We consider our measurements of this relatively simple polymeric material using temperature-dependant models of conduction mechanisms developed for amorphous solids and semi-conductors.
State Of Utah Space Environment & Contamination Study (Suspecs) Misse-6 Payload To Investigate Their Effects On Electron Emission And Resistivity Of Spacecraft Materials, John R. Dennison, L. Pearson, L. Davis, J. W. Burns, R. S. Hyde, James S. Dyer, Tina Andrus, Andrew Jay Auman, Jeff Duce, Tim Neilsen, Rob Leishman
State Of Utah Space Environment & Contamination Study (Suspecs) Misse-6 Payload To Investigate Their Effects On Electron Emission And Resistivity Of Spacecraft Materials, John R. Dennison, L. Pearson, L. Davis, J. W. Burns, R. S. Hyde, James S. Dyer, Tina Andrus, Andrew Jay Auman, Jeff Duce, Tim Neilsen, Rob Leishman
All Physics Faculty Publications
A study of the effects of prolonged exposure to the space environment and of charge-enhanced contamination on the electron emission and resistivity of spacecraft materials, the State of Utah Space Environment & Contamination Study (SUSpECS), is planned for flight aboard the MISSE-6 payload. The Materials International Space Station Experiment (MISSE-6) program is designed to characterize the performance of candidate new space materials over the course of approximately four to eight month exposure periods on-orbit on the International Space Station, with a target flight date of mid-2006. The study is conducted by the Utah State University Materials Physics Group, in cooperation …
Measuring Charge Storage Decay Time And Resistivity Of Spacecraft Insulators, Jerilyn Brunson, John R. Dennison
Measuring Charge Storage Decay Time And Resistivity Of Spacecraft Insulators, Jerilyn Brunson, John R. Dennison
All Physics Faculty Publications
An informal discussion of how accurate measurements of resistivity and increasing understanding of the behavior of insulating materials used on spacecraft is fundamental to advancing the design and utility of the spacecraft. Build up of charge can vary between different areas of the spacecraft, with excess charge accumulating and leading to functional anomalies or component failure. The most important parameter in determining how charge will decay through an insulator is the resistivity of the material. Current industry standards for measuring resistivity have been shown to be inconsistent with actual phenomena, and new methods of measuring resistivity must be developed and …
Experimentally Derived Resistivity For Dielectric Samples From The Crres Internal Discharge Monitor, Nelson W. Green, A. Robb Frederickson, John R. Dennison
Experimentally Derived Resistivity For Dielectric Samples From The Crres Internal Discharge Monitor, Nelson W. Green, A. Robb Frederickson, John R. Dennison
All Physics Faculty Publications
Resistivity values were experimentally determined using charge storage methods for six samples remaining from the construction of the Internal Discharge Monitor (IDM) flown on the Combined Release and Radiation Effects Satellite (CRRES). Three tests were performed over a period of four to five weeks each in a vacuum of ~5×10-6 torr with an average temperature of ~25 ºC to simulate a space environment. Samples tested included FR4, PTFE, and alumina with copper electrodes attached to one or more of the sample surfaces. FR4 circuit board material was found to have a dark current resistivity of ~1×1018 Ω-cm and a moderately …
Proposed Modifications To Engineering Design Guidelines Related To Resistivity Measurements And Spacecraft Charging, John R. Dennison, Prasanna Swaminathan, Randy Jost, Jerilyn Brunson, Nelson W. Green, A. Robb Frederickson
Proposed Modifications To Engineering Design Guidelines Related To Resistivity Measurements And Spacecraft Charging, John R. Dennison, Prasanna Swaminathan, Randy Jost, Jerilyn Brunson, Nelson W. Green, A. Robb Frederickson
All Physics Faculty Publications
A key parameter in modeling differential spacecraft charging is the resistivity of insulating materials. This parameter determines how charge will accumulate and redistribute across the spacecraft, as well as the time scale for charge transport and dissipation. Existing spacecraft charging guidelines recommend use of tests and imported resistivity data from handbooks that are based principally upon ASTM methods that are more applicable to classical ground conditions and designed for problems associated with power loss through the dielectric, than for how long charge can be stored on an insulator. These data have been found to underestimate charging effects by one to …