Physical Sciences and Mathematics Commons^™

The Study Of Corrosion On Additive-Manufactured Metals., Braydan Daniels

Electronic Theses and Dissertations

The purpose of this study was to investigate and compare the corrosion mechanisms between wrought and additive-manufactured (3D-printed) copper and stainless steel. The experimental procedure consisted of measuring the open circuit potential, electrochemical impedance spectroscopy, linear sweep voltammetry, Tafel analysis, surface topology, and scanning electron microscopy for each metal within salt water, tap water, sulfuric acid, and synthetic body fluid (excluding copper in synthetic body fluid).

Overall, printed stainless steel was more corrosion-resistant than wrought stainless steel in tap water and synthetic body fluid based on OCP, LSV, and surface topology results. Additionally, printed copper was more corrosion-resistant than wrought …

Use Of Electrochemical Techniques And Statistical Analysis To Investigate The Pitting Probability Of Copper, Sina Matin

Electronic Thesis and Dissertation Repository

The development of a safe permanent disposal plan is essential for the long-term disposal of used fuel bundles. Nuclear Waste Management Organization (NWMO) has been investigating the deep geologic disposal of nuclear waste which offers the optimum passive safety system with a negligible probability of release of radionuclides into the environment.

The proposed used fuel containers (UFC) for the permanent disposal of high-level nuclear waste in Canada is comprised of a carbon steel vessel coated with a 3 mm corrosion-resistant copper layer deposited using a combination of electrodeposition and cold spray deposition. Although copper is often considered to be thermodynamically …

Characterization Of Deposited Copper Oxide Films On Copper Substrates, Millicent Castillo

Electronic Thesis and Dissertation Repository

The deposition of copper oxide films on copper substrates was investigated by the electrochemical, thermal, and hydrothermal oxidation of copper. The formed oxides were characterized using various surface analytical techniques to determine the film’s morphology, composition, and thickness. The results show that by growing oxides electrochemically, a duplex layer composing of CuO and Cu₂O film was formed on the copper surface, having characteristics of being porous and possessing needle-like structures. An oxide film composed of CuO and Cu₂O, which shows minimal porosity and possess mixtures of crystalline and non-crystalline structures, is formed on the copper surface …

Surface Modification Of Carbon-Based Electrodes For Electrochemical Conversion Processes: Oxygen Reduction Reaction And Bicarbonate Conversion, Udari Shyamika Kodithuwakku Arachchige

Theses and Dissertations--Chemistry

Oxygen reduction reaction (ORR) and conversion of bicarbonate into value-added chemicals are two significant electrochemical processes for energy storage and conversion. ORR is an important electrochemical reaction in fuel cells and metal-air batteries that provide power conversion and storage capacity, respectively, for portable electronics, and electric vehicles. However, the performance of catalysts (e.g., platinum-based) is critically limited by slow kinetics, inefficient four-electron pathway, and surface deactivation. This limited performance of platinum-based catalysts, the scarcity of platinum, and vulnerable supply chains for critical minerals require the development of alternative electrocatalysts now more than ever. Carbon-based materials possess several key properties that …

Galvanic Corrosion Of Carbon Steel Coupled To Copper In Used Nuclear Fuel Containers, Lindsay J. Braithwaite

Electronic Thesis and Dissertation Repository

Deep geological containment of used nuclear fuel will rely on multiple engineered and natural barriers, two of which are the copper-coated used fuel containers and the compacted bentonite clay buffer boxes in which the containers will rest. This work focused on possible galvanic interactions between the copper coating and the steel substrate of the container, which may occur at a hypothetical through-coating defect. In the presence of various amounts of chloride, bentonite, and oxygen, corrosion of the copper/carbon steel couple was studied using electrochemical tests complemented by surface characterization and 3D X-ray imaging. We investigated the effects of copper-to-steel area …

The Electrochemical And Corrosion Study Of Copper For Nuclear Waste Containers Under Deep Geological Disposal Conditions, Mengnan Guo

Electronic Thesis and Dissertation Repository

The proposed method for the safe disposal of Swedish, Finnish, and Canadian high-level nuclear waste (HLNW) is to isolate it in iron or steel containers with an outer copper (Cu) shell or coating and bury it in a deep geological repository (DGR). Copper has been selected as the corrosion barrier due to its stability in the aqueous anoxic environments anticipated in DGR conditions. The container will initially be exposed to humid aerated conditions which will evolve to cool and anoxic as radiation fields in the fuel decay and heat production ceases. When the DGR is cool and anoxic, sulphide (SH …

Galvanic Corrosion Of Copper-Coated Carbon Steel For Used Nuclear Fuel Containers, Thalia E. Standish

Electronic Thesis and Dissertation Repository

Carbon steel vessels coated with ∼3 mm of Cu have been proposed for the permanent disposal of used nuclear fuel in a deep geological repository (DGR) in Canada. In the event of an undetected defect in the Cu coating that exposes the steel substrate, galvanically accelerated corrosion of steel is, in principle, possible. To investigate this scenario, the progression of steel corrosion at the base of novel simulated through-coating defects was monitored electrochemically and imaged non-destructively using X-ray micro-computed tomography (micro-CT) as a function of time, O₂ availability (including anoxic conditions), and coating method (cold spray deposition (with and …