Medicine and Health Sciences Commons^™

Bioresorbable Composite Polymeric Materials For Tissue Engineering Applications, Sakineh Hajebi, Saeed Mohammadi Nasr, Navid Rabiee, Mojtaba Bagherzadeh, Sepideh Ahmadi, Mohammad Rabiee, Mohammadreza Tahriri, Lobat Tayebi, Michael R. Hamblin

School of Dentistry Faculty Research and Publications

This review covers the development of bioresorbable polymeric composites for applications in tissue engineering. Various commercially available bioresorbable polymers are described, with emphasis on recent bioresorbable composites based on natural and synthetic polymers. Bioresorbable polymers contain hydrolyzable bonds, which are subjected to chemical degradation via either reactive hydrolysis or enzyme-catalyzed active hydrolysis. For synthetic polymers, chemical hydrolysis is the most important mode of degradation. The degradation rate can be controlled by varying the molecular weight and crystallinity. Examples of bioresorbable polymers are: polyurethane, poly(D,L)lactide, poly(lactic-co-glycolic) acid, poly(α-hydroxy acids), cross-linked polyester hydrogels, poly(orthoesters), polyanhydrides and polyethylene glycol.

Fibroblast Encapsulation In Gelatin Methacryloyl (Gelma) Versus Collagen Hydrogel As Substrates For Oral Mucosa Tissue Engineering, Fahimeh Tabatabaei, Keyvan Moharamzadeh, Lobat Tayebi

School of Dentistry Faculty Research and Publications

Purpose

Over the past decades, a variety of biomaterials have been investigated in terms of their suitability for oral mucosa tissue engineering. The aim of this study was to compare collagen and GelMA hydrogels as connective tissue scaffolds for fibroblasts and as substrates for seeding and culture of oral epithelial keratinocyte cells.

Methods

Human primary oral fibroblast and keratinocyte cells were isolated from gingival biopsies. The mixture of fibroblasts with GelMA or collagen gel were aliquoted within six-well tissue culture plate inserts and cross-linked using visible light or reconstitution buffer/heat, respectively. The viability of fibroblasts in the hydrogels was investigated …

Incorporation Of Functionalized Reduced Graphene Oxide/Magnesium Nanohybrid To Enhance The Osteoinductivity Capability Of 3d Printed Calcium Phosphate-Based Scaffolds, Meisam Omidi, Hossein Golzar, Dorsa Mohammadrezaei, Amir Yadegari, Morteza Rasoulianboroujeni, Mohadeseh Hashemi, Fatemeh Yazdian, Mohammad Shalbaf, Lobat Tayebi

School of Dentistry Faculty Research and Publications

Improving bone regeneration is one of the most pressing problems facing bone tissue engineering (BTE) which can be tackled by incorporating different biomaterials into the fabrication of the scaffolds. The present study aims to apply the 3D-printing and freeze-drying methods to design an ideal scaffold for improving the osteogenic capacity of Dental pulp stem cells (DPSCs). To achieve this purpose, hybrid constructs consisted of 3D-printed Beta-tricalcium phosphate (β-TCP)-based scaffolds filled with freeze-dried gelatin/reduced graphene oxide-Magnesium-Arginine (GRMA) matrix were fabricated through a novel green method. The effect of different concentrations of Reduced graphene oxide-Magnesium-Arginine (RMA) (0, 0.25% and 0.75%wt) on the …

Polymeric Scaffolds For Dental Pulp Tissue Engineering: A Review, Hossein E. Jazayeri, Su-Min Lee, Lauren Kuhn, Farahnaz Fahimipour, Mohammadreza Tahriri, Lobat Tayebi

School of Dentistry Faculty Research and Publications

Objectives

The purpose of this review is to describe recent developments in pulp tissue engineering using scaffolds and/or stem cells. It is crucial to understand how this approach can revitalize damaged dentin-pulp tissue. Widespread scaffold materials, both natural and synthetic, and their fabrication methods, and stem-progenitor cells with the potential of pulp regeneration will be discussed.

Data and Sources

A review of literature was conducted through online databases, including MEDLINE by using the PubMed search engine, Scopus, and the Cochrane Library.

Study Selection

Studies were selected based on relevance, with a preference given to recent research, particularly from the past …

Design Of A New 3d‐Printed Joint Plug, Lobat Tayebi, Zhanfeng Cui, Hua Ye

School of Dentistry Faculty Research and Publications

This paper introduces a kit of parts as a novel three‐dimensional (3D)–printed joint plug, in which each of the parts function cooperatively to treat cartilage damage in joints of the human body (e.g., hips, wrists, elbow, knee, and ankle). Three required and one optional parts are involved in this plug. The first part is a 3D‐printed hard scaffold (bone portion) to accommodate bone cells, and the second is a 3D‐printed soft scaffold (cartilage portion) overlying the bone portion to accommodate chondrocytes. The third part of joint plug is a permeable membrane, termed film, to cover the entire plug to provide …

3d Printed Tcp-Based Scaffold Incorporating Vegf-Loaded Plga Microspheres For Craniofacial Tissue Engineering, Farahnaz Fahimipour, Morteza Rasoulianboroujeni, Erfan Dashtimoghadam, Kimia Khoshroo, Mohammadreza Tahriri, Doug Lobner, Lobat Tayebi

School of Dentistry Faculty Research and Publications

Objective

Vascularization is a critical process during bone regeneration/repair and the lack of tissue vascularization is recognized as a major challenge in applying bone tissue engineeringmethods for cranial and maxillofacial surgeries. The aim of our study is to fabricate a vascular endothelial growth factor (VEGF)-loaded gelatin/alginate/β-TCP composite scaffold by 3D printing method using a computer-assisted design (CAD) model.

Methods

The paste, composed of (VEGF-loaded PLGA)-containing gelatin/alginate/β-TCP in water, was loaded into standard Nordson cartridges and promptly employed for printing the scaffolds. Rheological characterization of various gelatin/alginate/β-TCP formulations led to an optimized paste as a printable bioink at room …

Development Of 3d Pcl Microsphere/Tio2 Nanotube Composite Scaffolds For Bone Tissue Engineering, Kimia Khoshroo, Tahereh S. Jafarzadeh Kashi, Fathollah Moztarzadeh, Mohammadreza Tahriri, Hossein E. Jazayeri, Lobat Tayebi

School of Dentistry Faculty Research and Publications

In this research, the three dimensional porous scaffolds made of a polycaprolactone (PCL) microsphere/TiO₂ nanotube (TNT) composite was fabricated and evaluated for potential bone substitute applications. We used a microsphere sintering method to produce three dimensional PCL microsphere/TNT composite scaffolds. The mechanical properties of composite scaffolds were regulated by varying parameters, such as sintering time, microsphere diameter range size and PCL/TNT ratio. The obtained results ascertained that the PCL/TNT (0.5 wt%) scaffold sintered at 60 °C for 90 min had the most optimal mechanical properties and an appropriate pore structure for bone tissue engineering applications. The average pore size …

Development Of Plga-Coated Β-Tcp Scaffolds Containing Vegf For Bone Tissue Engineering, Arash Khojasteh, Farahnaz Fahimipour, Mohamadreza Baghaban Eslaminejad, Mohammad Jafarian, Shahrbanoo Jahangir, Farshid Bastami, Mohammadreza Tahriri, Akbar Karkhaneh, Lobat Tayebi

School of Dentistry Faculty Research and Publications

Bone tissue engineering is sought to apply strategies for bone defects healing without limitations and short-comings of using either bone autografts or allografts and xenografts. The aim of this study was to fabricate a thin layer poly(lactic-co-glycolic) acid (PLGA) coated beta-tricalcium phosphate (β-TCP) scaffold with sustained release of vascular endothelial growth factor (VEGF). PLGA coating increased compressive strength of the β-TCP scaffolds significantly. For in vitro evaluations, canine mesenchymal stem cells (cMSCs) and canine endothelial progenitor cells (cEPCs) were isolated and characterized. Cell proliferation and attachment were demonstrated and the rate of cells proliferation on the VEGF released scaffold was …