Engineering Commons^™

Optimization Of Hydraulic Cylinder Positioning For Wind Tower Hydraulic Erection System, Anbesh Rawal

Master's Theses

Wind produced electricity is a rapidly growing field with wind towers serving as critical components. Conventionally, special cranes are commonly used for wind tower erection. This study explores the use of hydraulic cylinders for small-scale wind tower erection. The thesis aims to find the optimal position of hydraulic cylinder connections in a hydraulic erection system for safe and energy-efficient tower erection and retraction and to enhance the performance and longevity of the system.

Structural analysis was conducted to investigate various hydraulic cylinder positioning configurations, ensuring minimal force exertion while maintaining structural integrity. The study included the selection of locally available …

Surrogate-Assisted Simulation-Optimization Framework For Groundwater Management In A Multi-Aquifer System, Melika Mani

LSU Master's Theses

Uncontrolled groundwater exploitation can lead to aquifer depletion, land subsidence, and saltwater intrusion. Effective groundwater management is challenging due to the intricate nature of subsurface hydrogeology and spatiotemporally variable pumping, especially in a multi-aquifer system. To ensure sustainable withdrawal, multi-objective optimization is an effective tool for balancing management goals and drawdown effects. However, running simulation-optimization using detailed groundwater models is computationally expensive, pushing decision-makers to decide based on limited scenarios. In this study, a hydrogeological framework was constructed for the Capital Area, Louisiana, allowing for individual assessment of each unit to better understand each aquifer's condition. Moreover, a surrogate-assisted simulation-optimization …

Developing A Smart And Sustainable Public Transportation System: A Case Study In Camden, New Jersey, Zahra Vafakhah

Theses and Dissertations

The transportation sector is a major contributor to air pollution and Greenhouse Gas (GHG) emissions. As a significant source of emissions, public transportation presents an opportunity for mitigation through electrification. However, transitioning to an electric bus fleet necessitates substantial investments in bus procurement and charging infrastructure. To address the associated costs, this study introduces a mixed-integer linear mathematical model developed to optimize the location of on-route fast charging stations within bus networks. The central objective of this optimization formulation is to minimize the overall cost of establishing the charging infrastructure. The study employs a real-world case study focusing on a …

A Systems Approach To Design And Plan Sustainable Antifragile Infrastructure Based On Aggregate Footprint And Satisfaction, Farboud Khatami

Theses and Dissertations

The concepts of robustness and sustainability in planning and design of water and energy infrastructures have been extensively explored in previous research, primarily focusing on system reliability, environmental considerations, and economic aspects. This study aims to broaden the understanding of these concepts by offering comprehensive frameworks that capture the essence of robustness and sustainability at two distinct levels.

The first level of investigation focuses on the performance of infrastructure networks during natural disasters. Traditionally, this has been addressed using reliability, resilience, and vulnerability metrics. However, these methods rely on static, deterministic, and non-stationary data, which is inadequate when dealing with …

Optimizing Locations And Sizes Of Asphalt Concrete Plants In Karbala, Iraq, Ghayath Ali, Sawsan R Mohammad, Alaa M. Abdulhussein

Al-Bahir Journal for Engineering and Pure Sciences

This study develops and presents a methodology for determining the optimal geographic distribution and size of asphalt concrete plants in Karbala, Iraq, in order to minimize the cost of asphalt concrete produced. The purpose of this study is to discuss these points. The methodology can identify potential locations for asphalt concrete plants within a study area, considering the plants' operation and capital costs and the costs of transporting raw materials to the plants and asphalt concrete to demand centers. Matrix Laboratory (MATLAB) software have been used to program the methodology. This methodology has been applied to Karbala using actual data. …

Energy Harvesting For Self-Powered Sensors For Smart Transportation Infrastructures, Anil K. Agrawal, Mohsen Amjadian, Hani Nassif

Civil Engineering Faculty Publications and Presentations

In this research project, an Electromagnetic Energy Harvesting System (EMEHS) is developed for harvesting the kinetic energy of ambient and traffic-induced vibrations and carry out a detailed feasibility study and impacts of such system for application on transportation infrastructures. The proposed EMEHS utilizes the innovative concept of creating array of large number of small permanent magnets through certain optimization criteria to achieve strong and focused magnetic field in a particular orientation. When these magnets are attached to a flexible sub-system and placed close to the copper coil, ambient and traffic-induced vibration of the sub-system induces eddy current in copper the …

Evaluation Of Il-17a And Il-17f Gene Expression In Peripheral Blood Mononuclear Cells In Different Clinical Stages Of Chronic Hepatitis B Infection In An Iranian Population, Tannaz Akbari Kolagar, Seyed Reza Mohebbi, Fatemeh Ashrafi, Shahrzad Shoraka, Hamid Asadzadeh Aghdaei, Mohammad Reza Zali

Makara Journal of Technology

Hepatitis B virus (HBV) infection is one of the main causes of liver damage, which can also lead to chronic hepatitis B (CHB) infection. More than 240 million individuals worldwide are chronic carriers of HBV. Among individuals with CHB who are untreated, approximately 15% – 40% will progress to liver cirrhosis or cancer. The interactions between HBV and host immune response play significant roles in the progression of CHB. CHB can be generally divided into four different clinical phases: immune tolerance (IT), immune clearance, inactive carrier, and Hepatitis B surface antigen (HBsAg)-negative reactivation phase (ENEG). Many studies showed that interleukins …

Microstrip Filters: A Review Of Different Filter Designs Used In Ultrawide Band Technology, Hussain Bohra, Giriraj Prajapati

Makara Journal of Technology

In this study, optimization techniques applied in designing microstrip bandpass ultra-wideband (UWB) filters are presented. Optimization based on various defected ground structure techniques, resonator designs, and type of dielectric materials is discussed. Microstrip bandpass filters implemented at UWB frequency bands used in wireless communication systems have key features to control frequency response in passband and stopband. Optimization techniques are studied to attain optimum performance of bandpass microstrip filters to ensure minimum insertion loss, high selectivity, compactness, sharp transitions at cut-off frequencies, high return loss, and excellent linearity. Extensive study shows that proper selection of fabrication techniques and type of material …

Design Optimization Of Steel Building Using Minlp, Tomaž Žula

UBT International Conference

The paper presents the design optimization of the steel building. The structure consists of the main portal frames, which are mutually connected with the purlins. It is proposed that all structural elements are constructed from standard hot rolled IPE sections. The structural optimization is calculated by the mixed-integer non-linear programming approach, MINLP. The dimensioning of steel members is carried out in accordance with the design specifications of Eurocode 3. The Modified Outer-Approximation/Equality-Relaxation (OA/ER) algorithm, a three-phase MINLP strategy and a special prescreening procedure of discrete alternatives are used for the optimization. In addition to the optimal structural mass, the optimal …

Failure Sampling With Optimized Ensemble Approach For The Structural Reliability Analysis Of Complex Problems, Christopher Eamon, Kapil Patki, Ahmad Alsendi

Civil and Environmental Engineering Faculty Research Publications

Failure sampling is a structural reliability method based on modified conditional expectation suitable for complex problems for which reliability index-based approaches are inapplicable and simulation is needed. Such problems tend to have non-smooth limit state boundaries or are otherwise highly nonlinear. Previous studies recommended implementation of failure sampling with an extrapolation technique using Johnson's distribution or the generalized lambda distribution. However, what implementation method works best is problem dependent. The uncertainty of which approach provides best results for a particular problem limits the potential effectiveness of the method. In this study, a solution is proposed to this issue that eliminates …

A Multi-Objective Optimization Model To Minimize The Gap In Accessibility To Multi-Use Paths While Maximizing The Economic Efficiency Of Active Transportation Investments For Fresno, California, Chih-Hao Wang

Mineta Transportation Institute Publications

This research examines the accessibility to multi-use paths in a variety of neighborhoods in Fresno, California. This study aims to develop a multi-objective optimization modeling framework to be used by decision makers in transportation and policy to maximize the total accessibility to multi-use paths across the city while minimizing the gap between low- and high- accessibility neighborhoods by an optimal allocation of active transportation. Researchers calculate accessibility to multi-use paths by measuring the total length of multi-use paths (walkway and bikeway) a resident could reach from their own Census block group with a 30-minute cycling ride. The study employs a …

Multi-Objective Optimization Of A Ridesharing System Performance, Mohammad Nasr Azadani

Graduate Theses, Dissertations, and Problem Reports

Ridesharing is a shared vehicle service with the potential to meet the growing travel demand due to population increase, economic growth, and shortage in transportation infrastructure capacity. Compared to the current system of predominantly using personal vehicles, ridesharing services reduce the number of vehicles while providing mobility services to the same number of people with no additional investment in the transportation infrastructure. One of the big challenges in implementing ridesharing services is matching drivers and riders. Conflicts between matching-objectives to comply with the interests of diverse stakeholders influence the efficiency of ridesharing in a transportation system. This study investigates the …

Reliability Assessment And Optimization Of Water Distribution Systems Explicitly Considering Isolation Valve Locations, Erika Hernandez Hernandez

Theses and Dissertations--Civil Engineering

Water distribution systems have changed the landscape of communities through two services: 1) providing water supply for domestic and industrial use, and 2) providing water required to fight fires. However, a substantial portion of the water infrastructure in the country, as many of other public assets built over 50 years ago, are now reaching the end of their useful life; which combined with rapid growth and changes in demographics have placed water distribution pipe networks at a state that requires revitalization. The aging infrastructure along with the growing threat of natural and man-made disruptions have led water utilities to place …

Sizing A New Bike Sharing System For The University Of Nevada, Las Vegas, Nesley Orochena

UNLV Theses, Dissertations, Professional Papers, and Capstones

The strategic planning objectives for a novel Bike Sharing Systems (BSS) are to locate the BSS stations, size the stations, and determine the bicycle fleet size, among others. Current guidelines to design BSS programs are tailored to city centers with large coverage areas and high bicycle to population ratios, and thus not directly transferable to a university setting. An ordered probit model was created using data from a university online stated preference survey to determine the key factors that affect the uptake rates for the UNLV BSS program and to estimate the potential demand. The demand analysis was incorporated into …

Evaluation Of Internally Cured Bridge Deck Concrete With Standard And Optimized Aggregate Gradation, Arman Abdigaliyev

Department of Civil and Environmental Engineering: Dissertations, Theses, and Student Research

Due to the relatively high cement content and low water-to-cement ratio (w/c) used, bridge deck concrete is prone to premature cracking. Internal curing has been found to greatly reduce the chance of premature cracking as well as concrete deterioration. This research developed internally cured bridge deck concrete based on a local mix design in Nebraska. Four different lightweight fine aggregate (LWFA) as internal curing agents were evaluated and their effects on fresh, mechanical, durability, and shrinkage properties of concrete were studied. The study focused on resolving two issues associated with fine aggregate replacement based on Bentz equation. To identify the …

Structural Optimization Of Cable-Stayed Bridges Considering The Action Of Permanent And Transitory Loads, Carolina Almeida Novaes Dos Santos

Electronic Thesis and Dissertation Repository

Cable-stayed bridges are complex structures with several advantages such as aesthetical appeal, economic use of materials, and efficient construction method. Due to these advantages and the extensive knowledge gained from projects over the years, longer cable-stayed bridges are being constructed. As span lengths increase, structures become more flexible, which makes the accurate evaluation of wind loads critically important in the design of cable-stayed bridges. A large number of variables are involved in the design of cable-stayed bridges. Those include overall geometric dimensions, cross-sectional dimensions, number of stay-cables and pre-tensioning forces to be applied to the cables. Taking all variables into …

Development Of Traffic Live Load Models For Bridge Superstructure Rating With Rbdo And Best Selection Approach, Sasan Siavashi, Christopher D. Eamon

Civil and Environmental Engineering Faculty Research Publications

Reliability-based design optimization (RBDO) is frequently used to determine optimal structural geometry and material characteristics that can best meet performance goals while considering uncertainties. In this study, the effectiveness of RBDO to develop a rating load model for a set of bridge structures is explored, as well as the use of an alternate Best Selection procedure that requires substantially less computational effort. The specific problem investigated is the development of a vehicular load model for use in bridge rating, where the objective of the optimization is to minimize the variation in reliability index across different girder types and bridge geometries. …

Sparsity Constrained Inverse Problems - Application To Vibration-Based Structural Health Monitoring, Chandler B. Smith

Graduate College Dissertations and Theses

Vibration-based structural health monitoring (SHM) seeks to detect, quantify, locate, and prognosticate damage by processing vibration signals measured while the structure is operational. The basic premise of vibration-based SHM is that damage will affect the stiffness, mass or energy dissipation properties of the structure and in turn alter its measured dynamic characteristics. In order to make SHM a practical technology it is necessary to perform damage assessment using only a minimum number of permanently installed sensors. Deducing damage at unmeasured regions of the structural domain requires solving an inverse problem that is underdetermined and(or) ill-conditioned. In addition, the effects of …

Assessment And Optimization Of Environmental Systems Using Data Analysis And Simulation., Milad Ebrahimi

Electronic Theses and Dissertations

For most environmental systems, specifically wastewater treatment plants and aquifers, a significant number of performance data variables are attained on a time series basis. Due to the interconnectedness of the variables, it is often difficult to assess over-arching trends and quantify temporal operational performance. The objective of this research study was to provide an effective means for comprehensive temporal evaluation of environmental systems. The proposed methodology used several multivariate data analyses and statistical techniques to present an assessment framework for the water quality monitoring programs as well as optimization of treatment plants and aquifer systems. The developed procedure considered the …

Technical Project Management: Union Of Systems Engineering Processes With Project Management Processes, Deyaaldeen M. Abusal

Open Access Theses & Dissertations

Today, most projects in technical fields utilize project management to complete projects as planned, and some of the projects utilize system engineering to cover the project in both technically and commercially. This Thesis investigates the relationship between Project Management (PM) and Systems Engineering (SE) to determine if a suitably professional level of management and level of quality can be achieved. When studying PM and SE separately and make a comparison between both, there is much overlap between these two mature fields. The project could be planned and completed solely by either process. This study combines both fields of Project Management …

Indonesia’S Municipal Solid Waste 3r And Waste To Energy Programs, Farizal Farizal, Radityo Aji, Amar Rachman, Nasruddin Nasruddin, Teuku Meurah Indra Mahlia

Makara Journal of Technology

Like most cities in the world, population in Indonesia continues to grow every year. Problems that can arise from this are the increasing amount of municipal solid waste (MSW) production and the growing demand for electricity. To deal with the problems, Indonesian government runs 3R (Reduce, Reuse and Recycle) and WTE (Waste to Energy) Programs simultaneously. 3R program aims to reduce the number of waste, while WTE program aims to generate electricity as an alternative energy source. This study aims to find out the optimal proportion of MSW treated through the 3R and WTE programs. For the purpose, a goal …

Calibrating And Evaluating Dynamic Rule-Based Transit-Signal-Priority Control Systems In Urban Traffic Networks, Md Didarul Alam

Civil and Environmental Engineering Dissertations

Setting the traffic controller parameters to perform effectively in real-time is a challenging task, and it entails setting several parameters to best suit some predicted traffic conditions. This study presents the framework and method that entail the application of the Response Surface Methodology (RSM) to calibrate the parameters of any control system incorporating advanced traffic management strategies (e.g., the complex integrated traffic control system developed by Ahmed and Hawas). The integrated system is a rule-based heuristic controller that reacts to specific triggering conditions, such as identification of priority transit vehicle, downstream signal congestion, and incidents by penalizing the predefined objective …

Generalized Clusterwise Regression For Simultaneous Estimation Of Optimal Pavement Clusters And Performance Models, Mukesh Khadka

UNLV Theses, Dissertations, Professional Papers, and Capstones

The existing state-of-the-art approach of Clusterwise Regression (CR) to estimate pavement performance models (PPMs) pre-specifies explanatory variables without testing their significance; as an input, this approach requires the number of clusters for a given data set. Time-consuming ‘trial and error’ methods are required to determine the optimal number of clusters. A common objective function is the minimization of the total sum of squared errors (SSE). Given that SSE decreases monotonically as a function of the number of clusters, the optimal number of clusters with minimum SSE always is the total number of data points. Hence, the minimization of SSE is …

Introduction To Water Resources Systems - University Of Colorado Boulder, Joseph Kasprzyk

All ECSTATIC Materials

This is the introductory lecture to a Water Resource Systems and Management class from Spring 2017 at the University of Colorado Boulder, by Joseph Kasprzyk. Learning goals include (i) defining integrated water resources management, (ii) identifying Colorado water management issues (ii) identifying how RiverWare simulation and optimization can be used to develop water plans (iii) use the HyMod model to perform rainfall-runoff modeling (iv) generating random parameter samples and understanding how parameter uncertainty affects model results.

Risk-Based Decision Making Support For Construction Corporate Resource Management, Reza Sheykhi

FIU Electronic Theses and Dissertations

Competitive bidding typically challenges contractors to stay in business by reducing contingency and limiting profit margin, which imposes more prudent resource utilization and allocation decisions during both planning and construction phases of projects. Many of these decisions must be made considering uncertainties that affect resource production and construction performance through several factors such as weather, managerial practices, job-type, and market conditions, etc. Construction decision makers will therefore have varied approaches to deal with these uncertainties based on their risk utility or perception. This research presents the development of a model for investigating the impact of risk-based approaches on construction network …

Leveraging The Information Content Of Process-Based Models Using Differential Evolution And The Extended Kalman Filter, Lucas Howard

Graduate College Dissertations and Theses

Process-based models are used in a diverse array of fields, including environmental engineering to provide supporting information to engineers, policymakers and stakeholdes. Recent advances in remote sensing and data storage technology have provided opportunities for improving the application of process-based models and visualizing data, but also present new challenges. The availability of larger quantities of data may allow models to be constructed and calibrated in a more thorough and precise manner, but depending on the type and volume of data, it is not always clear how to incorporate the information content of these data into a coherent modeling framework. In …

Enhanced Pump Schedule Optimization For Large Water Distribution Networks To Maximize Environmental And Economic Benefits, Seyed Mohsen Sadatiyan Abkenar

Wayne State University Dissertations

For more than four decades researchers tried to develop optimization method and tools to reduce electricity consumption of pump stations of water distribution systems. Based on this ongoing research trend, about a decade ago, some commercial pump operation optimization software introduced to the market. Using metaheuristic and evolutionary techniques (e.g. Genetic Algorithm) make some commercial and research tools able to optimize the electricity cost of small water distribution systems (WDS). Still reducing the environmental footprint of these systems and dealing with large and complicated water distribution system is a challenge.

In this study, we aimed to develop a multiobjective optimization …

Engineering Optimization: Methods/Applications - Colorado State University, John Labadie

All ECSTATIC Materials

This course provides a comprehensive treatment of methods of optimization with focus on linear programming and its extensions, network flow optimization, integer programming, quadratic programming, and an introduction to nonlinear programming. The goal is to maintain a balance between theory, numerical computation, problem setup for solution by computer algorithms, and engineering applications. Course taught at Colorado State University.

Environmental Systems Analysis - Hong Kong University Of Science And Technology, Hong Kong, Ng Tze Ling

All ECSTATIC Materials

Undergraduate course in environmental systems analysis offered at Hong Kong University of Science and Technology, Hong Kong in Fall 2015.

Water Resources Systems Analysis - University Of Texas San Antonio, Marcio Giacomoni

All ECSTATIC Materials

Systems Analysis methods use algorithmic and mathematical approaches for problem-solving. These are powerful methods that can be applied to solve complex design and management problems for water resources systems and other engineering areas. This class will focus on optimization methods, such as linear programming, integer programming, nonlinear programming, genetic algorithms, and dynamic programming, and their application to water resources systems. Advanced Systems Analysis methods, including sensitivity analysis, alternatives generation, and multi-objective optimization will be introduced to address the complexities associated with public sector decision-making. Course taught at University of Texas San Antonio.